From: Linux.HWI@garmin.com (J.D. Schroeder)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 1/3] DRA7: Fix clock data for gmac_gmii_ref_clk_div
Date: Mon, 2 May 2016 12:12:01 -0500 [thread overview]
Message-ID: <1462209123-7332-2-git-send-email-Linux.HWI@garmin.com> (raw)
In-Reply-To: <1462209123-7332-1-git-send-email-Linux.HWI@garmin.com>
From: "J.D. Schroeder" <jay.schroeder@garmin.com>
This commit fixes the clock data inside the DRA7xx clocks device tree
structure for the gmac_gmii_ref_clk_div clock. This clock is actually
the GMAC_MAIN_CLK and has nothing to do with the register at address
0x4a0093d0. If CLKSEL_REF bit 24 inside of CM_GMAC_GMAC_CLKCTRL, is
set to 1 in order to use the GMAC_RMII_CLK instead of the
GMAC_RMII_HS_CLK, the kernel generates a clock divider warning:
WARNING: CPU: 0 PID: 0 at drivers/clk/clk-divider.c:129 clk_divider_recalc_rate+0xa8/0xe0()
gmac_gmii_ref_clk_div: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not set
By properly configuring the gmac_gmii_ref_clk_div (GMAC_MAIN_CLK) to
have the parent of dpll_gmac_m2_ck always divided by 2 the warning is
resolved and the clock tree is fixed up.
Additionally, a new clock called rmii_50mhz_clk_mux is defined that
does utilize CM_GMAC_GMAC_CLKCTRL[24] CLKSEL_REF to configure the
source clock for the RMII_50MHZ_CLK.
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Reviewed-by: Trenton Andres <trenton.andres@garmin.com>
---
arch/arm/boot/dts/dra7xx-clocks.dtsi | 15 +++++++++++----
1 file changed, 11 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/dra7xx-clocks.dtsi b/arch/arm/boot/dts/dra7xx-clocks.dtsi
index 8378b44..3f0c61d 100644
--- a/arch/arm/boot/dts/dra7xx-clocks.dtsi
+++ b/arch/arm/boot/dts/dra7xx-clocks.dtsi
@@ -1718,13 +1718,20 @@
reg = <0x0c00>;
};
- gmac_gmii_ref_clk_div: gmac_gmii_ref_clk_div at 13d0 {
+ rmii_50mhz_clk_mux: rmii_50mhz_clk_mux at 13d0 {
#clock-cells = <0>;
- compatible = "ti,divider-clock";
- clocks = <&dpll_gmac_m2_ck>;
+ compatible = "ti,mux-clock";
+ clocks = <&dpll_gmac_h11x2_ck>, <&rmii_clk_ck>;
ti,bit-shift = <24>;
reg = <0x13d0>;
- ti,dividers = <2>;
+ };
+
+ gmac_gmii_ref_clk_div: gmac_gmii_ref_clk_div {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_gmac_m2_ck>;
+ clock-mult = <1>;
+ clock-div = <2>;
};
gmac_rft_clk_mux: gmac_rft_clk_mux at 13d0 {
--
1.9.1
next prev parent reply other threads:[~2016-05-02 17:12 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-04-26 17:54 [PATCH 0/3] AM57/DRA7 Clock Tree DTSI Fix-ups J.D. Schroeder
2016-04-26 17:54 ` [PATCH 1/3] DRA7: Fix clock data for gmac_gmii_ref_clk_div J.D. Schroeder
2016-04-27 11:21 ` Tero Kristo
2016-04-27 16:36 ` Tony Lindgren
2016-04-27 17:16 ` Tony Lindgren
2016-05-02 17:12 ` [PATCH v2 0/3] AM57/DRA7 Clock Tree DTSI Fix-ups J.D. Schroeder
2016-05-02 17:12 ` J.D. Schroeder [this message]
2016-05-02 17:12 ` [PATCH v2 2/3] ARM: DRA7x: dts: Update the OSC_32K_CLK frequency J.D. Schroeder
2016-05-03 8:16 ` Tero Kristo
2016-05-03 13:31 ` J.D. Schroeder
2016-05-03 16:43 ` Tony Lindgren
2016-05-03 17:32 ` Tero Kristo
2016-05-03 17:49 ` J.D. Schroeder
2016-05-03 18:08 ` Tony Lindgren
2016-05-03 18:08 ` Tero Kristo
2016-05-03 23:17 ` Nishanth Menon
2016-05-04 14:09 ` Matthijs van Duin
2016-05-02 17:12 ` [PATCH v2 3/3] ARM: dts: dra7: fix clock node definition to avoid build warning J.D. Schroeder
2016-05-03 4:20 ` [PATCH v2 0/3] AM57/DRA7 Clock Tree DTSI Fix-ups Lokesh Vutla
2016-04-26 17:54 ` [PATCH 2/3] ARM: DRA7x: dts: Fix the 32kHz clock calculation J.D. Schroeder
2016-04-27 11:40 ` Tero Kristo
2016-04-27 14:06 ` J.D. Schroeder
2016-04-27 19:47 ` Tero Kristo
2016-04-27 20:13 ` J.D. Schroeder
2016-04-26 17:54 ` [PATCH 3/3] ARM: DRA7x: dts: Update the OSC_32K_CLK frequency J.D. Schroeder
2016-04-27 11:49 ` Tero Kristo
2016-04-27 14:20 ` J.D. Schroeder
2016-04-26 18:13 ` [PATCH 0/3] AM57/DRA7 Clock Tree DTSI Fix-ups Tony Lindgren
2016-04-26 19:18 ` J.D. Schroeder
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1462209123-7332-2-git-send-email-Linux.HWI@garmin.com \
--to=linux.hwi@garmin.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).