[PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[p.zabel@pengutronix.de (Philipp Zabel)]

Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> The mtk_hdmi_send_infoframe have to
> be run after PLL and PIXEL clock of HDMI enable.
> Make sure that HDMI inforframes can be sent
> successfully.
> 
> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
>  1 file changed, 12 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> index ba812ef..d8609f5 100644
> --- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> @@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
>  	phy_power_on(hdmi->phy);
>  	mtk_hdmi_aud_output_config(hdmi, mode);
>  
> -	mtk_hdmi_setup_audio_infoframe(hdmi);
> -	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> -	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> -	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> -		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> -
>  	mtk_hdmi_hw_vid_black(hdmi, false);
>  	mtk_hdmi_hw_aud_unmute(hdmi);
>  	mtk_hdmi_hw_send_av_unmute(hdmi);
> @@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
>  	hdmi->powered = true;
>  }
>  
> +static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
> +				    struct drm_display_mode *mode)
> +{
> +	mtk_hdmi_setup_audio_infoframe(hdmi);
> +	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> +	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> +	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> +		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> +}
> +
>  static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
>  {
>  	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
>  
> +	phy_power_on(hdmi->phy);
>  	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
>  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
>  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
> -	phy_power_on(hdmi->phy);

This change is not described in the patch description. Why is the phy
power on moved after the pixel clock enable?

> +	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
>  
>  	hdmi->enabled = true;
>  }

regards
Philipp