From mboxrd@z Thu Jan 1 00:00:00 1970 From: peter.chen@nxp.com (Peter Chen) Date: Mon, 15 Aug 2016 17:13:17 +0800 Subject: [PATCH v6 7/8] ARM: dts: imx6qdl-udoo.dtsi: fix onboard USB HUB property In-Reply-To: <1471252398-957-1-git-send-email-peter.chen@nxp.com> References: <1471252398-957-1-git-send-email-peter.chen@nxp.com> Message-ID: <1471252398-957-8-git-send-email-peter.chen@nxp.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org The current dts describes USB HUB's property at USB controller's entry, it is improper. The USB HUB should be the child node under USB controller, and power sequence properties are under it. Besides, using gpio pinctrl setting for USB2415's reset pin. Signed-off-by: Peter Chen Signed-off-by: Joshua Clayton --- arch/arm/boot/dts/imx6qdl-udoo.dtsi | 26 ++++++++++++-------------- 1 file changed, 12 insertions(+), 14 deletions(-) diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/imx6qdl-udoo.dtsi index 3bee2f9..87fe31f 100644 --- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi +++ b/arch/arm/boot/dts/imx6qdl-udoo.dtsi @@ -9,6 +9,8 @@ * */ +#include + / { aliases { backlight = &backlight; @@ -58,17 +60,6 @@ #address-cells = <1>; #size-cells = <0>; - reg_usb_h1_vbus: regulator at 0 { - compatible = "regulator-fixed"; - reg = <0>; - regulator-name = "usb_h1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - startup-delay-us = <2>; /* USB2415 requires a POR of 1 us minimum */ - gpio = <&gpio7 12 0>; - }; - reg_panel: regulator at 1 { compatible = "regulator-fixed"; reg = <1>; @@ -188,7 +179,7 @@ pinctrl_usbh: usbhgrp { fsl,pins = < - MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0 >; }; @@ -259,9 +250,16 @@ &usbh1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usbh>; - vbus-supply = <®_usb_h1_vbus>; - clocks = <&clks IMX6QDL_CLK_CKO>; status = "okay"; + + usb2415: hub at 1 { + compatible = "usb424,2514"; + reg = <1>; + + clocks = <&clks IMX6QDL_CLK_CKO>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + reset-duration-us = <3000>; + }; }; &usdhc3 { -- 1.9.1