From mboxrd@z Thu Jan 1 00:00:00 1970 From: linus.walleij@linaro.org (Linus Walleij) Date: Fri, 9 Sep 2016 23:25:35 +0200 Subject: [PATCH 6/6] ARM: dts: add the CLCD LCD display to the NHK15 In-Reply-To: <1473456335-22767-1-git-send-email-linus.walleij@linaro.org> References: <1473456335-22767-1-git-send-email-linus.walleij@linaro.org> Message-ID: <1473456335-22767-7-git-send-email-linus.walleij@linaro.org> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org This adds the TPG110 TDO43MTEA2 24-bit RGB LCD panel and sets up the Nomadik device tree to activate the CLCD and connect it to this panel. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-nomadik-nhk15.dts | 44 ++++++++++++++++++++++++++++++ arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 22 +++++++++++++++ 2 files changed, 66 insertions(+) diff --git a/arch/arm/boot/dts/ste-nomadik-nhk15.dts b/arch/arm/boot/dts/ste-nomadik-nhk15.dts index 3ec5c653ad56..1ec46a794a4d 100644 --- a/arch/arm/boot/dts/ste-nomadik-nhk15.dts +++ b/arch/arm/boot/dts/ste-nomadik-nhk15.dts @@ -176,6 +176,50 @@ }; amba { + clcd at 10120000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&clcd_24bit_mux>; + port { + nomadik_clcd_pads: endpoint { + remote-endpoint = <&nomadik_clcd_panel>; + arm,pl11x,tft-r0g0b0-pads = <16 8 0>; + }; + }; + + /* + * WVGA connector 21 + * WVGA (800x480): 4.3" TPG110 TDO43MTEA2 24-bit RGB + * with TPO touch screen. + */ + panel { + compatible = "tpo,tpg110", "panel-dpi"; + grestb-gpios = <&stmpe_gpio44 5 GPIO_ACTIVE_LOW>; + scen-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + scl-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + backlight = <&bl>; + + port { + nomadik_clcd_panel: endpoint { + remote-endpoint = <&nomadik_clcd_pads>; + }; + }; + + panel-timing { + clock-frequency = <33200000>; + hactive = <800>; + hback-porch = <216>; + hfront-porch = <40>; + hsync-len = <1>; + vactive = <480>; + vback-porch = <35>; + vfront-porch = <10>; + vsync-len = <1>; + }; + }; + }; + /* Activate RX/TX and CTS/RTS on UART 0 */ uart0: uart at 101fd000 { pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi index 80a3c9ccccd9..adb1c0998b81 100644 --- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi +++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi @@ -166,6 +166,18 @@ }; }; }; + clcd { + /* + * This should be activated to use the additional + * 8 lines for bits 16 thru 23 from the CLCD block. + */ + clcd_24bit_mux: clcd_mux { + clcd_24bit_mux { + function = "clcd"; + groups = "clcd_16_23_b_1"; + }; + }; + }; }; /* Power Management Unit */ @@ -732,6 +744,16 @@ #size-cells = <1>; ranges; + clcd at 10120000 { + compatible = "arm,pl110", "arm,primecell"; + reg = <0x10120000 0x1000>; + interrupt-names = "combined"; + interrupts = <14>; + clocks = <&clcdclk>, <&hclkclcd>; + clock-names = "clcdclk", "apb_pclk"; + status = "disabled"; + }; + vica: intc at 10140000 { compatible = "arm,versatile-vic"; interrupt-controller; -- 2.7.4