From: benjamin.gaignard@linaro.org (Benjamin Gaignard)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 7/7] ARM: dts: stm32: add stm32 general purpose timer driver in DT
Date: Thu, 24 Nov 2016 16:14:23 +0100 [thread overview]
Message-ID: <1480000463-9625-8-git-send-email-benjamin.gaignard@st.com> (raw)
In-Reply-To: <1480000463-9625-1-git-send-email-benjamin.gaignard@st.com>
Add general purpose timers and it sub-nodes into DT for stm32f4.
Define and enable pwm1 and pwm3 for stm32f469 discovery board
version 2:
- use parameters to describe hardware capabilities
- do not use references for pwm and iio timer subnodes
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
---
arch/arm/boot/dts/stm32f429.dtsi | 305 +++++++++++++++++++++++++++++++++-
arch/arm/boot/dts/stm32f469-disco.dts | 28 ++++
2 files changed, 332 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
index bca491d..8f217b1 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -48,7 +48,7 @@
#include "skeleton.dtsi"
#include "armv7-m.dtsi"
#include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
-
+#include <dt-bindings/iio/timer/st,stm32-iio-timer.h>
/ {
clocks {
clk_hse: clk-hse {
@@ -355,6 +355,21 @@
slew-rate = <2>;
};
};
+
+ pwm1_pins: pwm at 1 {
+ pins {
+ pinmux = <STM32F429_PA8_FUNC_TIM1_CH1>,
+ <STM32F429_PB13_FUNC_TIM1_CH1N>,
+ <STM32F429_PB12_FUNC_TIM1_BKIN>;
+ };
+ };
+
+ pwm3_pins: pwm at 3 {
+ pins {
+ pinmux = <STM32F429_PB4_FUNC_TIM3_CH1>,
+ <STM32F429_PB5_FUNC_TIM3_CH2>;
+ };
+ };
};
rcc: rcc at 40023810 {
@@ -426,6 +441,294 @@
interrupts = <80>;
clocks = <&rcc 0 38>;
};
+
+ gptimer1: gptimer1 at 40010000 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40010000 0x400>;
+ clocks = <&rcc 0 160>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm1 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <4>;
+ st,breakinput;
+ st,complementary;
+ status = "disabled";
+ };
+
+ iiotimer1 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <27>;
+ st,input-triggers-names = TIM5_TRGO,
+ TIM2_TRGO,
+ TIM4_TRGO,
+ TIM3_TRGO;
+ st,output-triggers-names = TIM1_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer2: gptimer2 at 40000000 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40000000 0x400>;
+ clocks = <&rcc 0 128>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm2 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <4>;
+ st,32bits-counter;
+ status = "disabled";
+ };
+
+ iiotimer2 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <28>;
+ st,input-triggers-names = TIM1_TRGO,
+ TIM8_TRGO,
+ TIM3_TRGO,
+ TIM4_TRGO;
+ st,output-triggers-names = TIM2_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer3: gptimer3 at 40000400 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40000400 0x400>;
+ clocks = <&rcc 0 129>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm3 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <4>;
+ status = "disabled";
+ };
+
+ iiotimer3 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <29>;
+ st,input-triggers-names = TIM1_TRGO,
+ TIM8_TRGO,
+ TIM5_TRGO,
+ TIM4_TRGO;
+ st,output-triggers-names = TIM3_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer4: gptimer4 at 40000800 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40000800 0x400>;
+ clocks = <&rcc 0 130>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm4 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <4>;
+ status = "disabled";
+ };
+
+ iiotimer4 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <30>;
+ st,input-triggers-names = TIM1_TRGO,
+ TIM2_TRGO,
+ TIM3_TRGO,
+ TIM8_TRGO;
+ st,output-triggers-names = TIM4_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer5: gptimer5 at 40000C00 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40000C00 0x400>;
+ clocks = <&rcc 0 131>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm5 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <4>;
+ st,32bits-counter;
+ status = "disabled";
+ };
+
+ iiotimer5 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <50>;
+ st,input-triggers-names = TIM2_TRGO,
+ TIM3_TRGO,
+ TIM4_TRGO,
+ TIM8_TRGO;
+ st,output-triggers-names = TIM5_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer6: gptimer6 at 40001000 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40001000 0x400>;
+ clocks = <&rcc 0 132>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ iiotimer6 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <54>;
+ st,output-triggers-names = TIM6_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer7: gptimer7 at 40001400 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40001400 0x400>;
+ clocks = <&rcc 0 133>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ iiotimer7 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <55>;
+ st,output-triggers-names = TIM7_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer8: gptimer8 at 40010400 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40010400 0x400>;
+ clocks = <&rcc 0 161>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm8 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <4>;
+ st,complementary;
+ st,breakinput;
+ status = "disabled";
+ };
+
+ iiotimer8 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <46>;
+ st,input-triggers-names = TIM1_TRGO,
+ TIM2_TRGO,
+ TIM4_TRGO,
+ TIM5_TRGO;
+ st,output-triggers-names = TIM8_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer9: gptimer9 at 40014000 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40014000 0x400>;
+ clocks = <&rcc 0 176>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm9 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <2>;
+ status = "disabled";
+ };
+
+ iiotimer9 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <24>;
+ st,input-triggers-names = TIM2_TRGO,
+ TIM3_TRGO;
+ st,output-triggers-names = TIM9_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer10: gptimer10 at 40014400 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40014400 0x400>;
+ clocks = <&rcc 0 177>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm10 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <1>;
+ status = "disabled";
+ };
+ };
+
+ gptimer11: gptimer11 at 40014800 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40014800 0x400>;
+ clocks = <&rcc 0 178>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm11 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <1>;
+ status = "disabled";
+ };
+ };
+
+ gptimer12: gptimer12 at 40001800 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40001800 0x400>;
+ clocks = <&rcc 0 134>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm12 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <2>;
+ status = "disabled";
+ };
+
+ iiotimer12 at 0 {
+ compatible = "st,stm32-iio-timer";
+ interrupts = <43>;
+ st,input-triggers-names = TIM4_TRGO,
+ TIM5_TRGO;
+ st,output-triggers-names = TIM12_TRGO;
+ status = "disabled";
+ };
+ };
+
+ gptimer13: gptimer13 at 40001C00 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40001C00 0x400>;
+ clocks = <&rcc 0 135>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm13 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <1>;
+ status = "disabled";
+ };
+ };
+
+ gptimer14: gptimer14 at 40002000 {
+ compatible = "st,stm32-gptimer";
+ reg = <0x40002000 0x400>;
+ clocks = <&rcc 0 136>;
+ clock-names = "clk_int";
+ status = "disabled";
+
+ pwm14 at 0 {
+ compatible = "st,stm32-pwm";
+ st,pwm-num-chan = <1>;
+ status = "disabled";
+ };
+ };
};
};
diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/stm32f469-disco.dts
index 8a163d7..0c93846 100644
--- a/arch/arm/boot/dts/stm32f469-disco.dts
+++ b/arch/arm/boot/dts/stm32f469-disco.dts
@@ -81,3 +81,31 @@
&usart3 {
status = "okay";
};
+
+&gptimer1 {
+ status = "okay";
+
+ pwm1 at 0 {
+ pinctrl-0 = <&pwm1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ iiotimer1 at 0 {
+ status = "okay";
+ };
+};
+
+&gptimer3 {
+ status = "okay";
+
+ pwm3 at 0 {
+ pinctrl-0 = <&pwm3_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ iiotimer3 at 0 {
+ status = "okay";
+ };
+};
--
1.9.1
prev parent reply other threads:[~2016-11-24 15:14 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-11-24 15:14 [PATCH v2 0/7] Add pwm and IIO timer drivers for stm32 Benjamin Gaignard
2016-11-24 15:14 ` [PATCH v2 1/7] MFD: add bindings for stm32 general purpose timer driver Benjamin Gaignard
2016-11-27 14:10 ` Jonathan Cameron
2016-11-27 15:41 ` Jonathan Cameron
2016-11-29 8:48 ` Benjamin Gaignard
2016-12-03 9:14 ` Jonathan Cameron
2016-11-24 15:14 ` [PATCH v2 2/7] MFD: add " Benjamin Gaignard
2016-11-24 15:14 ` [PATCH v2 3/7] PWM: add pwm-stm32 DT bindings Benjamin Gaignard
2016-11-27 14:19 ` Jonathan Cameron
2016-11-30 21:20 ` Rob Herring
2016-12-01 8:44 ` Benjamin Gaignard
2016-11-24 15:14 ` [PATCH v2 4/7] PWM: add pwm driver for stm32 plaftorm Benjamin Gaignard
2016-11-24 15:14 ` [PATCH v2 5/7] IIO: add bindings for stm32 IIO timer driver Benjamin Gaignard
2016-11-27 14:25 ` Jonathan Cameron
2016-11-27 15:45 ` Benjamin Gaignard
2016-11-27 15:51 ` Jonathan Cameron
2016-11-24 15:14 ` [PATCH v2 6/7] IIO: add STM32 " Benjamin Gaignard
2016-11-27 15:42 ` Jonathan Cameron
2016-11-29 9:46 ` Benjamin Gaignard
2016-12-03 9:28 ` Jonathan Cameron
2016-11-24 15:14 ` Benjamin Gaignard [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1480000463-9625-8-git-send-email-benjamin.gaignard@st.com \
--to=benjamin.gaignard@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).