From: slongerbeam@gmail.com (Steve Longerbeam)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 09/12] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder
Date: Wed, 7 Dec 2016 16:57:50 -0800 [thread overview]
Message-ID: <1481158673-15937-10-git-send-email-steve_longerbeam@mentor.com> (raw)
In-Reply-To: <1481158673-15937-1-git-send-email-steve_longerbeam@mentor.com>
Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.
On the sabreauto, two analog video inputs are routed to the ADV7180,
composite on Ain1, and composite on Ain3. Those inputs are defined
via inputs and input-names under the ADV7180 node. The ADV7180 power
pin is via max7310_b port expander.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
---
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 62 ++++++++++++++++++++++++++++++++
1 file changed, 62 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index d74882a..9222026 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -147,10 +147,48 @@
gpio-controller;
#gpio-cells = <2>;
};
+
+ camera: adv7180 at 21 {
+ compatible = "adi,adv7180";
+ reg = <0x21>;
+ powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <27 0x8>;
+ inputs = <0x00 0x02>;
+ input-names = "ADV7180 Composite on Ain1",
+ "ADV7180 Composite on Ain3";
+
+ port {
+ adv7180_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <8>;
+ };
+ };
+ };
};
};
};
+&ipu1_smfc0 {
+ fim {
+ enable = <1>;
+ };
+};
+
+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <8>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
+ bus-width = <8>;
+};
+
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
&clks {
assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
<&clks IMX6QDL_PLL4_BYPASS>,
@@ -451,6 +489,30 @@
>;
};
+ pinctrl_ipu1_csi0: ipu1grp-csi0 {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04 0x80000000
+ MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05 0x80000000
+ MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06 0x80000000
+ MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07 0x80000000
+ MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08 0x80000000
+ MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09 0x80000000
+ MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10 0x80000000
+ MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11 0x80000000
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000
+ >;
+ };
+
pinctrl_pwm3: pwm1grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
--
2.7.4
next prev parent reply other threads:[~2016-12-08 0:57 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-08 0:57 [PATCH 00/12] i.MX media devices and connections Steve Longerbeam
2016-12-08 0:57 ` [PATCH 01/12] ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node Steve Longerbeam
2016-12-08 0:57 ` [PATCH 02/12] ARM: dts: imx6qdl: rename ipu client nodes Steve Longerbeam
2016-12-09 11:39 ` Philipp Zabel
2016-12-08 0:57 ` [PATCH 03/12] ARM: dts: imx6qdl: add video capture devices and connections Steve Longerbeam
2016-12-08 0:57 ` [PATCH 04/12] ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors Steve Longerbeam
2016-12-08 0:57 ` [PATCH 05/12] ARM: dts: imx6-sabresd: " Steve Longerbeam
2016-12-08 0:57 ` [PATCH 06/12] ARM: dts: imx6-sabreauto: create i2cmux for i2c3 Steve Longerbeam
2016-12-08 0:57 ` [PATCH 07/12] ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b Steve Longerbeam
2016-12-08 0:57 ` [PATCH 08/12] ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture Steve Longerbeam
2016-12-08 0:57 ` Steve Longerbeam [this message]
2016-12-08 0:57 ` [PATCH 10/12] gpu: ipu-v3: Add ipu_unit_type enumeration Steve Longerbeam
2016-12-08 0:57 ` [PATCH 11/12] gpu: ipu-v3: lookup ipu client nodes by name Steve Longerbeam
2016-12-08 0:57 ` [PATCH 12/12] gpu: ipu-v3: Add smfc and ic client devices Steve Longerbeam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1481158673-15937-10-git-send-email-steve_longerbeam@mentor.com \
--to=slongerbeam@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox