From mboxrd@z Thu Jan 1 00:00:00 1970 From: dawei.chien@mediatek.com (Dawei Chien) Date: Mon, 16 Jan 2017 11:46:44 +0800 Subject: [PATCH v2 6/6] arm: dts: mt2701: Add thermal device node. In-Reply-To: <1484538290.13258.3.camel@mtksdaap41> References: <1484296978-18572-1-git-send-email-erin.lo@mediatek.com> <1484296978-18572-7-git-send-email-erin.lo@mediatek.com> <1484538290.13258.3.camel@mtksdaap41> Message-ID: <1484538404.13258.4.camel@mtksdaap41> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org On Mon, 2017-01-16 at 11:44 +0800, Dawei Chien wrote: > On Fri, 2017-01-13 at 16:27 +0100, Matthias Brugger wrote: > > > > On 13/01/17 09:42, Erin Lo wrote: > > > From: Dawei Chien > > > > > > Add thermal controller device nodes for MT2701. > > > > > > Signed-off-by: Dawei Chien > > > Signed-off-by: Erin Lo > > > --- > > > arch/arm/boot/dts/mt2701.dtsi | 43 +++++++++++++++++++++++++++++++++++++++++++ > > > 1 file changed, 43 insertions(+) > > > > > > diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi > > > index 3847f70..c43d5f8 100644 > > > --- a/arch/arm/boot/dts/mt2701.dtsi > > > +++ b/arch/arm/boot/dts/mt2701.dtsi > > > @@ -89,6 +89,36 @@ > > > clock-output-names = "rtc32k"; > > > }; > > > > > > + thermal-zones { > > > + cpu_thermal: cpu_thermal { > > > + polling-delay-passive = <1000>; /* milliseconds */ > > > + polling-delay = <1000>; /* milliseconds */ > > > + > > > + thermal-sensors = <&thermal 0>; > > > + sustainable-power = <1000>; > > > + > > > + trips { > > > + threshold: trip-point at 0 { > > > + temperature = <68000>; > > > + hysteresis = <2000>; > > > + type = "passive"; > > > + }; > > > + > > > + target: trip-point at 1 { > > > + temperature = <85000>; > > > + hysteresis = <2000>; > > > + type = "passive"; > > > + }; > > > + > > > + cpu_crit: cpu_crit at 0 { > > > + temperature = <115000>; > > > + hysteresis = <2000>; > > > + type = "critical"; > > > + }; > > > + }; > > > + }; > > > + }; > > > + > > > timer { > > > compatible = "arm,armv7-timer"; > > > interrupt-parent = <&gic>; > > > @@ -270,6 +300,19 @@ > > > status = "disabled"; > > > }; > > > > > > + thermal: thermal at 1100b000 { > > > + #thermal-sensor-cells = <0>; > > > + compatible = "mediatek,mt2701-thermal"; > > > + reg = <0 0x1100b000 0 0x1000>; > > > + interrupts = ; > > > + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>; > > > + clock-names = "therm", "auxadc"; > > > + resets = <&pericfg 0x10>; > > > > should be MT2701_PERI_AUXADC_SW_RST, right? > > > Thank you for your reminding, I didn't realize mt2701-resets.h upstream > already, I would update on next version, thank you. > > resets = <&pericfg MT2701_PERI_AUXADC_SW_RST>; Actually, Should be MT2701_PERI_THERM_SW_RST. resets = <&pericfg MT2701_PERI_THERM_SW_RST>; > > > + reset-names = "therm"; > > > + mediatek,auxadc = <&auxadc>; > > > + mediatek,apmixedsys = <&apmixedsys>; > > > + }; > > > + > > > nandc: nfi at 1100d000 { > > > compatible = "mediatek,mt2701-nfc"; > > > reg = <0 0x1100d000 0 0x1000>; > > > >