[PATCH 04/10] clocksource/drivers/tcb_clksrc: Use 32 bit tcb as sched_clock

[PATCH 04/10] clocksource/drivers/tcb_clksrc: Use 32 bit tcb as sched_clock

[Daniel Lezcano]

From: David Engraf <david.engraf@sysgo.com>

On newer boards the TC can be read as single 32 bit value without locking.
Thus the clock can be used as reference for sched_clock which is much more
accurate than the jiffies implementation.

Tested on a Atmel SAMA5D2 board.

Signed-off-by: David Engraf <david.engraf@sysgo.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
---
 drivers/clocksource/tcb_clksrc.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/clocksource/tcb_clksrc.c b/drivers/clocksource/tcb_clksrc.c
index d4ca996..745844e 100644
--- a/drivers/clocksource/tcb_clksrc.c
+++ b/drivers/clocksource/tcb_clksrc.c
@@ -10,6 +10,7 @@
 #include <linux/io.h>
 #include <linux/platform_device.h>
 #include <linux/atmel_tc.h>
+#include <linux/sched_clock.h>
 
 
 /*
@@ -56,11 +57,16 @@ static u64 tc_get_cycles(struct clocksource *cs)
 	return (upper << 16) | lower;
 }
 
-static u64 tc_get_cycles32(struct clocksource *cs)
+static u32 tc_get_cv32(void)
 {
 	return __raw_readl(tcaddr + ATMEL_TC_REG(0, CV));
 }
 
+static u64 tc_get_cycles32(struct clocksource *cs)
+{
+	return tc_get_cv32();
+}
+
 static struct clocksource clksrc = {
 	.name           = "tcb_clksrc",
 	.rating         = 200,
@@ -69,6 +75,11 @@ static struct clocksource clksrc = {
 	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
+static u64 notrace tc_read_sched_clock(void)
+{
+	return tc_get_cv32();
+}
+
 #ifdef CONFIG_GENERIC_CLOCKEVENTS
 
 struct tc_clkevt_device {
@@ -339,6 +350,9 @@ static int __init tcb_clksrc_init(void)
 		clksrc.read = tc_get_cycles32;
 		/* setup ony channel 0 */
 		tcb_setup_single_chan(tc, best_divisor_idx);
+
+		/* register sched_clock on chips with single 32 bit counter */
+		sched_clock_register(tc_read_sched_clock, 32, divided_rate);
 	} else {
 		/* tclib will give us three clocks no matter what the
 		 * underlying platform supports.
-- 
2.7.4

[PATCH 06/10] clocksource/drivers/ostm: Add renesas-ostm timer driver

[Daniel Lezcano]

From: Chris Brandt <chris.brandt@renesas.com>

This patch adds a OSTM driver for the Renesas architecture.
The OS Timer (OSTM) has independent channels that can be
used as a freerun or interval times.
This driver uses the first probed device as a clocksource
and then any additional devices as clock events.

Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
---
 arch/arm/mach-shmobile/Kconfig     |   1 +
 drivers/clocksource/Kconfig        |   7 +
 drivers/clocksource/Makefile       |   1 +
 drivers/clocksource/renesas-ostm.c | 265 +++++++++++++++++++++++++++++++++++++
 4 files changed, 274 insertions(+)
 create mode 100644 drivers/clocksource/renesas-ostm.c

diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 2bb4b09..ad7d604 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -57,6 +57,7 @@ config ARCH_R7S72100
 	select PM
 	select PM_GENERIC_DOMAINS
 	select SYS_SUPPORTS_SH_MTU2
+	select RENESAS_OSTM
 
 config ARCH_R8A73A4
 	bool "R-Mobile APE6 (R8A73A40)"
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index afef0e8..4002d6d 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -484,6 +484,13 @@ config SH_TIMER_MTU2
 	  Timer Pulse Unit 2 (MTU2) hardware available on SoCs from Renesas.
 	  This hardware comes with 16 bit-timer registers.
 
+config RENESAS_OSTM
+	bool "Renesas OSTM timer driver" if COMPILE_TEST
+	depends on GENERIC_CLOCKEVENTS
+	select CLKSRC_MMIO
+	help
+	  Enables the support for the Renesas OSTM.
+
 config SH_TIMER_TMU
 	bool "Renesas TMU timer driver" if COMPILE_TEST
 	depends on GENERIC_CLOCKEVENTS
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index dbbee80..d227d13 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_CS5535_CLOCK_EVENT_SRC)	+= cs5535-clockevt.o
 obj-$(CONFIG_CLKSRC_JCORE_PIT)		+= jcore-pit.o
 obj-$(CONFIG_SH_TIMER_CMT)	+= sh_cmt.o
 obj-$(CONFIG_SH_TIMER_MTU2)	+= sh_mtu2.o
+obj-$(CONFIG_RENESAS_OSTM)	+= renesas-ostm.o
 obj-$(CONFIG_SH_TIMER_TMU)	+= sh_tmu.o
 obj-$(CONFIG_EM_TIMER_STI)	+= em_sti.o
 obj-$(CONFIG_CLKBLD_I8253)	+= i8253.o
diff --git a/drivers/clocksource/renesas-ostm.c b/drivers/clocksource/renesas-ostm.c
new file mode 100644
index 0000000..c76f576
--- /dev/null
+++ b/drivers/clocksource/renesas-ostm.c
@@ -0,0 +1,265 @@
+/*
+ * Renesas Timer Support - OSTM
+ *
+ * Copyright (C) 2017 Renesas Electronics America, Inc.
+ * Copyright (C) 2017 Chris Brandt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/sched_clock.h>
+#include <linux/slab.h>
+
+/*
+ * The OSTM contains independent channels.
+ * The first OSTM channel probed will be set up as a free running
+ * clocksource. Additionally we will use this clocksource for the system
+ * schedule timer sched_clock().
+ *
+ * The second (or more) channel probed will be set up as an interrupt
+ * driven clock event.
+ */
+
+struct ostm_device {
+	void __iomem *base;
+	unsigned long ticks_per_jiffy;
+	struct clock_event_device ced;
+};
+
+static void __iomem *system_clock;	/* For sched_clock() */
+
+/* OSTM REGISTERS */
+#define	OSTM_CMP		0x000	/* RW,32 */
+#define	OSTM_CNT		0x004	/* R,32 */
+#define	OSTM_TE			0x010	/* R,8 */
+#define	OSTM_TS			0x014	/* W,8 */
+#define	OSTM_TT			0x018	/* W,8 */
+#define	OSTM_CTL		0x020	/* RW,8 */
+
+#define	TE			0x01
+#define	TS			0x01
+#define	TT			0x01
+#define	CTL_PERIODIC		0x00
+#define	CTL_ONESHOT		0x02
+#define	CTL_FREERUN		0x02
+
+static struct ostm_device *ced_to_ostm(struct clock_event_device *ced)
+{
+	return container_of(ced, struct ostm_device, ced);
+}
+
+static void ostm_timer_stop(struct ostm_device *ostm)
+{
+	if (readb(ostm->base + OSTM_TE) & TE) {
+		writeb(TT, ostm->base + OSTM_TT);
+
+		/*
+		 * Read back the register simply to confirm the write operation
+		 * has completed since I/O writes can sometimes get queued by
+		 * the bus architecture.
+		 */
+		while (readb(ostm->base + OSTM_TE) & TE)
+			;
+	}
+}
+
+static int __init ostm_init_clksrc(struct ostm_device *ostm, unsigned long rate)
+{
+	/*
+	 * irq not used (clock sources don't use interrupts)
+	 */
+
+	ostm_timer_stop(ostm);
+
+	writel(0, ostm->base + OSTM_CMP);
+	writeb(CTL_FREERUN, ostm->base + OSTM_CTL);
+	writeb(TS, ostm->base + OSTM_TS);
+
+	return clocksource_mmio_init(ostm->base + OSTM_CNT,
+			"ostm", rate,
+			300, 32, clocksource_mmio_readl_up);
+}
+
+static u64 notrace ostm_read_sched_clock(void)
+{
+	return readl(system_clock);
+}
+
+static void __init ostm_init_sched_clock(struct ostm_device *ostm,
+			unsigned long rate)
+{
+	system_clock = ostm->base + OSTM_CNT;
+	sched_clock_register(ostm_read_sched_clock, 32, rate);
+}
+
+static int ostm_clock_event_next(unsigned long delta,
+				     struct clock_event_device *ced)
+{
+	struct ostm_device *ostm = ced_to_ostm(ced);
+
+	ostm_timer_stop(ostm);
+
+	writel(delta, ostm->base + OSTM_CMP);
+	writeb(CTL_ONESHOT, ostm->base + OSTM_CTL);
+	writeb(TS, ostm->base + OSTM_TS);
+
+	return 0;
+}
+
+static int ostm_shutdown(struct clock_event_device *ced)
+{
+	struct ostm_device *ostm = ced_to_ostm(ced);
+
+	ostm_timer_stop(ostm);
+
+	return 0;
+}
+static int ostm_set_periodic(struct clock_event_device *ced)
+{
+	struct ostm_device *ostm = ced_to_ostm(ced);
+
+	if (clockevent_state_oneshot(ced) || clockevent_state_periodic(ced))
+		ostm_timer_stop(ostm);
+
+	writel(ostm->ticks_per_jiffy - 1, ostm->base + OSTM_CMP);
+	writeb(CTL_PERIODIC, ostm->base + OSTM_CTL);
+	writeb(TS, ostm->base + OSTM_TS);
+
+	return 0;
+}
+
+static int ostm_set_oneshot(struct clock_event_device *ced)
+{
+	struct ostm_device *ostm = ced_to_ostm(ced);
+
+	ostm_timer_stop(ostm);
+
+	return 0;
+}
+
+static irqreturn_t ostm_timer_interrupt(int irq, void *dev_id)
+{
+	struct ostm_device *ostm = dev_id;
+
+	if (clockevent_state_oneshot(&ostm->ced))
+		ostm_timer_stop(ostm);
+
+	/* notify clockevent layer */
+	if (ostm->ced.event_handler)
+		ostm->ced.event_handler(&ostm->ced);
+
+	return IRQ_HANDLED;
+}
+
+static int __init ostm_init_clkevt(struct ostm_device *ostm, int irq,
+			unsigned long rate)
+{
+	struct clock_event_device *ced = &ostm->ced;
+	int ret = -ENXIO;
+
+	ret = request_irq(irq, ostm_timer_interrupt,
+			  IRQF_TIMER | IRQF_IRQPOLL,
+			  "ostm", ostm);
+	if (ret) {
+		pr_err("ostm: failed to request irq\n");
+		return ret;
+	}
+
+	ced->name = "ostm";
+	ced->features = CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_PERIODIC;
+	ced->set_state_shutdown = ostm_shutdown;
+	ced->set_state_periodic = ostm_set_periodic;
+	ced->set_state_oneshot = ostm_set_oneshot;
+	ced->set_next_event = ostm_clock_event_next;
+	ced->shift = 32;
+	ced->rating = 300;
+	ced->cpumask = cpumask_of(0);
+	clockevents_config_and_register(ced, rate, 0xf, 0xffffffff);
+
+	return 0;
+}
+
+static int __init ostm_init(struct device_node *np)
+{
+	struct ostm_device *ostm;
+	int ret = -EFAULT;
+	struct clk *ostm_clk = NULL;
+	int irq;
+	unsigned long rate;
+
+	ostm = kzalloc(sizeof(*ostm), GFP_KERNEL);
+	if (!ostm)
+		return -ENOMEM;
+
+	ostm->base = of_iomap(np, 0);
+	if (!ostm->base) {
+		pr_err("ostm: failed to remap I/O memory\n");
+		goto err;
+	}
+
+	irq = irq_of_parse_and_map(np, 0);
+	if (irq < 0) {
+		pr_err("ostm: Failed to get irq\n");
+		goto err;
+	}
+
+	ostm_clk = of_clk_get(np, 0);
+	if (IS_ERR(ostm_clk)) {
+		pr_err("ostm: Failed to get clock\n");
+		ostm_clk = NULL;
+		goto err;
+	}
+
+	ret = clk_prepare_enable(ostm_clk);
+	if (ret) {
+		pr_err("ostm: Failed to enable clock\n");
+		goto err;
+	}
+
+	rate = clk_get_rate(ostm_clk);
+	ostm->ticks_per_jiffy = (rate + HZ / 2) / HZ;
+
+	/*
+	 * First probed device will be used as system clocksource. Any
+	 * additional devices will be used as clock events.
+	 */
+	if (!system_clock) {
+		ret = ostm_init_clksrc(ostm, rate);
+
+		if (!ret) {
+			ostm_init_sched_clock(ostm, rate);
+			pr_info("ostm: used for clocksource\n");
+		}
+
+	} else {
+		ret = ostm_init_clkevt(ostm, irq, rate);
+
+		if (!ret)
+			pr_info("ostm: used for clock events\n");
+	}
+
+err:
+	if (ret) {
+		clk_disable_unprepare(ostm_clk);
+		iounmap(ostm->base);
+		kfree(ostm);
+		return ret;
+	}
+
+	return 0;
+}
+
+CLOCKSOURCE_OF_DECLARE(ostm, "renesas,ostm", ostm_init);
-- 
2.7.4

[PATCH 08/10] clocksource/drivers/arm_arch_timer: Remove fsl-a008585 parameter

[Daniel Lezcano]

From: Ding Tianhong <dingtianhong@huawei.com>

Having a command line option to flip the errata handling for a
particular erratum is a little bit unusual, and it's vastly superior to
pass this in the DT. By common consensus, it's best to kill off the
command line parameter.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
---
 Documentation/admin-guide/kernel-parameters.txt |  9 ---------
 drivers/clocksource/arm_arch_timer.c            | 14 --------------
 2 files changed, 23 deletions(-)

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index be7c0d9..d8fc55a 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -549,15 +549,6 @@
 			loops can be debugged more effectively on production
 			systems.
 
-	clocksource.arm_arch_timer.fsl-a008585=
-			[ARM64]
-			Format: <bool>
-			Enable/disable the workaround of Freescale/NXP
-			erratum A-008585.  This can be useful for KVM
-			guests, if the guest device tree doesn't show the
-			erratum.  If unspecified, the workaround is
-			enabled based on the device tree.
-
 	clearcpuid=BITNUM [X86]
 			Disable CPUID feature X for the kernel. See
 			arch/x86/include/asm/cpufeatures.h for the valid bit
diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 4c8c3fb..6a9d031 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -101,20 +101,6 @@ EXPORT_SYMBOL_GPL(arch_timer_read_ool_enabled);
 
 static int fsl_a008585_enable = -1;
 
-static int __init early_fsl_a008585_cfg(char *buf)
-{
-	int ret;
-	bool val;
-
-	ret = strtobool(buf, &val);
-	if (ret)
-		return ret;
-
-	fsl_a008585_enable = val;
-	return 0;
-}
-early_param("clocksource.arm_arch_timer.fsl-a008585", early_fsl_a008585_cfg);
-
 u32 __fsl_a008585_read_cntp_tval_el0(void)
 {
 	return __fsl_a008585_read_reg(cntp_tval_el0);
-- 
2.7.4

[PATCH 09/10] clocksource/drivers/arm_arch_timer: Introduce generic errata handling infrastructure

[Daniel Lezcano]

From: Ding Tianhong <dingtianhong@huawei.com>

Currently we have code inline in the arch timer probe path to cater for
Freescale erratum A-008585, complete with ifdeffery. This is a little
ugly, and will get worse as we try to add more errata handling.

This patch refactors the handling of Freescale erratum A-008585. Now the
erratum is described in a generic arch_timer_erratum_workaround
structure, and the probe path can iterate over these to detect errata
and enable workarounds.

This will simplify the addition and maintenance of code handling
Hisilicon erratum 161010101.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, correct Kconfig, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
---
 arch/arm64/include/asm/arch_timer.h  | 38 +++++----------
 drivers/clocksource/Kconfig          |  4 ++
 drivers/clocksource/arm_arch_timer.c | 92 ++++++++++++++++++++++++------------
 3 files changed, 80 insertions(+), 54 deletions(-)

diff --git a/arch/arm64/include/asm/arch_timer.h b/arch/arm64/include/asm/arch_timer.h
index eaa5bbe..b4b3400 100644
--- a/arch/arm64/include/asm/arch_timer.h
+++ b/arch/arm64/include/asm/arch_timer.h
@@ -29,41 +29,29 @@
 
 #include <clocksource/arm_arch_timer.h>
 
-#if IS_ENABLED(CONFIG_FSL_ERRATUM_A008585)
+#if IS_ENABLED(CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND)
 extern struct static_key_false arch_timer_read_ool_enabled;
-#define needs_fsl_a008585_workaround() \
+#define needs_unstable_timer_counter_workaround() \
 	static_branch_unlikely(&arch_timer_read_ool_enabled)
 #else
-#define needs_fsl_a008585_workaround()  false
+#define needs_unstable_timer_counter_workaround()  false
 #endif
 
-u32 __fsl_a008585_read_cntp_tval_el0(void);
-u32 __fsl_a008585_read_cntv_tval_el0(void);
-u64 __fsl_a008585_read_cntvct_el0(void);
 
-/*
- * The number of retries is an arbitrary value well beyond the highest number
- * of iterations the loop has been observed to take.
- */
-#define __fsl_a008585_read_reg(reg) ({			\
-	u64 _old, _new;					\
-	int _retries = 200;				\
-							\
-	do {						\
-		_old = read_sysreg(reg);		\
-		_new = read_sysreg(reg);		\
-		_retries--;				\
-	} while (unlikely(_old != _new) && _retries);	\
-							\
-	WARN_ON_ONCE(!_retries);			\
-	_new;						\
-})
+struct arch_timer_erratum_workaround {
+	const char *id;		/* Indicate the Erratum ID */
+	u32 (*read_cntp_tval_el0)(void);
+	u32 (*read_cntv_tval_el0)(void);
+	u64 (*read_cntvct_el0)(void);
+};
+
+extern const struct arch_timer_erratum_workaround *timer_unstable_counter_workaround;
 
 #define arch_timer_reg_read_stable(reg) 		\
 ({							\
 	u64 _val;					\
-	if (needs_fsl_a008585_workaround())		\
-		_val = __fsl_a008585_read_##reg();	\
+	if (needs_unstable_timer_counter_workaround())		\
+		_val = timer_unstable_counter_workaround->read_##reg();\
 	else						\
 		_val = read_sysreg(reg);		\
 	_val;						\
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 4002d6d..1945af2 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -342,10 +342,14 @@ config ARM_ARCH_TIMER_EVTSTREAM
 	  This must be disabled for hardware validation purposes to detect any
 	  hardware anomalies of missing events.
 
+config ARM_ARCH_TIMER_OOL_WORKAROUND
+	bool
+
 config FSL_ERRATUM_A008585
 	bool "Workaround for Freescale/NXP Erratum A-008585"
 	default y
 	depends on ARM_ARCH_TIMER && ARM64
+	select ARM_ARCH_TIMER_OOL_WORKAROUND
 	help
 	  This option enables a workaround for Freescale/NXP Erratum
 	  A-008585 ("ARM generic timer may contain an erroneous
diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 6a9d031..2af0739 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -96,27 +96,58 @@ early_param("clocksource.arm_arch_timer.evtstrm", early_evtstrm_cfg);
  */
 
 #ifdef CONFIG_FSL_ERRATUM_A008585
-DEFINE_STATIC_KEY_FALSE(arch_timer_read_ool_enabled);
-EXPORT_SYMBOL_GPL(arch_timer_read_ool_enabled);
-
-static int fsl_a008585_enable = -1;
-
-u32 __fsl_a008585_read_cntp_tval_el0(void)
+/*
+ * The number of retries is an arbitrary value well beyond the highest number
+ * of iterations the loop has been observed to take.
+ */
+#define __fsl_a008585_read_reg(reg) ({			\
+	u64 _old, _new;					\
+	int _retries = 200;				\
+							\
+	do {						\
+		_old = read_sysreg(reg);		\
+		_new = read_sysreg(reg);		\
+		_retries--;				\
+	} while (unlikely(_old != _new) && _retries);	\
+							\
+	WARN_ON_ONCE(!_retries);			\
+	_new;						\
+})
+
+static u32 notrace fsl_a008585_read_cntp_tval_el0(void)
 {
 	return __fsl_a008585_read_reg(cntp_tval_el0);
 }
 
-u32 __fsl_a008585_read_cntv_tval_el0(void)
+static u32 notrace fsl_a008585_read_cntv_tval_el0(void)
 {
 	return __fsl_a008585_read_reg(cntv_tval_el0);
 }
 
-u64 __fsl_a008585_read_cntvct_el0(void)
+static u64 notrace fsl_a008585_read_cntvct_el0(void)
 {
 	return __fsl_a008585_read_reg(cntvct_el0);
 }
-EXPORT_SYMBOL(__fsl_a008585_read_cntvct_el0);
-#endif /* CONFIG_FSL_ERRATUM_A008585 */
+#endif
+
+#ifdef CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND
+const struct arch_timer_erratum_workaround *timer_unstable_counter_workaround = NULL;
+EXPORT_SYMBOL_GPL(timer_unstable_counter_workaround);
+
+DEFINE_STATIC_KEY_FALSE(arch_timer_read_ool_enabled);
+EXPORT_SYMBOL_GPL(arch_timer_read_ool_enabled);
+
+static const struct arch_timer_erratum_workaround ool_workarounds[] = {
+#ifdef CONFIG_FSL_ERRATUM_A008585
+	{
+		.id = "fsl,erratum-a008585",
+		.read_cntp_tval_el0 = fsl_a008585_read_cntp_tval_el0,
+		.read_cntv_tval_el0 = fsl_a008585_read_cntv_tval_el0,
+		.read_cntvct_el0 = fsl_a008585_read_cntvct_el0,
+	},
+#endif
+};
+#endif /* CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND */
 
 static __always_inline
 void arch_timer_reg_write(int access, enum arch_timer_reg reg, u32 val,
@@ -267,8 +298,8 @@ static __always_inline void set_next_event(const int access, unsigned long evt,
 	arch_timer_reg_write(access, ARCH_TIMER_REG_CTRL, ctrl, clk);
 }
 
-#ifdef CONFIG_FSL_ERRATUM_A008585
-static __always_inline void fsl_a008585_set_next_event(const int access,
+#ifdef CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND
+static __always_inline void erratum_set_next_event_generic(const int access,
 		unsigned long evt, struct clock_event_device *clk)
 {
 	unsigned long ctrl;
@@ -286,20 +317,20 @@ static __always_inline void fsl_a008585_set_next_event(const int access,
 	arch_timer_reg_write(access, ARCH_TIMER_REG_CTRL, ctrl, clk);
 }
 
-static int fsl_a008585_set_next_event_virt(unsigned long evt,
+static int erratum_set_next_event_virt(unsigned long evt,
 					   struct clock_event_device *clk)
 {
-	fsl_a008585_set_next_event(ARCH_TIMER_VIRT_ACCESS, evt, clk);
+	erratum_set_next_event_generic(ARCH_TIMER_VIRT_ACCESS, evt, clk);
 	return 0;
 }
 
-static int fsl_a008585_set_next_event_phys(unsigned long evt,
+static int erratum_set_next_event_phys(unsigned long evt,
 					   struct clock_event_device *clk)
 {
-	fsl_a008585_set_next_event(ARCH_TIMER_PHYS_ACCESS, evt, clk);
+	erratum_set_next_event_generic(ARCH_TIMER_PHYS_ACCESS, evt, clk);
 	return 0;
 }
-#endif /* CONFIG_FSL_ERRATUM_A008585 */
+#endif /* CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND */
 
 static int arch_timer_set_next_event_virt(unsigned long evt,
 					  struct clock_event_device *clk)
@@ -329,16 +360,16 @@ static int arch_timer_set_next_event_phys_mem(unsigned long evt,
 	return 0;
 }
 
-static void fsl_a008585_set_sne(struct clock_event_device *clk)
+static void erratum_workaround_set_sne(struct clock_event_device *clk)
 {
-#ifdef CONFIG_FSL_ERRATUM_A008585
+#ifdef CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND
 	if (!static_branch_unlikely(&arch_timer_read_ool_enabled))
 		return;
 
 	if (arch_timer_uses_ppi == VIRT_PPI)
-		clk->set_next_event = fsl_a008585_set_next_event_virt;
+		clk->set_next_event = erratum_set_next_event_virt;
 	else
-		clk->set_next_event = fsl_a008585_set_next_event_phys;
+		clk->set_next_event = erratum_set_next_event_phys;
 #endif
 }
 
@@ -371,7 +402,7 @@ static void __arch_timer_setup(unsigned type,
 			BUG();
 		}
 
-		fsl_a008585_set_sne(clk);
+		erratum_workaround_set_sne(clk);
 	} else {
 		clk->features |= CLOCK_EVT_FEAT_DYNIRQ;
 		clk->name = "arch_mem_timer";
@@ -591,7 +622,7 @@ static void __init arch_counter_register(unsigned type)
 
 		clocksource_counter.archdata.vdso_direct = true;
 
-#ifdef CONFIG_FSL_ERRATUM_A008585
+#ifdef CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND
 		/*
 		 * Don't use the vdso fastpath if errata require using
 		 * the out-of-line counter accessor.
@@ -879,12 +910,15 @@ static int __init arch_timer_of_init(struct device_node *np)
 
 	arch_timer_c3stop = !of_property_read_bool(np, "always-on");
 
-#ifdef CONFIG_FSL_ERRATUM_A008585
-	if (fsl_a008585_enable < 0)
-		fsl_a008585_enable = of_property_read_bool(np, "fsl,erratum-a008585");
-	if (fsl_a008585_enable) {
-		static_branch_enable(&arch_timer_read_ool_enabled);
-		pr_info("Enabling workaround for FSL erratum A-008585\n");
+#ifdef CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND
+	for (i = 0; i < ARRAY_SIZE(ool_workarounds); i++) {
+		if (of_property_read_bool(np, ool_workarounds[i].id)) {
+			timer_unstable_counter_workaround = &ool_workarounds[i];
+			static_branch_enable(&arch_timer_read_ool_enabled);
+			pr_info("arch_timer: Enabling workaround for %s\n",
+				timer_unstable_counter_workaround->id);
+			break;
+		}
 	}
 #endif
 
-- 
2.7.4

[PATCH 10/10] clocksource/drivers/arm_arch_timer: Work around Hisilicon erratum 161010101

[Daniel Lezcano]

From: Ding Tianhong <dingtianhong@huawei.com>

Erratum Hisilicon-161010101 says that the ARM generic timer counter "has
the potential to contain an erroneous value when the timer value
changes". Accesses to TVAL (both read and write) are also affected due
to the implicit counter read. Accesses to CVAL are not affected.

The workaround is to reread the system count registers until the value
of the second read is larger than the first one by less than 32, the
system counter can be guaranteed not to return wrong value twice by
back-to-back read and the error value is always larger than the correct
one by 32. Writes to TVAL are replaced with an equivalent write to CVAL.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, fix Kconfig, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
---
 drivers/clocksource/Kconfig          | 10 ++++++++
 drivers/clocksource/arm_arch_timer.c | 49 ++++++++++++++++++++++++++++++++++++
 2 files changed, 59 insertions(+)

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 1945af2..3356ab8 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -356,6 +356,16 @@ config FSL_ERRATUM_A008585
 	  value").  The workaround will only be active if the
 	  fsl,erratum-a008585 property is found in the timer node.
 
+config HISILICON_ERRATUM_161010101
+	bool "Workaround for Hisilicon Erratum 161010101"
+	default y
+	select ARM_ARCH_TIMER_OOL_WORKAROUND
+	depends on ARM_ARCH_TIMER && ARM64
+	help
+	  This option enables a workaround for Hisilicon Erratum
+	  161010101. The workaround will be active if the hisilicon,erratum-161010101
+	  property is found in the timer node.
+
 config ARM_GLOBAL_TIMER
 	bool "Support for the ARM global timer" if COMPILE_TEST
 	select CLKSRC_OF if OF
diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 2af0739..7b06aef 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -130,6 +130,47 @@ static u64 notrace fsl_a008585_read_cntvct_el0(void)
 }
 #endif
 
+#ifdef CONFIG_HISILICON_ERRATUM_161010101
+/*
+ * Verify whether the value of the second read is larger than the first by
+ * less than 32 is the only way to confirm the value is correct, so clear the
+ * lower 5 bits to check whether the difference is greater than 32 or not.
+ * Theoretically the erratum should not occur more than twice in succession
+ * when reading the system counter, but it is possible that some interrupts
+ * may lead to more than twice read errors, triggering the warning, so setting
+ * the number of retries far beyond the number of iterations the loop has been
+ * observed to take.
+ */
+#define __hisi_161010101_read_reg(reg) ({				\
+	u64 _old, _new;						\
+	int _retries = 50;					\
+								\
+	do {							\
+		_old = read_sysreg(reg);			\
+		_new = read_sysreg(reg);			\
+		_retries--;					\
+	} while (unlikely((_new - _old) >> 5) && _retries);	\
+								\
+	WARN_ON_ONCE(!_retries);				\
+	_new;							\
+})
+
+static u32 notrace hisi_161010101_read_cntp_tval_el0(void)
+{
+	return __hisi_161010101_read_reg(cntp_tval_el0);
+}
+
+static u32 notrace hisi_161010101_read_cntv_tval_el0(void)
+{
+	return __hisi_161010101_read_reg(cntv_tval_el0);
+}
+
+static u64 notrace hisi_161010101_read_cntvct_el0(void)
+{
+	return __hisi_161010101_read_reg(cntvct_el0);
+}
+#endif
+
 #ifdef CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND
 const struct arch_timer_erratum_workaround *timer_unstable_counter_workaround = NULL;
 EXPORT_SYMBOL_GPL(timer_unstable_counter_workaround);
@@ -146,6 +187,14 @@ static const struct arch_timer_erratum_workaround ool_workarounds[] = {
 		.read_cntvct_el0 = fsl_a008585_read_cntvct_el0,
 	},
 #endif
+#ifdef CONFIG_HISILICON_ERRATUM_161010101
+	{
+		.id = "hisilicon,erratum-161010101",
+		.read_cntp_tval_el0 = hisi_161010101_read_cntp_tval_el0,
+		.read_cntv_tval_el0 = hisi_161010101_read_cntv_tval_el0,
+		.read_cntvct_el0 = hisi_161010101_read_cntvct_el0,
+	},
+#endif
 };
 #endif /* CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND */
 
-- 
2.7.4