[PATCH v2] arm64: dts: ls1088a: Add TMU device tree support

Yuantian Tang
2017-05-12T04:33:16Z

Add nodes and properties for thermal management support.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
---
v2:
- put tmu node in ip block address order

arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 88 ++++++++++++++++++++++++++
1 file changed, 88 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index caecd14..c4109fb 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -44,6 +44,7 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>

/ {
compatible = "fsl,ls1088a";
@@ -61,6 +62,7 @@
compatible = "arm,cortex-a53";
reg = <0x0>;
clocks = <&clockgen 1 0>;
+ #cooling-cells = <2>;
};

cpu1: cpu at 1 {
@@ -89,6 +91,7 @@
compatible = "arm,cortex-a53";
reg = <0x100>;
clocks = <&clockgen 1 1>;
+ #cooling-cells = <2>;
};

cpu5: cpu at 101 {
@@ -153,6 +156,91 @@
clocks = <&sysclk>;
};

+ tmu: tmu at 1f80000 {
+ compatible = "fsl,qoriq-tmu";
+ reg = <0x0 0x1f80000 0x0 0x10000>;
+ interrupts = <0 23 0x4>;
+ fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+ fsl,tmu-calibration =
+ /* Calibration data group 1 */
+ <0x00000000 0x00000026
+ 0x00000001 0x0000002d
+ 0x00000002 0x00000032
+ 0x00000003 0x00000039
+ 0x00000004 0x0000003f
+ 0x00000005 0x00000046
+ 0x00000006 0x0000004d
+ 0x00000007 0x00000054
+ 0x00000008 0x0000005a
+ 0x00000009 0x00000061
+ 0x0000000a 0x0000006a
+ 0x0000000b 0x00000071
+ /* Calibration data group 2 */
+ 0x00010000 0x00000025
+ 0x00010001 0x0000002c
+ 0x00010002 0x00000035
+ 0x00010003 0x0000003d
+ 0x00010004 0x00000045
+ 0x00010005 0x0000004e
+ 0x00010006 0x00000057
+ 0x00010007 0x00000061
+ 0x00010008 0x0000006b
+ 0x00010009 0x00000076
+ /* Calibration data group 3 */
+ 0x00020000 0x00000029
+ 0x00020001 0x00000033
+ 0x00020002 0x0000003d
+ 0x00020003 0x00000049
+ 0x00020004 0x00000056
+ 0x00020005 0x00000061
+ 0x00020006 0x0000006d
+ /* Calibration data group 4 */
+ 0x00030000 0x00000021
+ 0x00030001 0x0000002a
+ 0x00030002 0x0000003c
+ 0x00030003 0x0000004e>;
+ little-endian;
+ #thermal-sensor-cells = <1>;
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <1000>;
+ polling-delay = <5000>;
+ thermal-sensors = <&tmu 0>;
+
+ trips {
+ cpu_alert: cpu-alert {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit: cpu-crit {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert>;
+ cooling-device =
+ <&cpu0 THERMAL_NO_LIMIT
+ THERMAL_NO_LIMIT>;
+ };
+
+ map1 {
+ trip = <&cpu_alert>;
+ cooling-device =
+ <&cpu4 THERMAL_NO_LIMIT
+ THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
+
duart0: serial at 21c0500 {
compatible = "fsl,ns16550", "ns16550a";
reg = <0x0 0x21c0500 0x0 0x100>;
--
2.1.0.27.g96db324