From: anup.patel@broadcom.com (Anup Patel)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v6 06/11] arm64: dts: Add NAND DT nodes for Stingray SOC
Date: Fri, 2 Jun 2017 12:04:30 +0530 [thread overview]
Message-ID: <1496385275-6899-7-git-send-email-anup.patel@broadcom.com> (raw)
In-Reply-To: <1496385275-6899-1-git-send-email-anup.patel@broadcom.com>
From: Pramod Kumar <pramod.kumar@broadcom.com>
This patch adds NAND controller DT Node and NAND chip DT
node for Stingray SOC and Stingray reference boards.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
---
arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi | 15 +++++++++++++++
arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi | 13 +++++++++++++
2 files changed, 28 insertions(+)
diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
index 992944b..aad45a2 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
@@ -53,3 +53,18 @@
&uart1 {
status = "okay";
};
+
+&nand {
+ status = "ok";
+ nandcs at 0 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <16>;
+ brcm,nand-oob-sector-size = <16>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 722e362..e8faa62 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -307,5 +307,18 @@
compatible = "brcm,iproc-rng200";
reg = <0x00220000 0x28>;
};
+
+ nand: nand at 00360000 {
+ compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
+ reg = <0x00360000 0x600>,
+ <0x0050a408 0x600>,
+ <0x00360f00 0x20>;
+ reg-names = "nand", "iproc-idm", "iproc-ext";
+ interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ brcm,nand-has-wp;
+ status = "disabled";
+ };
};
};
--
2.7.4
next prev parent reply other threads:[~2017-06-02 6:34 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-02 6:34 [PATCH v6 00/11] Broadcom Stingray SOC Initial Support Anup Patel
2017-06-02 6:34 ` [PATCH v6 01/11] dt-bindings: bcm: Add Broadcom Stingray bindings document Anup Patel
2017-06-02 6:34 ` [PATCH v6 02/11] dt-bindings: clk: Extend binding doc for Stingray SOC Anup Patel
2017-06-02 6:34 ` [PATCH v6 03/11] clk: bcm: Add clocks " Anup Patel
2017-06-02 22:10 ` Stephen Boyd
2017-06-06 4:21 ` Anup Patel
2017-06-02 6:34 ` [PATCH v6 04/11] arm64: dts: Initial DTS files for Broadcom " Anup Patel
2017-06-02 6:34 ` [PATCH v6 05/11] arm64: dts: Add clock DT nodes for " Anup Patel
2017-06-02 6:34 ` Anup Patel [this message]
2017-06-02 6:34 ` [PATCH v6 07/11] arm64: dts: Add pinctrl " Anup Patel
2017-06-02 6:34 ` [PATCH v6 08/11] arm64: dts: Add GPIO " Anup Patel
2017-06-02 6:34 ` [PATCH v6 09/11] arm64: dts: Add I2C DT nodes for Stingray SoC Anup Patel
2017-06-02 6:34 ` [PATCH v6 10/11] arm64: dts: Add PL022, PL330 and SP805 DT nodes for Stingray Anup Patel
2017-06-02 6:34 ` [PATCH v6 11/11] arm64: dts: Add PWM and SDHCI DT nodes for Stingray SOC Anup Patel
2017-06-05 16:51 ` [PATCH v6 00/11] Broadcom Stingray SOC Initial Support Florian Fainelli
2017-06-06 2:08 ` Florian Fainelli
2017-06-06 3:20 ` Anup Patel
2017-06-06 22:30 ` Stephen Boyd
2017-06-20 0:28 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1496385275-6899-7-git-send-email-anup.patel@broadcom.com \
--to=anup.patel@broadcom.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).