[PATCH v4 0/2] Add SMI LARBs reset for MediaTek MT8188 SoC

[PATCH v4 0/2] Add SMI LARBs reset for MediaTek MT8188 SoC

[Friday Yang]

Based on tag: next-20250220, linux-next/master

On the MediaTek MT8188 SoC platform, we encountered power-off failures
and SMI bus hang issues during camera stress tests. The issue arises
because bus glitches are sometimes produced when MTCMOS powers on or
off. While this is fairly normal, the software must handle these
glitches to avoid mistaking them for transaction signals. What's
more, this issue emerged only after the initial upstreaming of this
binding.

The software solutions can be summarized as follows:

1. Use CLAMP to disable the SMI sub-common port after turning off the
   LARB CG and before turning off the LARB MTCMOS.
2. Use CLAMP to disable/enable the SMI sub-common port.
3. Implement an AXI reset for SMI LARBs.

This patch primarily provides the implementation of an AXI reset.

Changes v4:
- Modify the commit message

v3:
https://lore.kernel.org/lkml/20250121065045.13514-2
-friday.yang@mediatek.com/
https://lore.kernel.org/lkml/20250121065045.13514-3
-friday.yang@mediatek.com/

Friday Yang (2):
  dt-bindings: clock: mediatek: Add SMI LARBs reset for MT8188
  clk: mediatek: Add SMI LARBs reset for MT8188

 .../bindings/clock/mediatek,mt8188-clock.yaml | 21 +++++++++++++++++++
 drivers/clk/mediatek/clk-mt8188-cam.c         | 17 +++++++++++++++
 drivers/clk/mediatek/clk-mt8188-img.c         | 18 ++++++++++++++++
 drivers/clk/mediatek/clk-mt8188-ipe.c         | 14 +++++++++++++
 4 files changed, 70 insertions(+)

--
2.46.0

[PATCH v4 1/2] dt-bindings: clock: mediatek: Add SMI LARBs reset for MT8188

[Friday Yang]

On the MediaTek platform, some SMI LARBs are directly connected to
the SMI Common, while others are connected to the SMI Sub-Common,
which in turn is connected to the SMI Common. The hardware block
diagram can be described as follows.

             SMI-Common(Smart Multimedia Interface Common)
                 |
         +----------------+------------------+
         |                |                  |
         |                |                  |
         |                |                  |
         |                |                  |
         |                |                  |
       larb0       SMI-Sub-Common0     SMI-Sub-Common1
                   |      |     |      |             |
                  larb1  larb2 larb3  larb7       larb9

For previous discussion on the direction of the code modifications,
please refer to:
https://lore.kernel.org/all/CAFGrd9qZhObQXvm2_abqaX83xMLqxjQETB2=
wXpobDWU1CnvkA@mail.gmail.com/
https://lore.kernel.org/all/CAPDyKFpokXV2gJDgowbixTvOH_5VL3B5H8ey
hP+KJ5Fasm2rFg@mail.gmail.com/

On the MediaTek MT8188 SoC platform, we encountered power-off failures
and SMI bus hang issues during camera stress tests. The issue arises
because bus glitches are sometimes produced when MTCMOS powers on or
off. While this is fairly normal, the software must handle these
glitches to avoid mistaking them for transaction signals. What's
more, this issue emerged only after the initial upstreaming of this
binding. Without these patches, the SMI becomes unstable during camera
stress tests.

The software solutions can be summarized as follows:

1. Use CLAMP to disable the SMI sub-common port after turning off the
   LARB CG and before turning off the LARB MTCMOS.
2. Use CLAMP to disable/enable the SMI sub-common port.
3. Implement an AXI reset for SMI LARBs.

This patch add '#reset-cells' for the clock controller located in image,
camera and IPE subsystems.

Signed-off-by: Friday Yang <friday.yang@mediatek.com>
---
 .../bindings/clock/mediatek,mt8188-clock.yaml | 21 +++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/Documentation/devicetree/bindings/clock/mediatek,mt8188-clock.yaml b/Documentation/devicetree/bindings/clock/mediatek,mt8188-clock.yaml
index 860570320545..2985c8c717d7 100644
--- a/Documentation/devicetree/bindings/clock/mediatek,mt8188-clock.yaml
+++ b/Documentation/devicetree/bindings/clock/mediatek,mt8188-clock.yaml
@@ -57,6 +57,27 @@ required:
   - reg
   - '#clock-cells'

+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - mediatek,mt8188-camsys-rawa
+              - mediatek,mt8188-camsys-rawb
+              - mediatek,mt8188-camsys-yuva
+              - mediatek,mt8188-camsys-yuvb
+              - mediatek,mt8188-imgsys-wpe1
+              - mediatek,mt8188-imgsys-wpe2
+              - mediatek,mt8188-imgsys-wpe3
+              - mediatek,mt8188-imgsys1-dip-nr
+              - mediatek,mt8188-imgsys1-dip-top
+              - mediatek,mt8188-ipesys
+
+    then:
+      required:
+        - '#reset-cells'
+
 additionalProperties: false

 examples:
--
2.46.0

Re: [PATCH v4 1/2] dt-bindings: clock: mediatek: Add SMI LARBs reset for MT8188

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 2213 bytes --]

On Fri, Feb 21, 2025 at 03:50:53PM +0800, Friday Yang wrote:
> On the MediaTek platform, some SMI LARBs are directly connected to
> the SMI Common, while others are connected to the SMI Sub-Common,
> which in turn is connected to the SMI Common. The hardware block
> diagram can be described as follows.
> 
>              SMI-Common(Smart Multimedia Interface Common)
>                  |
>          +----------------+------------------+
>          |                |                  |
>          |                |                  |
>          |                |                  |
>          |                |                  |
>          |                |                  |
>        larb0       SMI-Sub-Common0     SMI-Sub-Common1
>                    |      |     |      |             |
>                   larb1  larb2 larb3  larb7       larb9
> 
> For previous discussion on the direction of the code modifications,
> please refer to:
> https://lore.kernel.org/all/CAFGrd9qZhObQXvm2_abqaX83xMLqxjQETB2=
> wXpobDWU1CnvkA@mail.gmail.com/
> https://lore.kernel.org/all/CAPDyKFpokXV2gJDgowbixTvOH_5VL3B5H8ey
> hP+KJ5Fasm2rFg@mail.gmail.com/
> 
> On the MediaTek MT8188 SoC platform, we encountered power-off failures
> and SMI bus hang issues during camera stress tests. The issue arises
> because bus glitches are sometimes produced when MTCMOS powers on or
> off. While this is fairly normal, the software must handle these
> glitches to avoid mistaking them for transaction signals. What's
> more, this issue emerged only after the initial upstreaming of this
> binding. Without these patches, the SMI becomes unstable during camera
> stress tests.
> 
> The software solutions can be summarized as follows:
> 
> 1. Use CLAMP to disable the SMI sub-common port after turning off the
>    LARB CG and before turning off the LARB MTCMOS.
> 2. Use CLAMP to disable/enable the SMI sub-common port.
> 3. Implement an AXI reset for SMI LARBs.
> 
> This patch add '#reset-cells' for the clock controller located in image,
> camera and IPE subsystems.
> 
> Signed-off-by: Friday Yang <friday.yang@mediatek.com>

Acked-by: Conor Dooley <conor.dooley@microchip.com>

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v4 1/2] dt-bindings: clock: mediatek: Add SMI LARBs reset for MT8188

[AngeloGioacchino Del Regno]

Il 21/02/25 08:50, Friday Yang ha scritto:
> On the MediaTek platform, some SMI LARBs are directly connected to
> the SMI Common, while others are connected to the SMI Sub-Common,
> which in turn is connected to the SMI Common. The hardware block
> diagram can be described as follows.
> 
>               SMI-Common(Smart Multimedia Interface Common)
>                   |
>           +----------------+------------------+
>           |                |                  |
>           |                |                  |
>           |                |                  |
>           |                |                  |
>           |                |                  |
>         larb0       SMI-Sub-Common0     SMI-Sub-Common1
>                     |      |     |      |             |
>                    larb1  larb2 larb3  larb7       larb9
> 
> For previous discussion on the direction of the code modifications,
> please refer to:
> https://lore.kernel.org/all/CAFGrd9qZhObQXvm2_abqaX83xMLqxjQETB2=
> wXpobDWU1CnvkA@mail.gmail.com/
> https://lore.kernel.org/all/CAPDyKFpokXV2gJDgowbixTvOH_5VL3B5H8ey
> hP+KJ5Fasm2rFg@mail.gmail.com/
> 
> On the MediaTek MT8188 SoC platform, we encountered power-off failures
> and SMI bus hang issues during camera stress tests. The issue arises
> because bus glitches are sometimes produced when MTCMOS powers on or
> off. While this is fairly normal, the software must handle these
> glitches to avoid mistaking them for transaction signals. What's
> more, this issue emerged only after the initial upstreaming of this
> binding. Without these patches, the SMI becomes unstable during camera
> stress tests.
> 
> The software solutions can be summarized as follows:
> 
> 1. Use CLAMP to disable the SMI sub-common port after turning off the
>     LARB CG and before turning off the LARB MTCMOS.
> 2. Use CLAMP to disable/enable the SMI sub-common port.
> 3. Implement an AXI reset for SMI LARBs.
> 
> This patch add '#reset-cells' for the clock controller located in image,
> camera and IPE subsystems.
> 
> Signed-off-by: Friday Yang <friday.yang@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

> ---
>   .../bindings/clock/mediatek,mt8188-clock.yaml | 21 +++++++++++++++++++
>   1 file changed, 21 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/clock/mediatek,mt8188-clock.yaml b/Documentation/devicetree/bindings/clock/mediatek,mt8188-clock.yaml
> index 860570320545..2985c8c717d7 100644
> --- a/Documentation/devicetree/bindings/clock/mediatek,mt8188-clock.yaml
> +++ b/Documentation/devicetree/bindings/clock/mediatek,mt8188-clock.yaml
> @@ -57,6 +57,27 @@ required:
>     - reg
>     - '#clock-cells'
> 
> +allOf:
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - mediatek,mt8188-camsys-rawa
> +              - mediatek,mt8188-camsys-rawb
> +              - mediatek,mt8188-camsys-yuva
> +              - mediatek,mt8188-camsys-yuvb
> +              - mediatek,mt8188-imgsys-wpe1
> +              - mediatek,mt8188-imgsys-wpe2
> +              - mediatek,mt8188-imgsys-wpe3
> +              - mediatek,mt8188-imgsys1-dip-nr
> +              - mediatek,mt8188-imgsys1-dip-top
> +              - mediatek,mt8188-ipesys
> +
> +    then:
> +      required:
> +        - '#reset-cells'
> +
>   additionalProperties: false
> 
>   examples:
> --
> 2.46.0
> 


-- 
AngeloGioacchino Del Regno
Senior Software Engineer

Collabora Ltd.
Platinum Building, St John's Innovation Park, Cambridge CB4 0DS, UK
Registered in England & Wales, no. 5513718

Re: [PATCH v4 1/2] dt-bindings: clock: mediatek: Add SMI LARBs reset for MT8188

[Stephen Boyd]

Quoting Friday Yang (2025-02-20 23:50:53)
> On the MediaTek platform, some SMI LARBs are directly connected to
> the SMI Common, while others are connected to the SMI Sub-Common,
> which in turn is connected to the SMI Common. The hardware block
> diagram can be described as follows.
> 
>              SMI-Common(Smart Multimedia Interface Common)
>                  |
>          +----------------+------------------+

Applied to clk-next

[PATCH v4 2/2] clk: mediatek: Add SMI LARBs reset for MT8188

[Friday Yang]

SMI LARBs require reset functions when MTCMOS powers on or off.
Add reset platform data for SMI LARBs in the image, camera and IPE
subsystems.

Signed-off-by: Friday Yang <friday.yang@mediatek.com>
---
 drivers/clk/mediatek/clk-mt8188-cam.c | 17 +++++++++++++++++
 drivers/clk/mediatek/clk-mt8188-img.c | 18 ++++++++++++++++++
 drivers/clk/mediatek/clk-mt8188-ipe.c | 14 ++++++++++++++
 3 files changed, 49 insertions(+)

diff --git a/drivers/clk/mediatek/clk-mt8188-cam.c b/drivers/clk/mediatek/clk-mt8188-cam.c
index 7500bd25387f..9b029fdd584e 100644
--- a/drivers/clk/mediatek/clk-mt8188-cam.c
+++ b/drivers/clk/mediatek/clk-mt8188-cam.c
@@ -20,6 +20,8 @@ static const struct mtk_gate_regs cam_cg_regs = {
 #define GATE_CAM(_id, _name, _parent, _shift)			\
 	GATE_MTK(_id, _name, _parent, &cam_cg_regs, _shift, &mtk_clk_gate_ops_setclr)

+#define CAM_SYS_SMI_LARB_RST_OFF	(0xA0)
+
 static const struct mtk_gate cam_main_clks[] = {
 	GATE_CAM(CLK_CAM_MAIN_LARB13, "cam_main_larb13", "top_cam", 0),
 	GATE_CAM(CLK_CAM_MAIN_LARB14, "cam_main_larb14", "top_cam", 1),
@@ -72,6 +74,17 @@ static const struct mtk_gate cam_yuvb_clks[] = {
 	GATE_CAM(CLK_CAM_YUVB_CAMTG, "cam_yuvb_camtg", "top_cam", 2),
 };

+/* Reset for SMI larb 16a/16b/17a/17b */
+static u16 cam_sys_rst_ofs[] = {
+	CAM_SYS_SMI_LARB_RST_OFF,
+};
+
+static const struct mtk_clk_rst_desc cam_sys_rst_desc = {
+	.version = MTK_RST_SIMPLE,
+	.rst_bank_ofs = cam_sys_rst_ofs,
+	.rst_bank_nr = ARRAY_SIZE(cam_sys_rst_ofs),
+};
+
 static const struct mtk_clk_desc cam_main_desc = {
 	.clks = cam_main_clks,
 	.num_clks = ARRAY_SIZE(cam_main_clks),
@@ -80,21 +93,25 @@ static const struct mtk_clk_desc cam_main_desc = {
 static const struct mtk_clk_desc cam_rawa_desc = {
 	.clks = cam_rawa_clks,
 	.num_clks = ARRAY_SIZE(cam_rawa_clks),
+	.rst_desc = &cam_sys_rst_desc,
 };

 static const struct mtk_clk_desc cam_rawb_desc = {
 	.clks = cam_rawb_clks,
 	.num_clks = ARRAY_SIZE(cam_rawb_clks),
+	.rst_desc = &cam_sys_rst_desc,
 };

 static const struct mtk_clk_desc cam_yuva_desc = {
 	.clks = cam_yuva_clks,
 	.num_clks = ARRAY_SIZE(cam_yuva_clks),
+	.rst_desc = &cam_sys_rst_desc,
 };

 static const struct mtk_clk_desc cam_yuvb_desc = {
 	.clks = cam_yuvb_clks,
 	.num_clks = ARRAY_SIZE(cam_yuvb_clks),
+	.rst_desc = &cam_sys_rst_desc,
 };

 static const struct of_device_id of_match_clk_mt8188_cam[] = {
diff --git a/drivers/clk/mediatek/clk-mt8188-img.c b/drivers/clk/mediatek/clk-mt8188-img.c
index cb2fbd4136b9..d44bfbd8308a 100644
--- a/drivers/clk/mediatek/clk-mt8188-img.c
+++ b/drivers/clk/mediatek/clk-mt8188-img.c
@@ -20,6 +20,8 @@ static const struct mtk_gate_regs imgsys_cg_regs = {
 #define GATE_IMGSYS(_id, _name, _parent, _shift)			\
 	GATE_MTK(_id, _name, _parent, &imgsys_cg_regs, _shift, &mtk_clk_gate_ops_setclr)

+#define IMG_SYS_SMI_LARB_RST_OFF	(0xC)
+
 static const struct mtk_gate imgsys_main_clks[] = {
 	GATE_IMGSYS(CLK_IMGSYS_MAIN_LARB9, "imgsys_main_larb9", "top_img", 0),
 	GATE_IMGSYS(CLK_IMGSYS_MAIN_TRAW0, "imgsys_main_traw0", "top_img", 1),
@@ -58,6 +60,17 @@ static const struct mtk_gate imgsys1_dip_nr_clks[] = {
 	GATE_IMGSYS(CLK_IMGSYS1_DIP_NR_DIP_NR, "imgsys1_dip_nr_dip_nr", "top_img", 1),
 };

+/* Reset for SMI larb 10/11a/11b/11c/15 */
+static u16 img_sys_rst_ofs[] = {
+	IMG_SYS_SMI_LARB_RST_OFF,
+};
+
+static const struct mtk_clk_rst_desc img_sys_rst_desc = {
+	.version = MTK_RST_SIMPLE,
+	.rst_bank_ofs = img_sys_rst_ofs,
+	.rst_bank_nr = ARRAY_SIZE(img_sys_rst_ofs),
+};
+
 static const struct mtk_clk_desc imgsys_main_desc = {
 	.clks = imgsys_main_clks,
 	.num_clks = ARRAY_SIZE(imgsys_main_clks),
@@ -66,26 +79,31 @@ static const struct mtk_clk_desc imgsys_main_desc = {
 static const struct mtk_clk_desc imgsys_wpe1_desc = {
 	.clks = imgsys_wpe1_clks,
 	.num_clks = ARRAY_SIZE(imgsys_wpe1_clks),
+	.rst_desc = &img_sys_rst_desc,
 };

 static const struct mtk_clk_desc imgsys_wpe2_desc = {
 	.clks = imgsys_wpe2_clks,
 	.num_clks = ARRAY_SIZE(imgsys_wpe2_clks),
+	.rst_desc = &img_sys_rst_desc,
 };

 static const struct mtk_clk_desc imgsys_wpe3_desc = {
 	.clks = imgsys_wpe3_clks,
 	.num_clks = ARRAY_SIZE(imgsys_wpe3_clks),
+	.rst_desc = &img_sys_rst_desc,
 };

 static const struct mtk_clk_desc imgsys1_dip_top_desc = {
 	.clks = imgsys1_dip_top_clks,
 	.num_clks = ARRAY_SIZE(imgsys1_dip_top_clks),
+	.rst_desc = &img_sys_rst_desc,
 };

 static const struct mtk_clk_desc imgsys1_dip_nr_desc = {
 	.clks = imgsys1_dip_nr_clks,
 	.num_clks = ARRAY_SIZE(imgsys1_dip_nr_clks),
+	.rst_desc = &img_sys_rst_desc,
 };

 static const struct of_device_id of_match_clk_mt8188_imgsys_main[] = {
diff --git a/drivers/clk/mediatek/clk-mt8188-ipe.c b/drivers/clk/mediatek/clk-mt8188-ipe.c
index 8f1933b71e28..70a011c1f9ce 100644
--- a/drivers/clk/mediatek/clk-mt8188-ipe.c
+++ b/drivers/clk/mediatek/clk-mt8188-ipe.c
@@ -20,6 +20,8 @@ static const struct mtk_gate_regs ipe_cg_regs = {
 #define GATE_IPE(_id, _name, _parent, _shift)			\
 	GATE_MTK(_id, _name, _parent, &ipe_cg_regs, _shift, &mtk_clk_gate_ops_setclr)

+#define IPE_SYS_SMI_LARB_RST_OFF	(0xC)
+
 static const struct mtk_gate ipe_clks[] = {
 	GATE_IPE(CLK_IPE_DPE, "ipe_dpe", "top_ipe", 0),
 	GATE_IPE(CLK_IPE_FDVT, "ipe_fdvt", "top_ipe", 1),
@@ -28,9 +30,21 @@ static const struct mtk_gate ipe_clks[] = {
 	GATE_IPE(CLK_IPE_SMI_LARB12, "ipe_smi_larb12", "top_ipe", 4),
 };

+/* Reset for SMI larb 12 */
+static u16 ipe_sys_rst_ofs[] = {
+	IPE_SYS_SMI_LARB_RST_OFF,
+};
+
+static const struct mtk_clk_rst_desc ipe_sys_rst_desc = {
+	.version = MTK_RST_SIMPLE,
+	.rst_bank_ofs = ipe_sys_rst_ofs,
+	.rst_bank_nr = ARRAY_SIZE(ipe_sys_rst_ofs),
+};
+
 static const struct mtk_clk_desc ipe_desc = {
 	.clks = ipe_clks,
 	.num_clks = ARRAY_SIZE(ipe_clks),
+	.rst_desc = &ipe_sys_rst_desc,
 };

 static const struct of_device_id of_match_clk_mt8188_ipe[] = {
--
2.46.0

Re: [PATCH v4 2/2] clk: mediatek: Add SMI LARBs reset for MT8188

[AngeloGioacchino Del Regno]

Il 21/02/25 08:50, Friday Yang ha scritto:
> SMI LARBs require reset functions when MTCMOS powers on or off.
> Add reset platform data for SMI LARBs in the image, camera and IPE
> subsystems.
> 
> Signed-off-by: Friday Yang <friday.yang@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Re: [PATCH v4 2/2] clk: mediatek: Add SMI LARBs reset for MT8188

[Stephen Boyd]

Quoting Friday Yang (2025-02-20 23:50:54)
> SMI LARBs require reset functions when MTCMOS powers on or off.
> Add reset platform data for SMI LARBs in the image, camera and IPE
> subsystems.
> 
> Signed-off-by: Friday Yang <friday.yang@mediatek.com>
> ---

Applied to clk-next