From mboxrd@z Thu Jan  1 00:00:00 1970
From: david@lechnology.com (David Lechner)
Date: Tue,  1 Aug 2017 17:11:48 -0500
Subject: [PATCH v2 2/4] drm/tinydrm: add support for LEGO MINDSTORMS EV3 LCD
In-Reply-To: <1501625510-16727-1-git-send-email-david@lechnology.com>
References: <1501625510-16727-1-git-send-email-david@lechnology.com>
Message-ID: <1501625510-16727-3-git-send-email-david@lechnology.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

LEGO MINDSTORMS EV3 has an LCD with a ST7586 controller. This adds a new
module for the ST7586 controller with parameters for the EV3 LCD display.

Signed-off-by: David Lechner <david@lechnology.com>
---
 .../devicetree/bindings/display/st7586.txt         |  26 +
 drivers/gpu/drm/tinydrm/Kconfig                    |  10 +
 drivers/gpu/drm/tinydrm/Makefile                   |   1 +
 drivers/gpu/drm/tinydrm/st7586.c                   | 579 +++++++++++++++++++++
 include/drm/tinydrm/st7586.h                       |  34 ++
 5 files changed, 650 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/st7586.txt
 create mode 100644 drivers/gpu/drm/tinydrm/st7586.c
 create mode 100644 include/drm/tinydrm/st7586.h

diff --git a/Documentation/devicetree/bindings/display/st7586.txt b/Documentation/devicetree/bindings/display/st7586.txt
new file mode 100644
index 0000000..acf784aa
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/st7586.txt
@@ -0,0 +1,26 @@
+Sitronix ST7586 display panel
+
+Required properties:
+- compatible:	"lego,ev3-lcd".
+
+The node for this driver must be a child node of a SPI controller, hence
+all mandatory properties described in ../spi/spi-bus.txt must be specified.
+
+Optional properties:
+- dc-gpios:	D/C pin. The presence/absence of this GPIO determines
+		the panel interface mode (IM[3:0] pins):
+		- present: IM=x110 4-wire 8-bit data serial interface
+		- absent:  IM=x101 3-wire 9-bit data serial interface
+- reset-gpios:	Reset pin
+- power-supply:	A regulator node for the supply voltage.
+- backlight:	phandle of the backlight device attached to the panel
+- rotation:	panel rotation in degrees counter clockwise (0,90,180,270)
+
+Example:
+	display at 0{
+		compatible = "lego,ev3-lcd";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+		dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>;
+	};
diff --git a/drivers/gpu/drm/tinydrm/Kconfig b/drivers/gpu/drm/tinydrm/Kconfig
index f17c3ca..2e790e7 100644
--- a/drivers/gpu/drm/tinydrm/Kconfig
+++ b/drivers/gpu/drm/tinydrm/Kconfig
@@ -32,3 +32,13 @@ config TINYDRM_REPAPER
 	  2.71" TFT EPD Panel (E2271CS021)
 
 	  If M is selected the module will be called repaper.
+
+config TINYDRM_ST7586
+	tristate "DRM support for Sitronix ST7586 display panels"
+	depends on DRM_TINYDRM && SPI
+	select TINYDRM_MIPI_DBI
+	help
+	  DRM driver for the following Sitronix ST7586 panels:
+	  * LEGO MINDSTORMS EV3
+
+	  If M is selected the module will be called st7586.
diff --git a/drivers/gpu/drm/tinydrm/Makefile b/drivers/gpu/drm/tinydrm/Makefile
index 95bb4d4..0c184bd 100644
--- a/drivers/gpu/drm/tinydrm/Makefile
+++ b/drivers/gpu/drm/tinydrm/Makefile
@@ -6,3 +6,4 @@ obj-$(CONFIG_TINYDRM_MIPI_DBI)		+= mipi-dbi.o
 # Displays
 obj-$(CONFIG_TINYDRM_MI0283QT)		+= mi0283qt.o
 obj-$(CONFIG_TINYDRM_REPAPER)		+= repaper.o
+obj-$(CONFIG_TINYDRM_ST7586)		+= st7586.o
diff --git a/drivers/gpu/drm/tinydrm/st7586.c b/drivers/gpu/drm/tinydrm/st7586.c
new file mode 100644
index 0000000..6093021
--- /dev/null
+++ b/drivers/gpu/drm/tinydrm/st7586.c
@@ -0,0 +1,579 @@
+/*
+ * DRM driver for Sitronix ST7586 panels
+ *
+ * Copyright 2017 David Lechner <david@lechnology.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/dma-buf.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/property.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+#include <video/mipi_display.h>
+
+#include <drm/tinydrm/mipi-dbi.h>
+#include <drm/tinydrm/st7586.h>
+#include <drm/tinydrm/tinydrm-helpers.h>
+
+static inline u8 st7586_rgb565_to_gray2(u16 rgb)
+{
+	u8 r = (rgb & 0xf800) >> 11;
+	u8 g = (rgb & 0x07e0) >> 5;
+	u8 b = rgb & 0x001f;
+	/* ITU BT.601: Y = 0.299 R + 0.587 G + 0.114 B */
+	/* g is already * 2 because it is 6-bit */
+	u8 gray5 = (3 * r + 3 * g + b) / 10;
+
+	return gray5 >> 3;
+}
+
+static void st7586_from_rgb565(u8 *dst, void *vaddr,
+			       struct drm_framebuffer *fb,
+			       struct drm_clip_rect *clip)
+{
+	size_t len;
+	unsigned int x, y;
+	u16 *src, *buf;
+	u8 val;
+
+	/* 3 pixels per byte, so grow clip to nearest multiple of 3 */
+	clip->x1 = clip->x1 / 3 * 3;
+	clip->x2 = (clip->x2 + 2) / 3 * 3;
+	len = (clip->x2 - clip->x1) * sizeof(u16);
+
+	buf = kmalloc(len, GFP_KERNEL);
+	if (!buf)
+		return;
+
+	for (y = clip->y1; y < clip->y2; y++) {
+		src = vaddr + (y * fb->pitches[0]);
+		src += clip->x1;
+		memcpy(buf, src, len);
+		src = buf;
+		for (x = clip->x1; x < clip->x2; x += 3) {
+			val = st7586_rgb565_to_gray2(*src++) << 6;
+			if (val & 0xC0)
+				val |= 0x20;
+			val |= st7586_rgb565_to_gray2(*src++) << 3;
+			if (val & 0x18)
+				val |= 0x04;
+			val |= st7586_rgb565_to_gray2(*src++);
+			*dst++ = ~val;
+		}
+	}
+
+	/* now adjust the clip so it applies to dst */
+	clip->x1 /= 3;
+	clip->x2 /= 3;
+
+	kfree(buf);
+}
+
+static inline u8 st7586_xrgb8888_to_gray2(u32 rgb)
+{
+	u8 r = (rgb & 0x00ff0000) >> 16;
+	u8 g = (rgb & 0x0000ff00) >> 8;
+	u8 b = rgb & 0x000000ff;
+	/* ITU BT.601: Y = 0.299 R + 0.587 G + 0.114 B */
+	u8 gray8 = (3 * r + 6 * g + b) / 10;
+
+	return gray8 >> 6;
+}
+
+static void st7586_from_xrgb8888(u8 *dst, void *vaddr,
+				 struct drm_framebuffer *fb,
+				 struct drm_clip_rect *clip)
+{
+	size_t len;
+	unsigned int x, y;
+	u32 *src, *buf;
+	u8 val;
+
+	/* 3 pixels per byte, so grow clip to nearest multiple of 3 */
+	clip->x1 = clip->x1 / 3 * 3;
+	clip->x2 = (clip->x2 + 2) / 3 * 3;
+	len = (clip->x2 - clip->x1) * sizeof(u32);
+
+	buf = kmalloc(len, GFP_KERNEL);
+	if (!buf)
+		return;
+
+	for (y = clip->y1; y < clip->y2; y++) {
+		src = vaddr + (y * fb->pitches[0]);
+		src += clip->x1;
+		memcpy(buf, src, len);
+		src = buf;
+		for (x = clip->x1; x < clip->x2; x += 3) {
+			val = st7586_xrgb8888_to_gray2(*src++) << 6;
+			if (val & 0xC0)
+				val |= 0x20;
+			val |= st7586_xrgb8888_to_gray2(*src++) << 3;
+			if (val & 0x18)
+				val |= 0x04;
+			val |= st7586_xrgb8888_to_gray2(*src++);
+			*dst++ = ~val;
+		}
+	}
+
+	/* now adjust the clip so it applies to dst */
+	clip->x1 /= 3;
+	clip->x2 /= 3;
+
+	kfree(buf);
+}
+
+static int st7586_mipi_dbi_buf_copy(void *dst, struct drm_framebuffer *fb,
+				    struct drm_clip_rect *clip)
+{
+	struct drm_gem_cma_object *cma_obj = drm_fb_cma_get_gem_obj(fb, 0);
+	struct dma_buf_attachment *import_attach = cma_obj->base.import_attach;
+	struct drm_format_name_buf format_name;
+	void *src = cma_obj->vaddr;
+	int ret = 0;
+
+	if (import_attach) {
+		ret = dma_buf_begin_cpu_access(import_attach->dmabuf,
+					       DMA_FROM_DEVICE);
+		if (ret)
+			return ret;
+	}
+
+	switch (fb->format->format) {
+	case DRM_FORMAT_RGB565:
+		st7586_from_rgb565(dst, src, fb, clip);
+		break;
+	case DRM_FORMAT_XRGB8888:
+		st7586_from_xrgb8888(dst, src, fb, clip);
+		break;
+	default:
+		dev_err_once(fb->dev->dev, "Format is not supported: %s\n",
+			     drm_get_format_name(fb->format->format,
+						 &format_name));
+		ret = -EINVAL;
+		break;
+	}
+
+	if (import_attach)
+		ret = dma_buf_end_cpu_access(import_attach->dmabuf,
+					     DMA_FROM_DEVICE);
+	return ret;
+}
+
+static int st7586_mipi_dbi_fb_dirty(struct drm_framebuffer *fb,
+				    struct drm_file *file_priv,
+				    unsigned int flags, unsigned int color,
+				    struct drm_clip_rect *clips,
+				    unsigned int num_clips)
+{
+	struct tinydrm_device *tdev = fb->dev->dev_private;
+	struct mipi_dbi *mipi = mipi_dbi_from_tinydrm(tdev);
+	struct drm_clip_rect clip;
+	int ret = 0;
+
+	mutex_lock(&tdev->dirty_lock);
+
+	if (!mipi->enabled)
+		goto out_unlock;
+
+	/* fbdev can flush even when we're not interested */
+	if (tdev->pipe.plane.fb != fb)
+		goto out_unlock;
+
+	tinydrm_merge_clips(&clip, clips, num_clips, flags, fb->width,
+			    fb->height);
+
+	DRM_DEBUG("Flushing [FB:%d] x1=%u, x2=%u, y1=%u, y2=%u\n", fb->base.id,
+		  clip.x1, clip.x2, clip.y1, clip.y2);
+
+	ret = st7586_mipi_dbi_buf_copy(mipi->tx_buf, fb, &clip);
+	if (ret)
+		goto out_unlock;
+
+	/* NB: st7586_mipi_dbi_buf_copy() modifies clip */
+
+	mipi_dbi_command(mipi, MIPI_DCS_SET_COLUMN_ADDRESS,
+			 (clip.x1 >> 8) & 0xFF, clip.x1 & 0xFF,
+			 (clip.x2 >> 8) & 0xFF, (clip.x2 - 1) & 0xFF);
+	mipi_dbi_command(mipi, MIPI_DCS_SET_PAGE_ADDRESS,
+			 (clip.y1 >> 8) & 0xFF, clip.y1 & 0xFF,
+			 (clip.y2 >> 8) & 0xFF, (clip.y2 - 1) & 0xFF);
+
+	ret = mipi_dbi_command_buf(mipi, MIPI_DCS_WRITE_MEMORY_START,
+				   (u8 *)mipi->tx_buf,
+				   (clip.x2 - clip.x1) * (clip.y2 - clip.y1));
+
+out_unlock:
+	mutex_unlock(&tdev->dirty_lock);
+
+	if (ret)
+		dev_err_once(fb->dev->dev, "Failed to update display %d\n",
+			     ret);
+
+	return ret;
+}
+
+static const struct drm_framebuffer_funcs st7586_mipi_dbi_fb_funcs = {
+	.destroy	= drm_fb_cma_destroy,
+	.create_handle	= drm_fb_cma_create_handle,
+	.dirty		= st7586_mipi_dbi_fb_dirty,
+};
+
+void st7586_mipi_dbi_pipe_enable(struct drm_simple_display_pipe *pipe,
+				 struct drm_crtc_state *crtc_state)
+{
+	struct tinydrm_device *tdev = pipe_to_tinydrm(pipe);
+	struct mipi_dbi *mipi = mipi_dbi_from_tinydrm(tdev);
+	struct drm_framebuffer *fb = pipe->plane.fb;
+
+	DRM_DEBUG_KMS("\n");
+
+	mipi->enabled = true;
+	if (fb)
+		fb->funcs->dirty(fb, NULL, 0, 0, NULL, 0);
+
+	tinydrm_enable_backlight(mipi->backlight);
+}
+
+static void st7586_mipi_dbi_blank(struct mipi_dbi *mipi)
+{
+	struct drm_device *drm = mipi->tinydrm.drm;
+	u16 height = drm->mode_config.min_height;
+	u16 width = (drm->mode_config.min_width + 2) / 3;
+	size_t len = width * height;
+
+	memset(mipi->tx_buf, 0, len);
+
+	mipi_dbi_command(mipi, MIPI_DCS_SET_COLUMN_ADDRESS, 0, 0,
+			 (width >> 8) & 0xFF, (width - 1) & 0xFF);
+	mipi_dbi_command(mipi, MIPI_DCS_SET_PAGE_ADDRESS, 0, 0,
+			 (height >> 8) & 0xFF, (height - 1) & 0xFF);
+	mipi_dbi_command_buf(mipi, MIPI_DCS_WRITE_MEMORY_START,
+			     (u8 *)mipi->tx_buf, len);
+}
+
+static void st7586_mipi_dbi_pipe_disable(struct drm_simple_display_pipe *pipe)
+{
+	struct tinydrm_device *tdev = pipe_to_tinydrm(pipe);
+	struct mipi_dbi *mipi = mipi_dbi_from_tinydrm(tdev);
+
+	DRM_DEBUG_KMS("\n");
+
+	mipi->enabled = false;
+
+	if (mipi->backlight)
+		tinydrm_disable_backlight(mipi->backlight);
+	else
+		st7586_mipi_dbi_blank(mipi);
+}
+
+static const u32 st7586_mipi_dbi_formats[] = {
+	DRM_FORMAT_RGB565,
+	DRM_FORMAT_XRGB8888,
+};
+
+static int st7586_mipi_dbi_init(struct device *dev, struct mipi_dbi *mipi,
+		const struct drm_simple_display_pipe_funcs *pipe_funcs,
+		struct drm_driver *driver, const struct drm_display_mode *mode,
+		unsigned int rotation)
+{
+	size_t bufsize = (mode->vdisplay + 2) / 3 * mode->hdisplay;
+	struct tinydrm_device *tdev = &mipi->tinydrm;
+	int ret;
+
+	if (!mipi->command)
+		return -EINVAL;
+
+	mutex_init(&mipi->cmdlock);
+
+	mipi->tx_buf = devm_kmalloc(dev, bufsize, GFP_KERNEL);
+	if (!mipi->tx_buf)
+		return -ENOMEM;
+
+	ret = devm_tinydrm_init(dev, tdev, &st7586_mipi_dbi_fb_funcs, driver);
+	if (ret)
+		return ret;
+
+	ret = tinydrm_display_pipe_init(tdev, pipe_funcs,
+					DRM_MODE_CONNECTOR_VIRTUAL,
+					st7586_mipi_dbi_formats,
+					ARRAY_SIZE(st7586_mipi_dbi_formats),
+					mode, rotation);
+	if (ret)
+		return ret;
+
+	tdev->drm->mode_config.preferred_depth = 16;
+	mipi->rotation = rotation;
+
+	drm_mode_config_reset(tdev->drm);
+
+	DRM_DEBUG_KMS("preferred_depth=%u, rotation = %u\n",
+		      tdev->drm->mode_config.preferred_depth, rotation);
+
+	return 0;
+}
+
+static int st7586_init(struct mipi_dbi *mipi)
+{
+	struct tinydrm_device *tdev = &mipi->tinydrm;
+	struct device *dev = tdev->drm->dev;
+	u8 addr_mode;
+	int ret;
+
+	DRM_DEBUG_KMS("\n");
+
+	ret = regulator_enable(mipi->regulator);
+	if (ret) {
+		dev_err(dev, "Failed to enable regulator %d\n", ret);
+		return ret;
+	}
+
+	/* Avoid flicker by skipping setup if the bootloader has done it */
+	if (mipi_dbi_display_is_on(mipi))
+		return 0;
+
+	mipi_dbi_hw_reset(mipi);
+	ret = mipi_dbi_command(mipi, ST7586_AUTO_READ_CTRL, 0x9f);
+	if (ret) {
+		dev_err(dev, "Error sending command %d\n", ret);
+		regulator_disable(mipi->regulator);
+		return ret;
+	}
+
+	mipi_dbi_command(mipi, ST7586_OTP_RW_CTRL, 0x00);
+
+	msleep(10);
+
+	mipi_dbi_command(mipi, ST7586_OTP_READ);
+
+	msleep(20);
+
+	mipi_dbi_command(mipi, ST7586_OTP_CTRL_OUT);
+	mipi_dbi_command(mipi, MIPI_DCS_EXIT_SLEEP_MODE);
+	mipi_dbi_command(mipi, MIPI_DCS_SET_DISPLAY_OFF);
+
+	msleep(50);
+
+	mipi_dbi_command(mipi, ST7586_SET_VOP_OFFSET, 0x00);
+	mipi_dbi_command(mipi, ST7586_SET_VOP, 0xe3, 0x00);
+	mipi_dbi_command(mipi, ST7586_SET_BIAS_SYSTEM, 0x02);
+	mipi_dbi_command(mipi, ST7586_SET_BOOST_LEVEL, 0x04);
+	mipi_dbi_command(mipi, ST7586_ENABLE_ANALOG, 0x1d);
+	mipi_dbi_command(mipi, ST7586_SET_NLINE_INV, 0x00);
+	mipi_dbi_command(mipi, ST7586_DISP_MODE_GRAY);
+	mipi_dbi_command(mipi, ST7586_ENABLE_DDRAM, 0x02);
+
+	switch (mipi->rotation) {
+	default:
+		addr_mode = 0x00;
+		break;
+	case 90:
+		addr_mode = ST7586_DISP_CTRL_MY;
+		break;
+	case 180:
+		addr_mode = ST7586_DISP_CTRL_MX | ST7586_DISP_CTRL_MY;
+		break;
+	case 270:
+		addr_mode = ST7586_DISP_CTRL_MX;
+		break;
+	}
+	mipi_dbi_command(mipi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
+
+	mipi_dbi_command(mipi, ST7586_SET_DISP_DUTY, 0x7f);
+	mipi_dbi_command(mipi, ST7586_SET_PART_DISP, 0xa0);
+	mipi_dbi_command(mipi, MIPI_DCS_SET_PARTIAL_AREA, 0x00, 0x00, 0x00, 0x77);
+	mipi_dbi_command(mipi, MIPI_DCS_EXIT_INVERT_MODE);
+
+	msleep(100);
+
+	mipi_dbi_command(mipi, MIPI_DCS_SET_DISPLAY_ON);
+
+	return 0;
+}
+
+static void st7586_fini(void *data)
+{
+	struct mipi_dbi *mipi = data;
+
+	DRM_DEBUG_KMS("\n");
+	regulator_disable(mipi->regulator);
+}
+
+static const struct drm_simple_display_pipe_funcs st7586_pipe_funcs = {
+	.enable = st7586_mipi_dbi_pipe_enable,
+	.disable = st7586_mipi_dbi_pipe_disable,
+	.update = tinydrm_display_pipe_update,
+	.prepare_fb = tinydrm_display_pipe_prepare_fb,
+};
+
+static const struct drm_display_mode st7586_mode = {
+	TINYDRM_MODE(178, 128, 37, 27),
+};
+
+DEFINE_DRM_GEM_CMA_FOPS(st7586_fops);
+
+static struct drm_driver st7586_driver = {
+	.driver_features	= DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME |
+				  DRIVER_ATOMIC,
+	.fops			= &st7586_fops,
+	TINYDRM_GEM_DRIVER_OPS,
+	.lastclose		= tinydrm_lastclose,
+	.debugfs_init		= mipi_dbi_debugfs_init,
+	.name			= "st7586",
+	.desc			= "Sitronix ST7586",
+	.date			= "20170801",
+	.major			= 1,
+	.minor			= 0,
+};
+
+static const struct of_device_id st7586_of_match[] = {
+	{ .compatible = "lego,ev3-lcd" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, st7586_of_match);
+
+static const struct spi_device_id st7586_id[] = {
+	{ "ev3-lcd", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(spi, st7586_id);
+
+static int st7586_probe(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct tinydrm_device *tdev;
+	struct mipi_dbi *mipi;
+	struct gpio_desc *dc;
+	u32 rotation = 0;
+	int ret;
+
+	mipi = devm_kzalloc(dev, sizeof(*mipi), GFP_KERNEL);
+	if (!mipi)
+		return -ENOMEM;
+
+	mipi->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(mipi->reset)) {
+		dev_err(dev, "Failed to get gpio 'reset'\n");
+		return PTR_ERR(mipi->reset);
+	}
+
+	dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
+	if (IS_ERR(dc)) {
+		dev_err(dev, "Failed to get gpio 'dc'\n");
+		return PTR_ERR(dc);
+	}
+
+	mipi->regulator = devm_regulator_get(dev, "power");
+	if (IS_ERR(mipi->regulator))
+		return PTR_ERR(mipi->regulator);
+
+	mipi->backlight = tinydrm_of_find_backlight(dev);
+	if (IS_ERR(mipi->backlight))
+		return PTR_ERR(mipi->backlight);
+
+	device_property_read_u32(dev, "rotation", &rotation);
+
+	ret = mipi_dbi_spi_init(spi, mipi, dc);
+	if (ret)
+		return ret;
+
+	/*
+	 * we are using 8-bit data, so we are not actually swapping anything,
+	 * but setting mipi->swap_bytes makes mipi_dbi_typec3_command() do the
+	 * right thing and not use 16-bit transfers (which results in swapped
+	 * bytes on little-endian systems and causes out of order data to be
+	 * sent to the display).
+	 */
+	mipi->swap_bytes = true;
+
+	ret = st7586_mipi_dbi_init(&spi->dev, mipi, &st7586_pipe_funcs,
+				   &st7586_driver, &st7586_mode, rotation);
+	if (ret)
+		return ret;
+
+	ret = st7586_init(mipi);
+	if (ret)
+		return ret;
+
+	/* use devres to fini after drm unregister (drv->remove is before) */
+	ret = devm_add_action(dev, st7586_fini, mipi);
+	if (ret) {
+		st7586_fini(mipi);
+		return ret;
+	}
+
+	tdev = &mipi->tinydrm;
+
+	ret = devm_tinydrm_register(tdev);
+	if (ret)
+		return ret;
+
+	spi_set_drvdata(spi, mipi);
+
+	DRM_DEBUG_DRIVER("Initialized %s:%s @%uMHz on minor %d\n",
+			 tdev->drm->driver->name, dev_name(dev),
+			 spi->max_speed_hz / 1000000,
+			 tdev->drm->primary->index);
+
+	return 0;
+}
+
+static void st7586_shutdown(struct spi_device *spi)
+{
+	struct mipi_dbi *mipi = spi_get_drvdata(spi);
+
+	tinydrm_shutdown(&mipi->tinydrm);
+}
+
+static int __maybe_unused st7586_pm_suspend(struct device *dev)
+{
+	struct mipi_dbi *mipi = dev_get_drvdata(dev);
+	int ret;
+
+	ret = tinydrm_suspend(&mipi->tinydrm);
+	if (ret)
+		return ret;
+
+	st7586_fini(mipi);
+
+	return 0;
+}
+
+static int __maybe_unused st7586_pm_resume(struct device *dev)
+{
+	struct mipi_dbi *mipi = dev_get_drvdata(dev);
+	int ret;
+
+	ret = st7586_init(mipi);
+	if (ret)
+		return ret;
+
+	return tinydrm_resume(&mipi->tinydrm);
+}
+
+static const struct dev_pm_ops st7586_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(st7586_pm_suspend, st7586_pm_resume)
+};
+
+static struct spi_driver st7586_spi_driver = {
+	.driver = {
+		.name = "st7586",
+		.owner = THIS_MODULE,
+		.of_match_table = st7586_of_match,
+		.pm = &st7586_pm_ops,
+	},
+	.id_table = st7586_id,
+	.probe = st7586_probe,
+	.shutdown = st7586_shutdown,
+};
+module_spi_driver(st7586_spi_driver);
+
+MODULE_DESCRIPTION("Sitronix ST7586 DRM driver");
+MODULE_AUTHOR("David Lechner <david@lechnology.com>");
+MODULE_LICENSE("GPL");
diff --git a/include/drm/tinydrm/st7586.h b/include/drm/tinydrm/st7586.h
new file mode 100644
index 0000000..18fb56b
--- /dev/null
+++ b/include/drm/tinydrm/st7586.h
@@ -0,0 +1,34 @@
+/*
+ * ST7586 LCD controller
+ *
+ * Copyright (C) 2017 David Lechner <david@lechnology.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __LINUX_ST7856_H
+#define __LINUX_ST7856_H
+
+#define ST7586_DISP_MODE_GRAY	0x38
+#define ST7586_DISP_MODE_MONO	0x39
+#define ST7586_ENABLE_DDRAM	0x3a
+#define ST7586_SET_DISP_DUTY	0xb0
+#define ST7586_SET_PART_DISP	0xb4
+#define ST7586_SET_NLINE_INV	0xb5
+#define ST7586_SET_VOP		0xc0
+#define ST7586_SET_BIAS_SYSTEM	0xc3
+#define ST7586_SET_BOOST_LEVEL	0xc4
+#define ST7586_SET_VOP_OFFSET	0xc7
+#define ST7586_ENABLE_ANALOG	0xd0
+#define ST7586_AUTO_READ_CTRL	0xd7
+#define ST7586_OTP_RW_CTRL	0xe0
+#define ST7586_OTP_CTRL_OUT	0xe1
+#define ST7586_OTP_READ		0xe3
+
+#define ST7586_DISP_CTRL_MX	BIT(6)
+#define ST7586_DISP_CTRL_MY	BIT(7)
+
+#endif /* __LINUX_ST7856_H */
-- 
2.7.4