* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac @ 2017-11-07 2:49 Chris Zhong 2017-11-07 7:54 ` Vladimir Zapolskiy 0 siblings, 1 reply; 9+ messages in thread From: Chris Zhong @ 2017-11-07 2:49 UTC (permalink / raw) To: linux-arm-kernel The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by GPIO1_D6, this pin should be pull down then pull up to reset the phy. Add a phy-reset property in emac, make the phy can be reset when emac power on. Signed-off-by: Chris Zhong <zyw@rock-chips.com> --- arch/arm/boot/dts/rk3066a-rayeager.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rk3066a-rayeager.dts index 570157f..6064a0a 100644 --- a/arch/arm/boot/dts/rk3066a-rayeager.dts +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts @@ -173,6 +173,8 @@ pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; phy = <&phy0>; phy-supply = <&vcc_rmii>; + phy-reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>; /* PHY_RST */ + phy-reset-duration = <10>; /* millisecond */ status = "okay"; phy0: ethernet-phy at 0 { -- 2.7.4 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac 2017-11-07 2:49 [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac Chris Zhong @ 2017-11-07 7:54 ` Vladimir Zapolskiy 2017-11-07 9:51 ` Chris Zhong ` (2 more replies) 0 siblings, 3 replies; 9+ messages in thread From: Vladimir Zapolskiy @ 2017-11-07 7:54 UTC (permalink / raw) To: linux-arm-kernel Hello Chris, On 11/07/2017 04:49 AM, Chris Zhong wrote: > The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by > GPIO1_D6, this pin should be pull down then pull up to reset the phy. > Add a phy-reset property in emac, make the phy can be reset when emac > power on. for PHY reset there are properties 'reset-gpios' and 'reset-delay-us', please reference to Documentation/devicetree/bindings/net/mdio.txt Can you try to reuse them instead of adding new custom properties? As a side question, which is mainly addressed to Sergei and Roger, I don't quite understand why PHY properties were initially added to MAC/MDIO bus device tree nodes, in my opinion they must be moved under PHY device tree nodes. -- With best wishes, Vladimir > > Signed-off-by: Chris Zhong <zyw@rock-chips.com> > --- > > arch/arm/boot/dts/rk3066a-rayeager.dts | 2 ++ > 1 file changed, 2 insertions(+) > > diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rk3066a-rayeager.dts > index 570157f..6064a0a 100644 > --- a/arch/arm/boot/dts/rk3066a-rayeager.dts > +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts > @@ -173,6 +173,8 @@ > pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; > phy = <&phy0>; > phy-supply = <&vcc_rmii>; > + phy-reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>; /* PHY_RST */ > + phy-reset-duration = <10>; /* millisecond */ > status = "okay"; > > phy0: ethernet-phy at 0 { > ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac 2017-11-07 7:54 ` Vladimir Zapolskiy @ 2017-11-07 9:51 ` Chris Zhong 2017-11-07 18:26 ` Florian Fainelli 2017-11-07 15:59 ` Andrew Lunn 2017-11-09 8:20 ` Roger Quadros 2 siblings, 1 reply; 9+ messages in thread From: Chris Zhong @ 2017-11-07 9:51 UTC (permalink / raw) To: linux-arm-kernel On 2017?11?07? 15:54, Vladimir Zapolskiy wrote: > Hello Chris, > > On 11/07/2017 04:49 AM, Chris Zhong wrote: >> The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by >> GPIO1_D6, this pin should be pull down then pull up to reset the phy. >> Add a phy-reset property in emac, make the phy can be reset when emac >> power on. > for PHY reset there are properties 'reset-gpios' and 'reset-delay-us', > please reference to Documentation/devicetree/bindings/net/mdio.txt > > Can you try to reuse them instead of adding new custom properties? This phy-reset is from Documentation/devicetree/bindings/net/arc_emac.txt. And copy from arch/arm/boot/dts/rk3036-kylin.dts. Can we just use these properties, they are not new. > As a side question, which is mainly addressed to Sergei and Roger, > I don't quite understand why PHY properties were initially added to > MAC/MDIO bus device tree nodes, in my opinion they must be moved under > PHY device tree nodes. > > -- > With best wishes, > Vladimir > >> Signed-off-by: Chris Zhong <zyw@rock-chips.com> >> --- >> >> arch/arm/boot/dts/rk3066a-rayeager.dts | 2 ++ >> 1 file changed, 2 insertions(+) >> >> diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rk3066a-rayeager.dts >> index 570157f..6064a0a 100644 >> --- a/arch/arm/boot/dts/rk3066a-rayeager.dts >> +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts >> @@ -173,6 +173,8 @@ >> pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; >> phy = <&phy0>; >> phy-supply = <&vcc_rmii>; >> + phy-reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>; /* PHY_RST */ >> + phy-reset-duration = <10>; /* millisecond */ >> status = "okay"; >> >> phy0: ethernet-phy at 0 { >> > > -- Chris Zhong ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac 2017-11-07 9:51 ` Chris Zhong @ 2017-11-07 18:26 ` Florian Fainelli 2017-11-08 9:49 ` Chris Zhong 0 siblings, 1 reply; 9+ messages in thread From: Florian Fainelli @ 2017-11-07 18:26 UTC (permalink / raw) To: linux-arm-kernel On 11/07/2017 01:51 AM, Chris Zhong wrote: > > > On 2017?11?07? 15:54, Vladimir Zapolskiy wrote: >> Hello Chris, >> >> On 11/07/2017 04:49 AM, Chris Zhong wrote: >>> The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by >>> GPIO1_D6, this pin should be pull down then pull up to reset the phy. >>> Add a phy-reset property in emac, make the phy can be reset when emac >>> power on. >> for PHY reset there are properties 'reset-gpios' and 'reset-delay-us', >> please reference to Documentation/devicetree/bindings/net/mdio.txt >> >> Can you try to reuse them instead of adding new custom properties? > This phy-reset is from Documentation/devicetree/bindings/net/arc_emac.txt. > And copy from arch/arm/boot/dts/rk3036-kylin.dts. > Can we just use these properties, they are not new. Because it already exists does not mean it's correct, in fact, it is not at all because it places the reset property for a PHY into the MAC node, which is just not what this is, what we should be using instead is the following patch series: http://patchwork.ozlabs.org/project/netdev/list/?series=9267 http://patchwork.ozlabs.org/patch/828499/ http://patchwork.ozlabs.org/patch/828505/ http://patchwork.ozlabs.org/patch/828501/ http://patchwork.ozlabs.org/patch/828502/ >> As a side question, which is mainly addressed to Sergei and Roger, >> I don't quite understand why PHY properties were initially added to >> MAC/MDIO bus device tree nodes, in my opinion they must be moved under >> PHY device tree nodes. >> >> -- >> With best wishes, >> Vladimir >> >>> Signed-off-by: Chris Zhong <zyw@rock-chips.com> >>> --- >>> >>> arch/arm/boot/dts/rk3066a-rayeager.dts | 2 ++ >>> 1 file changed, 2 insertions(+) >>> >>> diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts >>> b/arch/arm/boot/dts/rk3066a-rayeager.dts >>> index 570157f..6064a0a 100644 >>> --- a/arch/arm/boot/dts/rk3066a-rayeager.dts >>> +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts >>> @@ -173,6 +173,8 @@ >>> pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; >>> phy = <&phy0>; >>> phy-supply = <&vcc_rmii>; >>> + phy-reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>; /* PHY_RST */ >>> + phy-reset-duration = <10>; /* millisecond */ >>> status = "okay"; >>> phy0: ethernet-phy at 0 { >>> >> >> > -- Florian ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac 2017-11-07 18:26 ` Florian Fainelli @ 2017-11-08 9:49 ` Chris Zhong 2017-11-09 8:28 ` Roger Quadros 0 siblings, 1 reply; 9+ messages in thread From: Chris Zhong @ 2017-11-08 9:49 UTC (permalink / raw) To: linux-arm-kernel Hi Florian Fainelli On 2017?11?08? 02:26, Florian Fainelli wrote: > On 11/07/2017 01:51 AM, Chris Zhong wrote: >> >> On 2017?11?07? 15:54, Vladimir Zapolskiy wrote: >>> Hello Chris, >>> >>> On 11/07/2017 04:49 AM, Chris Zhong wrote: >>>> The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by >>>> GPIO1_D6, this pin should be pull down then pull up to reset the phy. >>>> Add a phy-reset property in emac, make the phy can be reset when emac >>>> power on. >>> for PHY reset there are properties 'reset-gpios' and 'reset-delay-us', >>> please reference to Documentation/devicetree/bindings/net/mdio.txt >>> >>> Can you try to reuse them instead of adding new custom properties? >> This phy-reset is from Documentation/devicetree/bindings/net/arc_emac.txt. >> And copy from arch/arm/boot/dts/rk3036-kylin.dts. >> Can we just use these properties, they are not new. > Because it already exists does not mean it's correct, in fact, it is not > at all because it places the reset property for a PHY into the MAC node, > which is just not what this is, what we should be using instead is the > following patch series: > > http://patchwork.ozlabs.org/project/netdev/list/?series=9267 > > http://patchwork.ozlabs.org/patch/828499/ > http://patchwork.ozlabs.org/patch/828505/ > http://patchwork.ozlabs.org/patch/828501/ > http://patchwork.ozlabs.org/patch/828502/ Okay, this series works for me, and I will push a new version patch following it, with a reset-gpios property under phy node. And hope this series can be applied soon. Thanks Chris Zhong >>> As a side question, which is mainly addressed to Sergei and Roger, >>> I don't quite understand why PHY properties were initially added to >>> MAC/MDIO bus device tree nodes, in my opinion they must be moved under >>> PHY device tree nodes. >>> >>> -- >>> With best wishes, >>> Vladimir >>> >>>> Signed-off-by: Chris Zhong <zyw@rock-chips.com> >>>> --- >>>> >>>> arch/arm/boot/dts/rk3066a-rayeager.dts | 2 ++ >>>> 1 file changed, 2 insertions(+) >>>> >>>> diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts >>>> b/arch/arm/boot/dts/rk3066a-rayeager.dts >>>> index 570157f..6064a0a 100644 >>>> --- a/arch/arm/boot/dts/rk3066a-rayeager.dts >>>> +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts >>>> @@ -173,6 +173,8 @@ >>>> pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; >>>> phy = <&phy0>; >>>> phy-supply = <&vcc_rmii>; >>>> + phy-reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>; /* PHY_RST */ >>>> + phy-reset-duration = <10>; /* millisecond */ >>>> status = "okay"; >>>> phy0: ethernet-phy at 0 { >>>> >>> > ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac 2017-11-08 9:49 ` Chris Zhong @ 2017-11-09 8:28 ` Roger Quadros 2017-11-09 8:40 ` Roger Quadros 0 siblings, 1 reply; 9+ messages in thread From: Roger Quadros @ 2017-11-09 8:28 UTC (permalink / raw) To: linux-arm-kernel On 08/11/17 11:49, Chris Zhong wrote: > Hi Florian Fainelli > > > On 2017?11?08? 02:26, Florian Fainelli wrote: >> On 11/07/2017 01:51 AM, Chris Zhong wrote: >>> >>> On 2017?11?07? 15:54, Vladimir Zapolskiy wrote: >>>> Hello Chris, >>>> >>>> On 11/07/2017 04:49 AM, Chris Zhong wrote: >>>>> The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by >>>>> GPIO1_D6, this pin should be pull down then pull up to reset the phy. >>>>> Add a phy-reset property in emac, make the phy can be reset when emac >>>>> power on. >>>> for PHY reset there are properties 'reset-gpios' and 'reset-delay-us', >>>> please reference to Documentation/devicetree/bindings/net/mdio.txt >>>> >>>> Can you try to reuse them instead of adding new custom properties? >>> This phy-reset is from Documentation/devicetree/bindings/net/arc_emac.txt. >>> And copy from arch/arm/boot/dts/rk3036-kylin.dts. >>> Can we just use these properties, they are not new. >> Because it already exists does not mean it's correct, in fact, it is not >> at all because it places the reset property for a PHY into the MAC node, >> which is just not what this is, what we should be using instead is the >> following patch series: >> >> http://patchwork.ozlabs.org/project/netdev/list/?series=9267 >> >> http://patchwork.ozlabs.org/patch/828499/ >> http://patchwork.ozlabs.org/patch/828505/ >> http://patchwork.ozlabs.org/patch/828501/ >> http://patchwork.ozlabs.org/patch/828502/ > Okay, this series works for me, and I will push a new version patch following it, > with a reset-gpios property under phy node. > And hope this series can be applied soon. > If 'reset-gpios' and 'reset-delay-us' as per [1] works for you then why not use that? [1] Documentation/devicetree/bindings/net/mdio.txt > Thanks > Chris Zhong > > >>>> As a side question, which is mainly addressed to Sergei and Roger, >>>> I don't quite understand why PHY properties were initially added to >>>> MAC/MDIO bus device tree nodes, in my opinion they must be moved under >>>> PHY device tree nodes. >>>> >>>> --? >>>> With best wishes, >>>> Vladimir >>>> >>>>> Signed-off-by: Chris Zhong <zyw@rock-chips.com> >>>>> --- >>>>> >>>>> ?? arch/arm/boot/dts/rk3066a-rayeager.dts | 2 ++ >>>>> ?? 1 file changed, 2 insertions(+) >>>>> >>>>> diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts >>>>> b/arch/arm/boot/dts/rk3066a-rayeager.dts >>>>> index 570157f..6064a0a 100644 >>>>> --- a/arch/arm/boot/dts/rk3066a-rayeager.dts >>>>> +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts >>>>> @@ -173,6 +173,8 @@ >>>>> ?????? pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; >>>>> ?????? phy = <&phy0>; >>>>> ?????? phy-supply = <&vcc_rmii>; >>>>> +??? phy-reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>; /* PHY_RST */ >>>>> +??? phy-reset-duration = <10>; /* millisecond */ >>>>> ?????? status = "okay"; >>>>> ???????? phy0: ethernet-phy at 0 { >>>>> >>>> >> > -- cheers, -roger Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac 2017-11-09 8:28 ` Roger Quadros @ 2017-11-09 8:40 ` Roger Quadros 0 siblings, 0 replies; 9+ messages in thread From: Roger Quadros @ 2017-11-09 8:40 UTC (permalink / raw) To: linux-arm-kernel On 09/11/17 10:28, Roger Quadros wrote: > On 08/11/17 11:49, Chris Zhong wrote: >> Hi Florian Fainelli >> >> >> On 2017?11?08? 02:26, Florian Fainelli wrote: >>> On 11/07/2017 01:51 AM, Chris Zhong wrote: >>>> >>>> On 2017?11?07? 15:54, Vladimir Zapolskiy wrote: >>>>> Hello Chris, >>>>> >>>>> On 11/07/2017 04:49 AM, Chris Zhong wrote: >>>>>> The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by >>>>>> GPIO1_D6, this pin should be pull down then pull up to reset the phy. >>>>>> Add a phy-reset property in emac, make the phy can be reset when emac >>>>>> power on. >>>>> for PHY reset there are properties 'reset-gpios' and 'reset-delay-us', >>>>> please reference to Documentation/devicetree/bindings/net/mdio.txt >>>>> >>>>> Can you try to reuse them instead of adding new custom properties? >>>> This phy-reset is from Documentation/devicetree/bindings/net/arc_emac.txt. >>>> And copy from arch/arm/boot/dts/rk3036-kylin.dts. >>>> Can we just use these properties, they are not new. >>> Because it already exists does not mean it's correct, in fact, it is not >>> at all because it places the reset property for a PHY into the MAC node, >>> which is just not what this is, what we should be using instead is the >>> following patch series: >>> >>> http://patchwork.ozlabs.org/project/netdev/list/?series=9267 >>> >>> http://patchwork.ozlabs.org/patch/828499/ >>> http://patchwork.ozlabs.org/patch/828505/ >>> http://patchwork.ozlabs.org/patch/828501/ >>> http://patchwork.ozlabs.org/patch/828502/ >> Okay, this series works for me, and I will push a new version patch following it, >> with a reset-gpios property under phy node. >> And hope this series can be applied soon. >> > > If 'reset-gpios' and 'reset-delay-us' as per [1] works for you > then why not use that? > > [1] Documentation/devicetree/bindings/net/mdio.txt I take back my statement. You should use the above only if you have a single reset line connected to multiple PHYs on the same MDIO bus. In all other cases the reset properties should be part of PHY device node. However, we need to still ensure that the mdio_bus driver issues the reset. This piece is still missing in the code. > >> Thanks >> Chris Zhong >> >> >>>>> As a side question, which is mainly addressed to Sergei and Roger, >>>>> I don't quite understand why PHY properties were initially added to >>>>> MAC/MDIO bus device tree nodes, in my opinion they must be moved under >>>>> PHY device tree nodes. >>>>> >>>>> --? >>>>> With best wishes, >>>>> Vladimir >>>>> >>>>>> Signed-off-by: Chris Zhong <zyw@rock-chips.com> >>>>>> --- >>>>>> >>>>>> ?? arch/arm/boot/dts/rk3066a-rayeager.dts | 2 ++ >>>>>> ?? 1 file changed, 2 insertions(+) >>>>>> >>>>>> diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts >>>>>> b/arch/arm/boot/dts/rk3066a-rayeager.dts >>>>>> index 570157f..6064a0a 100644 >>>>>> --- a/arch/arm/boot/dts/rk3066a-rayeager.dts >>>>>> +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts >>>>>> @@ -173,6 +173,8 @@ >>>>>> ?????? pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; >>>>>> ?????? phy = <&phy0>; >>>>>> ?????? phy-supply = <&vcc_rmii>; >>>>>> +??? phy-reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>; /* PHY_RST */ >>>>>> +??? phy-reset-duration = <10>; /* millisecond */ >>>>>> ?????? status = "okay"; >>>>>> ???????? phy0: ethernet-phy at 0 { >>>>>> >>>>> >>> >> > -- cheers, -roger Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac 2017-11-07 7:54 ` Vladimir Zapolskiy 2017-11-07 9:51 ` Chris Zhong @ 2017-11-07 15:59 ` Andrew Lunn 2017-11-09 8:20 ` Roger Quadros 2 siblings, 0 replies; 9+ messages in thread From: Andrew Lunn @ 2017-11-07 15:59 UTC (permalink / raw) To: linux-arm-kernel > As a side question, which is mainly addressed to Sergei and Roger, > I don't quite understand why PHY properties were initially added to > MAC/MDIO bus device tree nodes, in my opinion they must be moved under > PHY device tree nodes. If you look at the implementation, they are not actually PHY properties. They are MDIO properties. It is the MDIO driver using them to perform an 'MDIO bus reset'. The property names are wrong. The device tree structure could be better. It mixes the MAC and the MDIO properties in the same node. It would of been better to have separate nodes. The MDIO core now has equivalent functionality. So yes, it would be better to use the generic MDIO properties, not these driver properties. Andrew ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac 2017-11-07 7:54 ` Vladimir Zapolskiy 2017-11-07 9:51 ` Chris Zhong 2017-11-07 15:59 ` Andrew Lunn @ 2017-11-09 8:20 ` Roger Quadros 2 siblings, 0 replies; 9+ messages in thread From: Roger Quadros @ 2017-11-09 8:20 UTC (permalink / raw) To: linux-arm-kernel Hi, On 07/11/17 09:54, Vladimir Zapolskiy wrote: > Hello Chris, > > On 11/07/2017 04:49 AM, Chris Zhong wrote: >> The ethernet phy of rk3066a-rayeager has a reset pin, it controlled by >> GPIO1_D6, this pin should be pull down then pull up to reset the phy. >> Add a phy-reset property in emac, make the phy can be reset when emac >> power on. > > for PHY reset there are properties 'reset-gpios' and 'reset-delay-us', > please reference to Documentation/devicetree/bindings/net/mdio.txt > > Can you try to reuse them instead of adding new custom properties? > > As a side question, which is mainly addressed to Sergei and Roger, > I don't quite understand why PHY properties were initially added to > MAC/MDIO bus device tree nodes, in my opinion they must be moved under > PHY device tree nodes. The PHY reset *has* to be performed at the MDIO bus driver level so that they can be pin-strap configured correctly and be detected during MDIO bus scan. - We have boards where PHYs won't be detected if RESET is not done before the scan. (due to invalid h/w pin-strapping config) - We have boards where a single GPIO line controls reset of all PHYs on the bus. Due to these reasons the RESET control lies with the MDIO bus driver. > > -- > With best wishes, > Vladimir > >> >> Signed-off-by: Chris Zhong <zyw@rock-chips.com> >> --- >> >> arch/arm/boot/dts/rk3066a-rayeager.dts | 2 ++ >> 1 file changed, 2 insertions(+) >> >> diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rk3066a-rayeager.dts >> index 570157f..6064a0a 100644 >> --- a/arch/arm/boot/dts/rk3066a-rayeager.dts >> +++ b/arch/arm/boot/dts/rk3066a-rayeager.dts >> @@ -173,6 +173,8 @@ >> pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>; >> phy = <&phy0>; >> phy-supply = <&vcc_rmii>; >> + phy-reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>; /* PHY_RST */ >> + phy-reset-duration = <10>; /* millisecond */ >> status = "okay"; >> >> phy0: ethernet-phy at 0 { >> -- cheers, -roger Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2017-11-09 8:40 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2017-11-07 2:49 [PATCH] ARM: dts: add phy-reset property for rk3066a-rayeager emac Chris Zhong 2017-11-07 7:54 ` Vladimir Zapolskiy 2017-11-07 9:51 ` Chris Zhong 2017-11-07 18:26 ` Florian Fainelli 2017-11-08 9:49 ` Chris Zhong 2017-11-09 8:28 ` Roger Quadros 2017-11-09 8:40 ` Roger Quadros 2017-11-07 15:59 ` Andrew Lunn 2017-11-09 8:20 ` Roger Quadros
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).