From: festevam@gmail.com (Fabio Estevam)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 3/5] ARM: dts: imx28-tx28: Pass unit address and reg to IOMUX node
Date: Wed, 27 Dec 2017 12:04:36 -0200 [thread overview]
Message-ID: <1514383478-32544-3-git-send-email-festevam@gmail.com> (raw)
In-Reply-To: <1514383478-32544-1-git-send-email-festevam@gmail.com>
From: Fabio Estevam <fabio.estevam@nxp.com>
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-edt-ft5x06-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-flexcan-xcvr-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-lcdif-23bit missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-lcdif-ctrl missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-mac0-gpio-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-pca9554-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/spi-gpiogrp missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-tsc2007-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-usbphy0-pins missing or empty reg/ranges property
arch/arm/boot/dts/imx28-tx28.dtb: Warning (simple_bus_reg): Node /apb at 80000000/apbh at 80000000/pinctrl at 80018000/tx28-usbphy1-pins missing or empty reg/ranges property
Cc: Lothar Wa?mann <LW@KARO-electronics.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
arch/arm/boot/dts/imx28-tx28.dts | 30 ++++++++++++++++++++----------
1 file changed, 20 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts
index 152621e..8a4f5bc 100644
--- a/arch/arm/boot/dts/imx28-tx28.dts
+++ b/arch/arm/boot/dts/imx28-tx28.dts
@@ -531,7 +531,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_edt_ft5x06_pins: tx28-edt-ft5x06-pins {
+ tx28_edt_ft5x06_pins: tx28-edt-ft5x06-pins at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA6__GPIO_2_6 /* RESET */
MX28_PAD_SSP0_DATA5__GPIO_2_5 /* IRQ */
@@ -542,7 +543,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_flexcan_xcvr_pins: tx28-flexcan-xcvr-pins {
+ tx28_flexcan_xcvr_pins: tx28-flexcan-xcvr-pins at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D00__GPIO_1_0
>;
@@ -551,7 +553,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_lcdif_23bit_pins: tx28-lcdif-23bit {
+ tx28_lcdif_23bit_pins: tx28-lcdif-23bit at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
/* LCD_D00 may be used as Flexcan Transceiver Enable on STK5-V5 */
MX28_PAD_LCD_D01__LCD_D1
@@ -583,7 +586,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_lcdif_ctrl_pins: tx28-lcdif-ctrl {
+ tx28_lcdif_ctrl_pins: tx28-lcdif-ctrl at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_ENABLE__GPIO_1_31 /* Enable */
MX28_PAD_LCD_RESET__GPIO_3_30 /* Reset */
@@ -593,7 +597,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_mac0_pins_gpio: tx28-mac0-gpio-pins {
+ tx28_mac0_pins_gpio: tx28-mac0-gpio-pins at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_ENET0_MDC__GPIO_4_0
MX28_PAD_ENET0_MDIO__GPIO_4_1
@@ -610,7 +615,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_pca9554_pins: tx28-pca9554-pins {
+ tx28_pca9554_pins: tx28-pca9554-pins at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_PWM3__GPIO_3_28
>;
@@ -619,7 +625,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_spi_gpio_pins: spi-gpiogrp {
+ tx28_spi_gpio_pins: spi-gpiogrp at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART2_RX__GPIO_3_8
MX28_PAD_AUART2_TX__GPIO_3_9
@@ -633,7 +640,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_tsc2007_pins: tx28-tsc2007-pins {
+ tx28_tsc2007_pins: tx28-tsc2007-pins at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SAIF0_MCLK__GPIO_3_20 /* TSC2007 IRQ */
>;
@@ -643,7 +651,8 @@
};
- tx28_usbphy0_pins: tx28-usbphy0-pins {
+ tx28_usbphy0_pins: tx28-usbphy0-pins at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_GPMI_CE2N__GPIO_0_18 /* USBOTG_VBUSEN */
MX28_PAD_GPMI_CE3N__GPIO_0_19 /* USBOTH_OC */
@@ -653,7 +662,8 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
- tx28_usbphy1_pins: tx28-usbphy1-pins {
+ tx28_usbphy1_pins: tx28-usbphy1-pins at 0 {
+ reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SPDIF__GPIO_3_27 /* USBH_VBUSEN */
MX28_PAD_JTAG_RTCK__GPIO_4_20 /* USBH_OC */
--
2.7.4
next prev parent reply other threads:[~2017-12-27 14:04 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-27 14:04 [PATCH 1/5] ARM: dts: imx23: Pass unit address and reg to IOMUX node Fabio Estevam
2017-12-27 14:04 ` [PATCH 2/5] ARM: dts: imx28: " Fabio Estevam
2017-12-27 14:04 ` Fabio Estevam [this message]
2018-01-08 8:15 ` [PATCH 3/5] ARM: dts: imx28-tx28: " Lothar Waßmann
2017-12-27 14:04 ` [PATCH 4/5] ARM: dts: imx28-apx4devkit: " Fabio Estevam
2017-12-27 14:04 ` [PATCH 5/5] ARM: dts: imx28-cfa10049: Move i2cmux out of bus node Fabio Estevam
2018-01-04 12:53 ` Maxime Ripard
2018-01-25 7:40 ` [PATCH 1/5] ARM: dts: imx23: Pass unit address and reg to IOMUX node Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1514383478-32544-3-git-send-email-festevam@gmail.com \
--to=festevam@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).