* [PATCH v2 01/11] soc: qcom: Separate kryo l2 accessors from PMU driver
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 02/11] clk: qcom: Fix .set_rate to handle alpha PLLs w/wo dynamic update Ilia Lin
` (9 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
The driver provides kernel level API for other drivers
to access the MSM8996 L2 cache registers.
Separating the L2 access code from the PMU driver and
making it public to allow other drivers use it.
The accesses must be separated with a single spinlock,
maintained in this driver.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
arch/arm64/Kconfig.platforms | 7 ++++
drivers/perf/qcom_l2_pmu.c | 48 +--------------------------
drivers/soc/qcom/Makefile | 1 +
drivers/soc/qcom/kryo-l2-accessors.c | 64 ++++++++++++++++++++++++++++++++++++
include/soc/qcom/kryo-l2-accessors.h | 22 +++++++++++++
5 files changed, 95 insertions(+), 47 deletions(-)
create mode 100644 drivers/soc/qcom/kryo-l2-accessors.c
create mode 100644 include/soc/qcom/kryo-l2-accessors.h
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 2401373..a6a6504 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -144,6 +144,13 @@ config ARCH_REALTEK
This enables support for the ARMv8 based Realtek chipsets,
like the RTD1295.
+config ARCH_MSM8996
+ bool "Enable Support for Qualcomm Technologies, Inc. MSM8996"
+ depends on ARCH_QCOM
+ help
+ This enables support for the MSM8996 chipset. If you do not
+ wish to build a kernel that runs on this chipset, say 'N' here.
+
config ARCH_ROCKCHIP
bool "Rockchip Platforms"
select ARCH_HAS_RESET_CONTROLLER
diff --git a/drivers/perf/qcom_l2_pmu.c b/drivers/perf/qcom_l2_pmu.c
index 4fdc848..ba5f241 100644
--- a/drivers/perf/qcom_l2_pmu.c
+++ b/drivers/perf/qcom_l2_pmu.c
@@ -30,7 +30,7 @@
#include <asm/barrier.h>
#include <asm/local64.h>
-#include <asm/sysreg.h>
+#include <soc/qcom/kryo-l2-accessors.h>
#define MAX_L2_CTRS 9
@@ -87,9 +87,6 @@
#define L2_COUNTER_RELOAD BIT_ULL(31)
#define L2_CYCLE_COUNTER_RELOAD BIT_ULL(63)
-#define L2CPUSRSELR_EL1 sys_reg(3, 3, 15, 0, 6)
-#define L2CPUSRDR_EL1 sys_reg(3, 3, 15, 0, 7)
-
#define reg_idx(reg, i) (((i) * IA_L2_REG_OFFSET) + reg##_BASE)
/*
@@ -107,49 +104,6 @@
#define L2_EVENT_STREX 0x421
#define L2_EVENT_CLREX 0x422
-static DEFINE_RAW_SPINLOCK(l2_access_lock);
-
-/**
- * set_l2_indirect_reg: write value to an L2 register
- * @reg: Address of L2 register.
- * @value: Value to be written to register.
- *
- * Use architecturally required barriers for ordering between system register
- * accesses
- */
-static void set_l2_indirect_reg(u64 reg, u64 val)
-{
- unsigned long flags;
-
- raw_spin_lock_irqsave(&l2_access_lock, flags);
- write_sysreg_s(reg, L2CPUSRSELR_EL1);
- isb();
- write_sysreg_s(val, L2CPUSRDR_EL1);
- isb();
- raw_spin_unlock_irqrestore(&l2_access_lock, flags);
-}
-
-/**
- * get_l2_indirect_reg: read an L2 register value
- * @reg: Address of L2 register.
- *
- * Use architecturally required barriers for ordering between system register
- * accesses
- */
-static u64 get_l2_indirect_reg(u64 reg)
-{
- u64 val;
- unsigned long flags;
-
- raw_spin_lock_irqsave(&l2_access_lock, flags);
- write_sysreg_s(reg, L2CPUSRSELR_EL1);
- isb();
- val = read_sysreg_s(L2CPUSRDR_EL1);
- raw_spin_unlock_irqrestore(&l2_access_lock, flags);
-
- return val;
-}
-
struct cluster_pmu;
/*
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index 40c56f6..2bf8d93 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -10,3 +10,4 @@ obj-$(CONFIG_QCOM_SMEM_STATE) += smem_state.o
obj-$(CONFIG_QCOM_SMP2P) += smp2p.o
obj-$(CONFIG_QCOM_SMSM) += smsm.o
obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o
+obj-$(CONFIG_ARCH_MSM8996) += kryo-l2-accessors.o
diff --git a/drivers/soc/qcom/kryo-l2-accessors.c b/drivers/soc/qcom/kryo-l2-accessors.c
new file mode 100644
index 0000000..6743848
--- /dev/null
+++ b/drivers/soc/qcom/kryo-l2-accessors.c
@@ -0,0 +1,64 @@
+/*
+ * Copyright (c) 2014-2015, 2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/spinlock.h>
+#include <asm/sysreg.h>
+#include <soc/qcom/kryo-l2-accessors.h>
+
+#define L2CPUSRSELR_EL1 sys_reg(3, 3, 15, 0, 6)
+#define L2CPUSRDR_EL1 sys_reg(3, 3, 15, 0, 7)
+
+static DEFINE_RAW_SPINLOCK(l2_access_lock);
+
+/**
+ * set_l2_indirect_reg: write value to an L2 register
+ * @reg: Address of L2 register.
+ * @value: Value to be written to register.
+ *
+ * Use architecturally required barriers for ordering between system register
+ * accesses, and system registers with respect to device memory
+ */
+void set_l2_indirect_reg(u64 reg, u64 val)
+{
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&l2_access_lock, flags);
+ write_sysreg_s(reg, L2CPUSRSELR_EL1);
+ isb();
+ write_sysreg_s(val, L2CPUSRDR_EL1);
+ isb();
+ raw_spin_unlock_irqrestore(&l2_access_lock, flags);
+}
+EXPORT_SYMBOL(set_l2_indirect_reg);
+
+/**
+ * get_l2_indirect_reg: read an L2 register value
+ * @reg: Address of L2 register.
+ *
+ * Use architecturally required barriers for ordering between system register
+ * accesses, and system registers with respect to device memory
+ */
+u64 get_l2_indirect_reg(u64 reg)
+{
+ u64 val;
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&l2_access_lock, flags);
+ write_sysreg_s(reg, L2CPUSRSELR_EL1);
+ isb();
+ val = read_sysreg_s(L2CPUSRDR_EL1);
+ raw_spin_unlock_irqrestore(&l2_access_lock, flags);
+
+ return val;
+}
+EXPORT_SYMBOL(get_l2_indirect_reg);
diff --git a/include/soc/qcom/kryo-l2-accessors.h b/include/soc/qcom/kryo-l2-accessors.h
new file mode 100644
index 0000000..e9a5eab
--- /dev/null
+++ b/include/soc/qcom/kryo-l2-accessors.h
@@ -0,0 +1,22 @@
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_MSM_MSM_KRYO_L2_ACCESSORS_H
+#define __ASM_ARCH_MSM_MSM_KRYO_L2_ACCESSORS_H
+
+#ifdef CONFIG_ARCH_QCOM
+void set_l2_indirect_reg(u64 reg_addr, u64 val);
+u64 get_l2_indirect_reg(u64 reg_addr);
+#endif
+
+#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 02/11] clk: qcom: Fix .set_rate to handle alpha PLLs w/wo dynamic update
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
2018-01-04 11:10 ` [PATCH v2 01/11] soc: qcom: Separate kryo l2 accessors from PMU driver Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 03/11] clk: qcom: Make clk_alpha_pll_configure available to modules Ilia Lin
` (8 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
From: Taniya Das <tdas@codeaurora.org>
From: Taniya Das <tdas@codeaurora.org>
Alpha PLLs which do not support dynamic update feature
need to be explicitly disabled before a rate change.
The ones which do support dynamic update do so within a
single vco range, so add a min/max freq check for such
PLLs so they fall in the vco range.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 72 ++++++++++++++++++++++++++++++++++------
drivers/clk/qcom/clk-alpha-pll.h | 5 +++
2 files changed, 66 insertions(+), 11 deletions(-)
diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 47a1da3..ffdb160 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -376,19 +376,47 @@ static unsigned long alpha_pll_calc_rate(u64 prate, u32 l, u32 a)
return alpha_pll_calc_rate(prate, l, a);
}
-static int clk_alpha_pll_set_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long prate)
+static int alpha_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long prate,
+ int (*enable)(struct clk_hw *hw),
+ void (*disable)(struct clk_hw *hw))
{
+ bool need_reenabling = false;
struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
const struct pll_vco *vco;
u32 l, off = pll->offset;
u64 a;
rate = alpha_pll_round_rate(rate, prate, &l, &a);
- vco = alpha_pll_find_vco(pll, rate);
- if (!vco) {
- pr_err("alpha pll not in a valid vco range\n");
- return -EINVAL;
+
+ if (pll->flags & SUPPORTS_DYNAMIC_UPDATE) {
+ /*
+ * PLLs which support dynamic updates support one single
+ * vco range, between min_rate and max_rate supported
+ */
+ if (rate < pll->min_rate || rate > pll->max_rate) {
+ pr_err("alpha pll rate outside supported min/max range\n");
+ return -EINVAL;
+ }
+ } else {
+ /*
+ * All alpha PLLs which do not support dynamic update,
+ * should be disabled before a vco update.
+ */
+ if (clk_hw_is_enabled(hw)) {
+ disable(hw);
+ need_reenabling = true;
+ }
+
+ vco = alpha_pll_find_vco(pll, rate);
+ if (!vco) {
+ pr_err("alpha pll not in a valid vco range\n");
+ return -EINVAL;
+ }
+
+ regmap_update_bits(pll->clkr.regmap, off + PLL_USER_CTL,
+ PLL_VCO_MASK << PLL_VCO_SHIFT,
+ vco->val << PLL_VCO_SHIFT);
}
regmap_write(pll->clkr.regmap, off + PLL_L_VAL, l);
@@ -401,16 +429,29 @@ static int clk_alpha_pll_set_rate(struct clk_hw *hw, unsigned long rate,
regmap_write(pll->clkr.regmap, off + PLL_ALPHA_VAL_U, a >> 32);
}
- regmap_update_bits(pll->clkr.regmap, off + PLL_USER_CTL,
- PLL_VCO_MASK << PLL_VCO_SHIFT,
- vco->val << PLL_VCO_SHIFT);
-
regmap_update_bits(pll->clkr.regmap, off + PLL_USER_CTL, PLL_ALPHA_EN,
PLL_ALPHA_EN);
+ if (need_reenabling)
+ enable(hw);
+
return 0;
}
+static int clk_alpha_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long prate)
+{
+ return alpha_pll_set_rate(hw, rate, prate, clk_alpha_pll_enable,
+ clk_alpha_pll_disable);
+}
+
+static int clk_alpha_pll_hwfsm_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long prate)
+{
+ return alpha_pll_set_rate(hw, rate, prate, clk_alpha_pll_hwfsm_enable,
+ clk_alpha_pll_hwfsm_disable);
+}
+
static long clk_alpha_pll_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long *prate)
{
@@ -420,6 +461,15 @@ static long clk_alpha_pll_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long min_freq, max_freq;
rate = alpha_pll_round_rate(rate, *prate, &l, &a);
+
+ if (pll->flags & SUPPORTS_DYNAMIC_UPDATE) {
+ if (rate < pll->min_rate)
+ rate = pll->min_rate;
+ else if (rate > pll->max_rate)
+ rate = pll->max_rate;
+ return rate;
+ }
+
if (alpha_pll_find_vco(pll, rate))
return rate;
@@ -445,7 +495,7 @@ static long clk_alpha_pll_round_rate(struct clk_hw *hw, unsigned long rate,
.is_enabled = clk_alpha_pll_hwfsm_is_enabled,
.recalc_rate = clk_alpha_pll_recalc_rate,
.round_rate = clk_alpha_pll_round_rate,
- .set_rate = clk_alpha_pll_set_rate,
+ .set_rate = clk_alpha_pll_hwfsm_set_rate,
};
EXPORT_SYMBOL_GPL(clk_alpha_pll_hwfsm_ops);
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index d6e1ee2..7aaa11c 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -27,6 +27,8 @@ struct pll_vco {
* struct clk_alpha_pll - phase locked loop (PLL)
* @offset: base address of registers
* @vco_table: array of VCO settings
+ * @min_rate: Minimim rate for PLLs with single VCO range
+ * @max_rate: Maximun rate for PLLs with single VCO range
* @clkr: regmap clock handle
*/
struct clk_alpha_pll {
@@ -37,8 +39,11 @@ struct clk_alpha_pll {
#define SUPPORTS_OFFLINE_REQ BIT(0)
#define SUPPORTS_16BIT_ALPHA BIT(1)
#define SUPPORTS_FSM_MODE BIT(2)
+#define SUPPORTS_DYNAMIC_UPDATE BIT(3)
u8 flags;
+ unsigned long min_rate;
+ unsigned long max_rate;
struct clk_regmap clkr;
};
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 03/11] clk: qcom: Make clk_alpha_pll_configure available to modules
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
2018-01-04 11:10 ` [PATCH v2 01/11] soc: qcom: Separate kryo l2 accessors from PMU driver Ilia Lin
2018-01-04 11:10 ` [PATCH v2 02/11] clk: qcom: Fix .set_rate to handle alpha PLLs w/wo dynamic update Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 04/11] clk: qcom: Add CPU clock driver for msm8996 Ilia Lin
` (7 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
From: Rajendra Nayak <rnayak@codeaurora.org>
Allow clk_alpha_pll_configure to be called from loadable
kernel modules.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index ffdb160..b41a2ad4 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -141,6 +141,7 @@ void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
if (pll->flags & SUPPORTS_FSM_MODE)
qcom_pll_set_fsm_mode(regmap, off + PLL_MODE, 6, 0);
}
+EXPORT_SYMBOL_GPL(clk_alpha_pll_configure);
static int clk_alpha_pll_hwfsm_enable(struct clk_hw *hw)
{
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 04/11] clk: qcom: Add CPU clock driver for msm8996
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
` (2 preceding siblings ...)
2018-01-04 11:10 ` [PATCH v2 03/11] clk: qcom: Make clk_alpha_pll_configure available to modules Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 05/11] clk: qcom: Add DT bindings for " Ilia Lin
` (6 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
From: Rajendra Nayak <rnayak@codeaurora.org>
Each of the CPU clusters (Power and Perf) on msm8996 are
clocked via 2 PLLs, a primary and alternate. There are also
2 Mux'es, a primary and secondary all connected together
as shown below
+-------+
XO | |
+------------------>0 |
| |
PLL/2 | SMUX +----+
+------->1 | |
| | | |
| +-------+ | +-------+
| +---->0 |
| | |
+---------------+ | +----------->1 | CPU clk
|Primary PLL +----+ PLL_EARLY | | +------>
| +------+-----------+ +------>2 PMUX |
+---------------+ | | | |
| +------+ | +-->3 |
+--^+ ACD +-----+ | +-------+
+---------------+ +------+ |
|Alt PLL | |
| +---------------------------+
+---------------+ PLL_EARLY
The primary PLL is what drives the CPU clk, except for times
when we are reprogramming the PLL itself (for rate changes) when
we temporarily switch to an alternate PLL. A subsequent patch adds
support to switch between primary and alternate PLL during rate
changes.
The primary PLL operates on a single VCO range, between 600Mhz
and 3Ghz. However the CPUs do support OPPs with frequencies
between 300Mhz and 600Mhz. In order to support running the CPUs
at those frequencies we end up having to lock the PLL at twice
the rate and drive the CPU clk via the PLL/2 output and SMUX.
So for frequencies above 600Mhz we follow the following path
Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
and for frequencies between 300Mhz and 600Mhz we follow
Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk
Support for this is added in a subsequent patch as well.
ACD stands for Adaptive Clock Distribution and is used to
detect voltage droops. We do not add support for ACD as yet.
This can be added at a later point as needed.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/Kconfig | 8 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/clk-cpu-8996.c | 388 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 397 insertions(+)
create mode 100644 drivers/clk/qcom/clk-cpu-8996.c
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 9f6c278..124fb9a4 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -196,3 +196,11 @@ config MSM_MMCC_8996
Support for the multimedia clock controller on msm8996 devices.
Say Y if you want to support multimedia devices such as display,
graphics, video encode/decode, camera, etc.
+
+config MSM_APCC_8996
+ tristate "MSM8996 CPU Clock Controller"
+ depends on COMMON_CLK_QCOM
+ help
+ Support for the CPU clock controller on msm8996 devices.
+ Say Y if you want to support CPU clock scaling using CPUfreq
+ drivers for dyanmic power management.
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 26410d3..b964f43 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -32,5 +32,6 @@ obj-$(CONFIG_MSM_LCC_8960) += lcc-msm8960.o
obj-$(CONFIG_MSM_MMCC_8960) += mmcc-msm8960.o
obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
obj-$(CONFIG_MSM_MMCC_8996) += mmcc-msm8996.o
+obj-$(CONFIG_MSM_APCC_8996) += clk-cpu-8996.o
obj-$(CONFIG_QCOM_CLK_RPM) += clk-rpm.o
obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
new file mode 100644
index 0000000..bc60111
--- /dev/null
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -0,0 +1,388 @@
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "clk-alpha-pll.h"
+
+#define VCO(a, b, c) { \
+ .val = a,\
+ .min_freq = b,\
+ .max_freq = c,\
+}
+
+#define DIV_2_INDEX 0
+#define PLL_INDEX 1
+#define ACD_INDEX 2
+#define ALT_INDEX 3
+
+/* PLLs */
+
+static const struct alpha_pll_config hfpll_config = {
+ .l = 60,
+ .config_ctl_val = 0x200d4828,
+ .config_ctl_hi_val = 0x006,
+ .pre_div_mask = BIT(12),
+ .post_div_mask = 0x3 << 8,
+ .main_output_mask = BIT(0),
+ .early_output_mask = BIT(3),
+};
+
+static struct clk_alpha_pll perfcl_pll = {
+ .offset = 0x80000,
+ .min_rate = 600000000,
+ .max_rate = 3000000000,
+ .flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_16BIT_ALPHA
+ | SUPPORTS_FSM_MODE,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "perfcl_pll",
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_hwfsm_ops,
+ },
+};
+
+static struct clk_alpha_pll pwrcl_pll = {
+ .offset = 0x0,
+ .min_rate = 600000000,
+ .max_rate = 3000000000,
+ .flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_16BIT_ALPHA
+ | SUPPORTS_FSM_MODE,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "pwrcl_pll",
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_hwfsm_ops,
+ },
+};
+
+static const struct pll_vco alt_pll_vco_modes[] = {
+ VCO(3, 250000000, 500000000),
+ VCO(2, 500000000, 750000000),
+ VCO(1, 750000000, 1000000000),
+ VCO(0, 1000000000, 2150400000),
+};
+
+static const struct alpha_pll_config altpll_config = {
+ .l = 16,
+ .vco_val = 0x3 << 20,
+ .vco_mask = 0x3 << 20,
+ .config_ctl_val = 0x4001051b,
+ .post_div_mask = 0x3 << 8,
+ .post_div_val = 0x1,
+ .main_output_mask = BIT(0),
+ .early_output_mask = BIT(3),
+};
+
+static struct clk_alpha_pll perfcl_alt_pll = {
+ .offset = 0x80100,
+ .vco_table = alt_pll_vco_modes,
+ .num_vco = ARRAY_SIZE(alt_pll_vco_modes),
+ .flags = SUPPORTS_OFFLINE_REQ | SUPPORTS_FSM_MODE,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "perfcl_alt_pll",
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_hwfsm_ops,
+ },
+};
+
+static struct clk_alpha_pll pwrcl_alt_pll = {
+ .offset = 0x100,
+ .vco_table = alt_pll_vco_modes,
+ .num_vco = ARRAY_SIZE(alt_pll_vco_modes),
+ .flags = SUPPORTS_OFFLINE_REQ | SUPPORTS_FSM_MODE,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "pwrcl_alt_pll",
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_hwfsm_ops,
+ },
+};
+
+/* Mux'es */
+
+struct clk_cpu_8996_mux {
+ u32 reg;
+ u32 shift;
+ u32 width;
+ struct clk_hw *pll;
+ struct clk_regmap clkr;
+};
+
+static inline
+struct clk_cpu_8996_mux *to_clk_cpu_8996_mux_hw(struct clk_hw *hw)
+{
+ return container_of(to_clk_regmap(hw), struct clk_cpu_8996_mux, clkr);
+}
+
+static u8 clk_cpu_8996_mux_get_parent(struct clk_hw *hw)
+{
+ unsigned int val;
+ struct clk_regmap *clkr = to_clk_regmap(hw);
+ struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+ unsigned int mask = GENMASK(cpuclk->width - 1, 0);
+
+ regmap_read(clkr->regmap, cpuclk->reg, &val);
+
+ val >>= cpuclk->shift;
+ val &= mask;
+
+ return val;
+}
+
+static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+ unsigned int val;
+ struct clk_regmap *clkr = to_clk_regmap(hw);
+ struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+ unsigned int mask = GENMASK(cpuclk->width + cpuclk->shift - 1,
+ cpuclk->shift);
+
+ val = index;
+ val = cpuclk->shift;
+
+ return regmap_update_bits(clkr->regmap, cpuclk->reg, mask, val);
+}
+
+static int
+clk_cpu_8996_mux_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
+{
+ struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+ struct clk_hw *parent = cpuclk->pll;
+
+ if (!cpuclk->pll)
+ return -EINVAL;
+
+ req->best_parent_rate = clk_hw_round_rate(parent, req->rate);
+ req->best_parent_hw = parent;
+
+ return 0;
+}
+
+const struct clk_ops clk_cpu_8996_mux_ops = {
+ .set_parent = clk_cpu_8996_mux_set_parent,
+ .get_parent = clk_cpu_8996_mux_get_parent,
+ .determine_rate = clk_cpu_8996_mux_determine_rate,
+};
+
+static struct clk_cpu_8996_mux pwrcl_smux = {
+ .reg = 0x40,
+ .shift = 2,
+ .width = 2,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "pwrcl_smux",
+ .parent_names = (const char *[]){
+ "xo",
+ "pwrcl_pll_main",
+ },
+ .num_parents = 2,
+ .ops = &clk_cpu_8996_mux_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_cpu_8996_mux perfcl_smux = {
+ .reg = 0x80040,
+ .shift = 2,
+ .width = 2,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "perfcl_smux",
+ .parent_names = (const char *[]){
+ "xo",
+ "perfcl_pll_main",
+ },
+ .num_parents = 2,
+ .ops = &clk_cpu_8996_mux_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_cpu_8996_mux pwrcl_pmux = {
+ .reg = 0x40,
+ .shift = 0,
+ .width = 2,
+ .pll = &pwrcl_pll.clkr.hw,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "pwrcl_pmux",
+ .parent_names = (const char *[]){
+ "pwrcl_smux",
+ "pwrcl_pll",
+ "pwrcl_pll_acd",
+ "pwrcl_alt_pll",
+ },
+ .num_parents = 4,
+ .ops = &clk_cpu_8996_mux_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_cpu_8996_mux perfcl_pmux = {
+ .reg = 0x80040,
+ .shift = 0,
+ .width = 2,
+ .pll = &perfcl_pll.clkr.hw,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "perfcl_pmux",
+ .parent_names = (const char *[]){
+ "perfcl_smux",
+ "perfcl_pll",
+ "pwrcl_pll_acd",
+ "perfcl_alt_pll",
+ },
+ .num_parents = 4,
+ .ops = &clk_cpu_8996_mux_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static const struct regmap_config cpu_msm8996_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0x80210,
+ .fast_io = true,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+};
+
+static const struct of_device_id match_table[] = {
+ { .compatible = "qcom,apcc-msm8996" },
+ {}
+};
+
+struct clk_regmap *clks[] = {
+ /* PLLs */
+ &perfcl_pll.clkr,
+ &pwrcl_pll.clkr,
+ &perfcl_alt_pll.clkr,
+ &pwrcl_alt_pll.clkr,
+ /* MUXs */
+ &perfcl_smux.clkr,
+ &pwrcl_smux.clkr,
+ &perfcl_pmux.clkr,
+ &pwrcl_pmux.clkr,
+};
+
+struct clk_hw_clks {
+ unsigned int num;
+ struct clk_hw *hws[];
+};
+
+static int
+qcom_cpu_clk_msm8996_register_clks(struct device *dev, struct clk_hw_clks *hws,
+ struct regmap *regmap)
+{
+ int i, ret;
+
+ hws->hws[0] = clk_hw_register_fixed_factor(dev, "perfcl_pll_main",
+ "perfcl_pll",
+ CLK_SET_RATE_PARENT, 1, 2);
+ perfcl_smux.pll = hws->hws[0];
+
+ hws->hws[1] = clk_hw_register_fixed_factor(dev, "pwrcl_pll_main",
+ "pwrcl_pll",
+ CLK_SET_RATE_PARENT, 1, 2);
+ pwrcl_smux.pll = hws->hws[1];
+
+ hws->num = 2;
+
+ for (i = 0; i < ARRAY_SIZE(clks); i++) {
+ ret = devm_clk_register_regmap(dev, clks[i]);
+ if (ret)
+ return ret;
+ }
+
+ clk_alpha_pll_configure(&perfcl_pll, regmap, &hfpll_config);
+ clk_alpha_pll_configure(&pwrcl_pll, regmap, &hfpll_config);
+ clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
+ clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
+
+ return ret;
+}
+
+static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
+{
+ int ret;
+ void __iomem *base;
+ struct resource *res;
+ struct regmap *regmap_cpu;
+ struct clk_hw_clks *hws;
+ struct clk_hw_onecell_data *data;
+ struct device *dev = &pdev->dev;
+ struct device_node *node = dev->of_node;
+
+ data = devm_kzalloc(dev, sizeof(*data) + 2 * sizeof(struct clk_hw *),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ hws = devm_kzalloc(dev, sizeof(*hws) + 2 * sizeof(struct clk_hw *),
+ GFP_KERNEL);
+ if (!hws)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ regmap_cpu = devm_regmap_init_mmio(dev, base,
+ &cpu_msm8996_regmap_config);
+ if (IS_ERR(regmap_cpu))
+ return PTR_ERR(regmap_cpu);
+
+ ret = qcom_cpu_clk_msm8996_register_clks(dev, hws, regmap_cpu);
+ if (ret)
+ return ret;
+
+ data->hws[0] = &pwrcl_pmux.clkr.hw;
+ data->hws[1] = &perfcl_pmux.clkr.hw;
+
+ data->num = 2;
+
+ platform_set_drvdata(pdev, hws);
+
+ return of_clk_add_hw_provider(node, of_clk_hw_onecell_get, data);
+}
+
+static int qcom_cpu_clk_msm8996_driver_remove(struct platform_device *pdev)
+{
+ int i;
+ struct device *dev = &pdev->dev;
+ struct clk_hw_clks *hws = platform_get_drvdata(pdev);
+
+ for (i = 0; i < hws->num; i++)
+ clk_hw_unregister_fixed_rate(hws->hws[i]);
+
+ of_clk_del_provider(dev->of_node);
+
+ return 0;
+}
+
+static struct platform_driver qcom_cpu_clk_msm8996_driver = {
+ .probe = qcom_cpu_clk_msm8996_driver_probe,
+ .remove = qcom_cpu_clk_msm8996_driver_remove,
+ .driver = {
+ .name = "qcom-apcc-msm8996",
+ .of_match_table = match_table,
+ },
+};
+
+module_platform_driver(qcom_cpu_clk_msm8996_driver);
+
+MODULE_ALIAS("platform:apcc-msm8996");
+MODULE_DESCRIPTION("QCOM MSM8996 CPU clock Driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 05/11] clk: qcom: Add DT bindings for CPU clock driver for msm8996
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
` (3 preceding siblings ...)
2018-01-04 11:10 ` [PATCH v2 04/11] clk: qcom: Add CPU clock driver for msm8996 Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-09 3:37 ` Rob Herring
2018-01-04 11:10 ` [PATCH v2 06/11] clk: qcom: cpu-8996: Add support to switch to alternate PLL Ilia Lin
` (5 subsequent siblings)
10 siblings, 1 reply; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
Documentation/devicetree/bindings/clock/qcom,kryocc.txt | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,kryocc.txt
diff --git a/Documentation/devicetree/bindings/clock/qcom,kryocc.txt b/Documentation/devicetree/bindings/clock/qcom,kryocc.txt
new file mode 100644
index 0000000..c45de03
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,kryocc.txt
@@ -0,0 +1,17 @@
+Qualcomm CPUSS clock controller for Kryo CPUs
+----------------------------------------------------
+
+Required properties :
+- compatible : shall contain only one of the following:
+
+ "qcom,apcc-msm8996"
+
+- reg : shall contain base register location and length
+- #clock-cells : shall contain 1
+
+Example:
+ kryocc: clock-controller at 6400000 {
+ compatible = "qcom,apcc-msm8996";
+ reg = <0x6400000 0x90000>;
+ #clock-cells = <1>;
+ };
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 05/11] clk: qcom: Add DT bindings for CPU clock driver for msm8996
2018-01-04 11:10 ` [PATCH v2 05/11] clk: qcom: Add DT bindings for " Ilia Lin
@ 2018-01-09 3:37 ` Rob Herring
0 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2018-01-09 3:37 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 04, 2018 at 01:10:09PM +0200, Ilia Lin wrote:
> Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
> ---
> Documentation/devicetree/bindings/clock/qcom,kryocc.txt | 17 +++++++++++++++++
> 1 file changed, 17 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/qcom,kryocc.txt
>
> diff --git a/Documentation/devicetree/bindings/clock/qcom,kryocc.txt b/Documentation/devicetree/bindings/clock/qcom,kryocc.txt
> new file mode 100644
> index 0000000..c45de03
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/qcom,kryocc.txt
> @@ -0,0 +1,17 @@
> +Qualcomm CPUSS clock controller for Kryo CPUs
> +----------------------------------------------------
> +
> +Required properties :
> +- compatible : shall contain only one of the following:
> +
> + "qcom,apcc-msm8996"
qcom-msm8996-apcc is the conventional order.
> +
> +- reg : shall contain base register location and length
> +- #clock-cells : shall contain 1
> +
> +Example:
> + kryocc: clock-controller at 6400000 {
> + compatible = "qcom,apcc-msm8996";
> + reg = <0x6400000 0x90000>;
> + #clock-cells = <1>;
> + };
> --
> 1.9.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v2 06/11] clk: qcom: cpu-8996: Add support to switch to alternate PLL
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
` (4 preceding siblings ...)
2018-01-04 11:10 ` [PATCH v2 05/11] clk: qcom: Add DT bindings for " Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 07/11] clk: qcom: cpu-8996: Add support to switch below 600Mhz Ilia Lin
` (4 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
From: Rajendra Nayak <rnayak@codeaurora.org>
Each of the CPU clusters on msm8996 and powered via a primary
PLL and a secondary PLL. The primary PLL is what drivers the
CPU clk, except for times when we are reprogramming the PLL
itself, when we temporarily switch to an alternate PLL.
Use clock rate change notifiers to support this.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-cpu-8996.c | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index bc60111..9bb25be 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -119,10 +119,14 @@ struct clk_cpu_8996_mux {
u32 reg;
u32 shift;
u32 width;
+ struct notifier_block nb;
struct clk_hw *pll;
struct clk_regmap clkr;
};
+#define to_clk_cpu_8996_mux_nb(_nb) \
+ container_of(_nb, struct clk_cpu_8996_mux, nb)
+
static inline
struct clk_cpu_8996_mux *to_clk_cpu_8996_mux_hw(struct clk_hw *hw)
{
@@ -173,6 +177,27 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
return 0;
}
+int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
+ void *data)
+{
+ int ret;
+ struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_nb(nb);
+
+ switch (event) {
+ case PRE_RATE_CHANGE:
+ ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
+ break;
+ case POST_RATE_CHANGE:
+ ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, PLL_INDEX);
+ break;
+ default:
+ ret = 0;
+ break;
+ }
+
+ return notifier_from_errno(ret);
+};
+
const struct clk_ops clk_cpu_8996_mux_ops = {
.set_parent = clk_cpu_8996_mux_set_parent,
.get_parent = clk_cpu_8996_mux_get_parent,
@@ -216,6 +241,7 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
.shift = 0,
.width = 2,
.pll = &pwrcl_pll.clkr.hw,
+ .nb.notifier_call = cpu_clk_notifier_cb,
.clkr.hw.init = &(struct clk_init_data) {
.name = "pwrcl_pmux",
.parent_names = (const char *[]){
@@ -235,6 +261,7 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
.shift = 0,
.width = 2,
.pll = &perfcl_pll.clkr.hw,
+ .nb.notifier_call = cpu_clk_notifier_cb,
.clkr.hw.init = &(struct clk_init_data) {
.name = "perfcl_pmux",
.parent_names = (const char *[]){
@@ -310,6 +337,14 @@ struct clk_hw_clks {
clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
+ ret = clk_notifier_register(pwrcl_pmux.clkr.hw.clk, &pwrcl_pmux.nb);
+ if (ret)
+ return ret;
+
+ ret = clk_notifier_register(perfcl_pmux.clkr.hw.clk, &perfcl_pmux.nb);
+ if (ret)
+ return ret;
+
return ret;
}
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 07/11] clk: qcom: cpu-8996: Add support to switch below 600Mhz
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
` (5 preceding siblings ...)
2018-01-04 11:10 ` [PATCH v2 06/11] clk: qcom: cpu-8996: Add support to switch to alternate PLL Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 08/11] clk: qcom: clk-cpu-8996: Prepare PLLs on probe Ilia Lin
` (3 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
From: Rajendra Nayak <rnayak@codeaurora.org>
The CPU clock controllers primary PLL operates on a single VCO range,
between 600Mhz and 3Ghz. However the CPUs do support OPPs with
frequencies between 300Mhz and 600Mhz. In order to support running the
CPUs at those frequencies we end up having to lock the PLL at twice the
rate and drive the CPU clk via the PLL/2 output and SMUX.
So for frequencies above 600Mhz we follow the following path
Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
and for frequencies between 300Mhz and 600Mhz we follow
Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-cpu-8996.c | 24 +++++++++++++++++++++---
1 file changed, 21 insertions(+), 3 deletions(-)
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index 9bb25be..81cf466 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -28,15 +28,17 @@
#define PLL_INDEX 1
#define ACD_INDEX 2
#define ALT_INDEX 3
+#define DIV_2_THRESHOLD 600000000
/* PLLs */
static const struct alpha_pll_config hfpll_config = {
.l = 60,
- .config_ctl_val = 0x200d4828,
+ .config_ctl_val = 0x200D4AA8,
.config_ctl_hi_val = 0x006,
.pre_div_mask = BIT(12),
.post_div_mask = 0x3 << 8,
+ .post_div_val = 0x1 << 8,
.main_output_mask = BIT(0),
.early_output_mask = BIT(3),
};
@@ -82,7 +84,7 @@
.vco_mask = 0x3 << 20,
.config_ctl_val = 0x4001051b,
.post_div_mask = 0x3 << 8,
- .post_div_val = 0x1,
+ .post_div_val = 0x1 << 8,
.main_output_mask = BIT(0),
.early_output_mask = BIT(3),
};
@@ -121,6 +123,7 @@ struct clk_cpu_8996_mux {
u32 width;
struct notifier_block nb;
struct clk_hw *pll;
+ struct clk_hw *pll_div_2;
struct clk_regmap clkr;
};
@@ -171,6 +174,13 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
if (!cpuclk->pll)
return -EINVAL;
+ if (cpuclk->pll_div_2 && req->rate < DIV_2_THRESHOLD) {
+ if (req->rate < (DIV_2_THRESHOLD / 2))
+ return -EINVAL;
+
+ parent = cpuclk->pll_div_2;
+ }
+
req->best_parent_rate = clk_hw_round_rate(parent, req->rate);
req->best_parent_hw = parent;
@@ -182,13 +192,19 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
{
int ret;
struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_nb(nb);
+ struct clk_notifier_data *cnd = data;
switch (event) {
case PRE_RATE_CHANGE:
ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
break;
case POST_RATE_CHANGE:
- ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, PLL_INDEX);
+ if (cnd->new_rate < DIV_2_THRESHOLD)
+ ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
+ DIV_2_INDEX);
+ else
+ ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
+ PLL_INDEX);
break;
default:
ret = 0;
@@ -241,6 +257,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
.shift = 0,
.width = 2,
.pll = &pwrcl_pll.clkr.hw,
+ .pll_div_2 = &pwrcl_smux.clkr.hw,
.nb.notifier_call = cpu_clk_notifier_cb,
.clkr.hw.init = &(struct clk_init_data) {
.name = "pwrcl_pmux",
@@ -261,6 +278,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
.shift = 0,
.width = 2,
.pll = &perfcl_pll.clkr.hw,
+ .pll_div_2 = &perfcl_smux.clkr.hw,
.nb.notifier_call = cpu_clk_notifier_cb,
.clkr.hw.init = &(struct clk_init_data) {
.name = "perfcl_pmux",
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 08/11] clk: qcom: clk-cpu-8996: Prepare PLLs on probe
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
` (6 preceding siblings ...)
2018-01-04 11:10 ` [PATCH v2 07/11] clk: qcom: cpu-8996: Add support to switch below 600Mhz Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 09/11] clk: qcom: Add ACD path to CPU clock driver for msm8996 Ilia Lin
` (2 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
The PLLs must be prepared enabled during the probe to be
accessible by the OPPs. Otherwise an OPP may switch
to non-enabled clock.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-cpu-8996.c | 22 +++++++++++++++++-----
1 file changed, 17 insertions(+), 5 deletions(-)
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index 81cf466..f1bfd13 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -15,7 +15,7 @@
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
-
+#include <linux/clk-provider.h>
#include "clk-alpha-pll.h"
#define VCO(a, b, c) { \
@@ -160,7 +160,7 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
cpuclk->shift);
val = index;
- val = cpuclk->shift;
+ val <<= cpuclk->shift;
return regmap_update_bits(clkr->regmap, cpuclk->reg, mask, val);
}
@@ -269,7 +269,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
},
.num_parents = 4,
.ops = &clk_cpu_8996_mux_ops,
- .flags = CLK_SET_RATE_PARENT,
+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
},
};
@@ -285,12 +285,12 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
.parent_names = (const char *[]){
"perfcl_smux",
"perfcl_pll",
- "pwrcl_pll_acd",
+ "perfcl_pll_acd",
"perfcl_alt_pll",
},
.num_parents = 4,
.ops = &clk_cpu_8996_mux_ops,
- .flags = CLK_SET_RATE_PARENT,
+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
},
};
@@ -355,6 +355,18 @@ struct clk_hw_clks {
clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
+ /* Enable all PLLs and alt PLLs */
+ clk_prepare_enable(pwrcl_alt_pll.clkr.hw.clk);
+ clk_prepare_enable(perfcl_alt_pll.clkr.hw.clk);
+ clk_prepare_enable(pwrcl_pll.clkr.hw.clk);
+ clk_prepare_enable(perfcl_pll.clkr.hw.clk);
+
+ /* Set initial boot frequencies for power/perf PLLs */
+ clk_set_rate(pwrcl_alt_pll.clkr.hw.clk, 652800000);
+ clk_set_rate(perfcl_alt_pll.clkr.hw.clk, 652800000);
+ clk_set_rate(pwrcl_pll.clkr.hw.clk, 652800000);
+ clk_set_rate(perfcl_pll.clkr.hw.clk, 652800000);
+
ret = clk_notifier_register(pwrcl_pmux.clkr.hw.clk, &pwrcl_pmux.nb);
if (ret)
return ret;
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 09/11] clk: qcom: Add ACD path to CPU clock driver for msm8996
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
` (7 preceding siblings ...)
2018-01-04 11:10 ` [PATCH v2 08/11] clk: qcom: clk-cpu-8996: Prepare PLLs on probe Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 10/11] DT: QCOM: Add cpufreq-dt to msm8996 Ilia Lin
2018-01-04 11:10 ` [PATCH v2 11/11] DT: QCOM: Add thermal mitigation " Ilia Lin
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
The PMUX for each duplex allows for selection of ACD clock source.
The DVM (Dynamic Variation Monitor) will flag an error
when a voltage droop event is detected. This flagged error
enables ACD to provide a div-by-2 clock, sourced from the primary PLL.
The duplex will be provided the divided clock
until a pre-programmed delay has expired.
This change configures ACD during the probe and switches
the PMUXes to the ACD clock source.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-cpu-8996.c | 122 ++++++++++++++++++++++++++++++++++------
1 file changed, 106 insertions(+), 16 deletions(-)
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index f1bfd13..d38ff6d 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -17,6 +17,7 @@
#include <linux/regmap.h>
#include <linux/clk-provider.h>
#include "clk-alpha-pll.h"
+#include <soc/qcom/kryo-l2-accessors.h>
#define VCO(a, b, c) { \
.val = a,\
@@ -29,6 +30,27 @@
#define ACD_INDEX 2
#define ALT_INDEX 3
#define DIV_2_THRESHOLD 600000000
+#define PWRCL_REG_OFFSET 0x0
+#define PERFCL_REG_OFFSET 0x80000
+#define MUX_OFFSET 0x40
+#define ALT_PLL_OFFSET 0x100
+#define SSSCTL_OFFSET 0x160
+/*
+APCy_QLL_SSSCTL value:
+SACDRCLEN=1
+SSWEN=1
+SSTRTEN=1
+SSTPAPMSWEN=1
+*/
+#define SSSCTL_VAL 0xF
+
+enum {
+ APC_BASE,
+ EFUSE_BASE,
+ NUM_BASES
+};
+
+static void __iomem *vbases[NUM_BASES];
/* PLLs */
@@ -44,7 +66,7 @@
};
static struct clk_alpha_pll perfcl_pll = {
- .offset = 0x80000,
+ .offset = PERFCL_REG_OFFSET,
.min_rate = 600000000,
.max_rate = 3000000000,
.flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_16BIT_ALPHA
@@ -58,7 +80,7 @@
};
static struct clk_alpha_pll pwrcl_pll = {
- .offset = 0x0,
+ .offset = PWRCL_REG_OFFSET,
.min_rate = 600000000,
.max_rate = 3000000000,
.flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_16BIT_ALPHA
@@ -90,7 +112,7 @@
};
static struct clk_alpha_pll perfcl_alt_pll = {
- .offset = 0x80100,
+ .offset = PERFCL_REG_OFFSET + ALT_PLL_OFFSET,
.vco_table = alt_pll_vco_modes,
.num_vco = ARRAY_SIZE(alt_pll_vco_modes),
.flags = SUPPORTS_OFFLINE_REQ | SUPPORTS_FSM_MODE,
@@ -103,7 +125,7 @@
};
static struct clk_alpha_pll pwrcl_alt_pll = {
- .offset = 0x100,
+ .offset = PWRCL_REG_OFFSET + ALT_PLL_OFFSET,
.vco_table = alt_pll_vco_modes,
.num_vco = ARRAY_SIZE(alt_pll_vco_modes),
.flags = SUPPORTS_OFFLINE_REQ | SUPPORTS_FSM_MODE,
@@ -114,6 +136,7 @@
.ops = &clk_alpha_pll_hwfsm_ops,
},
};
+static void qcom_cpu_clk_msm8996_acd_init(void);
/* Mux'es */
@@ -197,6 +220,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
switch (event) {
case PRE_RATE_CHANGE:
ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
+ qcom_cpu_clk_msm8996_acd_init();
break;
case POST_RATE_CHANGE:
if (cnd->new_rate < DIV_2_THRESHOLD)
@@ -204,7 +228,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
DIV_2_INDEX);
else
ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
- PLL_INDEX);
+ ACD_INDEX);
break;
default:
ret = 0;
@@ -221,7 +245,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
};
static struct clk_cpu_8996_mux pwrcl_smux = {
- .reg = 0x40,
+ .reg = PWRCL_REG_OFFSET + MUX_OFFSET,
.shift = 2,
.width = 2,
.clkr.hw.init = &(struct clk_init_data) {
@@ -237,7 +261,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
};
static struct clk_cpu_8996_mux perfcl_smux = {
- .reg = 0x80040,
+ .reg = PERFCL_REG_OFFSET + MUX_OFFSET,
.shift = 2,
.width = 2,
.clkr.hw.init = &(struct clk_init_data) {
@@ -253,7 +277,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
};
static struct clk_cpu_8996_mux pwrcl_pmux = {
- .reg = 0x40,
+ .reg = PWRCL_REG_OFFSET + MUX_OFFSET,
.shift = 0,
.width = 2,
.pll = &pwrcl_pll.clkr.hw,
@@ -274,7 +298,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
};
static struct clk_cpu_8996_mux perfcl_pmux = {
- .reg = 0x80040,
+ .reg = PERFCL_REG_OFFSET + MUX_OFFSET,
.shift = 0,
.width = 2,
.pll = &perfcl_pll.clkr.hw,
@@ -342,7 +366,17 @@ struct clk_hw_clks {
CLK_SET_RATE_PARENT, 1, 2);
pwrcl_smux.pll = hws->hws[1];
- hws->num = 2;
+ hws->hws[2] = clk_hw_register_fixed_factor(dev, "perfcl_pll_acd",
+ "perfcl_pll",
+ CLK_SET_RATE_PARENT, 1, 1);
+ perfcl_pmux.pll = hws->hws[2];
+
+ hws->hws[3] = clk_hw_register_fixed_factor(dev, "pwrcl_pll_acd",
+ "pwrcl_pll",
+ CLK_SET_RATE_PARENT, 1, 1);
+ pwrcl_pmux.pll = hws->hws[3];
+
+ hws->num = 4;
for (i = 0; i < ARRAY_SIZE(clks); i++) {
ret = devm_clk_register_regmap(dev, clks[i]);
@@ -378,10 +412,65 @@ struct clk_hw_clks {
return ret;
}
+#define CPU_AFINITY_MASK 0xFFF
+#define PWRCL_CPU_REG_MASK 0x3
+#define PERFCL_CPU_REG_MASK 0x103
+
+/* ACD static settings (HMSS HPG 7.2.2) */
+#define L2ACDCR_REG 0x580ULL
+#define L2ACDTD_REG 0x581ULL
+#define L2ACDDVMRC_REG 0x584ULL
+#define L2ACDSSCR_REG 0x589ULL
+#define ACDTD_VAL 0x00006A11
+#define ACDCR_VAL 0x002C5FFD
+#define ACDSSCR_VAL 0x00000601
+#define ACDDVMRC_VAL 0x000E0F0F
+
+static DEFINE_SPINLOCK(acd_lock);
+
+static void qcom_cpu_clk_msm8996_acd_init(void)
+{
+ u64 hwid;
+ unsigned long flags;
+
+ spin_lock_irqsave(&acd_lock, flags);
+
+ hwid = read_cpuid_mpidr() & CPU_AFINITY_MASK;
+
+ /* Program ACD Tunable-Length Delay (TLD) */
+ set_l2_indirect_reg(L2ACDTD_REG, ACDTD_VAL);
+ /* Initial ACD for *this* cluster */
+ set_l2_indirect_reg(L2ACDDVMRC_REG, ACDDVMRC_VAL);
+ /* Program ACD soft start control bits. */
+ set_l2_indirect_reg(L2ACDSSCR_REG, ACDSSCR_VAL);
+
+ if (PWRCL_CPU_REG_MASK == (hwid | PWRCL_CPU_REG_MASK)) {
+ /* Enable Soft Stop/Start */
+ if (vbases[APC_BASE])
+ writel_relaxed(SSSCTL_VAL, vbases[APC_BASE] +
+ PWRCL_REG_OFFSET + SSSCTL_OFFSET);
+ /* Ensure SSSCTL config goes through before enabling ACD. */
+ mb();
+ /* Program ACD control bits */
+ set_l2_indirect_reg(L2ACDCR_REG, ACDCR_VAL);
+ }
+ if (PERFCL_CPU_REG_MASK == (hwid | PERFCL_CPU_REG_MASK)) { //else {
+ /* Program ACD control bits */
+ set_l2_indirect_reg(L2ACDCR_REG, ACDCR_VAL);
+ /* Enable Soft Stop/Start */
+ if (vbases[APC_BASE])
+ writel_relaxed(SSSCTL_VAL, vbases[APC_BASE] +
+ PERFCL_REG_OFFSET + SSSCTL_OFFSET);
+ /* Ensure SSSCTL config goes through before enabling ACD. */
+ mb();
+ }
+
+ spin_unlock_irqrestore(&acd_lock, flags);
+}
+
static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
{
int ret;
- void __iomem *base;
struct resource *res;
struct regmap *regmap_cpu;
struct clk_hw_clks *hws;
@@ -394,17 +483,17 @@ static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
if (!data)
return -ENOMEM;
- hws = devm_kzalloc(dev, sizeof(*hws) + 2 * sizeof(struct clk_hw *),
+ hws = devm_kzalloc(dev, sizeof(*hws) + 4 * sizeof(struct clk_hw *),
GFP_KERNEL);
if (!hws)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- base = devm_ioremap_resource(dev, res);
- if (IS_ERR(base))
- return PTR_ERR(base);
+ vbases[APC_BASE] = devm_ioremap_resource(dev, res);
+ if (IS_ERR(vbases[APC_BASE]))
+ return PTR_ERR(vbases[APC_BASE]);
- regmap_cpu = devm_regmap_init_mmio(dev, base,
+ regmap_cpu = devm_regmap_init_mmio(dev, vbases[APC_BASE],
&cpu_msm8996_regmap_config);
if (IS_ERR(regmap_cpu))
return PTR_ERR(regmap_cpu);
@@ -412,6 +501,7 @@ static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
ret = qcom_cpu_clk_msm8996_register_clks(dev, hws, regmap_cpu);
if (ret)
return ret;
+ qcom_cpu_clk_msm8996_acd_init();
data->hws[0] = &pwrcl_pmux.clkr.hw;
data->hws[1] = &perfcl_pmux.clkr.hw;
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 10/11] DT: QCOM: Add cpufreq-dt to msm8996
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
` (8 preceding siblings ...)
2018-01-04 11:10 ` [PATCH v2 09/11] clk: qcom: Add ACD path to CPU clock driver for msm8996 Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
2018-01-04 11:10 ` [PATCH v2 11/11] DT: QCOM: Add thermal mitigation " Ilia Lin
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
Add device tree frequency table for the MSM8996 to be
used by the upstream cpufreq-dt driver with the clk-cpu-8996
driver as infrastructure.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
arch/arm64/boot/dts/qcom/apq8096-db820c.dts | 2 +-
arch/arm64/boot/dts/qcom/msm8996.dtsi | 184 ++++++++++++++++++++++++++++
drivers/cpufreq/cpufreq-dt-platdev.c | 3 +
3 files changed, 188 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
index 230e9c8..da23bda 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
@@ -17,5 +17,5 @@
/ {
model = "Qualcomm Technologies, Inc. DB820c";
- compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc";
+ compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096";
};
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 4b2afcc..8beea7e 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -86,6 +86,8 @@
compatible = "qcom,kryo";
reg = <0x0 0x0>;
enable-method = "psci";
+ clocks = <&kryocc 0>;
+ operating-points-v2 = <&cluster0_opp>;
next-level-cache = <&L2_0>;
L2_0: l2-cache {
compatible = "cache";
@@ -98,6 +100,8 @@
compatible = "qcom,kryo";
reg = <0x0 0x1>;
enable-method = "psci";
+ clocks = <&kryocc 0>;
+ operating-points-v2 = <&cluster0_opp>;
next-level-cache = <&L2_0>;
};
@@ -106,6 +110,8 @@
compatible = "qcom,kryo";
reg = <0x0 0x100>;
enable-method = "psci";
+ clocks = <&kryocc 1>;
+ operating-points-v2 = <&cluster1_opp>;
next-level-cache = <&L2_1>;
L2_1: l2-cache {
compatible = "cache";
@@ -118,6 +124,8 @@
compatible = "qcom,kryo";
reg = <0x0 0x101>;
enable-method = "psci";
+ clocks = <&kryocc 1>;
+ operating-points-v2 = <&cluster1_opp>;
next-level-cache = <&L2_1>;
};
@@ -144,6 +152,182 @@
};
};
+ cluster0_opp: opp_table0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp at 307200000 {
+ opp-hz = /bits/ 64 < 307200000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 422400000 {
+ opp-hz = /bits/ 64 < 422400000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 480000000 {
+ opp-hz = /bits/ 64 < 480000000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 556800000 {
+ opp-hz = /bits/ 64 < 556800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 652800000 {
+ opp-hz = /bits/ 64 < 652800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 729600000 {
+ opp-hz = /bits/ 64 < 729600000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 844800000 {
+ opp-hz = /bits/ 64 < 844800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 960000000 {
+ opp-hz = /bits/ 64 < 960000000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1036800000 {
+ opp-hz = /bits/ 64 < 1036800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1113600000 {
+ opp-hz = /bits/ 64 < 1113600000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1190400000 {
+ opp-hz = /bits/ 64 < 1190400000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1228800000 {
+ opp-hz = /bits/ 64 < 1228800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1324800000 {
+ opp-hz = /bits/ 64 < 1324800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1401600000 {
+ opp-hz = /bits/ 64 < 1401600000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1478400000 {
+ opp-hz = /bits/ 64 < 1478400000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1593600000 {
+ opp-hz = /bits/ 64 < 1593600000 >;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+ cluster1_opp: opp_table1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp at 307200000 {
+ opp-hz = /bits/ 64 < 307200000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 403200000 {
+ opp-hz = /bits/ 64 < 403200000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 480000000 {
+ opp-hz = /bits/ 64 < 480000000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 556800000 {
+ opp-hz = /bits/ 64 < 556800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 652800000 {
+ opp-hz = /bits/ 64 < 652800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 729600000 {
+ opp-hz = /bits/ 64 < 729600000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 806400000 {
+ opp-hz = /bits/ 64 < 806400000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 883200000 {
+ opp-hz = /bits/ 64 < 883200000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 940800000 {
+ opp-hz = /bits/ 64 < 940800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1036800000 {
+ opp-hz = /bits/ 64 < 1036800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1113600000 {
+ opp-hz = /bits/ 64 < 1113600000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1190400000 {
+ opp-hz = /bits/ 64 < 1190400000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1248000000 {
+ opp-hz = /bits/ 64 < 1248000000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1324800000 {
+ opp-hz = /bits/ 64 < 1324800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1401600000 {
+ opp-hz = /bits/ 64 < 1401600000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1478400000 {
+ opp-hz = /bits/ 64 < 1478400000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1552000000 {
+ opp-hz = /bits/ 64 < 1552000000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1632000000 {
+ opp-hz = /bits/ 64 < 1632000000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1708800000 {
+ opp-hz = /bits/ 64 < 1708800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1785600000 {
+ opp-hz = /bits/ 64 < 1785600000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1824000000 {
+ opp-hz = /bits/ 64 < 1824000000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1920000000 {
+ opp-hz = /bits/ 64 < 1920000000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 1996800000 {
+ opp-hz = /bits/ 64 < 1996800000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 2073600000 {
+ opp-hz = /bits/ 64 < 2073600000 >;
+ clock-latency-ns = <200000>;
+ };
+ opp at 2150400000 {
+ opp-hz = /bits/ 64 < 2150400000 >;
+ clock-latency-ns = <200000>;
+ };
+
+ };
thermal-zones {
cpu-thermal0 {
polling-delay-passive = <250>;
diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index ecc56e2..0feca0e 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -95,6 +95,9 @@
{ .compatible = "xlnx,zynq-7000", },
{ .compatible = "xlnx,zynqmp", },
+ { .compatible = "qcom,msm8996", },
+ { .compatible = "qcom,apq8096", },
+
{ }
};
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v2 11/11] DT: QCOM: Add thermal mitigation to msm8996
2018-01-04 11:10 [PATCH v2 00/11] clk: qcom: CPU clock driver for msm8996 Ilia Lin
` (9 preceding siblings ...)
2018-01-04 11:10 ` [PATCH v2 10/11] DT: QCOM: Add cpufreq-dt to msm8996 Ilia Lin
@ 2018-01-04 11:10 ` Ilia Lin
10 siblings, 0 replies; 13+ messages in thread
From: Ilia Lin @ 2018-01-04 11:10 UTC (permalink / raw)
To: linux-arm-kernel
Add thermal mitigation configuration to msm8996.
With the cpufreq-dt OPP table the CPU frequency may be
scaled and therefore throttled by the thermal config.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 98 +++++++++++++++++++++++++++++++----
1 file changed, 87 insertions(+), 11 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 8beea7e..6fa061f 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -14,6 +14,7 @@
#include <dt-bindings/clock/qcom,gcc-msm8996.h>
#include <dt-bindings/clock/qcom,mmcc-msm8996.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/thermal/thermal.h>
/ {
model = "Qualcomm Technologies, Inc. MSM8996";
@@ -88,6 +89,10 @@
enable-method = "psci";
clocks = <&kryocc 0>;
operating-points-v2 = <&cluster0_opp>;
+ /* cooling options */
+ cooling-min-level = <0>;
+ cooling-max-level = <15>;
+ #cooling-cells = <2>;
next-level-cache = <&L2_0>;
L2_0: l2-cache {
compatible = "cache";
@@ -102,6 +107,10 @@
enable-method = "psci";
clocks = <&kryocc 0>;
operating-points-v2 = <&cluster0_opp>;
+ /* cooling options */
+ cooling-min-level = <0>;
+ cooling-max-level = <15>;
+ #cooling-cells = <2>;
next-level-cache = <&L2_0>;
};
@@ -112,6 +121,10 @@
enable-method = "psci";
clocks = <&kryocc 1>;
operating-points-v2 = <&cluster1_opp>;
+ /* cooling options */
+ cooling-min-level = <0>;
+ cooling-max-level = <15>;
+ #cooling-cells = <2>;
next-level-cache = <&L2_1>;
L2_1: l2-cache {
compatible = "cache";
@@ -126,6 +139,10 @@
enable-method = "psci";
clocks = <&kryocc 1>;
operating-points-v2 = <&cluster1_opp>;
+ /* cooling options */
+ cooling-min-level = <0>;
+ cooling-max-level = <15>;
+ #cooling-cells = <2>;
next-level-cache = <&L2_1>;
};
@@ -336,18 +353,33 @@
thermal-sensors = <&tsens0 3>;
trips {
- cpu_alert0: trip0 {
+ cpu_alert0: cpu_alert0 {
temperature = <75000>;
hysteresis = <2000>;
+ type = "active";
+ };
+ cpu_warn0: cpu_warn0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
type = "passive";
};
-
- cpu_crit0: trip1 {
+ cpu_crit0: cpu_crit0 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT 7>;
+ };
+ map1 {
+ trip = <&cpu_warn0>;
+ cooling-device = <&CPU0 8 THERMAL_NO_LIMIT>;
+ };
+ };
};
cpu-thermal1 {
@@ -357,18 +389,33 @@
thermal-sensors = <&tsens0 5>;
trips {
- cpu_alert1: trip0 {
+ cpu_alert1: cpu_alert1 {
temperature = <75000>;
hysteresis = <2000>;
+ type = "active";
+ };
+ cpu_warn1: cpu_warn1 {
+ temperature = <90000>;
+ hysteresis = <2000>;
type = "passive";
};
-
- cpu_crit1: trip1 {
+ cpu_crit1: cpu_crit1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert1>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT 7>;
+ };
+ map1 {
+ trip = <&cpu_warn1>;
+ cooling-device = <&CPU0 8 THERMAL_NO_LIMIT>;
+ };
+ };
};
cpu-thermal2 {
@@ -378,18 +425,32 @@
thermal-sensors = <&tsens0 8>;
trips {
- cpu_alert2: trip0 {
+ cpu_alert2: cpu_alert2 {
temperature = <75000>;
hysteresis = <2000>;
+ type = "active";
+ };
+ cpu_warn2: cpu_warn2 {
+ temperature = <90000>;
+ hysteresis = <2000>;
type = "passive";
};
-
- cpu_crit2: trip1 {
+ cpu_crit2: cpu_crit2 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert2>;
+ cooling-device = <&CPU2 THERMAL_NO_LIMIT 7>;
+ };
+ map1 {
+ trip = <&cpu_warn2>;
+ cooling-device = <&CPU2 8 THERMAL_NO_LIMIT>;
+ };
+ };
};
cpu-thermal3 {
@@ -399,18 +460,33 @@
thermal-sensors = <&tsens0 10>;
trips {
- cpu_alert3: trip0 {
+ cpu_alert3: cpu_alert3 {
temperature = <75000>;
hysteresis = <2000>;
+ type = "active";
+ };
+ cpu_warn3: cpu_warn3 {
+ temperature = <90000>;
+ hysteresis = <2000>;
type = "passive";
};
-
cpu_crit3: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert3>;
+ cooling-device = <&CPU2 THERMAL_NO_LIMIT 7>;
+ };
+ map1 {
+ trip = <&cpu_warn3>;
+ cooling-device = <&CPU2 8 THERMAL_NO_LIMIT>;
+ };
+ };
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 13+ messages in thread