From: t-kristo@ti.com (Tero Kristo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 5/5] clk: ti: add support for clock latching to mux clocks
Date: Thu, 15 Feb 2018 14:49:51 +0200 [thread overview]
Message-ID: <1518698991-10099-6-git-send-email-t-kristo@ti.com> (raw)
In-Reply-To: <1518698991-10099-1-git-send-email-t-kristo@ti.com>
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the mux clock.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
---
drivers/clk/ti/clock.h | 1 +
drivers/clk/ti/mux.c | 13 ++++++++++---
2 files changed, 11 insertions(+), 3 deletions(-)
diff --git a/drivers/clk/ti/clock.h b/drivers/clk/ti/clock.h
index 62b108c..90b86aa 100644
--- a/drivers/clk/ti/clock.h
+++ b/drivers/clk/ti/clock.h
@@ -34,6 +34,7 @@ struct clk_omap_mux {
u32 *table;
u32 mask;
u8 shift;
+ s8 latch;
u8 flags;
};
diff --git a/drivers/clk/ti/mux.c b/drivers/clk/ti/mux.c
index d470580..69a4308 100644
--- a/drivers/clk/ti/mux.c
+++ b/drivers/clk/ti/mux.c
@@ -86,6 +86,7 @@ static int ti_clk_mux_set_parent(struct clk_hw *hw, u8 index)
}
val |= index << mux->shift;
ti_clk_ll_ops->clk_writel(val, &mux->reg);
+ ti_clk_latch(&mux->reg, mux->latch);
return 0;
}
@@ -100,7 +101,7 @@ static struct clk *_register_mux(struct device *dev, const char *name,
const char * const *parent_names,
u8 num_parents, unsigned long flags,
struct clk_omap_reg *reg, u8 shift, u32 mask,
- u8 clk_mux_flags, u32 *table)
+ s8 latch, u8 clk_mux_flags, u32 *table)
{
struct clk_omap_mux *mux;
struct clk *clk;
@@ -121,6 +122,7 @@ static struct clk *_register_mux(struct device *dev, const char *name,
memcpy(&mux->reg, reg, sizeof(*reg));
mux->shift = shift;
mux->mask = mask;
+ mux->latch = latch;
mux->flags = clk_mux_flags;
mux->table = table;
mux->hw.init = &init;
@@ -160,7 +162,7 @@ struct clk *ti_clk_register_mux(struct ti_clk *setup)
flags |= CLK_SET_RATE_PARENT;
return _register_mux(NULL, setup->name, mux->parents, mux->num_parents,
- flags, ®, mux->bit_shift, mask,
+ flags, ®, mux->bit_shift, mask, -EINVAL,
mux_flags, NULL);
}
@@ -179,6 +181,7 @@ static void of_mux_clk_setup(struct device_node *node)
u8 clk_mux_flags = 0;
u32 mask = 0;
u32 shift = 0;
+ s32 latch = -EINVAL;
u32 flags = CLK_SET_RATE_NO_REPARENT;
num_parents = of_clk_get_parent_count(node);
@@ -197,6 +200,8 @@ static void of_mux_clk_setup(struct device_node *node)
of_property_read_u32(node, "ti,bit-shift", &shift);
+ of_property_read_u32(node, "ti,latch-bit", &latch);
+
if (of_property_read_bool(node, "ti,index-starts-at-one"))
clk_mux_flags |= CLK_MUX_INDEX_ONE;
@@ -211,7 +216,8 @@ static void of_mux_clk_setup(struct device_node *node)
mask = (1 << fls(mask)) - 1;
clk = _register_mux(NULL, node->name, parent_names, num_parents,
- flags, ®, shift, mask, clk_mux_flags, NULL);
+ flags, ®, shift, mask, latch, clk_mux_flags,
+ NULL);
if (!IS_ERR(clk))
of_clk_add_provider(node, of_clk_src_simple_get, clk);
@@ -234,6 +240,7 @@ struct clk_hw *ti_clk_build_component_mux(struct ti_clk_mux *setup)
return ERR_PTR(-ENOMEM);
mux->shift = setup->bit_shift;
+ mux->latch = -EINVAL;
mux->reg.index = setup->module;
mux->reg.offset = setup->reg;
--
1.9.1
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
prev parent reply other threads:[~2018-02-15 12:49 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-15 12:49 [PATCH 0/5] clk: ti: add support for dra76x latched clocks Tero Kristo
2018-02-15 12:49 ` [PATCH 1/5] dt-bindings: clock: ti: add latching support to mux and divider clocks Tero Kristo
2018-02-19 14:36 ` Rob Herring
2018-02-15 12:49 ` [PATCH 2/5] clk: ti: add support for register read-modify-write low-level operation Tero Kristo
2018-02-15 12:49 ` [PATCH 3/5] clk: ti: add generic support for clock latching Tero Kristo
2018-02-15 12:49 ` [PATCH 4/5] clk: ti: add support for clock latching to divider clocks Tero Kristo
2018-02-15 12:49 ` Tero Kristo [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1518698991-10099-6-git-send-email-t-kristo@ti.com \
--to=t-kristo@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox