From mboxrd@z Thu Jan  1 00:00:00 1970
From: laurent.pinchart@ideasonboard.com (Laurent Pinchart)
Date: Tue, 12 Mar 2013 14:24:15 +0100
Subject: [PATCH v6 1/3] serial: sh-sci: Add OF support
In-Reply-To: <20130312082038.GC3553@linux-sh.org>
References: <1362569437-11133-1-git-send-email-hechtb+renesas@gmail.com>
 <1689352.QAdqes1IG8@avalon> <20130312082038.GC3553@linux-sh.org>
Message-ID: <1527167.zrgCvGiAzu@avalon>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Hi Paul,

On Tuesday 12 March 2013 17:20:39 Paul Mundt wrote:
> On Mon, Mar 11, 2013 at 11:32:31PM +0100, Laurent Pinchart wrote:
> > On Thursday 07 March 2013 11:26:29 Bastian Hecht wrote:
> > > >> +- renesas,scscr : Should contain a bitfield used by the Serial
> > > >> Control
> > > >> Register.
> > > >> +  b7 = SCSCR_TIE
> > > >> +  b6 = SCSCR_RIE
> > > >> +  b5 = SCSCR_TE
> > > >> +  b4 = SCSCR_RE
> > > >> +  b3 = SCSCR_REIE
> > > >> +  b2 = SCSCR_TOIE
> > > >> +  b1 = SCSCR_CKE1
> > > >> +  b0 = SCSCR_CKE0
> > > > 
> > > > What is that for exactly ?
> > > 
> > > What I can see from 3 different datasheets (sh7372, sh73a0, r8a7740)
> > > the first 2 bits differ in meaning.
> > > 
> > > On r8a7740 it depends: In asynchronous mode the first 2 bits CKE0/1
> > > define whether you want to use an external clock to drive the baud
> > > generator or if you want to use the internal SUB clock. If you use the
> > > SUB clock you can further define if you want to use a subscaled SUB
> > > clock in the SCSMR register. In synchronous mode you must rely on the
> > > internal clock for the baud generator and can select if the SCK pin is
> > > used as clock input or output.
> > 
> > What about adding an optional source clock property to the bindings, that
> > would contain the phandle of the source clock ? If the property is absent
> > then the internal clock would be used.
> 
> We can't really use the internal oscillator at the moment, it's one of
> the things that is blocked on adoption of the common struct clk work. The
> baud rate generator algo will likewise differ depending on whether it's
> using an internally generated clock or not, which also makes a different
> set of baud rates available.
> 
> My plan originally was to wait until the common struct clk stuff came
> along well enough that we could provide a clock dynamically depending on
> the target baud (or for avoiding cpufreq pre/post-change notifier
> chains), but this obviously hasn't happened yet.
> 
> I think your idea for the abstraction with the phandle sounds like the
> right approach, but we aren't presently in a state where we can handle
> that.

Do the platforms that will be converted to DT currently need to make the clock 
source configurable ? If not we could just leave it out of the DT bindings 
until needed. Hopefully by then we'll have a common clock framework 
implementation.

> > > Bit 2 and 3 don't exist in my datasheets.
> > > 
> > > The other bits define under which conditions you receive interrupts
> > > (send FIFO empty, receive FIFO full) and which bits you need to start
> > > transfers (one bit to start sending, one receiving). The bits 8 to 31
> > > are used to set up DMA transfers and various interrupt events like
> > > error status and finish transfers. I haven't included them as they are
> > > not used in the driver.
> > 
> > If they're not used maybe we can drop them :-)
> 
> Obviously they're used, otherwise they wouldn't be defined in the common
> header. Whether they are used by these specific CPUs or not isn't
> relevant, as there are plenty of cases where they are. grep harder.

My point is that if they're only used by arm/sh/* SoCs we don't need to 
support them in DT.

-- 
Regards,

Laurent Pinchart