[RFC PATCH] of: make MAX_RESERVED_REGIONS configurable

Miles Chen
2018-11-28T01:56:04Z

On Mon, 2018-11-26 at 09:33 +0800, Miles Chen wrote:
> On Sat, 2018-11-24 at 14:56 -0600, Rob Herring wrote:
> > On Wed, Nov 21, 2018 at 8:51 PM Miles Chen <miles.chen@mediatek.com> wrote:
> > >
> > > On Wed, 2018-11-21 at 10:39 -0600, Rob Herring wrote:
> > > > On Wed, Nov 21, 2018 at 2:11 AM <miles.chen@mediatek.com> wrote:
> > > > >
> > > > > From: Miles Chen <miles.chen@mediatek.com>
> > > > >
> > > > > When we use more than 32 entries in /resered-memory,
> > > > > there will be an error message: "not enough space all defined regions.".
> > > > > We can increase MAX_RESERVED_REGIONS to fix this.
> > > > >
> > > > > commit 22f8cc6e3373 ("drivers: of: increase MAX_RESERVED_REGIONS to 32")
> > > > > increased MAX_RESERVED_REGIONS to 32 but I'm not sure if increasing
> > > > > MAX_RESERVED_REGIONS to 64 is suitable for everyone.
> > > > >
> > > > > In this RFC patch, CONFIG_MAX_OF_RESERVED_REGIONS is added and used as
> > > > > MAX_RESERVED_REGIONS. Add a sanity test to make sure that
> > > > > MAX_RESERVED_REGIONS is less than INIT_MEMBLOCK_REGIONS.
> > > > > Users can configure CONFIG_MAX_OF_RESERVED_REGIONS according to their
> > > > > need.
> > > >
> > > > I don't want a kconfig option for this. I think it should be dynamic instead.
> > > >
> > > > The current flow is like this:
> > > >
> > > > for each reserved node:
> > > > - call memblock_reserve
> > > > - Add info to reserved_mem array
> > > >
> > > > I think we should change it to:
> > > >
> > > > for each reserved node:
> > > > - call memblock_reserve
> > > > - count number of nodes
> > > >
> > > > Alloc array using memblock_alloc
> > > >
> > > > for each reserved node:
> > > > - Add info to reserved_mem array
> > > >
> > >
> > > thanks for your comment.
> > >
> > > I reviewed the flow and it might be easier to count the
> > > nodes and setup array first:
> > >
> > > for each reserved node:
> > > - count number of nodes
> > >
> > > Alloc array using memblock_alloc
> > >
> > >
> > > for each reserved node:
> > > - call memblock_reserve
> >
> > The order here is wrong. It is important that you reserve the memory
> > blocks before doing any allocations.
>
> thanks for pointing that out. You are right. I'll follow your
> suggestion.

I got a problem while implementing this change: the array allocation
is done successfully but the kernel does not create mappings for it yet,
so the array is not accessible. (kernel will create the mapping later in
paging_init())

For example: aarch64 setup_arch()
setup_arch()
{
memblock_init(); /* early_init_fdt_scan_reserved_mem() is called */
paging_init();
}

Could you give me some advice, please?

Miles
>
> >
> > > - Add info to reserved_mem array
> > >
> > > What do you think?
> > >
> > > > Rob
> > >
> > >
>
>