[PATCH v5 0/2] add uart DMA function

[PATCH v5 0/2] add uart DMA function

[Long Cheng]

In Mediatek SOCs, the uart can support DMA function.
Base on DMA engine formwork, we add the DMA code to support uart. And put the code under drivers/dma.

This series contains document bindings, Kconfig to control the function enable or not,
device tree including interrupt and dma device node, the code of UART DM

Changes compared to v4:
-modify Kconfig depends on.
Changes compared to v3:
-fix CONFIG_PM, will cause build fail
Changes compared to v2:
-remove unimportant parameters
-instead of cookie, use APIs of virtual channel.
-use of_dma_xlate_by_chan_id.
Changes compared to v1:
-mian revised file, 8250_mtk_dma.c
--parameters renamed for standard
--remove atomic operation

Long Cheng (2):
  dmaengine: 8250_mtk_dma: add Mediatek uart DMA support
  arm: dts: mt2712: add uart APDMA to device tree

 arch/arm64/boot/dts/mediatek/mt2712e.dtsi |   50 ++
 drivers/dma/mediatek/8250_mtk_dma.c       |  830 +++++++++++++++++++++++++++++
 drivers/dma/mediatek/Kconfig              |   11 +
 drivers/dma/mediatek/Makefile             |    1 +
 4 files changed, 892 insertions(+)
 create mode 100644 drivers/dma/mediatek/8250_mtk_dma.c

-- 
1.7.9.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 1/2] dmaengine: 8250_mtk_dma: add Mediatek uart DMA support

[Long Cheng]

In DMA engine framework, add 8250 mtk dma to support it.

Signed-off-by: Long Cheng <long.cheng@mediatek.com>
---
 drivers/dma/mediatek/8250_mtk_dma.c |  830 +++++++++++++++++++++++++++++++++++
 drivers/dma/mediatek/Kconfig        |   11 +
 drivers/dma/mediatek/Makefile       |    1 +
 3 files changed, 842 insertions(+)
 create mode 100644 drivers/dma/mediatek/8250_mtk_dma.c

diff --git a/drivers/dma/mediatek/8250_mtk_dma.c b/drivers/dma/mediatek/8250_mtk_dma.c
new file mode 100644
index 0000000..f79d180
--- /dev/null
+++ b/drivers/dma/mediatek/8250_mtk_dma.c
@@ -0,0 +1,830 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Mediatek 8250 DMA driver.
+ *
+ * Copyright (c) 2018 MediaTek Inc.
+ * Author: Long Cheng <long.cheng@mediatek.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_dma.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/pm_runtime.h>
+#include <linux/iopoll.h>
+
+#include "../virt-dma.h"
+
+#define MTK_APDMA_DEFAULT_REQUESTS	127
+#define MTK_APDMA_CHANNELS		(CONFIG_SERIAL_8250_NR_UARTS * 2)
+
+#define VFF_EN_B		BIT(0)
+#define VFF_STOP_B		BIT(0)
+#define VFF_FLUSH_B		BIT(0)
+#define VFF_4G_SUPPORT_B	BIT(0)
+#define VFF_RX_INT_EN0_B	BIT(0)	/*rx valid size >=  vff thre*/
+#define VFF_RX_INT_EN1_B	BIT(1)
+#define VFF_TX_INT_EN_B		BIT(0)	/*tx left size >= vff thre*/
+#define VFF_WARM_RST_B		BIT(0)
+#define VFF_RX_INT_FLAG_CLR_B	(BIT(0) | BIT(1))
+#define VFF_TX_INT_FLAG_CLR_B	0
+#define VFF_STOP_CLR_B		0
+#define VFF_FLUSH_CLR_B		0
+#define VFF_INT_EN_CLR_B	0
+#define VFF_4G_SUPPORT_CLR_B	0
+
+/* interrupt trigger level for tx */
+#define VFF_TX_THRE(n)		((n) * 7 / 8)
+/* interrupt trigger level for rx */
+#define VFF_RX_THRE(n)		((n) * 3 / 4)
+
+#define MTK_DMA_RING_SIZE	0xffffU
+/* invert this bit when wrap ring head again*/
+#define MTK_DMA_RING_WRAP	0x10000U
+
+#define VFF_INT_FLAG		0x00
+#define VFF_INT_EN		0x04
+#define VFF_EN			0x08
+#define VFF_RST			0x0c
+#define VFF_STOP		0x10
+#define VFF_FLUSH		0x14
+#define VFF_ADDR		0x1c
+#define VFF_LEN			0x24
+#define VFF_THRE		0x28
+#define VFF_WPT			0x2c
+#define VFF_RPT			0x30
+/*TX: the buffer size HW can read. RX: the buffer size SW can read.*/
+#define VFF_VALID_SIZE		0x3c
+/*TX: the buffer size SW can write. RX: the buffer size HW can write.*/
+#define VFF_LEFT_SIZE		0x40
+#define VFF_DEBUG_STATUS	0x50
+#define VFF_4G_SUPPORT		0x54
+
+struct mtk_dmadev {
+	struct dma_device ddev;
+	void __iomem *mem_base[MTK_APDMA_CHANNELS];
+	spinlock_t lock; /* dma dev lock */
+	struct tasklet_struct task;
+	struct list_head pending;
+	struct clk *clk;
+	unsigned int dma_requests;
+	bool support_33bits;
+	unsigned int dma_irq[MTK_APDMA_CHANNELS];
+	struct mtk_chan *ch[MTK_APDMA_CHANNELS];
+};
+
+struct mtk_chan {
+	struct virt_dma_chan vc;
+	struct list_head node;
+	struct dma_slave_config	cfg;
+	void __iomem *base;
+	struct mtk_dma_desc *desc;
+
+	bool stop;
+	bool requested;
+
+	unsigned int rx_status;
+};
+
+struct mtk_dma_sg {
+	dma_addr_t addr;
+	unsigned int en;		/* number of elements (24-bit) */
+	unsigned int fn;		/* number of frames (16-bit) */
+};
+
+struct mtk_dma_desc {
+	struct virt_dma_desc vd;
+	enum dma_transfer_direction dir;
+
+	unsigned int sglen;
+	struct mtk_dma_sg sg[0];
+
+	unsigned int len;
+};
+
+static inline struct mtk_dmadev *to_mtk_dma_dev(struct dma_device *d)
+{
+	return container_of(d, struct mtk_dmadev, ddev);
+}
+
+static inline struct mtk_chan *to_mtk_dma_chan(struct dma_chan *c)
+{
+	return container_of(c, struct mtk_chan, vc.chan);
+}
+
+static inline struct mtk_dma_desc *to_mtk_dma_desc
+	(struct dma_async_tx_descriptor *t)
+{
+	return container_of(t, struct mtk_dma_desc, vd.tx);
+}
+
+static void mtk_dma_chan_write(struct mtk_chan *c,
+			       unsigned int reg, unsigned int val)
+{
+	writel(val, c->base + reg);
+}
+
+static unsigned int mtk_dma_chan_read(struct mtk_chan *c, unsigned int reg)
+{
+	return readl(c->base + reg);
+}
+
+static void mtk_dma_desc_free(struct virt_dma_desc *vd)
+{
+	struct dma_chan *chan = vd->tx.chan;
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+
+	kfree(c->desc);
+	c->desc = NULL;
+}
+
+static void mtk_dma_tx_flush(struct dma_chan *chan)
+{
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+
+	if (mtk_dma_chan_read(c, VFF_FLUSH) == 0U)
+		mtk_dma_chan_write(c, VFF_FLUSH, VFF_FLUSH_B);
+}
+
+static void mtk_dma_tx_write(struct dma_chan *chan)
+{
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	unsigned int txcount = c->desc->len;
+	unsigned int len, send, left, wpt, wrap;
+
+	len = mtk_dma_chan_read(c, VFF_LEN);
+
+	while ((left = mtk_dma_chan_read(c, VFF_LEFT_SIZE)) > 0U) {
+		if (c->desc->len == 0U)
+			break;
+		send = min_t(unsigned int, left, c->desc->len);
+		wpt = mtk_dma_chan_read(c, VFF_WPT);
+		wrap = wpt & MTK_DMA_RING_WRAP ? 0U : MTK_DMA_RING_WRAP;
+
+		if ((wpt & (len - 1U)) + send < len)
+			mtk_dma_chan_write(c, VFF_WPT, wpt + send);
+		else
+			mtk_dma_chan_write(c, VFF_WPT,
+					   ((wpt + send) & (len - 1U))
+					   | wrap);
+
+		c->desc->len -= send;
+	}
+
+	if (txcount != c->desc->len) {
+		mtk_dma_chan_write(c, VFF_INT_EN, VFF_TX_INT_EN_B);
+		mtk_dma_tx_flush(chan);
+	}
+}
+
+static void mtk_dma_start_tx(struct mtk_chan *c)
+{
+	if (mtk_dma_chan_read(c, VFF_LEFT_SIZE) == 0U)
+		mtk_dma_chan_write(c, VFF_INT_EN, VFF_TX_INT_EN_B);
+	else
+		mtk_dma_tx_write(&c->vc.chan);
+
+	c->stop = false;
+}
+
+static void mtk_dma_get_rx_size(struct mtk_chan *c)
+{
+	unsigned int rx_size = mtk_dma_chan_read(c, VFF_LEN);
+	unsigned int rdptr, wrptr, wrreg, rdreg, count;
+
+	rdreg = mtk_dma_chan_read(c, VFF_RPT);
+	wrreg = mtk_dma_chan_read(c, VFF_WPT);
+	rdptr = rdreg & MTK_DMA_RING_SIZE;
+	wrptr = wrreg & MTK_DMA_RING_SIZE;
+	count = ((rdreg ^ wrreg) & MTK_DMA_RING_WRAP) ?
+			(wrptr + rx_size - rdptr) : (wrptr - rdptr);
+
+	c->rx_status = count;
+
+	mtk_dma_chan_write(c, VFF_RPT, wrreg);
+}
+
+static void mtk_dma_start_rx(struct mtk_chan *c)
+{
+	struct dma_chan *chan = &c->vc.chan;
+	struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
+	struct mtk_dma_desc *d = c->desc;
+
+	if (mtk_dma_chan_read(c, VFF_VALID_SIZE) == 0U)
+		return;
+
+	if (d && vchan_next_desc(&c->vc)) {
+		mtk_dma_get_rx_size(c);
+		list_del(&d->vd.node);
+		vchan_cookie_complete(&d->vd);
+	} else {
+		spin_lock(&mtkd->lock);
+		if (list_empty(&mtkd->pending))
+			list_add_tail(&c->node, &mtkd->pending);
+		spin_unlock(&mtkd->lock);
+		tasklet_schedule(&mtkd->task);
+	}
+}
+
+static void mtk_dma_reset(struct mtk_chan *c)
+{
+	struct mtk_dmadev *mtkd = to_mtk_dma_dev(c->vc.chan.device);
+	u32 status;
+	int ret;
+
+	mtk_dma_chan_write(c, VFF_ADDR, 0);
+	mtk_dma_chan_write(c, VFF_THRE, 0);
+	mtk_dma_chan_write(c, VFF_LEN, 0);
+	mtk_dma_chan_write(c, VFF_RST, VFF_WARM_RST_B);
+
+	ret = readx_poll_timeout(readl,
+				 c->base + VFF_EN,
+				 status, status == 0, 10, 100);
+	if (ret) {
+		dev_err(c->vc.chan.device->dev,
+				"dma reset: fail, timeout\n");
+		return;
+	}
+
+	if (c->cfg.direction == DMA_DEV_TO_MEM)
+		mtk_dma_chan_write(c, VFF_RPT, 0);
+	else if (c->cfg.direction == DMA_MEM_TO_DEV)
+		mtk_dma_chan_write(c, VFF_WPT, 0);
+
+	if (mtkd->support_33bits)
+		mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_CLR_B);
+}
+
+static void mtk_dma_stop(struct mtk_chan *c)
+{
+	u32 status;
+	int ret;
+
+	mtk_dma_chan_write(c, VFF_FLUSH, VFF_FLUSH_CLR_B);
+	/* Wait for flush */
+	ret = readx_poll_timeout(readl,
+				 c->base + VFF_FLUSH,
+				 status,
+				 (status & VFF_FLUSH_B) != VFF_FLUSH_B,
+				 10, 100);
+	if (ret)
+		dev_err(c->vc.chan.device->dev,
+			"dma stop: polling FLUSH fail, DEBUG=0x%x\n",
+			mtk_dma_chan_read(c, VFF_DEBUG_STATUS));
+
+	/*set stop as 1 -> wait until en is 0 -> set stop as 0*/
+	mtk_dma_chan_write(c, VFF_STOP, VFF_STOP_B);
+	ret = readx_poll_timeout(readl,
+				 c->base + VFF_EN,
+				 status, status == 0, 10, 100);
+	if (ret)
+		dev_err(c->vc.chan.device->dev,
+			"dma stop: polling VFF_EN fail, DEBUG=0x%x\n",
+			mtk_dma_chan_read(c, VFF_DEBUG_STATUS));
+
+	mtk_dma_chan_write(c, VFF_STOP, VFF_STOP_CLR_B);
+	mtk_dma_chan_write(c, VFF_INT_EN, VFF_INT_EN_CLR_B);
+
+	if (c->cfg.direction == DMA_DEV_TO_MEM)
+		mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
+	else
+		mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
+
+	c->stop = true;
+}
+
+/*
+ * This callback schedules all pending channels. We could be more
+ * clever here by postponing allocation of the real DMA channels to
+ * this point, and freeing them when our virtual channel becomes idle.
+ *
+ * We would then need to deal with 'all channels in-use'
+ */
+static void mtk_dma_sched(unsigned long data)
+{
+	struct mtk_dmadev *mtkd = (struct mtk_dmadev *)data;
+	struct virt_dma_desc *vd;
+	struct mtk_chan *c;
+	unsigned long flags;
+	LIST_HEAD(head);
+
+	spin_lock_irq(&mtkd->lock);
+	list_splice_tail_init(&mtkd->pending, &head);
+	spin_unlock_irq(&mtkd->lock);
+
+	if (!list_empty(&head)) {
+		c = list_first_entry(&head, struct mtk_chan, node);
+
+		spin_lock_irqsave(&c->vc.lock, flags);
+		if (c->cfg.direction == DMA_DEV_TO_MEM) {
+			list_del_init(&c->node);
+			mtk_dma_start_rx(c);
+		} else if (c->cfg.direction == DMA_MEM_TO_DEV) {
+			vd = vchan_next_desc(&c->vc);
+			c->desc = to_mtk_dma_desc(&vd->tx);
+			list_del_init(&c->node);
+			mtk_dma_start_tx(c);
+		}
+		spin_unlock_irqrestore(&c->vc.lock, flags);
+	}
+}
+
+static int mtk_dma_alloc_chan_resources(struct dma_chan *chan)
+{
+	struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	int ret = -EBUSY;
+
+	pm_runtime_get_sync(mtkd->ddev.dev);
+
+	if (!mtkd->ch[chan->chan_id]) {
+		c->base = mtkd->mem_base[chan->chan_id];
+		mtkd->ch[chan->chan_id] = c;
+		ret = 1;
+	}
+	c->requested = false;
+	mtk_dma_reset(c);
+
+	return ret;
+}
+
+static void mtk_dma_free_chan_resources(struct dma_chan *chan)
+{
+	struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+
+	if (c->requested) {
+		c->requested = false;
+		free_irq(mtkd->dma_irq[chan->chan_id], chan);
+	}
+
+	tasklet_kill(&mtkd->task);
+	tasklet_kill(&c->vc.task);
+
+	c->base = NULL;
+	mtkd->ch[chan->chan_id] = NULL;
+	vchan_free_chan_resources(&c->vc);
+
+	pm_runtime_put_sync(mtkd->ddev.dev);
+}
+
+static enum dma_status mtk_dma_tx_status(struct dma_chan *chan,
+					 dma_cookie_t cookie,
+					 struct dma_tx_state *txstate)
+{
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	enum dma_status ret;
+	unsigned long flags;
+
+	if (!txstate)
+		return DMA_ERROR;
+
+	ret = dma_cookie_status(chan, cookie, txstate);
+	spin_lock_irqsave(&c->vc.lock, flags);
+	if (ret == DMA_IN_PROGRESS) {
+		c->rx_status = mtk_dma_chan_read(c, VFF_RPT)
+			     & MTK_DMA_RING_SIZE;
+		dma_set_residue(txstate, c->rx_status);
+	} else if (ret == DMA_COMPLETE && c->cfg.direction == DMA_DEV_TO_MEM) {
+		dma_set_residue(txstate, c->rx_status);
+	} else {
+		dma_set_residue(txstate, 0);
+	}
+	spin_unlock_irqrestore(&c->vc.lock, flags);
+
+	return ret;
+}
+
+static struct dma_async_tx_descriptor *mtk_dma_prep_slave_sg
+	(struct dma_chan *chan, struct scatterlist *sgl,
+	unsigned int sglen,	enum dma_transfer_direction dir,
+	unsigned long tx_flags, void *context)
+{
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	struct scatterlist *sgent;
+	struct mtk_dma_desc *d;
+	struct mtk_dma_sg *sg;
+	unsigned int size, i, j, en;
+
+	en = 1;
+
+	if ((dir != DMA_DEV_TO_MEM) &&
+		(dir != DMA_MEM_TO_DEV)) {
+		dev_err(chan->device->dev, "bad direction\n");
+		return NULL;
+	}
+
+	/* Now allocate and setup the descriptor. */
+	d = kzalloc(sizeof(*d) + sglen * sizeof(d->sg[0]), GFP_ATOMIC);
+	if (!d)
+		return NULL;
+
+	d->dir = dir;
+
+	j = 0;
+	for_each_sg(sgl, sgent, sglen, i) {
+		d->sg[j].addr = sg_dma_address(sgent);
+		d->sg[j].en = en;
+		d->sg[j].fn = sg_dma_len(sgent) / en;
+		j++;
+	}
+
+	d->sglen = j;
+
+	if (dir == DMA_MEM_TO_DEV) {
+		for (size = i = 0; i < d->sglen; i++) {
+			sg = &d->sg[i];
+			size += sg->en * sg->fn;
+		}
+		d->len = size;
+	}
+
+	return vchan_tx_prep(&c->vc, &d->vd, tx_flags);
+}
+
+static void mtk_dma_issue_pending(struct dma_chan *chan)
+{
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	struct virt_dma_desc *vd;
+	struct mtk_dmadev *mtkd;
+	unsigned long flags;
+
+	spin_lock_irqsave(&c->vc.lock, flags);
+	if (c->cfg.direction == DMA_DEV_TO_MEM) {
+		mtkd = to_mtk_dma_dev(chan->device);
+		if (vchan_issue_pending(&c->vc) && !c->desc) {
+			vd = vchan_next_desc(&c->vc);
+			c->desc = to_mtk_dma_desc(&vd->tx);
+		}
+	} else if (c->cfg.direction == DMA_MEM_TO_DEV) {
+		if (vchan_issue_pending(&c->vc) && !c->desc) {
+			vd = vchan_next_desc(&c->vc);
+			c->desc = to_mtk_dma_desc(&vd->tx);
+			mtk_dma_start_tx(c);
+		}
+	}
+	spin_unlock_irqrestore(&c->vc.lock, flags);
+}
+
+static irqreturn_t mtk_dma_rx_interrupt(int irq, void *dev_id)
+{
+	struct dma_chan *chan = (struct dma_chan *)dev_id;
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	unsigned long flags;
+
+	spin_lock_irqsave(&c->vc.lock, flags);
+	mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
+
+	mtk_dma_start_rx(c);
+
+	spin_unlock_irqrestore(&c->vc.lock, flags);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mtk_dma_tx_interrupt(int irq, void *dev_id)
+{
+	struct dma_chan *chan = (struct dma_chan *)dev_id;
+	struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	struct mtk_dma_desc *d = c->desc;
+	unsigned long flags;
+
+	spin_lock_irqsave(&c->vc.lock, flags);
+	if (d->len != 0U) {
+		list_add_tail(&c->node, &mtkd->pending);
+		tasklet_schedule(&mtkd->task);
+	} else {
+		list_del(&d->vd.node);
+		vchan_cookie_complete(&d->vd);
+	}
+	spin_unlock_irqrestore(&c->vc.lock, flags);
+
+	mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
+
+	return IRQ_HANDLED;
+}
+
+static int mtk_dma_slave_config(struct dma_chan *chan,
+				struct dma_slave_config *cfg)
+{
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	struct mtk_dmadev *mtkd = to_mtk_dma_dev(c->vc.chan.device);
+	int ret;
+
+	c->cfg = *cfg;
+
+	if (cfg->direction == DMA_DEV_TO_MEM) {
+		unsigned int rx_len = cfg->src_addr_width * 1024;
+
+		mtk_dma_chan_write(c, VFF_ADDR, cfg->src_addr);
+		mtk_dma_chan_write(c, VFF_LEN, rx_len);
+		mtk_dma_chan_write(c, VFF_THRE, VFF_RX_THRE(rx_len));
+		mtk_dma_chan_write(c,
+				   VFF_INT_EN, VFF_RX_INT_EN0_B
+				   | VFF_RX_INT_EN1_B);
+		mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
+		mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
+
+		if (!c->requested) {
+			c->requested = true;
+			ret = request_irq(mtkd->dma_irq[chan->chan_id],
+					  mtk_dma_rx_interrupt,
+					  IRQF_TRIGGER_NONE,
+					  KBUILD_MODNAME, chan);
+			if (ret < 0) {
+				dev_err(chan->device->dev, "Can't request rx dma IRQ\n");
+				return -EINVAL;
+			}
+		}
+	} else if (cfg->direction == DMA_MEM_TO_DEV)	{
+		unsigned int tx_len = cfg->dst_addr_width * 1024;
+
+		mtk_dma_chan_write(c, VFF_ADDR, cfg->dst_addr);
+		mtk_dma_chan_write(c, VFF_LEN, tx_len);
+		mtk_dma_chan_write(c, VFF_THRE, VFF_TX_THRE(tx_len));
+		mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
+		mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
+
+		if (!c->requested) {
+			c->requested = true;
+			ret = request_irq(mtkd->dma_irq[chan->chan_id],
+					  mtk_dma_tx_interrupt,
+					  IRQF_TRIGGER_NONE,
+					  KBUILD_MODNAME, chan);
+			if (ret < 0) {
+				dev_err(chan->device->dev, "Can't request tx dma IRQ\n");
+				return -EINVAL;
+			}
+		}
+	}
+
+	if (mtkd->support_33bits)
+		mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_B);
+
+	if (mtk_dma_chan_read(c, VFF_EN) != VFF_EN_B) {
+		dev_err(chan->device->dev,
+			"config dma dir[%d] fail\n", cfg->direction);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int mtk_dma_terminate_all(struct dma_chan *chan)
+{
+	struct mtk_chan *c = to_mtk_dma_chan(chan);
+	unsigned long flags;
+
+	spin_lock_irqsave(&c->vc.lock, flags);
+	list_del_init(&c->node);
+	mtk_dma_stop(c);
+	spin_unlock_irqrestore(&c->vc.lock, flags);
+
+	return 0;
+}
+
+static int mtk_dma_device_pause(struct dma_chan *chan)
+{
+	/* just for check caps pass */
+	return -EINVAL;
+}
+
+static int mtk_dma_device_resume(struct dma_chan *chan)
+{
+	/* just for check caps pass */
+	return -EINVAL;
+}
+
+static void mtk_dma_free(struct mtk_dmadev *mtkd)
+{
+	tasklet_kill(&mtkd->task);
+	while (list_empty(&mtkd->ddev.channels) == 0) {
+		struct mtk_chan *c = list_first_entry(&mtkd->ddev.channels,
+			struct mtk_chan, vc.chan.device_node);
+
+		list_del(&c->vc.chan.device_node);
+		tasklet_kill(&c->vc.task);
+		devm_kfree(mtkd->ddev.dev, c);
+	}
+}
+
+static const struct of_device_id mtk_uart_dma_match[] = {
+	{ .compatible = "mediatek,mt6577-uart-dma", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mtk_uart_dma_match);
+
+static int mtk_apdma_probe(struct platform_device *pdev)
+{
+	struct mtk_dmadev *mtkd;
+	struct resource *res;
+	struct mtk_chan *c;
+	unsigned int i;
+	int rc;
+
+	mtkd = devm_kzalloc(&pdev->dev, sizeof(*mtkd), GFP_KERNEL);
+	if (!mtkd)
+		return -ENOMEM;
+
+	for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, i);
+		if (!res)
+			return -ENODEV;
+		mtkd->mem_base[i] = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(mtkd->mem_base[i]))
+			return PTR_ERR(mtkd->mem_base[i]);
+	}
+
+	for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
+		mtkd->dma_irq[i] = platform_get_irq(pdev, i);
+		if ((int)mtkd->dma_irq[i] < 0) {
+			dev_err(&pdev->dev, "failed to get IRQ[%d]\n", i);
+			return -EINVAL;
+		}
+	}
+
+	mtkd->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(mtkd->clk)) {
+		dev_err(&pdev->dev, "No clock specified\n");
+		return PTR_ERR(mtkd->clk);
+	}
+
+	if (of_property_read_bool(pdev->dev.of_node, "dma-33bits")) {
+		dev_info(&pdev->dev, "Support dma 33bits\n");
+		mtkd->support_33bits = true;
+	}
+
+	if (mtkd->support_33bits)
+		rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(33));
+	else
+		rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
+	if (rc)
+		return rc;
+
+	dma_cap_set(DMA_SLAVE, mtkd->ddev.cap_mask);
+	mtkd->ddev.device_alloc_chan_resources = mtk_dma_alloc_chan_resources;
+	mtkd->ddev.device_free_chan_resources = mtk_dma_free_chan_resources;
+	mtkd->ddev.device_tx_status = mtk_dma_tx_status;
+	mtkd->ddev.device_issue_pending = mtk_dma_issue_pending;
+	mtkd->ddev.device_prep_slave_sg = mtk_dma_prep_slave_sg;
+	mtkd->ddev.device_config = mtk_dma_slave_config;
+	mtkd->ddev.device_pause = mtk_dma_device_pause;
+	mtkd->ddev.device_resume = mtk_dma_device_resume;
+	mtkd->ddev.device_terminate_all = mtk_dma_terminate_all;
+	mtkd->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE);
+	mtkd->ddev.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE);
+	mtkd->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
+	mtkd->ddev.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
+	mtkd->ddev.dev = &pdev->dev;
+	INIT_LIST_HEAD(&mtkd->ddev.channels);
+	INIT_LIST_HEAD(&mtkd->pending);
+
+	spin_lock_init(&mtkd->lock);
+	tasklet_init(&mtkd->task, mtk_dma_sched, (unsigned long)mtkd);
+
+	mtkd->dma_requests = MTK_APDMA_DEFAULT_REQUESTS;
+	if (of_property_read_u32(pdev->dev.of_node,
+				 "dma-requests", &mtkd->dma_requests)) {
+		dev_info(&pdev->dev,
+			 "Missing dma-requests property, using %u.\n",
+			 MTK_APDMA_DEFAULT_REQUESTS);
+	}
+
+	for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
+		c = devm_kzalloc(mtkd->ddev.dev, sizeof(*c), GFP_KERNEL);
+		if (!c)
+			goto err_no_dma;
+
+		c->vc.desc_free = mtk_dma_desc_free;
+		vchan_init(&c->vc, &mtkd->ddev);
+		INIT_LIST_HEAD(&c->node);
+	}
+
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_set_active(&pdev->dev);
+
+	rc = dma_async_device_register(&mtkd->ddev);
+	if (rc)
+		goto rpm_disable;
+
+	platform_set_drvdata(pdev, mtkd);
+
+	if (pdev->dev.of_node) {
+		/* Device-tree DMA controller registration */
+		rc = of_dma_controller_register(pdev->dev.of_node,
+						of_dma_xlate_by_chan_id,
+						mtkd);
+		if (rc)
+			goto dma_remove;
+	}
+
+	return rc;
+
+dma_remove:
+	dma_async_device_unregister(&mtkd->ddev);
+rpm_disable:
+	pm_runtime_disable(&pdev->dev);
+err_no_dma:
+	mtk_dma_free(mtkd);
+	return rc;
+}
+
+static int mtk_apdma_remove(struct platform_device *pdev)
+{
+	struct mtk_dmadev *mtkd = platform_get_drvdata(pdev);
+
+	if (pdev->dev.of_node)
+		of_dma_controller_free(pdev->dev.of_node);
+
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+
+	dma_async_device_unregister(&mtkd->ddev);
+
+	mtk_dma_free(mtkd);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int mtk_dma_suspend(struct device *dev)
+{
+	struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
+
+	if (!pm_runtime_suspended(dev))
+		clk_disable_unprepare(mtkd->clk);
+
+	return 0;
+}
+
+static int mtk_dma_resume(struct device *dev)
+{
+	int ret;
+	struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
+
+	if (!pm_runtime_suspended(dev)) {
+		ret = clk_prepare_enable(mtkd->clk);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+#ifdef CONFIG_PM
+static int mtk_dma_runtime_suspend(struct device *dev)
+{
+	struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(mtkd->clk);
+
+	return 0;
+}
+
+static int mtk_dma_runtime_resume(struct device *dev)
+{
+	int ret;
+	struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
+
+	ret = clk_prepare_enable(mtkd->clk);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+#endif /* CONFIG_PM */
+
+static const struct dev_pm_ops mtk_dma_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(mtk_dma_suspend, mtk_dma_resume)
+	SET_RUNTIME_PM_OPS(mtk_dma_runtime_suspend,
+			   mtk_dma_runtime_resume, NULL)
+};
+
+static struct platform_driver mtk_dma_driver = {
+	.probe	= mtk_apdma_probe,
+	.remove	= mtk_apdma_remove,
+	.driver = {
+		.name		= KBUILD_MODNAME,
+		.pm		= &mtk_dma_pm_ops,
+		.of_match_table = of_match_ptr(mtk_uart_dma_match),
+	},
+};
+
+module_platform_driver(mtk_dma_driver);
+
+MODULE_DESCRIPTION("MediaTek UART APDMA Controller Driver");
+MODULE_AUTHOR("Long Cheng <long.cheng@mediatek.com>");
+MODULE_LICENSE("GPL v2");
+
diff --git a/drivers/dma/mediatek/Kconfig b/drivers/dma/mediatek/Kconfig
index 27bac0b..d399624 100644
--- a/drivers/dma/mediatek/Kconfig
+++ b/drivers/dma/mediatek/Kconfig
@@ -1,4 +1,15 @@
 
+config DMA_MTK_UART
+	tristate "MediaTek SoCs APDMA support for UART"
+	depends on OF && SERIAL_8250_MT6577
+	select DMA_ENGINE
+	select DMA_VIRTUAL_CHANNELS
+	help
+	  Support for the UART DMA engine found on MediaTek MTK SoCs.
+	  when 8250 mtk uart is enabled, and if you want to using DMA,
+	  you can enable the config. the DMA engine just only be used
+	  with MediaTek Socs.
+
 config MTK_HSDMA
 	tristate "MediaTek High-Speed DMA controller support"
 	depends on ARCH_MEDIATEK || COMPILE_TEST
diff --git a/drivers/dma/mediatek/Makefile b/drivers/dma/mediatek/Makefile
index 6e778f8..2f2efd9 100644
--- a/drivers/dma/mediatek/Makefile
+++ b/drivers/dma/mediatek/Makefile
@@ -1 +1,2 @@
+obj-$(CONFIG_DMA_MTK_UART) += 8250_mtk_dma.o
 obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o
-- 
1.7.9.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 1/2] dmaengine: 8250_mtk_dma: add Mediatek uart DMA support

[Sean Wang]

Sorry for that I didn't have a full review at one time in the earlier version

       On Mon, Dec 10, 2018 at 9:37 PM Long Cheng
<long.cheng@mediatek.com> wrote:
>
> In DMA engine framework, add 8250 mtk dma to support it.

It looks like there are still many rooms to improve the description,
especially it's a totally new driver.

>
> Signed-off-by: Long Cheng <long.cheng@mediatek.com>
> ---
>  drivers/dma/mediatek/8250_mtk_dma.c |  830 +++++++++++++++++++++++++++++++++++
>  drivers/dma/mediatek/Kconfig        |   11 +
>  drivers/dma/mediatek/Makefile       |    1 +
>  3 files changed, 842 insertions(+)
>  create mode 100644 drivers/dma/mediatek/8250_mtk_dma.c
>
> diff --git a/drivers/dma/mediatek/8250_mtk_dma.c b/drivers/dma/mediatek/8250_mtk_dma.c
> new file mode 100644
> index 0000000..f79d180
> --- /dev/null
> +++ b/drivers/dma/mediatek/8250_mtk_dma.c
> @@ -0,0 +1,830 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Mediatek 8250 DMA driver.

MediaTek

> + *
> + * Copyright (c) 2018 MediaTek Inc.
> + * Author: Long Cheng <long.cheng@mediatek.com>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/dmaengine.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/err.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/list.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of_dma.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/iopoll.h>
> +
> +#include "../virt-dma.h"
> +
> +#define MTK_APDMA_DEFAULT_REQUESTS     127
> +#define MTK_APDMA_CHANNELS             (CONFIG_SERIAL_8250_NR_UARTS * 2)
> +
> +#define VFF_EN_B               BIT(0)
> +#define VFF_STOP_B             BIT(0)
> +#define VFF_FLUSH_B            BIT(0)
> +#define VFF_4G_SUPPORT_B       BIT(0)
> +#define VFF_RX_INT_EN0_B       BIT(0)  /*rx valid size >=  vff thre*/
> +#define VFF_RX_INT_EN1_B       BIT(1)
> +#define VFF_TX_INT_EN_B                BIT(0)  /*tx left size >= vff thre*/
> +#define VFF_WARM_RST_B         BIT(0)
> +#define VFF_RX_INT_FLAG_CLR_B  (BIT(0) | BIT(1))
> +#define VFF_TX_INT_FLAG_CLR_B  0
> +#define VFF_STOP_CLR_B         0
> +#define VFF_FLUSH_CLR_B                0
> +#define VFF_INT_EN_CLR_B       0
> +#define VFF_4G_SUPPORT_CLR_B   0
> +
> +/* interrupt trigger level for tx */
> +#define VFF_TX_THRE(n)         ((n) * 7 / 8)
> +/* interrupt trigger level for rx */
> +#define VFF_RX_THRE(n)         ((n) * 3 / 4)
> +
> +#define MTK_DMA_RING_SIZE      0xffffU
> +/* invert this bit when wrap ring head again*/
> +#define MTK_DMA_RING_WRAP      0x10000U
> +
> +#define VFF_INT_FLAG           0x00
> +#define VFF_INT_EN             0x04
> +#define VFF_EN                 0x08
> +#define VFF_RST                        0x0c
> +#define VFF_STOP               0x10
> +#define VFF_FLUSH              0x14
> +#define VFF_ADDR               0x1c
> +#define VFF_LEN                        0x24
> +#define VFF_THRE               0x28
> +#define VFF_WPT                        0x2c
> +#define VFF_RPT                        0x30
> +/*TX: the buffer size HW can read. RX: the buffer size SW can read.*/
> +#define VFF_VALID_SIZE         0x3c
> +/*TX: the buffer size SW can write. RX: the buffer size HW can write.*/
> +#define VFF_LEFT_SIZE          0x40
> +#define VFF_DEBUG_STATUS       0x50
> +#define VFF_4G_SUPPORT         0x54
> +
> +struct mtk_dmadev {
> +       struct dma_device ddev;
> +       void __iomem *mem_base[MTK_APDMA_CHANNELS];
> +       spinlock_t lock; /* dma dev lock */
> +       struct tasklet_struct task;

we can drop tasklet and instead allows descriptors to be handled as
fast as possible.
similar suggestions have been made in the other dmaengine [1] and mtk-hsdma.c

[1] https://lkml.org/lkml/2018/11/11/146

> +       struct list_head pending;
> +       struct clk *clk;
> +       unsigned int dma_requests;
> +       bool support_33bits;
> +       unsigned int dma_irq[MTK_APDMA_CHANNELS];
> +       struct mtk_chan *ch[MTK_APDMA_CHANNELS];
> +};
> +
> +struct mtk_chan {
> +       struct virt_dma_chan vc;
> +       struct list_head node;
> +       struct dma_slave_config cfg;
> +       void __iomem *base;
> +       struct mtk_dma_desc *desc;
> +
> +       bool stop;
> +       bool requested;
> +
> +       unsigned int rx_status;
> +};
> +
> +struct mtk_dma_sg {
> +       dma_addr_t addr;
> +       unsigned int en;                /* number of elements (24-bit) */
> +       unsigned int fn;                /* number of frames (16-bit) */
> +};
> +
> +struct mtk_dma_desc {
> +       struct virt_dma_desc vd;
> +       enum dma_transfer_direction dir;
> +
> +       unsigned int sglen;
> +       struct mtk_dma_sg sg[0];
> +
> +       unsigned int len;
> +};
> +
> +static inline struct mtk_dmadev *to_mtk_dma_dev(struct dma_device *d)
> +{
> +       return container_of(d, struct mtk_dmadev, ddev);
> +}
> +
> +static inline struct mtk_chan *to_mtk_dma_chan(struct dma_chan *c)
> +{
> +       return container_of(c, struct mtk_chan, vc.chan);
> +}
> +
> +static inline struct mtk_dma_desc *to_mtk_dma_desc
> +       (struct dma_async_tx_descriptor *t)
> +{
> +       return container_of(t, struct mtk_dma_desc, vd.tx);
> +}
> +
> +static void mtk_dma_chan_write(struct mtk_chan *c,
> +                              unsigned int reg, unsigned int val)
> +{
> +       writel(val, c->base + reg);
> +}
> +
> +static unsigned int mtk_dma_chan_read(struct mtk_chan *c, unsigned int reg)
> +{
> +       return readl(c->base + reg);
> +}
> +
> +static void mtk_dma_desc_free(struct virt_dma_desc *vd)
> +{
> +       struct dma_chan *chan = vd->tx.chan;
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +
> +       kfree(c->desc);
> +       c->desc = NULL;
> +}
> +
> +static void mtk_dma_tx_flush(struct dma_chan *chan)
> +{

If the user is only one, let's span the content into where the user is.

> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +
> +       if (mtk_dma_chan_read(c, VFF_FLUSH) == 0U)
> +               mtk_dma_chan_write(c, VFF_FLUSH, VFF_FLUSH_B);
> +}
> +
> +static void mtk_dma_tx_write(struct dma_chan *chan)
> +{

If the user is only one, let's span the content into where the user is.

> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       unsigned int txcount = c->desc->len;
> +       unsigned int len, send, left, wpt, wrap;
> +
> +       len = mtk_dma_chan_read(c, VFF_LEN);
> +
> +       while ((left = mtk_dma_chan_read(c, VFF_LEFT_SIZE)) > 0U) {
> +               if (c->desc->len == 0U)

merge the condition back into the condition in while

> +                       break;
> +               send = min_t(unsigned int, left, c->desc->len);
> +               wpt = mtk_dma_chan_read(c, VFF_WPT);
> +               wrap = wpt & MTK_DMA_RING_WRAP ? 0U : MTK_DMA_RING_WRAP;
> +
> +               if ((wpt & (len - 1U)) + send < len)
> +                       mtk_dma_chan_write(c, VFF_WPT, wpt + send);
> +               else
> +                       mtk_dma_chan_write(c, VFF_WPT,
> +                                          ((wpt + send) & (len - 1U))
> +                                          | wrap);
> +
> +               c->desc->len -= send;

->len can be renamed to ->avail_len to say it's variable during the work

> +       }
> +
> +       if (txcount != c->desc->len) {
> +               mtk_dma_chan_write(c, VFF_INT_EN, VFF_TX_INT_EN_B);
> +               mtk_dma_tx_flush(chan);
> +       }
> +}
> +
> +static void mtk_dma_start_tx(struct mtk_chan *c)
> +{
> +       if (mtk_dma_chan_read(c, VFF_LEFT_SIZE) == 0U)
> +               mtk_dma_chan_write(c, VFF_INT_EN, VFF_TX_INT_EN_B);
> +       else
> +               mtk_dma_tx_write(&c->vc.chan);
> +
> +       c->stop = false;
> +}
> +
> +static void mtk_dma_get_rx_size(struct mtk_chan *c)
> +{

If the user is only one, let's span the content into where the user is.

> +       unsigned int rx_size = mtk_dma_chan_read(c, VFF_LEN);
> +       unsigned int rdptr, wrptr, wrreg, rdreg, count;

too much variable seems a little lousy, two variables are enough

unsigned int rd, wr;

> +
> +       rdreg = mtk_dma_chan_read(c, VFF_RPT);
> +       wrreg = mtk_dma_chan_read(c, VFF_WPT);
> +       rdptr = rdreg & MTK_DMA_RING_SIZE;
> +       wrptr = wrreg & MTK_DMA_RING_SIZE;

rd = mtk_dma_chan_read(c, VFF_RPT) & MTK_DMA_RING_SIZE;
wr = mtk_dma_chan_read(c, VFF_WPT) & MTK_DMA_RING_SIZE

> +       count = ((rdreg ^ wrreg) & MTK_DMA_RING_WRAP) ?
> +                       (wrptr + rx_size - rdptr) : (wrptr - rdptr);
> +
> +       c->rx_status = count;

drop the variable count and have a direct assignment

> +
> +       mtk_dma_chan_write(c, VFF_RPT, wrreg);
> +}
> +
> +static void mtk_dma_start_rx(struct mtk_chan *c)
> +{
> +       struct dma_chan *chan = &c->vc.chan;
> +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
> +       struct mtk_dma_desc *d = c->desc;
> +
> +       if (mtk_dma_chan_read(c, VFF_VALID_SIZE) == 0U)
> +               return;
> +
> +       if (d && vchan_next_desc(&c->vc)) {
> +               mtk_dma_get_rx_size(c);
> +               list_del(&d->vd.node);
> +               vchan_cookie_complete(&d->vd);
> +       } else {
> +               spin_lock(&mtkd->lock);
> +               if (list_empty(&mtkd->pending))
> +                       list_add_tail(&c->node, &mtkd->pending);
> +               spin_unlock(&mtkd->lock);
> +               tasklet_schedule(&mtkd->task);
> +       }
> +}
> +
> +static void mtk_dma_reset(struct mtk_chan *c)
> +{

If the user is only one, let's span the content into where the user is.

> +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(c->vc.chan.device);
> +       u32 status;
> +       int ret;
> +
> +       mtk_dma_chan_write(c, VFF_ADDR, 0);
> +       mtk_dma_chan_write(c, VFF_THRE, 0);
> +       mtk_dma_chan_write(c, VFF_LEN, 0);
> +       mtk_dma_chan_write(c, VFF_RST, VFF_WARM_RST_B);
> +
> +       ret = readx_poll_timeout(readl,
> +                                c->base + VFF_EN,
> +                                status, status == 0, 10, 100);
> +       if (ret) {
> +               dev_err(c->vc.chan.device->dev,
> +                               "dma reset: fail, timeout\n");
> +               return;
> +       }
> +
> +       if (c->cfg.direction == DMA_DEV_TO_MEM)
> +               mtk_dma_chan_write(c, VFF_RPT, 0);
> +       else if (c->cfg.direction == DMA_MEM_TO_DEV)
> +               mtk_dma_chan_write(c, VFF_WPT, 0);

using switch and case statement

> +
> +       if (mtkd->support_33bits)
> +               mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_CLR_B);
> +}
> +
> +static void mtk_dma_stop(struct mtk_chan *c)

If the user is only one, let's span the content into where the user is.

> +{
> +       u32 status;
> +       int ret;
> +
> +       mtk_dma_chan_write(c, VFF_FLUSH, VFF_FLUSH_CLR_B);
> +       /* Wait for flush */
> +       ret = readx_poll_timeout(readl,
> +                                c->base + VFF_FLUSH,
> +                                status,
> +                                (status & VFF_FLUSH_B) != VFF_FLUSH_B,
> +                                10, 100);
> +       if (ret)
> +               dev_err(c->vc.chan.device->dev,
> +                       "dma stop: polling FLUSH fail, DEBUG=0x%x\n",
> +                       mtk_dma_chan_read(c, VFF_DEBUG_STATUS));
> +
> +       /*set stop as 1 -> wait until en is 0 -> set stop as 0*/
> +       mtk_dma_chan_write(c, VFF_STOP, VFF_STOP_B);
> +       ret = readx_poll_timeout(readl,
> +                                c->base + VFF_EN,
> +                                status, status == 0, 10, 100);
> +       if (ret)
> +               dev_err(c->vc.chan.device->dev,
> +                       "dma stop: polling VFF_EN fail, DEBUG=0x%x\n",
> +                       mtk_dma_chan_read(c, VFF_DEBUG_STATUS));
> +
> +       mtk_dma_chan_write(c, VFF_STOP, VFF_STOP_CLR_B);
> +       mtk_dma_chan_write(c, VFF_INT_EN, VFF_INT_EN_CLR_B);
> +
> +       if (c->cfg.direction == DMA_DEV_TO_MEM)
> +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> +       else
> +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);

using switch and case statement

> +
> +       c->stop = true;
> +}
> +
> +/*
> + * This callback schedules all pending channels. We could be more
> + * clever here by postponing allocation of the real DMA channels to
> + * this point, and freeing them when our virtual channel becomes idle.
> + *
> + * We would then need to deal with 'all channels in-use'
> + */
> +static void mtk_dma_sched(unsigned long data)
> +{

As at the initial be said, try to make descriptors submit as fast as
possible without involving in a tasklet. The same improvement had been
done at mtk-hsdma.c  so you could have a reference to it first if you
have no much idea of how to begin to improve.

> +       struct mtk_dmadev *mtkd = (struct mtk_dmadev *)data;
> +       struct virt_dma_desc *vd;
> +       struct mtk_chan *c;
> +       unsigned long flags;
> +       LIST_HEAD(head);
> +
> +       spin_lock_irq(&mtkd->lock);
> +       list_splice_tail_init(&mtkd->pending, &head);
> +       spin_unlock_irq(&mtkd->lock);
> +
> +       if (!list_empty(&head)) {
> +               c = list_first_entry(&head, struct mtk_chan, node);
> +
> +               spin_lock_irqsave(&c->vc.lock, flags);
> +               if (c->cfg.direction == DMA_DEV_TO_MEM) {
> +                       list_del_init(&c->node);
> +                       mtk_dma_start_rx(c);
> +               } else if (c->cfg.direction == DMA_MEM_TO_DEV) {
> +                       vd = vchan_next_desc(&c->vc);
> +                       c->desc = to_mtk_dma_desc(&vd->tx);
> +                       list_del_init(&c->node);
> +                       mtk_dma_start_tx(c);
> +               }
> +               spin_unlock_irqrestore(&c->vc.lock, flags);
> +       }
> +}
> +
> +static int mtk_dma_alloc_chan_resources(struct dma_chan *chan)
> +{
> +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       int ret = -EBUSY;
> +
> +       pm_runtime_get_sync(mtkd->ddev.dev);
> +
> +       if (!mtkd->ch[chan->chan_id]) {
> +               c->base = mtkd->mem_base[chan->chan_id]

mtkd->mem_base is unnecessary, we can directly decide c->base in the
driver probe stage

> +               mtkd->ch[chan->chan_id] = c;

mtkd->ch is also unnecessary, the core always pass struct dma_chan
*chan to each callback function

> +               ret = 1;

ret be 1 seems be wrong

> +       }
> +       c->requested = false;
> +       mtk_dma_reset(c);
> +
> +       return ret;
> +}
> +
> +static void mtk_dma_free_chan_resources(struct dma_chan *chan)
> +{
> +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +
> +       if (c->requested) {
> +               c->requested = false;
> +               free_irq(mtkd->dma_irq[chan->chan_id], chan);

it makes not consistent because there are not request_irq present at
mtk_dma_alloc_chan_resources. but I'd prefer a  devm_request_irq is
being done
as the driver got probe.

> +       }
> +
> +       tasklet_kill(&mtkd->task);
> +       tasklet_kill(&c->vc.task);
> +
> +       c->base = NULL;
> +       mtkd->ch[chan->chan_id] = NULL;
> +       vchan_free_chan_resources(&c->vc);
> +
> +       pm_runtime_put_sync(mtkd->ddev.dev);
> +}
> +
> +static enum dma_status mtk_dma_tx_status(struct dma_chan *chan,
> +                                        dma_cookie_t cookie,
> +                                        struct dma_tx_state *txstate)
> +{
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       enum dma_status ret;
> +       unsigned long flags;
> +
> +       if (!txstate)
> +               return DMA_ERROR;
> +
> +       ret = dma_cookie_status(chan, cookie, txstate);
> +       spin_lock_irqsave(&c->vc.lock, flags);
> +       if (ret == DMA_IN_PROGRESS) {
> +               c->rx_status = mtk_dma_chan_read(c, VFF_RPT)
> +                            & MTK_DMA_RING_SIZE;
> +               dma_set_residue(txstate, c->rx_status);
> +       } else if (ret == DMA_COMPLETE && c->cfg.direction == DMA_DEV_TO_MEM) {
> +               dma_set_residue(txstate, c->rx_status);
> +       } else {
> +               dma_set_residue(txstate, 0);
> +       }
> +       spin_unlock_irqrestore(&c->vc.lock, flags);
> +
> +       return ret;
> +}
> +
> +static struct dma_async_tx_descriptor *mtk_dma_prep_slave_sg
> +       (struct dma_chan *chan, struct scatterlist *sgl,
> +       unsigned int sglen,     enum dma_transfer_direction dir,
> +       unsigned long tx_flags, void *context)
> +{
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       struct scatterlist *sgent;
> +       struct mtk_dma_desc *d;
> +       struct mtk_dma_sg *sg;
> +       unsigned int size, i, j, en;
> +
> +       en = 1;
> +
> +       if ((dir != DMA_DEV_TO_MEM) &&
> +               (dir != DMA_MEM_TO_DEV)) {
> +               dev_err(chan->device->dev, "bad direction\n");
> +               return NULL;
> +       }
> +
> +       /* Now allocate and setup the descriptor. */
> +       d = kzalloc(sizeof(*d) + sglen * sizeof(d->sg[0]), GFP_ATOMIC);
> +       if (!d)
> +               return NULL;
> +
> +       d->dir = dir;
> +
> +       j = 0;
> +       for_each_sg(sgl, sgent, sglen, i) {
> +               d->sg[j].addr = sg_dma_address(sgent);
> +               d->sg[j].en = en;
> +               d->sg[j].fn = sg_dma_len(sgent) / en;
> +               j++;
> +       }
> +
> +       d->sglen = j;
> +
> +       if (dir == DMA_MEM_TO_DEV) {
> +               for (size = i = 0; i < d->sglen; i++) {
> +                       sg = &d->sg[i];
> +                       size += sg->en * sg->fn;
> +               }
> +               d->len = size;
> +       }
> +

The driver always only handles data move for the single contiguous
area, but it seems the callback must provide the scatter-gather
function to the dmaegine. otherwise, why is the callback be called
device_prep_slave_sg?

> +       return vchan_tx_prep(&c->vc, &d->vd, tx_flags);
> +}
> +
> +static void mtk_dma_issue_pending(struct dma_chan *chan)
> +{
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       struct virt_dma_desc *vd;
> +       struct mtk_dmadev *mtkd;
> +       unsigned long flags;
> +
> +       spin_lock_irqsave(&c->vc.lock, flags);
> +       if (c->cfg.direction == DMA_DEV_TO_MEM) {
> +               mtkd = to_mtk_dma_dev(chan->device);

mtkd can be dropped as it seems no users

> +               if (vchan_issue_pending(&c->vc) && !c->desc) {
> +                       vd = vchan_next_desc(&c->vc);
> +                       c->desc = to_mtk_dma_desc(&vd->tx);
> +               }
> +       } else if (c->cfg.direction == DMA_MEM_TO_DEV) {
> +               if (vchan_issue_pending(&c->vc) && !c->desc) {
> +                       vd = vchan_next_desc(&c->vc);
> +                       c->desc = to_mtk_dma_desc(&vd->tx);
> +                       mtk_dma_start_tx(c);
> +               }
> +       }
> +       spin_unlock_irqrestore(&c->vc.lock, flags);
> +}
> +
> +static irqreturn_t mtk_dma_rx_interrupt(int irq, void *dev_id)
> +{
> +       struct dma_chan *chan = (struct dma_chan *)dev_id;
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       unsigned long flags;
> +
> +       spin_lock_irqsave(&c->vc.lock, flags);
> +       mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> +
> +       mtk_dma_start_rx(c);
> +
> +       spin_unlock_irqrestore(&c->vc.lock, flags);
> +
> +       return IRQ_HANDLED;
> +}
> +
> +static irqreturn_t mtk_dma_tx_interrupt(int irq, void *dev_id)
> +{
> +       struct dma_chan *chan = (struct dma_chan *)dev_id;
> +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       struct mtk_dma_desc *d = c->desc;
> +       unsigned long flags;
> +
> +       spin_lock_irqsave(&c->vc.lock, flags);
> +       if (d->len != 0U) {
> +               list_add_tail(&c->node, &mtkd->pending);
> +               tasklet_schedule(&mtkd->task);
> +       } else {
> +               list_del(&d->vd.node);
> +               vchan_cookie_complete(&d->vd);
> +       }
> +       spin_unlock_irqrestore(&c->vc.lock, flags);
> +
> +       mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> +
> +       return IRQ_HANDLED;
> +}
> +
> +static int mtk_dma_slave_config(struct dma_chan *chan,
> +                               struct dma_slave_config *cfg)
> +{
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(c->vc.chan.device);
> +       int ret;
> +
> +       c->cfg = *cfg;
> +
> +       if (cfg->direction == DMA_DEV_TO_MEM) {
> +               unsigned int rx_len = cfg->src_addr_width * 1024;

it seems you should use cfg->src_port_window_size as the comments explains

* @src_port_window_size: The length of the register area in words the data need
 * to be accessed on the device side. It is only used for devices which is using
 * an area instead of a single register to receive the data. Typically the DMA
 * loops in this area in order to transfer the data.
 * @dst_port_window_size: same as src_port_window_size but for the destination
 * port.

> +
> +               mtk_dma_chan_write(c, VFF_ADDR, cfg->src_addr);
> +               mtk_dma_chan_write(c, VFF_LEN, rx_len);
> +               mtk_dma_chan_write(c, VFF_THRE, VFF_RX_THRE(rx_len));
> +               mtk_dma_chan_write(c,
> +                                  VFF_INT_EN, VFF_RX_INT_EN0_B
> +                                  | VFF_RX_INT_EN1_B);
> +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);

I'd prefer to move those channel interrupt enablement to
.device_alloc_chan_resources
and related disablement to .device_free_chan_resources

> +
> +               if (!c->requested) {
> +                       c->requested = true;
> +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> +                                         mtk_dma_rx_interrupt,
> +                                         IRQF_TRIGGER_NONE,
> +                                         KBUILD_MODNAME, chan);

ISR registration usually happens as the driver got probe, it can give
the system more flexibility to manage such IRQ affinity on the fly.

> +                       if (ret < 0) {
> +                               dev_err(chan->device->dev, "Can't request rx dma IRQ\n");
> +                               return -EINVAL;
> +                       }
> +               }
> +       } else if (cfg->direction == DMA_MEM_TO_DEV)    {
> +               unsigned int tx_len = cfg->dst_addr_width * 1024;

Ditto as above, it seems you should use cfg->dst_port_window_size

> +
> +               mtk_dma_chan_write(c, VFF_ADDR, cfg->dst_addr);
> +               mtk_dma_chan_write(c, VFF_LEN, tx_len);
> +               mtk_dma_chan_write(c, VFF_THRE, VFF_TX_THRE(tx_len));
> +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);

ditto, I'd prefer to move those channel interrupt enablement to
.device_alloc_chan_resources and related disablement to
.device_free_chan_resources

> +
> +               if (!c->requested) {
> +                       c->requested = true;
> +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> +                                         mtk_dma_tx_interrupt,
> +                                         IRQF_TRIGGER_NONE,
> +                                         KBUILD_MODNAME, chan);

ditto, we can request ISR with devm_request_irq in the driver got
probe and trim the c->request member

> +                       if (ret < 0) {
> +                               dev_err(chan->device->dev, "Can't request tx dma IRQ\n");
> +                               return -EINVAL;
> +                       }
> +               }
> +       }
> +
> +       if (mtkd->support_33bits)
> +               mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_B);
> +
> +       if (mtk_dma_chan_read(c, VFF_EN) != VFF_EN_B) {
> +               dev_err(chan->device->dev,
> +                       "config dma dir[%d] fail\n", cfg->direction);
> +               return -EINVAL;
> +       }
> +
> +       return 0;
> +}
> +
> +static int mtk_dma_terminate_all(struct dma_chan *chan)
> +{
> +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> +       unsigned long flags;
> +
> +       spin_lock_irqsave(&c->vc.lock, flags);
> +       list_del_init(&c->node);
> +       mtk_dma_stop(c);
> +       spin_unlock_irqrestore(&c->vc.lock, flags);
> +
> +       return 0;
> +}
> +
> +static int mtk_dma_device_pause(struct dma_chan *chan)
> +{
> +       /* just for check caps pass */
> +       return -EINVAL;

always return error code seems not the client driver wants us to do.

maybe if the hardware doesn't support pause, we can make a software
pause, that waits until all active descriptors in hardware done, then
disable interrupt and then stop handling the following vd in the
vchan.

> +}
> +
> +static int mtk_dma_device_resume(struct dma_chan *chan)
> +{
> +       /* just for check caps pass */
> +       return -EINVAL;

similar to the above

> +}
> +
> +static void mtk_dma_free(struct mtk_dmadev *mtkd)
> +{
> +       tasklet_kill(&mtkd->task);
> +       while (list_empty(&mtkd->ddev.channels) == 0) {
!list_empty(&mtkd->ddev.channels)
> +               struct mtk_chan *c = list_first_entry(&mtkd->ddev.channels,
> +                       struct mtk_chan, vc.chan.device_node);
> +
> +               list_del(&c->vc.chan.device_node);
> +               tasklet_kill(&c->vc.task);
> +               devm_kfree(mtkd->ddev.dev, c);

no need to call devm_kfree, the core would help do this

> +       }
> +}
> +
> +static const struct of_device_id mtk_uart_dma_match[] = {
> +       { .compatible = "mediatek,mt6577-uart-dma", },
> +       { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, mtk_uart_dma_match);
> +
> +static int mtk_apdma_probe(struct platform_device *pdev)
> +{
> +       struct mtk_dmadev *mtkd;
> +       struct resource *res;
> +       struct mtk_chan *c;
> +       unsigned int i;
> +       int rc;
> +
> +       mtkd = devm_kzalloc(&pdev->dev, sizeof(*mtkd), GFP_KERNEL);
> +       if (!mtkd)
> +               return -ENOMEM;
> +
> +       for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
> +               res = platform_get_resource(pdev, IORESOURCE_MEM, i);
> +               if (!res)
> +                       return -ENODEV;
> +               mtkd->mem_base[i] = devm_ioremap_resource(&pdev->dev, res);
> +               if (IS_ERR(mtkd->mem_base[i]))
> +                       return PTR_ERR(mtkd->mem_base[i]);
> +       }
> +
> +       for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
> +               mtkd->dma_irq[i] = platform_get_irq(pdev, i);
> +               if ((int)mtkd->dma_irq[i] < 0) {
> +                       dev_err(&pdev->dev, "failed to get IRQ[%d]\n", i);
> +                       return -EINVAL;
> +               }
> +       }
> +
> +       mtkd->clk = devm_clk_get(&pdev->dev, NULL);
> +       if (IS_ERR(mtkd->clk)) {
> +               dev_err(&pdev->dev, "No clock specified\n");
> +               return PTR_ERR(mtkd->clk);
> +       }
> +
> +       if (of_property_read_bool(pdev->dev.of_node, "dma-33bits")) {
> +               dev_info(&pdev->dev, "Support dma 33bits\n");
> +               mtkd->support_33bits = true;
> +       }
> +
> +       if (mtkd->support_33bits)
> +               rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(33));
> +       else
> +               rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));

 rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32 |
mtkd->support_33bits));

> +       if (rc)
> +               return rc;
> +
> +       dma_cap_set(DMA_SLAVE, mtkd->ddev.cap_mask);
> +       mtkd->ddev.device_alloc_chan_resources = mtk_dma_alloc_chan_resources;
> +       mtkd->ddev.device_free_chan_resources = mtk_dma_free_chan_resources;
> +       mtkd->ddev.device_tx_status = mtk_dma_tx_status;
> +       mtkd->ddev.device_issue_pending = mtk_dma_issue_pending;
> +       mtkd->ddev.device_prep_slave_sg = mtk_dma_prep_slave_sg;
> +       mtkd->ddev.device_config = mtk_dma_slave_config;
> +       mtkd->ddev.device_pause = mtk_dma_device_pause;
> +       mtkd->ddev.device_resume = mtk_dma_device_resume;
> +       mtkd->ddev.device_terminate_all = mtk_dma_terminate_all;
> +       mtkd->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE);
> +       mtkd->ddev.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE);
> +       mtkd->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
> +       mtkd->ddev.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
> +       mtkd->ddev.dev = &pdev->dev;
> +       INIT_LIST_HEAD(&mtkd->ddev.channels);
> +       INIT_LIST_HEAD(&mtkd->pending);
> +
> +       spin_lock_init(&mtkd->lock);
> +       tasklet_init(&mtkd->task, mtk_dma_sched, (unsigned long)mtkd);
> +
> +       mtkd->dma_requests = MTK_APDMA_DEFAULT_REQUESTS;
> +       if (of_property_read_u32(pdev->dev.of_node,
> +                                "dma-requests", &mtkd->dma_requests)) {
> +               dev_info(&pdev->dev,
> +                        "Missing dma-requests property, using %u.\n",
> +                        MTK_APDMA_DEFAULT_REQUESTS);
> +       }
> +
> +       for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
> +               c = devm_kzalloc(mtkd->ddev.dev, sizeof(*c), GFP_KERNEL);
> +               if (!c)
> +                       goto err_no_dma;
> +
> +               c->vc.desc_free = mtk_dma_desc_free;
> +               vchan_init(&c->vc, &mtkd->ddev);
> +               INIT_LIST_HEAD(&c->node);
> +       }
> +
> +       pm_runtime_enable(&pdev->dev);
> +       pm_runtime_set_active(&pdev->dev);
> +
> +       rc = dma_async_device_register(&mtkd->ddev);
> +       if (rc)
> +               goto rpm_disable;
> +
> +       platform_set_drvdata(pdev, mtkd);
> +
> +       if (pdev->dev.of_node) {
> +               /* Device-tree DMA controller registration */
> +               rc = of_dma_controller_register(pdev->dev.of_node,
> +                                               of_dma_xlate_by_chan_id,
> +                                               mtkd);
> +               if (rc)
> +                       goto dma_remove;
> +       }
> +
> +       return rc;
> +
> +dma_remove:
> +       dma_async_device_unregister(&mtkd->ddev);
> +rpm_disable:
> +       pm_runtime_disable(&pdev->dev);
> +err_no_dma:
> +       mtk_dma_free(mtkd);
> +       return rc;
> +}
> +
> +static int mtk_apdma_remove(struct platform_device *pdev)
> +{
> +       struct mtk_dmadev *mtkd = platform_get_drvdata(pdev);
> +
> +       if (pdev->dev.of_node)
> +               of_dma_controller_free(pdev->dev.of_node);
> +
> +       pm_runtime_disable(&pdev->dev);
> +       pm_runtime_put_noidle(&pdev->dev);
> +
> +       dma_async_device_unregister(&mtkd->ddev);
> +
> +       mtk_dma_free(mtkd);
> +
> +       return 0;
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int mtk_dma_suspend(struct device *dev)
> +{
> +       struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
> +
> +       if (!pm_runtime_suspended(dev))
> +               clk_disable_unprepare(mtkd->clk);
> +
> +       return 0;
> +}
> +
> +static int mtk_dma_resume(struct device *dev)
> +{
> +       int ret;
> +       struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
> +
> +       if (!pm_runtime_suspended(dev)) {
> +               ret = clk_prepare_enable(mtkd->clk);
> +               if (ret)
> +                       return ret;
> +       }
> +
> +       return 0;
> +}
> +#endif /* CONFIG_PM_SLEEP */
> +
> +#ifdef CONFIG_PM
> +static int mtk_dma_runtime_suspend(struct device *dev)
> +{
> +       struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
> +
> +       clk_disable_unprepare(mtkd->clk);
> +
> +       return 0;
> +}
> +
> +static int mtk_dma_runtime_resume(struct device *dev)
> +{
> +       int ret;
> +       struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
> +
> +       ret = clk_prepare_enable(mtkd->clk);
> +       if (ret)
> +               return ret;
> +
> +       return 0;
> +}
> +#endif /* CONFIG_PM */
> +
> +static const struct dev_pm_ops mtk_dma_pm_ops = {
> +       SET_SYSTEM_SLEEP_PM_OPS(mtk_dma_suspend, mtk_dma_resume)
> +       SET_RUNTIME_PM_OPS(mtk_dma_runtime_suspend,
> +                          mtk_dma_runtime_resume, NULL)
> +};
> +
> +static struct platform_driver mtk_dma_driver = {

mtk_dma is much general and all functions and structures in the driver
should be all consistent.  I'd prefer to have all naming starts with
mtk_uart_apdma.

> +       .probe  = mtk_apdma_probe,

such  as
mtk_uart_apdma_probe

> +       .remove = mtk_apdma_remove,

mtk_uart_apdma_remove

> +       .driver = {
> +               .name           = KBUILD_MODNAME,
> +               .pm             = &mtk_dma_pm_ops,

mtk_uart_apdma_pm_ops

> +               .of_match_table = of_match_ptr(mtk_uart_dma_match),

mtk_uart_apdma_match

> +       },
> +};
> +
> +module_platform_driver(mtk_dma_driver);

mtk_uart_apdma_driver

> +
> +MODULE_DESCRIPTION("MediaTek UART APDMA Controller Driver");
> +MODULE_AUTHOR("Long Cheng <long.cheng@mediatek.com>");
> +MODULE_LICENSE("GPL v2");
> +
> diff --git a/drivers/dma/mediatek/Kconfig b/drivers/dma/mediatek/Kconfig
> index 27bac0b..d399624 100644
> --- a/drivers/dma/mediatek/Kconfig
> +++ b/drivers/dma/mediatek/Kconfig
> @@ -1,4 +1,15 @@
>
> +config DMA_MTK_UART

MTK_UART_APDMA to align the other drivers

> +       tristate "MediaTek SoCs APDMA support for UART"
> +       depends on OF && SERIAL_8250_MT6577
> +       select DMA_ENGINE
> +       select DMA_VIRTUAL_CHANNELS
> +       help
> +         Support for the UART DMA engine found on MediaTek MTK SoCs.
> +         when 8250 mtk uart is enabled, and if you want to using DMA,

8250 mtk uart should be changed to SERIAL_8250_MT6577 to be more intuitive

> +         you can enable the config. the DMA engine just only be used
> +         with MediaTek Socs.

SoCs

> +
>  config MTK_HSDMA
>         tristate "MediaTek High-Speed DMA controller support"
>         depends on ARCH_MEDIATEK || COMPILE_TEST
> diff --git a/drivers/dma/mediatek/Makefile b/drivers/dma/mediatek/Makefile
> index 6e778f8..2f2efd9 100644
> --- a/drivers/dma/mediatek/Makefile
> +++ b/drivers/dma/mediatek/Makefile
> @@ -1 +1,2 @@
> +obj-$(CONFIG_DMA_MTK_UART) += 8250_mtk_dma.o

obj-$(CONFIG_MTK_UART_APDMA) += mtk-uart-apdma.o
to align the other dirvers

>  obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o
> --
> 1.7.9.5
>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 1/2] dmaengine: 8250_mtk_dma: add Mediatek uart DMA support

[Long Cheng]

On Tue, 2018-12-11 at 15:12 -0800, Sean Wang wrote:
> Sorry for that I didn't have a full review at one time in the earlier version
> 
>        On Mon, Dec 10, 2018 at 9:37 PM Long Cheng
> <long.cheng@mediatek.com> wrote:
> >
> > In DMA engine framework, add 8250 mtk dma to support it.
> 
> It looks like there are still many rooms to improve the description,
> especially it's a totally new driver.
> 
> >
> > Signed-off-by: Long Cheng <long.cheng@mediatek.com>
> > ---
> >  drivers/dma/mediatek/8250_mtk_dma.c |  830 +++++++++++++++++++++++++++++++++++
> >  drivers/dma/mediatek/Kconfig        |   11 +
> >  drivers/dma/mediatek/Makefile       |    1 +
> >  3 files changed, 842 insertions(+)
> >  create mode 100644 drivers/dma/mediatek/8250_mtk_dma.c
> >
> > diff --git a/drivers/dma/mediatek/8250_mtk_dma.c b/drivers/dma/mediatek/8250_mtk_dma.c
> > new file mode 100644
> > index 0000000..f79d180
> > --- /dev/null
> > +++ b/drivers/dma/mediatek/8250_mtk_dma.c
> > @@ -0,0 +1,830 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Mediatek 8250 DMA driver.
> 
> MediaTek
> 
> > + *
> > + * Copyright (c) 2018 MediaTek Inc.
> > + * Author: Long Cheng <long.cheng@mediatek.com>
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/dmaengine.h>
> > +#include <linux/dma-mapping.h>
> > +#include <linux/err.h>
> > +#include <linux/init.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/list.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/of_dma.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/slab.h>
> > +#include <linux/spinlock.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/iopoll.h>
> > +
> > +#include "../virt-dma.h"
> > +
> > +#define MTK_APDMA_DEFAULT_REQUESTS     127
> > +#define MTK_APDMA_CHANNELS             (CONFIG_SERIAL_8250_NR_UARTS * 2)
> > +
> > +#define VFF_EN_B               BIT(0)
> > +#define VFF_STOP_B             BIT(0)
> > +#define VFF_FLUSH_B            BIT(0)
> > +#define VFF_4G_SUPPORT_B       BIT(0)
> > +#define VFF_RX_INT_EN0_B       BIT(0)  /*rx valid size >=  vff thre*/
> > +#define VFF_RX_INT_EN1_B       BIT(1)
> > +#define VFF_TX_INT_EN_B                BIT(0)  /*tx left size >= vff thre*/
> > +#define VFF_WARM_RST_B         BIT(0)
> > +#define VFF_RX_INT_FLAG_CLR_B  (BIT(0) | BIT(1))
> > +#define VFF_TX_INT_FLAG_CLR_B  0
> > +#define VFF_STOP_CLR_B         0
> > +#define VFF_FLUSH_CLR_B                0
> > +#define VFF_INT_EN_CLR_B       0
> > +#define VFF_4G_SUPPORT_CLR_B   0
> > +
> > +/* interrupt trigger level for tx */
> > +#define VFF_TX_THRE(n)         ((n) * 7 / 8)
> > +/* interrupt trigger level for rx */
> > +#define VFF_RX_THRE(n)         ((n) * 3 / 4)
> > +
> > +#define MTK_DMA_RING_SIZE      0xffffU
> > +/* invert this bit when wrap ring head again*/
> > +#define MTK_DMA_RING_WRAP      0x10000U
> > +
> > +#define VFF_INT_FLAG           0x00
> > +#define VFF_INT_EN             0x04
> > +#define VFF_EN                 0x08
> > +#define VFF_RST                        0x0c
> > +#define VFF_STOP               0x10
> > +#define VFF_FLUSH              0x14
> > +#define VFF_ADDR               0x1c
> > +#define VFF_LEN                        0x24
> > +#define VFF_THRE               0x28
> > +#define VFF_WPT                        0x2c
> > +#define VFF_RPT                        0x30
> > +/*TX: the buffer size HW can read. RX: the buffer size SW can read.*/
> > +#define VFF_VALID_SIZE         0x3c
> > +/*TX: the buffer size SW can write. RX: the buffer size HW can write.*/
> > +#define VFF_LEFT_SIZE          0x40
> > +#define VFF_DEBUG_STATUS       0x50
> > +#define VFF_4G_SUPPORT         0x54
> > +
> > +struct mtk_dmadev {
> > +       struct dma_device ddev;
> > +       void __iomem *mem_base[MTK_APDMA_CHANNELS];
> > +       spinlock_t lock; /* dma dev lock */
> > +       struct tasklet_struct task;
> 
> we can drop tasklet and instead allows descriptors to be handled as
> fast as possible.
> similar suggestions have been made in the other dmaengine [1] and mtk-hsdma.c
> 

OK, i will remove these, and improve it.

> [1] https://lkml.org/lkml/2018/11/11/146
> 
> > +       struct list_head pending;
> > +       struct clk *clk;
> > +       unsigned int dma_requests;
> > +       bool support_33bits;
> > +       unsigned int dma_irq[MTK_APDMA_CHANNELS];
> > +       struct mtk_chan *ch[MTK_APDMA_CHANNELS];
> > +};
> > +
> > +struct mtk_chan {
> > +       struct virt_dma_chan vc;
> > +       struct list_head node;
> > +       struct dma_slave_config cfg;
> > +       void __iomem *base;
> > +       struct mtk_dma_desc *desc;
> > +
> > +       bool stop;
> > +       bool requested;
> > +
> > +       unsigned int rx_status;
> > +};
> > +
> > +struct mtk_dma_sg {
> > +       dma_addr_t addr;
> > +       unsigned int en;                /* number of elements (24-bit) */
> > +       unsigned int fn;                /* number of frames (16-bit) */
> > +};
> > +
> > +struct mtk_dma_desc {
> > +       struct virt_dma_desc vd;
> > +       enum dma_transfer_direction dir;
> > +
> > +       unsigned int sglen;
> > +       struct mtk_dma_sg sg[0];
> > +
> > +       unsigned int len;
> > +};
> > +
> > +static inline struct mtk_dmadev *to_mtk_dma_dev(struct dma_device *d)
> > +{
> > +       return container_of(d, struct mtk_dmadev, ddev);
> > +}
> > +
> > +static inline struct mtk_chan *to_mtk_dma_chan(struct dma_chan *c)
> > +{
> > +       return container_of(c, struct mtk_chan, vc.chan);
> > +}
> > +
> > +static inline struct mtk_dma_desc *to_mtk_dma_desc
> > +       (struct dma_async_tx_descriptor *t)
> > +{
> > +       return container_of(t, struct mtk_dma_desc, vd.tx);
> > +}
> > +
> > +static void mtk_dma_chan_write(struct mtk_chan *c,
> > +                              unsigned int reg, unsigned int val)
> > +{
> > +       writel(val, c->base + reg);
> > +}
> > +
> > +static unsigned int mtk_dma_chan_read(struct mtk_chan *c, unsigned int reg)
> > +{
> > +       return readl(c->base + reg);
> > +}
> > +
> > +static void mtk_dma_desc_free(struct virt_dma_desc *vd)
> > +{
> > +       struct dma_chan *chan = vd->tx.chan;
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +
> > +       kfree(c->desc);
> > +       c->desc = NULL;
> > +}
> > +
> > +static void mtk_dma_tx_flush(struct dma_chan *chan)
> > +{
> 
> If the user is only one, let's span the content into where the user is.
> 
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +
> > +       if (mtk_dma_chan_read(c, VFF_FLUSH) == 0U)
> > +               mtk_dma_chan_write(c, VFF_FLUSH, VFF_FLUSH_B);
> > +}
> > +
> > +static void mtk_dma_tx_write(struct dma_chan *chan)
> > +{
> 
> If the user is only one, let's span the content into where the user is.
> 
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       unsigned int txcount = c->desc->len;
> > +       unsigned int len, send, left, wpt, wrap;
> > +
> > +       len = mtk_dma_chan_read(c, VFF_LEN);
> > +
> > +       while ((left = mtk_dma_chan_read(c, VFF_LEFT_SIZE)) > 0U) {
> > +               if (c->desc->len == 0U)
> 
> merge the condition back into the condition in while
> 
> > +                       break;
> > +               send = min_t(unsigned int, left, c->desc->len);
> > +               wpt = mtk_dma_chan_read(c, VFF_WPT);
> > +               wrap = wpt & MTK_DMA_RING_WRAP ? 0U : MTK_DMA_RING_WRAP;
> > +
> > +               if ((wpt & (len - 1U)) + send < len)
> > +                       mtk_dma_chan_write(c, VFF_WPT, wpt + send);
> > +               else
> > +                       mtk_dma_chan_write(c, VFF_WPT,
> > +                                          ((wpt + send) & (len - 1U))
> > +                                          | wrap);
> > +
> > +               c->desc->len -= send;
> 
> ->len can be renamed to ->avail_len to say it's variable during the work
> 
> > +       }
> > +
> > +       if (txcount != c->desc->len) {
> > +               mtk_dma_chan_write(c, VFF_INT_EN, VFF_TX_INT_EN_B);
> > +               mtk_dma_tx_flush(chan);
> > +       }
> > +}
> > +
> > +static void mtk_dma_start_tx(struct mtk_chan *c)
> > +{
> > +       if (mtk_dma_chan_read(c, VFF_LEFT_SIZE) == 0U)
> > +               mtk_dma_chan_write(c, VFF_INT_EN, VFF_TX_INT_EN_B);
> > +       else
> > +               mtk_dma_tx_write(&c->vc.chan);
> > +
> > +       c->stop = false;
> > +}
> > +
> > +static void mtk_dma_get_rx_size(struct mtk_chan *c)
> > +{
> 
> If the user is only one, let's span the content into where the user is.
> 
> > +       unsigned int rx_size = mtk_dma_chan_read(c, VFF_LEN);
> > +       unsigned int rdptr, wrptr, wrreg, rdreg, count;
> 
> too much variable seems a little lousy, two variables are enough
> 
> unsigned int rd, wr;
> 
> > +
> > +       rdreg = mtk_dma_chan_read(c, VFF_RPT);
> > +       wrreg = mtk_dma_chan_read(c, VFF_WPT);
> > +       rdptr = rdreg & MTK_DMA_RING_SIZE;
> > +       wrptr = wrreg & MTK_DMA_RING_SIZE;
> 
> rd = mtk_dma_chan_read(c, VFF_RPT) & MTK_DMA_RING_SIZE;
> wr = mtk_dma_chan_read(c, VFF_WPT) & MTK_DMA_RING_SIZE
> 
> > +       count = ((rdreg ^ wrreg) & MTK_DMA_RING_WRAP) ?
> > +                       (wrptr + rx_size - rdptr) : (wrptr - rdptr);
> > +
> > +       c->rx_status = count;
> 
> drop the variable count and have a direct assignment
> 
> > +
> > +       mtk_dma_chan_write(c, VFF_RPT, wrreg);
> > +}
> > +
> > +static void mtk_dma_start_rx(struct mtk_chan *c)
> > +{
> > +       struct dma_chan *chan = &c->vc.chan;
> > +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
> > +       struct mtk_dma_desc *d = c->desc;
> > +
> > +       if (mtk_dma_chan_read(c, VFF_VALID_SIZE) == 0U)
> > +               return;
> > +
> > +       if (d && vchan_next_desc(&c->vc)) {
> > +               mtk_dma_get_rx_size(c);
> > +               list_del(&d->vd.node);
> > +               vchan_cookie_complete(&d->vd);
> > +       } else {
> > +               spin_lock(&mtkd->lock);
> > +               if (list_empty(&mtkd->pending))
> > +                       list_add_tail(&c->node, &mtkd->pending);
> > +               spin_unlock(&mtkd->lock);
> > +               tasklet_schedule(&mtkd->task);
> > +       }
> > +}
> > +
> > +static void mtk_dma_reset(struct mtk_chan *c)
> > +{
> 
> If the user is only one, let's span the content into where the user is.
> 
> > +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(c->vc.chan.device);
> > +       u32 status;
> > +       int ret;
> > +
> > +       mtk_dma_chan_write(c, VFF_ADDR, 0);
> > +       mtk_dma_chan_write(c, VFF_THRE, 0);
> > +       mtk_dma_chan_write(c, VFF_LEN, 0);
> > +       mtk_dma_chan_write(c, VFF_RST, VFF_WARM_RST_B);
> > +
> > +       ret = readx_poll_timeout(readl,
> > +                                c->base + VFF_EN,
> > +                                status, status == 0, 10, 100);
> > +       if (ret) {
> > +               dev_err(c->vc.chan.device->dev,
> > +                               "dma reset: fail, timeout\n");
> > +               return;
> > +       }
> > +
> > +       if (c->cfg.direction == DMA_DEV_TO_MEM)
> > +               mtk_dma_chan_write(c, VFF_RPT, 0);
> > +       else if (c->cfg.direction == DMA_MEM_TO_DEV)
> > +               mtk_dma_chan_write(c, VFF_WPT, 0);
> 
> using switch and case statement
> 
> > +
> > +       if (mtkd->support_33bits)
> > +               mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_CLR_B);
> > +}
> > +
> > +static void mtk_dma_stop(struct mtk_chan *c)
> 
> If the user is only one, let's span the content into where the user is.
> 
> > +{
> > +       u32 status;
> > +       int ret;
> > +
> > +       mtk_dma_chan_write(c, VFF_FLUSH, VFF_FLUSH_CLR_B);
> > +       /* Wait for flush */
> > +       ret = readx_poll_timeout(readl,
> > +                                c->base + VFF_FLUSH,
> > +                                status,
> > +                                (status & VFF_FLUSH_B) != VFF_FLUSH_B,
> > +                                10, 100);
> > +       if (ret)
> > +               dev_err(c->vc.chan.device->dev,
> > +                       "dma stop: polling FLUSH fail, DEBUG=0x%x\n",
> > +                       mtk_dma_chan_read(c, VFF_DEBUG_STATUS));
> > +
> > +       /*set stop as 1 -> wait until en is 0 -> set stop as 0*/
> > +       mtk_dma_chan_write(c, VFF_STOP, VFF_STOP_B);
> > +       ret = readx_poll_timeout(readl,
> > +                                c->base + VFF_EN,
> > +                                status, status == 0, 10, 100);
> > +       if (ret)
> > +               dev_err(c->vc.chan.device->dev,
> > +                       "dma stop: polling VFF_EN fail, DEBUG=0x%x\n",
> > +                       mtk_dma_chan_read(c, VFF_DEBUG_STATUS));
> > +
> > +       mtk_dma_chan_write(c, VFF_STOP, VFF_STOP_CLR_B);
> > +       mtk_dma_chan_write(c, VFF_INT_EN, VFF_INT_EN_CLR_B);
> > +
> > +       if (c->cfg.direction == DMA_DEV_TO_MEM)
> > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> > +       else
> > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> 
> using switch and case statement
> 
> > +
> > +       c->stop = true;
> > +}
> > +
> > +/*
> > + * This callback schedules all pending channels. We could be more
> > + * clever here by postponing allocation of the real DMA channels to
> > + * this point, and freeing them when our virtual channel becomes idle.
> > + *
> > + * We would then need to deal with 'all channels in-use'
> > + */
> > +static void mtk_dma_sched(unsigned long data)
> > +{
> 
> As at the initial be said, try to make descriptors submit as fast as
> possible without involving in a tasklet. The same improvement had been
> done at mtk-hsdma.c  so you could have a reference to it first if you
> have no much idea of how to begin to improve.
> 
> > +       struct mtk_dmadev *mtkd = (struct mtk_dmadev *)data;
> > +       struct virt_dma_desc *vd;
> > +       struct mtk_chan *c;
> > +       unsigned long flags;
> > +       LIST_HEAD(head);
> > +
> > +       spin_lock_irq(&mtkd->lock);
> > +       list_splice_tail_init(&mtkd->pending, &head);
> > +       spin_unlock_irq(&mtkd->lock);
> > +
> > +       if (!list_empty(&head)) {
> > +               c = list_first_entry(&head, struct mtk_chan, node);
> > +
> > +               spin_lock_irqsave(&c->vc.lock, flags);
> > +               if (c->cfg.direction == DMA_DEV_TO_MEM) {
> > +                       list_del_init(&c->node);
> > +                       mtk_dma_start_rx(c);
> > +               } else if (c->cfg.direction == DMA_MEM_TO_DEV) {
> > +                       vd = vchan_next_desc(&c->vc);
> > +                       c->desc = to_mtk_dma_desc(&vd->tx);
> > +                       list_del_init(&c->node);
> > +                       mtk_dma_start_tx(c);
> > +               }
> > +               spin_unlock_irqrestore(&c->vc.lock, flags);
> > +       }
> > +}
> > +
> > +static int mtk_dma_alloc_chan_resources(struct dma_chan *chan)
> > +{
> > +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       int ret = -EBUSY;
> > +
> > +       pm_runtime_get_sync(mtkd->ddev.dev);
> > +
> > +       if (!mtkd->ch[chan->chan_id]) {
> > +               c->base = mtkd->mem_base[chan->chan_id]
> 
> mtkd->mem_base is unnecessary, we can directly decide c->base in the
> driver probe stage
> 
> > +               mtkd->ch[chan->chan_id] = c;
> 
> mtkd->ch is also unnecessary, the core always pass struct dma_chan
> *chan to each callback function
> 
> > +               ret = 1;
> 
> ret be 1 seems be wrong
> 
> > +       }
> > +       c->requested = false;
> > +       mtk_dma_reset(c);
> > +
> > +       return ret;
> > +}
> > +
> > +static void mtk_dma_free_chan_resources(struct dma_chan *chan)
> > +{
> > +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +
> > +       if (c->requested) {
> > +               c->requested = false;
> > +               free_irq(mtkd->dma_irq[chan->chan_id], chan);
> 
> it makes not consistent because there are not request_irq present at
> mtk_dma_alloc_chan_resources. but I'd prefer a  devm_request_irq is
> being done
> as the driver got probe.
> 
> > +       }
> > +
> > +       tasklet_kill(&mtkd->task);
> > +       tasklet_kill(&c->vc.task);
> > +
> > +       c->base = NULL;
> > +       mtkd->ch[chan->chan_id] = NULL;
> > +       vchan_free_chan_resources(&c->vc);
> > +
> > +       pm_runtime_put_sync(mtkd->ddev.dev);
> > +}
> > +
> > +static enum dma_status mtk_dma_tx_status(struct dma_chan *chan,
> > +                                        dma_cookie_t cookie,
> > +                                        struct dma_tx_state *txstate)
> > +{
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       enum dma_status ret;
> > +       unsigned long flags;
> > +
> > +       if (!txstate)
> > +               return DMA_ERROR;
> > +
> > +       ret = dma_cookie_status(chan, cookie, txstate);
> > +       spin_lock_irqsave(&c->vc.lock, flags);
> > +       if (ret == DMA_IN_PROGRESS) {
> > +               c->rx_status = mtk_dma_chan_read(c, VFF_RPT)
> > +                            & MTK_DMA_RING_SIZE;
> > +               dma_set_residue(txstate, c->rx_status);
> > +       } else if (ret == DMA_COMPLETE && c->cfg.direction == DMA_DEV_TO_MEM) {
> > +               dma_set_residue(txstate, c->rx_status);
> > +       } else {
> > +               dma_set_residue(txstate, 0);
> > +       }
> > +       spin_unlock_irqrestore(&c->vc.lock, flags);
> > +
> > +       return ret;
> > +}
> > +
> > +static struct dma_async_tx_descriptor *mtk_dma_prep_slave_sg
> > +       (struct dma_chan *chan, struct scatterlist *sgl,
> > +       unsigned int sglen,     enum dma_transfer_direction dir,
> > +       unsigned long tx_flags, void *context)
> > +{
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       struct scatterlist *sgent;
> > +       struct mtk_dma_desc *d;
> > +       struct mtk_dma_sg *sg;
> > +       unsigned int size, i, j, en;
> > +
> > +       en = 1;
> > +
> > +       if ((dir != DMA_DEV_TO_MEM) &&
> > +               (dir != DMA_MEM_TO_DEV)) {
> > +               dev_err(chan->device->dev, "bad direction\n");
> > +               return NULL;
> > +       }
> > +
> > +       /* Now allocate and setup the descriptor. */
> > +       d = kzalloc(sizeof(*d) + sglen * sizeof(d->sg[0]), GFP_ATOMIC);
> > +       if (!d)
> > +               return NULL;
> > +
> > +       d->dir = dir;
> > +
> > +       j = 0;
> > +       for_each_sg(sgl, sgent, sglen, i) {
> > +               d->sg[j].addr = sg_dma_address(sgent);
> > +               d->sg[j].en = en;
> > +               d->sg[j].fn = sg_dma_len(sgent) / en;
> > +               j++;
> > +       }
> > +
> > +       d->sglen = j;
> > +
> > +       if (dir == DMA_MEM_TO_DEV) {
> > +               for (size = i = 0; i < d->sglen; i++) {
> > +                       sg = &d->sg[i];
> > +                       size += sg->en * sg->fn;
> > +               }
> > +               d->len = size;
> > +       }
> > +
> 
> The driver always only handles data move for the single contiguous
> area, but it seems the callback must provide the scatter-gather
> function to the dmaegine. otherwise, why is the callback be called
> device_prep_slave_sg?
> 

because in 8250 UART native code, call the device_prep_slave_sg. we just
use one ring buffer.

> > +       return vchan_tx_prep(&c->vc, &d->vd, tx_flags);
> > +}
> > +
> > +static void mtk_dma_issue_pending(struct dma_chan *chan)
> > +{
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       struct virt_dma_desc *vd;
> > +       struct mtk_dmadev *mtkd;
> > +       unsigned long flags;
> > +
> > +       spin_lock_irqsave(&c->vc.lock, flags);
> > +       if (c->cfg.direction == DMA_DEV_TO_MEM) {
> > +               mtkd = to_mtk_dma_dev(chan->device);
> 
> mtkd can be dropped as it seems no users
> 
> > +               if (vchan_issue_pending(&c->vc) && !c->desc) {
> > +                       vd = vchan_next_desc(&c->vc);
> > +                       c->desc = to_mtk_dma_desc(&vd->tx);
> > +               }
> > +       } else if (c->cfg.direction == DMA_MEM_TO_DEV) {
> > +               if (vchan_issue_pending(&c->vc) && !c->desc) {
> > +                       vd = vchan_next_desc(&c->vc);
> > +                       c->desc = to_mtk_dma_desc(&vd->tx);
> > +                       mtk_dma_start_tx(c);
> > +               }
> > +       }
> > +       spin_unlock_irqrestore(&c->vc.lock, flags);
> > +}
> > +
> > +static irqreturn_t mtk_dma_rx_interrupt(int irq, void *dev_id)
> > +{
> > +       struct dma_chan *chan = (struct dma_chan *)dev_id;
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       unsigned long flags;
> > +
> > +       spin_lock_irqsave(&c->vc.lock, flags);
> > +       mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> > +
> > +       mtk_dma_start_rx(c);
> > +
> > +       spin_unlock_irqrestore(&c->vc.lock, flags);
> > +
> > +       return IRQ_HANDLED;
> > +}
> > +
> > +static irqreturn_t mtk_dma_tx_interrupt(int irq, void *dev_id)
> > +{
> > +       struct dma_chan *chan = (struct dma_chan *)dev_id;
> > +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(chan->device);
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       struct mtk_dma_desc *d = c->desc;
> > +       unsigned long flags;
> > +
> > +       spin_lock_irqsave(&c->vc.lock, flags);
> > +       if (d->len != 0U) {
> > +               list_add_tail(&c->node, &mtkd->pending);
> > +               tasklet_schedule(&mtkd->task);
> > +       } else {
> > +               list_del(&d->vd.node);
> > +               vchan_cookie_complete(&d->vd);
> > +       }
> > +       spin_unlock_irqrestore(&c->vc.lock, flags);
> > +
> > +       mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> > +
> > +       return IRQ_HANDLED;
> > +}
> > +
> > +static int mtk_dma_slave_config(struct dma_chan *chan,
> > +                               struct dma_slave_config *cfg)
> > +{
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(c->vc.chan.device);
> > +       int ret;
> > +
> > +       c->cfg = *cfg;
> > +
> > +       if (cfg->direction == DMA_DEV_TO_MEM) {
> > +               unsigned int rx_len = cfg->src_addr_width * 1024;
> 
> it seems you should use cfg->src_port_window_size as the comments explains
> 
> * @src_port_window_size: The length of the register area in words the data need
>  * to be accessed on the device side. It is only used for devices which is using
>  * an area instead of a single register to receive the data. Typically the DMA
>  * loops in this area in order to transfer the data.
>  * @dst_port_window_size: same as src_port_window_size but for the destination
>  * port.
> 

in 8250 UART native code, will set the parameter. if want to modify
this, i think that maybe at next kernel release, we can modify it. i
suggest that not modify it at this patch. because it relate of 8250 uart
code. thanks.

> > +
> > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->src_addr);
> > +               mtk_dma_chan_write(c, VFF_LEN, rx_len);
> > +               mtk_dma_chan_write(c, VFF_THRE, VFF_RX_THRE(rx_len));
> > +               mtk_dma_chan_write(c,
> > +                                  VFF_INT_EN, VFF_RX_INT_EN0_B
> > +                                  | VFF_RX_INT_EN1_B);
> > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> 
> I'd prefer to move those channel interrupt enablement to
> .device_alloc_chan_resources
> and related disablement to .device_free_chan_resources
> 

i think that, first need set the config to HW, and the enable the DMA. 

> > +
> > +               if (!c->requested) {
> > +                       c->requested = true;
> > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > +                                         mtk_dma_rx_interrupt,
> > +                                         IRQF_TRIGGER_NONE,
> > +                                         KBUILD_MODNAME, chan);
> 
> ISR registration usually happens as the driver got probe, it can give
> the system more flexibility to manage such IRQ affinity on the fly.
> 

i will move the request irq to alloc channel.

> > +                       if (ret < 0) {
> > +                               dev_err(chan->device->dev, "Can't request rx dma IRQ\n");
> > +                               return -EINVAL;
> > +                       }
> > +               }
> > +       } else if (cfg->direction == DMA_MEM_TO_DEV)    {
> > +               unsigned int tx_len = cfg->dst_addr_width * 1024;
> 
> Ditto as above, it seems you should use cfg->dst_port_window_size
> 
> > +
> > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->dst_addr);
> > +               mtk_dma_chan_write(c, VFF_LEN, tx_len);
> > +               mtk_dma_chan_write(c, VFF_THRE, VFF_TX_THRE(tx_len));
> > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> 
> ditto, I'd prefer to move those channel interrupt enablement to
> .device_alloc_chan_resources and related disablement to
> .device_free_chan_resources
> 
> > +
> > +               if (!c->requested) {
> > +                       c->requested = true;
> > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > +                                         mtk_dma_tx_interrupt,
> > +                                         IRQF_TRIGGER_NONE,
> > +                                         KBUILD_MODNAME, chan);
> 
> ditto, we can request ISR with devm_request_irq in the driver got
> probe and trim the c->request member
> 
> > +                       if (ret < 0) {
> > +                               dev_err(chan->device->dev, "Can't request tx dma IRQ\n");
> > +                               return -EINVAL;
> > +                       }
> > +               }
> > +       }
> > +
> > +       if (mtkd->support_33bits)
> > +               mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_B);
> > +
> > +       if (mtk_dma_chan_read(c, VFF_EN) != VFF_EN_B) {
> > +               dev_err(chan->device->dev,
> > +                       "config dma dir[%d] fail\n", cfg->direction);
> > +               return -EINVAL;
> > +       }
> > +
> > +       return 0;
> > +}
> > +
> > +static int mtk_dma_terminate_all(struct dma_chan *chan)
> > +{
> > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > +       unsigned long flags;
> > +
> > +       spin_lock_irqsave(&c->vc.lock, flags);
> > +       list_del_init(&c->node);
> > +       mtk_dma_stop(c);
> > +       spin_unlock_irqrestore(&c->vc.lock, flags);
> > +
> > +       return 0;
> > +}
> > +
> > +static int mtk_dma_device_pause(struct dma_chan *chan)
> > +{
> > +       /* just for check caps pass */
> > +       return -EINVAL;
> 
> always return error code seems not the client driver wants us to do.
> 
> maybe if the hardware doesn't support pause, we can make a software
> pause, that waits until all active descriptors in hardware done, then
> disable interrupt and then stop handling the following vd in the
> vchan.
> 
> > +}

the code can't run. just for 8250 native code to check the function
pointer. in the future, if the function useful, we can realize. thanks.

> > +
> > +static int mtk_dma_device_resume(struct dma_chan *chan)
> > +{
> > +       /* just for check caps pass */
> > +       return -EINVAL;
> 
> similar to the above
> 
> > +}
> > +
> > +static void mtk_dma_free(struct mtk_dmadev *mtkd)
> > +{
> > +       tasklet_kill(&mtkd->task);
> > +       while (list_empty(&mtkd->ddev.channels) == 0) {
> !list_empty(&mtkd->ddev.channels)
> > +               struct mtk_chan *c = list_first_entry(&mtkd->ddev.channels,
> > +                       struct mtk_chan, vc.chan.device_node);
> > +
> > +               list_del(&c->vc.chan.device_node);
> > +               tasklet_kill(&c->vc.task);
> > +               devm_kfree(mtkd->ddev.dev, c);
> 
> no need to call devm_kfree, the core would help do this
> 
> > +       }
> > +}
> > +
> > +static const struct of_device_id mtk_uart_dma_match[] = {
> > +       { .compatible = "mediatek,mt6577-uart-dma", },
> > +       { /* sentinel */ },
> > +};
> > +MODULE_DEVICE_TABLE(of, mtk_uart_dma_match);
> > +
> > +static int mtk_apdma_probe(struct platform_device *pdev)
> > +{
> > +       struct mtk_dmadev *mtkd;
> > +       struct resource *res;
> > +       struct mtk_chan *c;
> > +       unsigned int i;
> > +       int rc;
> > +
> > +       mtkd = devm_kzalloc(&pdev->dev, sizeof(*mtkd), GFP_KERNEL);
> > +       if (!mtkd)
> > +               return -ENOMEM;
> > +
> > +       for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
> > +               res = platform_get_resource(pdev, IORESOURCE_MEM, i);
> > +               if (!res)
> > +                       return -ENODEV;
> > +               mtkd->mem_base[i] = devm_ioremap_resource(&pdev->dev, res);
> > +               if (IS_ERR(mtkd->mem_base[i]))
> > +                       return PTR_ERR(mtkd->mem_base[i]);
> > +       }
> > +
> > +       for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
> > +               mtkd->dma_irq[i] = platform_get_irq(pdev, i);
> > +               if ((int)mtkd->dma_irq[i] < 0) {
> > +                       dev_err(&pdev->dev, "failed to get IRQ[%d]\n", i);
> > +                       return -EINVAL;
> > +               }
> > +       }
> > +
> > +       mtkd->clk = devm_clk_get(&pdev->dev, NULL);
> > +       if (IS_ERR(mtkd->clk)) {
> > +               dev_err(&pdev->dev, "No clock specified\n");
> > +               return PTR_ERR(mtkd->clk);
> > +       }
> > +
> > +       if (of_property_read_bool(pdev->dev.of_node, "dma-33bits")) {
> > +               dev_info(&pdev->dev, "Support dma 33bits\n");
> > +               mtkd->support_33bits = true;
> > +       }
> > +
> > +       if (mtkd->support_33bits)
> > +               rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(33));
> > +       else
> > +               rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
> 
>  rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32 |
> mtkd->support_33bits));
> 
> > +       if (rc)
> > +               return rc;
> > +
> > +       dma_cap_set(DMA_SLAVE, mtkd->ddev.cap_mask);
> > +       mtkd->ddev.device_alloc_chan_resources = mtk_dma_alloc_chan_resources;
> > +       mtkd->ddev.device_free_chan_resources = mtk_dma_free_chan_resources;
> > +       mtkd->ddev.device_tx_status = mtk_dma_tx_status;
> > +       mtkd->ddev.device_issue_pending = mtk_dma_issue_pending;
> > +       mtkd->ddev.device_prep_slave_sg = mtk_dma_prep_slave_sg;
> > +       mtkd->ddev.device_config = mtk_dma_slave_config;
> > +       mtkd->ddev.device_pause = mtk_dma_device_pause;
> > +       mtkd->ddev.device_resume = mtk_dma_device_resume;
> > +       mtkd->ddev.device_terminate_all = mtk_dma_terminate_all;
> > +       mtkd->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE);
> > +       mtkd->ddev.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_1_BYTE);
> > +       mtkd->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
> > +       mtkd->ddev.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
> > +       mtkd->ddev.dev = &pdev->dev;
> > +       INIT_LIST_HEAD(&mtkd->ddev.channels);
> > +       INIT_LIST_HEAD(&mtkd->pending);
> > +
> > +       spin_lock_init(&mtkd->lock);
> > +       tasklet_init(&mtkd->task, mtk_dma_sched, (unsigned long)mtkd);
> > +
> > +       mtkd->dma_requests = MTK_APDMA_DEFAULT_REQUESTS;
> > +       if (of_property_read_u32(pdev->dev.of_node,
> > +                                "dma-requests", &mtkd->dma_requests)) {
> > +               dev_info(&pdev->dev,
> > +                        "Missing dma-requests property, using %u.\n",
> > +                        MTK_APDMA_DEFAULT_REQUESTS);
> > +       }
> > +
> > +       for (i = 0; i < MTK_APDMA_CHANNELS; i++) {
> > +               c = devm_kzalloc(mtkd->ddev.dev, sizeof(*c), GFP_KERNEL);
> > +               if (!c)
> > +                       goto err_no_dma;
> > +
> > +               c->vc.desc_free = mtk_dma_desc_free;
> > +               vchan_init(&c->vc, &mtkd->ddev);
> > +               INIT_LIST_HEAD(&c->node);
> > +       }
> > +
> > +       pm_runtime_enable(&pdev->dev);
> > +       pm_runtime_set_active(&pdev->dev);
> > +
> > +       rc = dma_async_device_register(&mtkd->ddev);
> > +       if (rc)
> > +               goto rpm_disable;
> > +
> > +       platform_set_drvdata(pdev, mtkd);
> > +
> > +       if (pdev->dev.of_node) {
> > +               /* Device-tree DMA controller registration */
> > +               rc = of_dma_controller_register(pdev->dev.of_node,
> > +                                               of_dma_xlate_by_chan_id,
> > +                                               mtkd);
> > +               if (rc)
> > +                       goto dma_remove;
> > +       }
> > +
> > +       return rc;
> > +
> > +dma_remove:
> > +       dma_async_device_unregister(&mtkd->ddev);
> > +rpm_disable:
> > +       pm_runtime_disable(&pdev->dev);
> > +err_no_dma:
> > +       mtk_dma_free(mtkd);
> > +       return rc;
> > +}
> > +
> > +static int mtk_apdma_remove(struct platform_device *pdev)
> > +{
> > +       struct mtk_dmadev *mtkd = platform_get_drvdata(pdev);
> > +
> > +       if (pdev->dev.of_node)
> > +               of_dma_controller_free(pdev->dev.of_node);
> > +
> > +       pm_runtime_disable(&pdev->dev);
> > +       pm_runtime_put_noidle(&pdev->dev);
> > +
> > +       dma_async_device_unregister(&mtkd->ddev);
> > +
> > +       mtk_dma_free(mtkd);
> > +
> > +       return 0;
> > +}
> > +
> > +#ifdef CONFIG_PM_SLEEP
> > +static int mtk_dma_suspend(struct device *dev)
> > +{
> > +       struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
> > +
> > +       if (!pm_runtime_suspended(dev))
> > +               clk_disable_unprepare(mtkd->clk);
> > +
> > +       return 0;
> > +}
> > +
> > +static int mtk_dma_resume(struct device *dev)
> > +{
> > +       int ret;
> > +       struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
> > +
> > +       if (!pm_runtime_suspended(dev)) {
> > +               ret = clk_prepare_enable(mtkd->clk);
> > +               if (ret)
> > +                       return ret;
> > +       }
> > +
> > +       return 0;
> > +}
> > +#endif /* CONFIG_PM_SLEEP */
> > +
> > +#ifdef CONFIG_PM
> > +static int mtk_dma_runtime_suspend(struct device *dev)
> > +{
> > +       struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
> > +
> > +       clk_disable_unprepare(mtkd->clk);
> > +
> > +       return 0;
> > +}
> > +
> > +static int mtk_dma_runtime_resume(struct device *dev)
> > +{
> > +       int ret;
> > +       struct mtk_dmadev *mtkd = dev_get_drvdata(dev);
> > +
> > +       ret = clk_prepare_enable(mtkd->clk);
> > +       if (ret)
> > +               return ret;
> > +
> > +       return 0;
> > +}
> > +#endif /* CONFIG_PM */
> > +
> > +static const struct dev_pm_ops mtk_dma_pm_ops = {
> > +       SET_SYSTEM_SLEEP_PM_OPS(mtk_dma_suspend, mtk_dma_resume)
> > +       SET_RUNTIME_PM_OPS(mtk_dma_runtime_suspend,
> > +                          mtk_dma_runtime_resume, NULL)
> > +};
> > +
> > +static struct platform_driver mtk_dma_driver = {
> 
> mtk_dma is much general and all functions and structures in the driver
> should be all consistent.  I'd prefer to have all naming starts with
> mtk_uart_apdma.
> 

the function name and parameters' name, i will modify it. but before the
8250_mtk.c and the Doc. are recorded. if modify file name and Kconfig,
will bring about the disorder. i suggest that after the patch is
recorded, modify this. thanks.

> > +       .probe  = mtk_apdma_probe,
> 
> such  as
> mtk_uart_apdma_probe
> 
> > +       .remove = mtk_apdma_remove,
> 
> mtk_uart_apdma_remove
> 
> > +       .driver = {
> > +               .name           = KBUILD_MODNAME,
> > +               .pm             = &mtk_dma_pm_ops,
> 
> mtk_uart_apdma_pm_ops
> 
> > +               .of_match_table = of_match_ptr(mtk_uart_dma_match),
> 
> mtk_uart_apdma_match
> 
> > +       },
> > +};
> > +
> > +module_platform_driver(mtk_dma_driver);
> 
> mtk_uart_apdma_driver
> 
> > +
> > +MODULE_DESCRIPTION("MediaTek UART APDMA Controller Driver");
> > +MODULE_AUTHOR("Long Cheng <long.cheng@mediatek.com>");
> > +MODULE_LICENSE("GPL v2");
> > +
> > diff --git a/drivers/dma/mediatek/Kconfig b/drivers/dma/mediatek/Kconfig
> > index 27bac0b..d399624 100644
> > --- a/drivers/dma/mediatek/Kconfig
> > +++ b/drivers/dma/mediatek/Kconfig
> > @@ -1,4 +1,15 @@
> >
> > +config DMA_MTK_UART
> 
> MTK_UART_APDMA to align the other drivers
> 
> > +       tristate "MediaTek SoCs APDMA support for UART"
> > +       depends on OF && SERIAL_8250_MT6577
> > +       select DMA_ENGINE
> > +       select DMA_VIRTUAL_CHANNELS
> > +       help
> > +         Support for the UART DMA engine found on MediaTek MTK SoCs.
> > +         when 8250 mtk uart is enabled, and if you want to using DMA,
> 
> 8250 mtk uart should be changed to SERIAL_8250_MT6577 to be more intuitive
> 
> > +         you can enable the config. the DMA engine just only be used
> > +         with MediaTek Socs.
> 
> SoCs
> 
> > +
> >  config MTK_HSDMA
> >         tristate "MediaTek High-Speed DMA controller support"
> >         depends on ARCH_MEDIATEK || COMPILE_TEST
> > diff --git a/drivers/dma/mediatek/Makefile b/drivers/dma/mediatek/Makefile
> > index 6e778f8..2f2efd9 100644
> > --- a/drivers/dma/mediatek/Makefile
> > +++ b/drivers/dma/mediatek/Makefile
> > @@ -1 +1,2 @@
> > +obj-$(CONFIG_DMA_MTK_UART) += 8250_mtk_dma.o
> 
> obj-$(CONFIG_MTK_UART_APDMA) += mtk-uart-apdma.o
> to align the other dirvers
> 
> >  obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o
> > --
> > 1.7.9.5
> >



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 1/2] dmaengine: 8250_mtk_dma: add Mediatek uart DMA support

[Sean Wang]

On Thu, Dec 13, 2018 at 3:36 AM Long Cheng <long.cheng@mediatek.com> wrote:

Hope those comments did not get a response that means they're fine with you.

< ... >

> > > +struct mtk_dmadev {
> > > +       struct dma_device ddev;
> > > +       void __iomem *mem_base[MTK_APDMA_CHANNELS];
> > > +       spinlock_t lock; /* dma dev lock */
> > > +       struct tasklet_struct task;
> >
> > we can drop tasklet and instead allows descriptors to be handled as
> > fast as possible.
> > similar suggestions have been made in the other dmaengine [1] and mtk-hsdma.c
> >
>
> OK, i will remove these, and improve it.
>

Thanks, that would be great.

> > [1] https://lkml.org/lkml/2018/11/11/146
> >
> > > +       struct list_head pending;
> > > +       struct clk *clk;
> > > +       unsigned int dma_requests;
> > > +       bool support_33bits;
> > > +       unsigned int dma_irq[MTK_APDMA_CHANNELS];
> > > +       struct mtk_chan *ch[MTK_APDMA_CHANNELS];
> > > +};
> > > +

< ... >

> > > +static struct dma_async_tx_descriptor *mtk_dma_prep_slave_sg
> > > +       (struct dma_chan *chan, struct scatterlist *sgl,
> > > +       unsigned int sglen,     enum dma_transfer_direction dir,
> > > +       unsigned long tx_flags, void *context)
> > > +{
> > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > +       struct scatterlist *sgent;
> > > +       struct mtk_dma_desc *d;
> > > +       struct mtk_dma_sg *sg;
> > > +       unsigned int size, i, j, en;
> > > +
> > > +       en = 1;
> > > +
> > > +       if ((dir != DMA_DEV_TO_MEM) &&
> > > +               (dir != DMA_MEM_TO_DEV)) {
> > > +               dev_err(chan->device->dev, "bad direction\n");
> > > +               return NULL;
> > > +       }
> > > +
> > > +       /* Now allocate and setup the descriptor. */
> > > +       d = kzalloc(sizeof(*d) + sglen * sizeof(d->sg[0]), GFP_ATOMIC);
> > > +       if (!d)
> > > +               return NULL;
> > > +
> > > +       d->dir = dir;
> > > +
> > > +       j = 0;
> > > +       for_each_sg(sgl, sgent, sglen, i) {
> > > +               d->sg[j].addr = sg_dma_address(sgent);
> > > +               d->sg[j].en = en;
> > > +               d->sg[j].fn = sg_dma_len(sgent) / en;
> > > +               j++;
> > > +       }
> > > +
> > > +       d->sglen = j;
> > > +
> > > +       if (dir == DMA_MEM_TO_DEV) {
> > > +               for (size = i = 0; i < d->sglen; i++) {
> > > +                       sg = &d->sg[i];
> > > +                       size += sg->en * sg->fn;
> > > +               }
> > > +               d->len = size;
> > > +       }
> > > +
> >
> > The driver always only handles data move for the single contiguous
> > area, but it seems the callback must provide the scatter-gather
> > function to the dmaegine. otherwise, why is the callback be called
> > device_prep_slave_sg?
> >
>
> because in 8250 UART native code, call the device_prep_slave_sg. we just
> use one ring buffer.
>

If it really did specifically for UART, you should show the function
only can handle only one entry in sg for the DMA in a few comments and
a sanity check for these invalid requests (more one entries in sg).
Otherwise, the hardware will get a failure and even function doesn't
complain or warn anything if more one entries in sg requested in.
Additionally, the code can be simplified much if it's just for the
specific use case.

> > > +       return vchan_tx_prep(&c->vc, &d->vd, tx_flags);
> > > +}
> > > +
> > > +static void mtk_dma_issue_pending(struct dma_chan *chan)
> > > +{
> > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > +       struct virt_dma_desc *vd;
> > > +       struct mtk_dmadev *mtkd;
> > > +       unsigned long flags;
> > > +
> > > +       spin_lock_irqsave(&c->vc.lock, flags);
> > > +       if (c->cfg.direction == DMA_DEV_TO_MEM) {
> > > +               mtkd = to_mtk_dma_dev(chan->device);
> >
> > mtkd can be dropped as it seems no users
> >

< ... >

> > > +static int mtk_dma_slave_config(struct dma_chan *chan,
> > > +                               struct dma_slave_config *cfg)
> > > +{
> > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(c->vc.chan.device);
> > > +       int ret;
> > > +
> > > +       c->cfg = *cfg;
> > > +
> > > +       if (cfg->direction == DMA_DEV_TO_MEM) {
> > > +               unsigned int rx_len = cfg->src_addr_width * 1024;
> >
> > it seems you should use cfg->src_port_window_size as the comments explains
> >
> > * @src_port_window_size: The length of the register area in words the data need
> >  * to be accessed on the device side. It is only used for devices which is using
> >  * an area instead of a single register to receive the data. Typically the DMA
> >  * loops in this area in order to transfer the data.
> >  * @dst_port_window_size: same as src_port_window_size but for the destination
> >  * port.
> >
>
> in 8250 UART native code, will set the parameter. if want to modify
> this, i think that maybe at next kernel release, we can modify it. i
> suggest that not modify it at this patch. because it relate of 8250 uart
> code. thanks.
>

You can fix it in the next version and a separate follow-up patch for
the client driver.

> > > +
> > > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->src_addr);
> > > +               mtk_dma_chan_write(c, VFF_LEN, rx_len);
> > > +               mtk_dma_chan_write(c, VFF_THRE, VFF_RX_THRE(rx_len));
> > > +               mtk_dma_chan_write(c,
> > > +                                  VFF_INT_EN, VFF_RX_INT_EN0_B
> > > +                                  | VFF_RX_INT_EN1_B);
> > > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> > > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> >
> > I'd prefer to move those channel interrupt enablement to
> > .device_alloc_chan_resources
> > and related disablement to .device_free_chan_resources
> >
>
> i think that, first need set the config to HW, and the enable the DMA.
>

I've read through the client driver and the dmaengine, I probably know
how interaction they work and find out there is something you seem
completely make a wrong.

You can't do enable DMA with enabling VFF here. That causes a big
problem, DMA would self decide to move data and not managed and issued
by the dmaengine framework. For instance in DMA Tx path, because you
enable the DMA and DMA  buffer (VFF) and UART Tx ring uses the same
memory area,  DMA would self start to move data once data from
userland go in Tx ring even without being issued by dmaengine.

Instead, you should ensure all descriptors are being batched by
.device_prep_slave_sg and DMA does not start moving data until
.device_issue_pending done and once descriptors are issued, DMA
hardware or software have to do it as fast as possible.

> > > +
> > > +               if (!c->requested) {
> > > +                       c->requested = true;
> > > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > > +                                         mtk_dma_rx_interrupt,
> > > +                                         IRQF_TRIGGER_NONE,
> > > +                                         KBUILD_MODNAME, chan);
> >
> > ISR registration usually happens as the driver got probe, it can give
> > the system more flexibility to manage such IRQ affinity on the fly.
> >
>
> i will move the request irq to alloc channel.
>

why don't let it done in driver probe?

> > > +                       if (ret < 0) {
> > > +                               dev_err(chan->device->dev, "Can't request rx dma IRQ\n");
> > > +                               return -EINVAL;
> > > +                       }
> > > +               }
> > > +       } else if (cfg->direction == DMA_MEM_TO_DEV)    {
> > > +               unsigned int tx_len = cfg->dst_addr_width * 1024;
> >
> > Ditto as above, it seems you should use cfg->dst_port_window_size
> >
> > > +
> > > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->dst_addr);
> > > +               mtk_dma_chan_write(c, VFF_LEN, tx_len);
> > > +               mtk_dma_chan_write(c, VFF_THRE, VFF_TX_THRE(tx_len));
> > > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> > > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> >
> > ditto, I'd prefer to move those channel interrupt enablement to
> > .device_alloc_chan_resources and related disablement to
> > .device_free_chan_resources
> >
> > > +
> > > +               if (!c->requested) {
> > > +                       c->requested = true;
> > > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > > +                                         mtk_dma_tx_interrupt,
> > > +                                         IRQF_TRIGGER_NONE,
> > > +                                         KBUILD_MODNAME, chan);
> >
> > ditto, we can request ISR with devm_request_irq in the driver got
> > probe and trim the c->request member
> >
> > > +                       if (ret < 0) {
> > > +                               dev_err(chan->device->dev, "Can't request tx dma IRQ\n");
> > > +                               return -EINVAL;
> > > +                       }
> > > +               }
> > > +       }
> > > +
> > > +       if (mtkd->support_33bits)
> > > +               mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_B);
> > > +
> > > +       if (mtk_dma_chan_read(c, VFF_EN) != VFF_EN_B) {
> > > +               dev_err(chan->device->dev,
> > > +                       "config dma dir[%d] fail\n", cfg->direction);
> > > +               return -EINVAL;
> > > +       }
> > > +
> > > +       return 0;
> > > +}
> > > +
> > > +static int mtk_dma_terminate_all(struct dma_chan *chan)
> > > +{
> > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > +       unsigned long flags;
> > > +
> > > +       spin_lock_irqsave(&c->vc.lock, flags);
> > > +       list_del_init(&c->node);
> > > +       mtk_dma_stop(c);
> > > +       spin_unlock_irqrestore(&c->vc.lock, flags);
> > > +
> > > +       return 0;
> > > +}
> > > +
> > > +static int mtk_dma_device_pause(struct dma_chan *chan)
> > > +{
> > > +       /* just for check caps pass */
> > > +       return -EINVAL;
> >
> > always return error code seems not the client driver wants us to do.
> >
> > maybe if the hardware doesn't support pause, we can make a software
> > pause, that waits until all active descriptors in hardware done, then
> > disable interrupt and then stop handling the following vd in the
> > vchan.
> >
> > > +}
>
> the code can't run. just for 8250 native code to check the function
> pointer. in the future, if the function useful, we can realize. thanks.
>

Always return an error code looks like it's a faked function just to
pass the criteria check. It seems not a good idea.

> > > +
> > > +static int mtk_dma_device_resume(struct dma_chan *chan)
> > > +{
> > > +       /* just for check caps pass */
> > > +       return -EINVAL;

< ... >

> > > +static struct platform_driver mtk_dma_driver = {
> >
> > mtk_dma is much general and all functions and structures in the driver
> > should be all consistent.  I'd prefer to have all naming starts with
> > mtk_uart_apdma.
> >
>
> the function name and parameters' name, i will modify it. but before the
> 8250_mtk.c and the Doc. are recorded. if modify file name and Kconfig,
> will bring about the disorder. i suggest that after the patch is
> recorded, modify this. thanks.
>

We can do it in separate patches and in a logical order for the
changes required across different subsystems.

> > > +       .probe  = mtk_apdma_probe,
> >
> > such  as
> > mtk_uart_apdma_probe
> >
> > > +       .remove = mtk_apdma_remove,
> >
> > mtk_uart_apdma_remove
> >
> > > +       .driver = {
> > > +               .name           = KBUILD_MODNAME,
> > > +               .pm             = &mtk_dma_pm_ops,
> >
> > mtk_uart_apdma_pm_ops
> >
> > > +               .of_match_table = of_match_ptr(mtk_uart_dma_match),
> >
> > mtk_uart_apdma_match
> >
> > > +       },
> > > +};
> > > +
> > > +module_platform_driver(mtk_dma_driver);
> >
> > mtk_uart_apdma_driver
> >
> > > +
> > > +MODULE_DESCRIPTION("MediaTek UART APDMA Controller Driver");
> > > +MODULE_AUTHOR("Long Cheng <long.cheng@mediatek.com>");
> > > +MODULE_LICENSE("GPL v2");
> > > +
> > > diff --git a/drivers/dma/mediatek/Kconfig b/drivers/dma/mediatek/Kconfig
> > > index 27bac0b..d399624 100644
> > > --- a/drivers/dma/mediatek/Kconfig
> > > +++ b/drivers/dma/mediatek/Kconfig
> > > @@ -1,4 +1,15 @@
> > >
> > > +config DMA_MTK_UART
> >
> > MTK_UART_APDMA to align the other drivers
> >
> > > +       tristate "MediaTek SoCs APDMA support for UART"
> > > +       depends on OF && SERIAL_8250_MT6577
> > > +       select DMA_ENGINE
> > > +       select DMA_VIRTUAL_CHANNELS
> > > +       help
> > > +         Support for the UART DMA engine found on MediaTek MTK SoCs.
> > > +         when 8250 mtk uart is enabled, and if you want to using DMA,
> >
> > 8250 mtk uart should be changed to SERIAL_8250_MT6577 to be more intuitive
> >
> > > +         you can enable the config. the DMA engine just only be used
> > > +         with MediaTek Socs.
> >
> > SoCs
> >
> > > +
> > >  config MTK_HSDMA
> > >         tristate "MediaTek High-Speed DMA controller support"
> > >         depends on ARCH_MEDIATEK || COMPILE_TEST
> > > diff --git a/drivers/dma/mediatek/Makefile b/drivers/dma/mediatek/Makefile
> > > index 6e778f8..2f2efd9 100644
> > > --- a/drivers/dma/mediatek/Makefile
> > > +++ b/drivers/dma/mediatek/Makefile
> > > @@ -1 +1,2 @@
> > > +obj-$(CONFIG_DMA_MTK_UART) += 8250_mtk_dma.o
> >
> > obj-$(CONFIG_MTK_UART_APDMA) += mtk-uart-apdma.o
> > to align the other dirvers
> >
> > >  obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o
> > > --
> > > 1.7.9.5
> > >
>
>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 1/2] dmaengine: 8250_mtk_dma: add Mediatek uart DMA support

[Long Cheng]

On Fri, 2018-12-14 at 12:09 -0800, Sean Wang wrote:

thanks for your reply.

> On Thu, Dec 13, 2018 at 3:36 AM Long Cheng <long.cheng@mediatek.com> wrote:
> 
> Hope those comments did not get a response that means they're fine with you.
> 
> < ... >
> 
> > > > +struct mtk_dmadev {
> > > > +       struct dma_device ddev;
> > > > +       void __iomem *mem_base[MTK_APDMA_CHANNELS];
> > > > +       spinlock_t lock; /* dma dev lock */
> > > > +       struct tasklet_struct task;
> > >
> > > we can drop tasklet and instead allows descriptors to be handled as
> > > fast as possible.
> > > similar suggestions have been made in the other dmaengine [1] and mtk-hsdma.c
> > >
> >
> > OK, i will remove these, and improve it.
> >
> 
> Thanks, that would be great.
> 
> > > [1] https://lkml.org/lkml/2018/11/11/146
> > >
> > > > +       struct list_head pending;
> > > > +       struct clk *clk;
> > > > +       unsigned int dma_requests;
> > > > +       bool support_33bits;
> > > > +       unsigned int dma_irq[MTK_APDMA_CHANNELS];
> > > > +       struct mtk_chan *ch[MTK_APDMA_CHANNELS];
> > > > +};
> > > > +
> 
> < ... >
> 
> > > > +static struct dma_async_tx_descriptor *mtk_dma_prep_slave_sg
> > > > +       (struct dma_chan *chan, struct scatterlist *sgl,
> > > > +       unsigned int sglen,     enum dma_transfer_direction dir,
> > > > +       unsigned long tx_flags, void *context)
> > > > +{
> > > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > > +       struct scatterlist *sgent;
> > > > +       struct mtk_dma_desc *d;
> > > > +       struct mtk_dma_sg *sg;
> > > > +       unsigned int size, i, j, en;
> > > > +
> > > > +       en = 1;
> > > > +
> > > > +       if ((dir != DMA_DEV_TO_MEM) &&
> > > > +               (dir != DMA_MEM_TO_DEV)) {
> > > > +               dev_err(chan->device->dev, "bad direction\n");
> > > > +               return NULL;
> > > > +       }
> > > > +
> > > > +       /* Now allocate and setup the descriptor. */
> > > > +       d = kzalloc(sizeof(*d) + sglen * sizeof(d->sg[0]), GFP_ATOMIC);
> > > > +       if (!d)
> > > > +               return NULL;
> > > > +
> > > > +       d->dir = dir;
> > > > +
> > > > +       j = 0;
> > > > +       for_each_sg(sgl, sgent, sglen, i) {
> > > > +               d->sg[j].addr = sg_dma_address(sgent);
> > > > +               d->sg[j].en = en;
> > > > +               d->sg[j].fn = sg_dma_len(sgent) / en;
> > > > +               j++;
> > > > +       }
> > > > +
> > > > +       d->sglen = j;
> > > > +
> > > > +       if (dir == DMA_MEM_TO_DEV) {
> > > > +               for (size = i = 0; i < d->sglen; i++) {
> > > > +                       sg = &d->sg[i];
> > > > +                       size += sg->en * sg->fn;
> > > > +               }
> > > > +               d->len = size;
> > > > +       }
> > > > +
> > >
> > > The driver always only handles data move for the single contiguous
> > > area, but it seems the callback must provide the scatter-gather
> > > function to the dmaegine. otherwise, why is the callback be called
> > > device_prep_slave_sg?
> > >
> >
> > because in 8250 UART native code, call the device_prep_slave_sg. we just
> > use one ring buffer.
> >
> 
> If it really did specifically for UART, you should show the function
> only can handle only one entry in sg for the DMA in a few comments and
> a sanity check for these invalid requests (more one entries in sg).
> Otherwise, the hardware will get a failure and even function doesn't
> complain or warn anything if more one entries in sg requested in.
> Additionally, the code can be simplified much if it's just for the
> specific use case.
> 

ok. i will add some comments. and let the code be simplified.

> > > > +       return vchan_tx_prep(&c->vc, &d->vd, tx_flags);
> > > > +}
> > > > +
> > > > +static void mtk_dma_issue_pending(struct dma_chan *chan)
> > > > +{
> > > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > > +       struct virt_dma_desc *vd;
> > > > +       struct mtk_dmadev *mtkd;
> > > > +       unsigned long flags;
> > > > +
> > > > +       spin_lock_irqsave(&c->vc.lock, flags);
> > > > +       if (c->cfg.direction == DMA_DEV_TO_MEM) {
> > > > +               mtkd = to_mtk_dma_dev(chan->device);
> > >
> > > mtkd can be dropped as it seems no users
> > >
> 
> < ... >
> 
> > > > +static int mtk_dma_slave_config(struct dma_chan *chan,
> > > > +                               struct dma_slave_config *cfg)
> > > > +{
> > > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > > +       struct mtk_dmadev *mtkd = to_mtk_dma_dev(c->vc.chan.device);
> > > > +       int ret;
> > > > +
> > > > +       c->cfg = *cfg;
> > > > +
> > > > +       if (cfg->direction == DMA_DEV_TO_MEM) {
> > > > +               unsigned int rx_len = cfg->src_addr_width * 1024;
> > >
> > > it seems you should use cfg->src_port_window_size as the comments explains
> > >
> > > * @src_port_window_size: The length of the register area in words the data need
> > >  * to be accessed on the device side. It is only used for devices which is using
> > >  * an area instead of a single register to receive the data. Typically the DMA
> > >  * loops in this area in order to transfer the data.
> > >  * @dst_port_window_size: same as src_port_window_size but for the destination
> > >  * port.
> > >
> >
> > in 8250 UART native code, will set the parameter. if want to modify
> > this, i think that maybe at next kernel release, we can modify it. i
> > suggest that not modify it at this patch. because it relate of 8250 uart
> > code. thanks.
> >
> 
> You can fix it in the next version and a separate follow-up patch for
> the client driver.
> 
> > > > +
> > > > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->src_addr);
> > > > +               mtk_dma_chan_write(c, VFF_LEN, rx_len);
> > > > +               mtk_dma_chan_write(c, VFF_THRE, VFF_RX_THRE(rx_len));
> > > > +               mtk_dma_chan_write(c,
> > > > +                                  VFF_INT_EN, VFF_RX_INT_EN0_B
> > > > +                                  | VFF_RX_INT_EN1_B);
> > > > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> > > > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> > >
> > > I'd prefer to move those channel interrupt enablement to
> > > .device_alloc_chan_resources
> > > and related disablement to .device_free_chan_resources
> > >
> >
> > i think that, first need set the config to HW, and the enable the DMA.
> >
> 
> I've read through the client driver and the dmaengine, I probably know
> how interaction they work and find out there is something you seem
> completely make a wrong.
> 
> You can't do enable DMA with enabling VFF here. That causes a big
> problem, DMA would self decide to move data and not managed and issued
> by the dmaengine framework. For instance in DMA Tx path, because you
> enable the DMA and DMA  buffer (VFF) and UART Tx ring uses the same
> memory area,  DMA would self start to move data once data from
> userland go in Tx ring even without being issued by dmaengine.
> 
> Instead, you should ensure all descriptors are being batched by
> .device_prep_slave_sg and DMA does not start moving data until
> .device_issue_pending done and once descriptors are issued, DMA
> hardware or software have to do it as fast as possible.
> 

the VFF enable just enable the DMA function. DMA can't move data here.
Now, the code get length of the data in '.device_prep_slave_sg'.
And let DMA move data in '.device_issue_pending function'. in here, just
enable the function.

> > > > +
> > > > +               if (!c->requested) {
> > > > +                       c->requested = true;
> > > > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > > > +                                         mtk_dma_rx_interrupt,
> > > > +                                         IRQF_TRIGGER_NONE,
> > > > +                                         KBUILD_MODNAME, chan);
> > >
> > > ISR registration usually happens as the driver got probe, it can give
> > > the system more flexibility to manage such IRQ affinity on the fly.
> > >
> >
> > i will move the request irq to alloc channel.
> >
> 
> why don't let it done in driver probe?
> 
there are many uart ports, like UART[0-5]. in probe, just get the all
irq of ports. which port is using, who request irq. example, UART1 is
using. we just request irq of uart1. uart0, uart[2-5] don't need request
irq.

> > > > +                       if (ret < 0) {
> > > > +                               dev_err(chan->device->dev, "Can't request rx dma IRQ\n");
> > > > +                               return -EINVAL;
> > > > +                       }
> > > > +               }
> > > > +       } else if (cfg->direction == DMA_MEM_TO_DEV)    {
> > > > +               unsigned int tx_len = cfg->dst_addr_width * 1024;
> > >
> > > Ditto as above, it seems you should use cfg->dst_port_window_size
> > >
> > > > +
> > > > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->dst_addr);
> > > > +               mtk_dma_chan_write(c, VFF_LEN, tx_len);
> > > > +               mtk_dma_chan_write(c, VFF_THRE, VFF_TX_THRE(tx_len));
> > > > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> > > > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> > >
> > > ditto, I'd prefer to move those channel interrupt enablement to
> > > .device_alloc_chan_resources and related disablement to
> > > .device_free_chan_resources
> > >
> > > > +
> > > > +               if (!c->requested) {
> > > > +                       c->requested = true;
> > > > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > > > +                                         mtk_dma_tx_interrupt,
> > > > +                                         IRQF_TRIGGER_NONE,
> > > > +                                         KBUILD_MODNAME, chan);
> > >
> > > ditto, we can request ISR with devm_request_irq in the driver got
> > > probe and trim the c->request member
> > >
> > > > +                       if (ret < 0) {
> > > > +                               dev_err(chan->device->dev, "Can't request tx dma IRQ\n");
> > > > +                               return -EINVAL;
> > > > +                       }
> > > > +               }
> > > > +       }
> > > > +
> > > > +       if (mtkd->support_33bits)
> > > > +               mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_B);
> > > > +
> > > > +       if (mtk_dma_chan_read(c, VFF_EN) != VFF_EN_B) {
> > > > +               dev_err(chan->device->dev,
> > > > +                       "config dma dir[%d] fail\n", cfg->direction);
> > > > +               return -EINVAL;
> > > > +       }
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static int mtk_dma_terminate_all(struct dma_chan *chan)
> > > > +{
> > > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > > +       unsigned long flags;
> > > > +
> > > > +       spin_lock_irqsave(&c->vc.lock, flags);
> > > > +       list_del_init(&c->node);
> > > > +       mtk_dma_stop(c);
> > > > +       spin_unlock_irqrestore(&c->vc.lock, flags);
> > > > +
> > > > +       return 0;
> > > > +}
> > > > +
> > > > +static int mtk_dma_device_pause(struct dma_chan *chan)
> > > > +{
> > > > +       /* just for check caps pass */
> > > > +       return -EINVAL;
> > >
> > > always return error code seems not the client driver wants us to do.
> > >
> > > maybe if the hardware doesn't support pause, we can make a software
> > > pause, that waits until all active descriptors in hardware done, then
> > > disable interrupt and then stop handling the following vd in the
> > > vchan.
> > >
> > > > +}
> >
> > the code can't run. just for 8250 native code to check the function
> > pointer. in the future, if the function useful, we can realize. thanks.
> >
> 
> Always return an error code looks like it's a faked function just to
> pass the criteria check. It seems not a good idea.
> 

yes, the function is fake. i just review the 8250 uart framework. there
no check the return value of the function. so i can modify it to 'return
0'

> > > > +
> > > > +static int mtk_dma_device_resume(struct dma_chan *chan)
> > > > +{
> > > > +       /* just for check caps pass */
> > > > +       return -EINVAL;
> 
> < ... >
> 
> > > > +static struct platform_driver mtk_dma_driver = {
> > >
> > > mtk_dma is much general and all functions and structures in the driver
> > > should be all consistent.  I'd prefer to have all naming starts with
> > > mtk_uart_apdma.
> > >
> >
> > the function name and parameters' name, i will modify it. but before the
> > 8250_mtk.c and the Doc. are recorded. if modify file name and Kconfig,
> > will bring about the disorder. i suggest that after the patch is
> > recorded, modify this. thanks.
> >
> 
> We can do it in separate patches and in a logical order for the
> changes required across different subsystems.
> 
> > > > +       .probe  = mtk_apdma_probe,
> > >
> > > such  as
> > > mtk_uart_apdma_probe
> > >
> > > > +       .remove = mtk_apdma_remove,
> > >
> > > mtk_uart_apdma_remove
> > >
> > > > +       .driver = {
> > > > +               .name           = KBUILD_MODNAME,
> > > > +               .pm             = &mtk_dma_pm_ops,
> > >
> > > mtk_uart_apdma_pm_ops
> > >
> > > > +               .of_match_table = of_match_ptr(mtk_uart_dma_match),
> > >
> > > mtk_uart_apdma_match
> > >
> > > > +       },
> > > > +};
> > > > +
> > > > +module_platform_driver(mtk_dma_driver);
> > >
> > > mtk_uart_apdma_driver
> > >
> > > > +
> > > > +MODULE_DESCRIPTION("MediaTek UART APDMA Controller Driver");
> > > > +MODULE_AUTHOR("Long Cheng <long.cheng@mediatek.com>");
> > > > +MODULE_LICENSE("GPL v2");
> > > > +
> > > > diff --git a/drivers/dma/mediatek/Kconfig b/drivers/dma/mediatek/Kconfig
> > > > index 27bac0b..d399624 100644
> > > > --- a/drivers/dma/mediatek/Kconfig
> > > > +++ b/drivers/dma/mediatek/Kconfig
> > > > @@ -1,4 +1,15 @@
> > > >
> > > > +config DMA_MTK_UART
> > >
> > > MTK_UART_APDMA to align the other drivers
> > >
> > > > +       tristate "MediaTek SoCs APDMA support for UART"
> > > > +       depends on OF && SERIAL_8250_MT6577
> > > > +       select DMA_ENGINE
> > > > +       select DMA_VIRTUAL_CHANNELS
> > > > +       help
> > > > +         Support for the UART DMA engine found on MediaTek MTK SoCs.
> > > > +         when 8250 mtk uart is enabled, and if you want to using DMA,
> > >
> > > 8250 mtk uart should be changed to SERIAL_8250_MT6577 to be more intuitive
> > >
> > > > +         you can enable the config. the DMA engine just only be used
> > > > +         with MediaTek Socs.
> > >
> > > SoCs
> > >
> > > > +
> > > >  config MTK_HSDMA
> > > >         tristate "MediaTek High-Speed DMA controller support"
> > > >         depends on ARCH_MEDIATEK || COMPILE_TEST
> > > > diff --git a/drivers/dma/mediatek/Makefile b/drivers/dma/mediatek/Makefile
> > > > index 6e778f8..2f2efd9 100644
> > > > --- a/drivers/dma/mediatek/Makefile
> > > > +++ b/drivers/dma/mediatek/Makefile
> > > > @@ -1 +1,2 @@
> > > > +obj-$(CONFIG_DMA_MTK_UART) += 8250_mtk_dma.o
> > >
> > > obj-$(CONFIG_MTK_UART_APDMA) += mtk-uart-apdma.o
> > > to align the other dirvers
> > >
> > > >  obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o
> > > > --
> > > > 1.7.9.5
> > > >
> >
> >



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 1/2] dmaengine: 8250_mtk_dma: add Mediatek uart DMA support

[Sean Wang]

On Mon, Dec 17, 2018 at 12:40 AM Long Cheng <long.cheng@mediatek.com> wrote:
>
> On Fri, 2018-12-14 at 12:09 -0800, Sean Wang wrote:

< ... >

> > > > > +
> > > > > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->src_addr);
> > > > > +               mtk_dma_chan_write(c, VFF_LEN, rx_len);
> > > > > +               mtk_dma_chan_write(c, VFF_THRE, VFF_RX_THRE(rx_len));
> > > > > +               mtk_dma_chan_write(c,
> > > > > +                                  VFF_INT_EN, VFF_RX_INT_EN0_B
> > > > > +                                  | VFF_RX_INT_EN1_B);
> > > > > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> > > > > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> > > >
> > > > I'd prefer to move those channel interrupt enablement to
> > > > .device_alloc_chan_resources
> > > > and related disablement to .device_free_chan_resources
> > > >
> > >
> > > i think that, first need set the config to HW, and the enable the DMA.
> > >
> >
> > I've read through the client driver and the dmaengine, I probably know
> > how interaction they work and find out there is something you seem
> > completely make a wrong.
> >
> > You can't do enable DMA with enabling VFF here. That causes a big
> > problem, DMA would self decide to move data and not managed and issued
> > by the dmaengine framework. For instance in DMA Tx path, because you
> > enable the DMA and DMA  buffer (VFF) and UART Tx ring uses the same
> > memory area,  DMA would self start to move data once data from
> > userland go in Tx ring even without being issued by dmaengine.
> >
> > Instead, you should ensure all descriptors are being batched by
> > .device_prep_slave_sg and DMA does not start moving data until
> > .device_issue_pending done and once descriptors are issued, DMA
> > hardware or software have to do it as fast as possible.
> >
>
> the VFF enable just enable the DMA function. DMA can't move data here.
> Now, the code get length of the data in '.device_prep_slave_sg'.
> And let DMA move data in '.device_issue_pending function'. in here, just
> enable the function.
>

My all curiosity are all from the descriptor programmed in
.device_issue_pending in the other drivers at least includes
information such data length, target address, and hardware control
code, but in the driver only includes data length and even the target
address is set up at device_config, that seems unusual.

And, It does too for DMA_DEV_TO_MEM?  What I see is there is almost no
any code be programmed for kick off the hardware for the direction but
DMA still can move. That is another point I got confused.

> > > > > +
> > > > > +               if (!c->requested) {
> > > > > +                       c->requested = true;
> > > > > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > > > > +                                         mtk_dma_rx_interrupt,
> > > > > +                                         IRQF_TRIGGER_NONE,
> > > > > +                                         KBUILD_MODNAME, chan);
> > > >
> > > > ISR registration usually happens as the driver got probe, it can give
> > > > the system more flexibility to manage such IRQ affinity on the fly.
> > > >
> > >
> > > i will move the request irq to alloc channel.
> > >
> >
> > why don't let it done in driver probe?
> >
> there are many uart ports, like UART[0-5]. in probe, just get the all
> irq of ports. which port is using, who request irq. example, UART1 is
> using. we just request irq of uart1. uart0, uart[2-5] don't need request
> irq.
>
> > > > > +                       if (ret < 0) {
> > > > > +                               dev_err(chan->device->dev, "Can't request rx dma IRQ\n");
> > > > > +                               return -EINVAL;
> > > > > +                       }
> > > > > +               }
> > > > > +       } else if (cfg->direction == DMA_MEM_TO_DEV)    {
> > > > > +               unsigned int tx_len = cfg->dst_addr_width * 1024;
> > > >
> > > > Ditto as above, it seems you should use cfg->dst_port_window_size
> > > >
> > > > > +
> > > > > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->dst_addr);
> > > > > +               mtk_dma_chan_write(c, VFF_LEN, tx_len);
> > > > > +               mtk_dma_chan_write(c, VFF_THRE, VFF_TX_THRE(tx_len));
> > > > > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> > > > > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> > > >
> > > > ditto, I'd prefer to move those channel interrupt enablement to
> > > > .device_alloc_chan_resources and related disablement to
> > > > .device_free_chan_resources
> > > >
> > > > > +
> > > > > +               if (!c->requested) {
> > > > > +                       c->requested = true;
> > > > > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > > > > +                                         mtk_dma_tx_interrupt,
> > > > > +                                         IRQF_TRIGGER_NONE,
> > > > > +                                         KBUILD_MODNAME, chan);
> > > >
> > > > ditto, we can request ISR with devm_request_irq in the driver got
> > > > probe and trim the c->request member
> > > >
> > > > > +                       if (ret < 0) {
> > > > > +                               dev_err(chan->device->dev, "Can't request tx dma IRQ\n");
> > > > > +                               return -EINVAL;
> > > > > +                       }
> > > > > +               }
> > > > > +       }
> > > > > +
> > > > > +       if (mtkd->support_33bits)
> > > > > +               mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_B);
> > > > > +
> > > > > +       if (mtk_dma_chan_read(c, VFF_EN) != VFF_EN_B) {
> > > > > +               dev_err(chan->device->dev,
> > > > > +                       "config dma dir[%d] fail\n", cfg->direction);
> > > > > +               return -EINVAL;
> > > > > +       }
> > > > > +
> > > > > +       return 0;
> > > > > +}
> > > > > +
> > > > > +static int mtk_dma_terminate_all(struct dma_chan *chan)
> > > > > +{
> > > > > +       struct mtk_chan *c = to_mtk_dma_chan(chan);
> > > > > +       unsigned long flags;
> > > > > +
> > > > > +       spin_lock_irqsave(&c->vc.lock, flags);
> > > > > +       list_del_init(&c->node);
> > > > > +       mtk_dma_stop(c);
> > > > > +       spin_unlock_irqrestore(&c->vc.lock, flags);
> > > > > +
> > > > > +       return 0;
> > > > > +}
> > > > > +
> > > > > +static int mtk_dma_device_pause(struct dma_chan *chan)
> > > > > +{
> > > > > +       /* just for check caps pass */
> > > > > +       return -EINVAL;
> > > >
> > > > always return error code seems not the client driver wants us to do.
> > > >
> > > > maybe if the hardware doesn't support pause, we can make a software
> > > > pause, that waits until all active descriptors in hardware done, then
> > > > disable interrupt and then stop handling the following vd in the
> > > > vchan.
> > > >
> > > > > +}
> > >
> > > the code can't run. just for 8250 native code to check the function
> > > pointer. in the future, if the function useful, we can realize. thanks.
> > >
> >
> > Always return an error code looks like it's a faked function just to
> > pass the criteria check. It seems not a good idea.
> >
>
> yes, the function is fake. i just review the 8250 uart framework. there
> no check the return value of the function. so i can modify it to 'return
> 0'
>
> > > > > +
> > > > > +static int mtk_dma_device_resume(struct dma_chan *chan)
> > > > > +{
> > > > > +       /* just for check caps pass */
> > > > > +       return -EINVAL;
> >
> > < ... >
> >
> > > > > +static struct platform_driver mtk_dma_driver = {
> > > >
> > > > mtk_dma is much general and all functions and structures in the driver
> > > > should be all consistent.  I'd prefer to have all naming starts with
> > > > mtk_uart_apdma.
> > > >
> > >
> > > the function name and parameters' name, i will modify it. but before the
> > > 8250_mtk.c and the Doc. are recorded. if modify file name and Kconfig,
> > > will bring about the disorder. i suggest that after the patch is
> > > recorded, modify this. thanks.
> > >
> >
> > We can do it in separate patches and in a logical order for the
> > changes required across different subsystems.
> >
> > > > > +       .probe  = mtk_apdma_probe,
> > > >
> > > > such  as
> > > > mtk_uart_apdma_probe
> > > >
> > > > > +       .remove = mtk_apdma_remove,
> > > >
> > > > mtk_uart_apdma_remove
> > > >
> > > > > +       .driver = {
> > > > > +               .name           = KBUILD_MODNAME,
> > > > > +               .pm             = &mtk_dma_pm_ops,
> > > >
> > > > mtk_uart_apdma_pm_ops
> > > >
> > > > > +               .of_match_table = of_match_ptr(mtk_uart_dma_match),
> > > >
> > > > mtk_uart_apdma_match
> > > >
> > > > > +       },
> > > > > +};
> > > > > +
> > > > > +module_platform_driver(mtk_dma_driver);
> > > >
> > > > mtk_uart_apdma_driver
> > > >
> > > > > +
> > > > > +MODULE_DESCRIPTION("MediaTek UART APDMA Controller Driver");
> > > > > +MODULE_AUTHOR("Long Cheng <long.cheng@mediatek.com>");
> > > > > +MODULE_LICENSE("GPL v2");
> > > > > +
> > > > > diff --git a/drivers/dma/mediatek/Kconfig b/drivers/dma/mediatek/Kconfig
> > > > > index 27bac0b..d399624 100644
> > > > > --- a/drivers/dma/mediatek/Kconfig
> > > > > +++ b/drivers/dma/mediatek/Kconfig
> > > > > @@ -1,4 +1,15 @@
> > > > >
> > > > > +config DMA_MTK_UART
> > > >
> > > > MTK_UART_APDMA to align the other drivers
> > > >
> > > > > +       tristate "MediaTek SoCs APDMA support for UART"
> > > > > +       depends on OF && SERIAL_8250_MT6577
> > > > > +       select DMA_ENGINE
> > > > > +       select DMA_VIRTUAL_CHANNELS
> > > > > +       help
> > > > > +         Support for the UART DMA engine found on MediaTek MTK SoCs.
> > > > > +         when 8250 mtk uart is enabled, and if you want to using DMA,
> > > >
> > > > 8250 mtk uart should be changed to SERIAL_8250_MT6577 to be more intuitive
> > > >
> > > > > +         you can enable the config. the DMA engine just only be used
> > > > > +         with MediaTek Socs.
> > > >
> > > > SoCs
> > > >
> > > > > +
> > > > >  config MTK_HSDMA
> > > > >         tristate "MediaTek High-Speed DMA controller support"
> > > > >         depends on ARCH_MEDIATEK || COMPILE_TEST
> > > > > diff --git a/drivers/dma/mediatek/Makefile b/drivers/dma/mediatek/Makefile
> > > > > index 6e778f8..2f2efd9 100644
> > > > > --- a/drivers/dma/mediatek/Makefile
> > > > > +++ b/drivers/dma/mediatek/Makefile
> > > > > @@ -1 +1,2 @@
> > > > > +obj-$(CONFIG_DMA_MTK_UART) += 8250_mtk_dma.o
> > > >
> > > > obj-$(CONFIG_MTK_UART_APDMA) += mtk-uart-apdma.o
> > > > to align the other dirvers
> > > >
> > > > >  obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o
> > > > > --
> > > > > 1.7.9.5
> > > > >
> > >
> > >
>
>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 1/2] dmaengine: 8250_mtk_dma: add Mediatek uart DMA support

[Long Cheng]

On Mon, 2018-12-17 at 02:07 -0800, Sean Wang wrote:
> On Mon, Dec 17, 2018 at 12:40 AM Long Cheng <long.cheng@mediatek.com> wrote:
> >
> > On Fri, 2018-12-14 at 12:09 -0800, Sean Wang wrote:
> 
> < ... >
> 
> > > > > > +
> > > > > > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->src_addr);
> > > > > > +               mtk_dma_chan_write(c, VFF_LEN, rx_len);
> > > > > > +               mtk_dma_chan_write(c, VFF_THRE, VFF_RX_THRE(rx_len));
> > > > > > +               mtk_dma_chan_write(c,
> > > > > > +                                  VFF_INT_EN, VFF_RX_INT_EN0_B
> > > > > > +                                  | VFF_RX_INT_EN1_B);
> > > > > > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_RX_INT_FLAG_CLR_B);
> > > > > > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> > > > >
> > > > > I'd prefer to move those channel interrupt enablement to
> > > > > .device_alloc_chan_resources
> > > > > and related disablement to .device_free_chan_resources
> > > > >
> > > >
> > > > i think that, first need set the config to HW, and the enable the DMA.
> > > >
> > >
> > > I've read through the client driver and the dmaengine, I probably know
> > > how interaction they work and find out there is something you seem
> > > completely make a wrong.
> > >
> > > You can't do enable DMA with enabling VFF here. That causes a big
> > > problem, DMA would self decide to move data and not managed and issued
> > > by the dmaengine framework. For instance in DMA Tx path, because you
> > > enable the DMA and DMA  buffer (VFF) and UART Tx ring uses the same
> > > memory area,  DMA would self start to move data once data from
> > > userland go in Tx ring even without being issued by dmaengine.
> > >
> > > Instead, you should ensure all descriptors are being batched by
> > > .device_prep_slave_sg and DMA does not start moving data until
> > > .device_issue_pending done and once descriptors are issued, DMA
> > > hardware or software have to do it as fast as possible.
> > >
> >
> > the VFF enable just enable the DMA function. DMA can't move data here.
> > Now, the code get length of the data in '.device_prep_slave_sg'.
> > And let DMA move data in '.device_issue_pending function'. in here, just
> > enable the function.
> >
> 
> My all curiosity are all from the descriptor programmed in
> .device_issue_pending in the other drivers at least includes
> information such data length, target address, and hardware control
> code, but in the driver only includes data length and even the target
> address is set up at device_config, that seems unusual.
> 
> And, It does too for DMA_DEV_TO_MEM?  What I see is there is almost no
> any code be programmed for kick off the hardware for the direction but
> DMA still can move. That is another point I got confused.
> 

8250_dma in tty, mapping xmit buffer to DMA buffer. and the tx just use
the only one buffer. it's ring buffer. 8250_dma set the begin address
and length of the buffer by means of '.deivce_config' function. 
when TX happen, tty_write will write data to xmit buffer. in 8250_dma,
will set the address and length of the data by means of
'.device_prep_slave_sg'. but the address is in the xmit buffer rang. the
WPT(write pointer), RPT(read pointer) registers are recored the DMA data
transfer status, include the current location of transmission. and the
apdma is only for UART. So don't need recored the the address of data ,
target address in '.device_prep_slave_sg'.
in '.device_issue_pending', just using the data length from descriptor,
WPT ,  we can figure out what's data need to move. then update the WPT
and flush TX.

RX too. RX use other buffer in instead of XMIT buffer. when RX interrupt
coming, will update the RPT, and 8250_dma will get the length from vchan
complete. then 8250_dma can get the data.

> > > > > > +
> > > > > > +               if (!c->requested) {
> > > > > > +                       c->requested = true;
> > > > > > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > > > > > +                                         mtk_dma_rx_interrupt,
> > > > > > +                                         IRQF_TRIGGER_NONE,
> > > > > > +                                         KBUILD_MODNAME, chan);
> > > > >
> > > > > ISR registration usually happens as the driver got probe, it can give
> > > > > the system more flexibility to manage such IRQ affinity on the fly.
> > > > >
> > > >
> > > > i will move the request irq to alloc channel.
> > > >
> > >
> > > why don't let it done in driver probe?
> > >
> > there are many uart ports, like UART[0-5]. in probe, just get the all
> > irq of ports. which port is using, who request irq. example, UART1 is
> > using. we just request irq of uart1. uart0, uart[2-5] don't need request
> > irq.
> >
> > > > > > +                       if (ret < 0) {
> > > > > > +                               dev_err(chan->device->dev, "Can't request rx dma IRQ\n");
> > > > > > +                               return -EINVAL;
> > > > > > +                       }
> > > > > > +               }
> > > > > > +       } else if (cfg->direction == DMA_MEM_TO_DEV)    {
> > > > > > +               unsigned int tx_len = cfg->dst_addr_width * 1024;
> > > > >
> > > > > Ditto as above, it seems you should use cfg->dst_port_window_size
> > > > >
> > > > > > +
> > > > > > +               mtk_dma_chan_write(c, VFF_ADDR, cfg->dst_addr);
> > > > > > +               mtk_dma_chan_write(c, VFF_LEN, tx_len);
> > > > > > +               mtk_dma_chan_write(c, VFF_THRE, VFF_TX_THRE(tx_len));
> > > > > > +               mtk_dma_chan_write(c, VFF_INT_FLAG, VFF_TX_INT_FLAG_CLR_B);
> > > > > > +               mtk_dma_chan_write(c, VFF_EN, VFF_EN_B);
> > > > >
> > > > > ditto, I'd prefer to move those channel interrupt enablement to
> > > > > .device_alloc_chan_resources and related disablement to
> > > > > .device_free_chan_resources
> > > > >
> > > > > > +
> > > > > > +               if (!c->requested) {
> > > > > > +                       c->requested = true;
> > > > > > +                       ret = request_irq(mtkd->dma_irq[chan->chan_id],
> > > > > > +                                         mtk_dma_tx_interrupt,
> > > > > > +                                         IRQF_TRIGGER_NONE,
> > > > > > +                                         KBUILD_MODNAME, chan);
> > > > >
> > > > > ditto, we can request ISR with devm_request_irq in the driver got
> > > > > probe and trim the c->request member
> > > > >
> > > > > > +                       if (ret < 0) {
> > > > > > +                               dev_err(chan->device->dev, "Can't request tx dma IRQ\n");
> > > > > > +                               return -EINVAL;
> > > > > > +                       }
> > > > > > +               }
> > > > > > +       }
> > > > > > +
> > > > > > +       if (mtkd->support_33bits)
> > > > > > +               mtk_dma_chan_write(c, VFF_4G_SUPPORT, VFF_4G_SUPPORT_B);
> > > > > > +
> > > > > > +       if (mtk_dma_chan_read(c, VFF_EN) != VFF_EN_B) {
> > > > > > +               dev_err(chan->device->dev,
> > > > > > +                       "config dma dir[%d] fail\n", cfg->direction);
> > > > > > +               return -EINVAL;
> > > > > > +       }
> > > > > > +
> > > > > > +       return 0;
> > > > > > +}
> > > > > > +
< ... >


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 2/2] arm: dts: mt2712: add uart APDMA to device tree

[Long Cheng]

1. add uart APDMA controller device node
2. add uart 0/1/2/3/4/5 DMA function

Signed-off-by: Long Cheng <long.cheng@mediatek.com>
---
 arch/arm64/boot/dts/mediatek/mt2712e.dtsi |   50 +++++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
index 976d92a..a59728b 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -300,6 +300,9 @@
 		interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&baud_clk>, <&sys_clk>;
 		clock-names = "baud", "bus";
+		dmas = <&apdma 10
+			&apdma 11>;
+		dma-names = "tx", "rx";
 		status = "disabled";
 	};
 
@@ -378,6 +381,38 @@
 		status = "disabled";
 	};
 
+	apdma: dma-controller@11000400 {
+		compatible = "mediatek,mt2712-uart-dma",
+			     "mediatek,mt6577-uart-dma";
+		reg = <0 0x11000400 0 0x80>,
+		      <0 0x11000480 0 0x80>,
+		      <0 0x11000500 0 0x80>,
+		      <0 0x11000580 0 0x80>,
+		      <0 0x11000600 0 0x80>,
+		      <0 0x11000680 0 0x80>,
+		      <0 0x11000700 0 0x80>,
+		      <0 0x11000780 0 0x80>,
+		      <0 0x11000800 0 0x80>,
+		      <0 0x11000880 0 0x80>,
+		      <0 0x11000900 0 0x80>,
+		      <0 0x11000980 0 0x80>;
+		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 105 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 106 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 107 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 108 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 109 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 111 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 112 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_AP_DMA>;
+		clock-names = "apdma";
+		#dma-cells = <1>;
+	};
+
 	uart0: serial@11002000 {
 		compatible = "mediatek,mt2712-uart",
 			     "mediatek,mt6577-uart";
@@ -385,6 +420,9 @@
 		interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&baud_clk>, <&sys_clk>;
 		clock-names = "baud", "bus";
+		dmas = <&apdma 0
+			&apdma 1>;
+		dma-names = "tx", "rx";
 		status = "disabled";
 	};
 
@@ -395,6 +433,9 @@
 		interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&baud_clk>, <&sys_clk>;
 		clock-names = "baud", "bus";
+		dmas = <&apdma 2
+			&apdma 3>;
+		dma-names = "tx", "rx";
 		status = "disabled";
 	};
 
@@ -405,6 +446,9 @@
 		interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&baud_clk>, <&sys_clk>;
 		clock-names = "baud", "bus";
+		dmas = <&apdma 4
+			&apdma 5>;
+		dma-names = "tx", "rx";
 		status = "disabled";
 	};
 
@@ -415,6 +459,9 @@
 		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&baud_clk>, <&sys_clk>;
 		clock-names = "baud", "bus";
+		dmas = <&apdma 6
+			&apdma 7>;
+		dma-names = "tx", "rx";
 		status = "disabled";
 	};
 
@@ -629,6 +676,9 @@
 		interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&baud_clk>, <&sys_clk>;
 		clock-names = "baud", "bus";
+		dmas = <&apdma 8
+			&apdma 9>;
+		dma-names = "tx", "rx";
 		status = "disabled";
 	};
 
-- 
1.7.9.5


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 2/2] arm: dts: mt2712: add uart APDMA to device tree

[Yingjoe Chen]

On Tue, 2018-12-11 at 13:37 +0800, Long Cheng wrote:
> 1. add uart APDMA controller device node
> 2. add uart 0/1/2/3/4/5 DMA function
> 
> Signed-off-by: Long Cheng <long.cheng@mediatek.com>
> ---
>  arch/arm64/boot/dts/mediatek/mt2712e.dtsi |   50 +++++++++++++++++++++++++++++
>  1 file changed, 50 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> index 976d92a..a59728b 100644
> --- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> @@ -300,6 +300,9 @@
>  		interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
>  		clocks = <&baud_clk>, <&sys_clk>;
>  		clock-names = "baud", "bus";
> +		dmas = <&apdma 10
> +			&apdma 11>;
> +		dma-names = "tx", "rx";
>  		status = "disabled";
>  	};
>  
> @@ -378,6 +381,38 @@
>  		status = "disabled";
>  	};
>  
> +	apdma: dma-controller@11000400 {
> +		compatible = "mediatek,mt2712-uart-dma",
> +			     "mediatek,mt6577-uart-dma";

Sorting, please make sure this is before 

        auxadc: adc@11001000 {


> +		reg = <0 0x11000400 0 0x80>,
> +		      <0 0x11000480 0 0x80>,
> +		      <0 0x11000500 0 0x80>,
> +		      <0 0x11000580 0 0x80>,
> +		      <0 0x11000600 0 0x80>,
> +		      <0 0x11000680 0 0x80>,
> +		      <0 0x11000700 0 0x80>,
> +		      <0 0x11000780 0 0x80>,
> +		      <0 0x11000800 0 0x80>,
> +		      <0 0x11000880 0 0x80>,
> +		      <0 0x11000900 0 0x80>,
> +		      <0 0x11000980 0 0x80>;
> +		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 105 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 106 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 107 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 108 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 109 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 111 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 112 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>,
> +			     <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>;
> +		clocks = <&pericfg CLK_PERI_AP_DMA>;
> +		clock-names = "apdma";
> +		#dma-cells = <1>;
> +	};
> +
>  	uart0: serial@11002000 {
>  		compatible = "mediatek,mt2712-uart",
>  			     "mediatek,mt6577-uart";
> @@ -385,6 +420,9 @@


...deleted


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel