From mboxrd@z Thu Jan  1 00:00:00 1970
From: laurent.pinchart@ideasonboard.com (Laurent Pinchart)
Date: Wed, 05 Feb 2014 11:32:45 +0100
Subject: [Linux-kernel] [PATCH 2/3] ARM: shmobile: r8a7790: specify
 multiple parents for cpg_clks
In-Reply-To: <52F20133.6080107@codethink.co.uk>
References: <1391537858-28593-1-git-send-email-william.towle@codethink.co.uk>
 <1391537858-28593-3-git-send-email-william.towle@codethink.co.uk>
 <52F20133.6080107@codethink.co.uk>
Message-ID: <1565445.R9bPDKl3Py@avalon>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Hi Ben,

On Wednesday 05 February 2014 09:15:31 Ben Dooks wrote:
> On 04/02/14 18:17, William Towle wrote:
> > The current drivers/clk/shmobile/clk-rcar-gen2.c uses the
> > extal_clk reference for the parent of all the clocks that
> > it registers. However the lb, qspi, sdh, sd0 and sd1 clocks
> > are all parented to either pll1 or pll1_div2 which means
> > that the clock rates are incorrect.
> > 
> > This is part of the fix that corrects the SDHI0 clock
> > 
> > rate error where it reports 1MHz instead of 97.5:
> >      sh_mobile_sdhi ee100000.sd: mmc0 base at 0xee100000 clock rate 1 MHz
> > 
> > Notes:
> > - May require cross-merge with clk-rcar-gen2.c fix
> > - Also not clear which clock "z" is to fix it.
> 
> Laurent, if you could give us an idea of how to fix this then
> it would be helpful to get this patch fully fixed.

I've already sent a patch that fixes this issue.

"clk: shmobile: rcar-gen2: Fix clock parent all non-PLL clocks"

(http://www.spinics.net/lists/linux-sh/msg27275.html)

I've just pinged Mike to ask him to pick it up for v3.14.

> > [ben.dooks at codethink.co.uk: updated patch description]
> > Signed-off-by: William Towle <william.towle@codethink.co.uk>
> > Reviewed-by: Ben Dooks <ben.dooks@codethink.co.uk>
> > ---
> > 
> >   arch/arm/boot/dts/r8a7790.dtsi |    8 +++++++-
> >   1 file changed, 7 insertions(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm/boot/dts/r8a7790.dtsi
> > b/arch/arm/boot/dts/r8a7790.dtsi index ff55c6e..242e6e2 100644
> > --- a/arch/arm/boot/dts/r8a7790.dtsi
> > +++ b/arch/arm/boot/dts/r8a7790.dtsi
> > @@ -446,7 +446,13 @@
> > 
> >   			compatible = "renesas,r8a7790-cpg-clocks",
> >   			
> >   				     "renesas,rcar-gen2-cpg-clocks";
> >   			
> >   			reg = <0 0xe6150000 0 0x1000>;
> > 
> > -			clocks = <&extal_clk>;
> > +			clocks = <&extal_clk>, <&extal_clk>, <&extal_clk>, 
<&extal_clk>,
> > +				<&cpg_clocks R8A7790_CLK_PLL1>,
> > +				<&pll1_div2_clk>,
> > +				<&cpg_clocks R8A7790_CLK_PLL1>,
> > +				<&cpg_clocks R8A7790_CLK_PLL1>,
> > +				<&cpg_clocks R8A7790_CLK_PLL1>
> 
> Should we add a pll1_clk node, or leave this as is?
> 
> > +				/* not known for "z" ...,<> */;
> > 
> >   			#clock-cells = <1>;
> >   			clock-output-names = "main", "pll0", "pll1", "pll3",
> >   			
> >   					     "lb", "qspi", "sdh", "sd0", "sd1",

-- 
Regards,

Laurent Pinchart