* [PATCH v5 1/7] net-next: stmmac: dwmac-mediatek: add platform level clocks management
2021-12-07 1:54 [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Biao Huang
@ 2021-12-07 1:54 ` Biao Huang
2021-12-07 1:55 ` [PATCH v5 2/7] net-next: stmmac: dwmac-mediatek: Reuse more common features Biao Huang
` (6 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Biao Huang @ 2021-12-07 1:54 UTC (permalink / raw)
To: davem, Jakub Kicinski, Rob Herring
Cc: Matthias Brugger, Giuseppe Cavallaro, Alexandre Torgue,
Jose Abreu, Maxime Coquelin, Biao Huang, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
This patch implements clks_config callback for dwmac-mediatek platform,
which could support platform level clocks management.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
---
.../ethernet/stmicro/stmmac/dwmac-mediatek.c | 25 +++++++++++++------
1 file changed, 18 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
index 58c0feaa8131..0ff57c268dca 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
@@ -9,7 +9,6 @@
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/of_net.h>
-#include <linux/pm_runtime.h>
#include <linux/regmap.h>
#include <linux/stmmac.h>
@@ -359,9 +358,6 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
return ret;
}
- pm_runtime_enable(&pdev->dev);
- pm_runtime_get_sync(&pdev->dev);
-
return 0;
}
@@ -370,11 +366,25 @@ static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv)
struct mediatek_dwmac_plat_data *plat = priv;
clk_bulk_disable_unprepare(plat->num_clks_to_config, plat->clks);
-
- pm_runtime_put_sync(&pdev->dev);
- pm_runtime_disable(&pdev->dev);
}
+static int mediatek_dwmac_clks_config(void *priv, bool enabled)
+{
+ struct mediatek_dwmac_plat_data *plat = priv;
+ int ret = 0;
+
+ if (enabled) {
+ ret = clk_bulk_prepare_enable(plat->num_clks_to_config, plat->clks);
+ if (ret) {
+ dev_err(plat->dev, "failed to enable clks, err = %d\n", ret);
+ return ret;
+ }
+ } else {
+ clk_bulk_disable_unprepare(plat->num_clks_to_config, plat->clks);
+ }
+
+ return ret;
+}
static int mediatek_dwmac_probe(struct platform_device *pdev)
{
struct mediatek_dwmac_plat_data *priv_plat;
@@ -420,6 +430,7 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
plat_dat->bsp_priv = priv_plat;
plat_dat->init = mediatek_dwmac_init;
plat_dat->exit = mediatek_dwmac_exit;
+ plat_dat->clks_config = mediatek_dwmac_clks_config;
mediatek_dwmac_init(pdev, priv_plat);
ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v5 2/7] net-next: stmmac: dwmac-mediatek: Reuse more common features
2021-12-07 1:54 [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Biao Huang
2021-12-07 1:54 ` [PATCH v5 1/7] net-next: stmmac: dwmac-mediatek: add platform level clocks management Biao Huang
@ 2021-12-07 1:55 ` Biao Huang
2021-12-07 1:55 ` [PATCH v5 3/7] arm64: dts: mt2712: update ethernet device node Biao Huang
` (5 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Biao Huang @ 2021-12-07 1:55 UTC (permalink / raw)
To: davem, Jakub Kicinski, Rob Herring
Cc: Matthias Brugger, Giuseppe Cavallaro, Alexandre Torgue,
Jose Abreu, Maxime Coquelin, Biao Huang, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
This patch makes dwmac-mediatek reuse more features
supported by stmmac_platform.c.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
.../ethernet/stmicro/stmmac/dwmac-mediatek.c | 32 +++++++++----------
1 file changed, 15 insertions(+), 17 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
index 0ff57c268dca..8747aa4403e8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
@@ -334,22 +334,20 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
const struct mediatek_dwmac_variant *variant = plat->variant;
int ret;
- ret = dma_set_mask_and_coherent(plat->dev, DMA_BIT_MASK(variant->dma_bit_mask));
- if (ret) {
- dev_err(plat->dev, "No suitable DMA available, err = %d\n", ret);
- return ret;
- }
-
- ret = variant->dwmac_set_phy_interface(plat);
- if (ret) {
- dev_err(plat->dev, "failed to set phy interface, err = %d\n", ret);
- return ret;
+ if (variant->dwmac_set_phy_interface) {
+ ret = variant->dwmac_set_phy_interface(plat);
+ if (ret) {
+ dev_err(plat->dev, "failed to set phy interface, err = %d\n", ret);
+ return ret;
+ }
}
- ret = variant->dwmac_set_delay(plat);
- if (ret) {
- dev_err(plat->dev, "failed to set delay value, err = %d\n", ret);
- return ret;
+ if (variant->dwmac_set_delay) {
+ ret = variant->dwmac_set_delay(plat);
+ if (ret) {
+ dev_err(plat->dev, "failed to set delay value, err = %d\n", ret);
+ return ret;
+ }
}
ret = clk_bulk_prepare_enable(plat->num_clks_to_config, plat->clks);
@@ -422,15 +420,15 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
return PTR_ERR(plat_dat);
plat_dat->interface = priv_plat->phy_mode;
- plat_dat->has_gmac4 = 1;
- plat_dat->has_gmac = 0;
- plat_dat->pmt = 0;
+ plat_dat->use_phy_wol = 1;
plat_dat->riwt_off = 1;
plat_dat->maxmtu = ETH_DATA_LEN;
+ plat_dat->addr64 = priv_plat->variant->dma_bit_mask;
plat_dat->bsp_priv = priv_plat;
plat_dat->init = mediatek_dwmac_init;
plat_dat->exit = mediatek_dwmac_exit;
plat_dat->clks_config = mediatek_dwmac_clks_config;
+
mediatek_dwmac_init(pdev, priv_plat);
ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v5 3/7] arm64: dts: mt2712: update ethernet device node
2021-12-07 1:54 [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Biao Huang
2021-12-07 1:54 ` [PATCH v5 1/7] net-next: stmmac: dwmac-mediatek: add platform level clocks management Biao Huang
2021-12-07 1:55 ` [PATCH v5 2/7] net-next: stmmac: dwmac-mediatek: Reuse more common features Biao Huang
@ 2021-12-07 1:55 ` Biao Huang
2021-12-07 1:55 ` [PATCH v5 4/7] net-next: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema Biao Huang
` (4 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Biao Huang @ 2021-12-07 1:55 UTC (permalink / raw)
To: davem, Jakub Kicinski, Rob Herring
Cc: Matthias Brugger, Giuseppe Cavallaro, Alexandre Torgue,
Jose Abreu, Maxime Coquelin, Biao Huang, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
Since there are some changes in ethernet driver,
update ethernet device node in dts to accommodate to it.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
---
arch/arm64/boot/dts/mediatek/mt2712-evb.dts | 1 +
arch/arm64/boot/dts/mediatek/mt2712e.dtsi | 14 +++++++++-----
2 files changed, 10 insertions(+), 5 deletions(-)
diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
index 7d369fdd3117..11aa135aa0f3 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
@@ -110,6 +110,7 @@ ð {
phy-handle = <ðernet_phy0>;
mediatek,tx-delay-ps = <1530>;
snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
+ snps,reset-delays-us = <0 10000 10000>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <ð_default>;
pinctrl-1 = <ð_sleep>;
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
index a9cca9c146fd..9e850e04fffb 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -726,7 +726,7 @@ queue2 {
};
eth: ethernet@1101c000 {
- compatible = "mediatek,mt2712-gmac";
+ compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a";
reg = <0 0x1101c000 0 0x1300>;
interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
interrupt-names = "macirq";
@@ -734,15 +734,19 @@ eth: ethernet@1101c000 {
clock-names = "axi",
"apb",
"mac_main",
- "ptp_ref";
+ "ptp_ref",
+ "rmii_internal";
clocks = <&pericfg CLK_PERI_GMAC>,
<&pericfg CLK_PERI_GMAC_PCLK>,
<&topckgen CLK_TOP_ETHER_125M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_SEL>;
+ <&topckgen CLK_TOP_ETHER_50M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_SEL>;
+ <&topckgen CLK_TOP_ETHER_50M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
- <&topckgen CLK_TOP_APLL1_D3>;
+ <&topckgen CLK_TOP_APLL1_D3>,
+ <&topckgen CLK_TOP_ETHERPLL_50M>;
power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
mediatek,pericfg = <&pericfg>;
snps,axi-config = <&stmmac_axi_setup>;
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v5 4/7] net-next: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema
2021-12-07 1:54 [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Biao Huang
` (2 preceding siblings ...)
2021-12-07 1:55 ` [PATCH v5 3/7] arm64: dts: mt2712: update ethernet device node Biao Huang
@ 2021-12-07 1:55 ` Biao Huang
2021-12-07 14:58 ` Rob Herring
2021-12-07 1:55 ` [PATCH v5 5/7] net-next: stmmac: dwmac-mediatek: add support for mt8195 Biao Huang
` (3 subsequent siblings)
7 siblings, 1 reply; 12+ messages in thread
From: Biao Huang @ 2021-12-07 1:55 UTC (permalink / raw)
To: davem, Jakub Kicinski, Rob Herring
Cc: Matthias Brugger, Giuseppe Cavallaro, Alexandre Torgue,
Jose Abreu, Maxime Coquelin, Biao Huang, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
Convert mediatek-dwmac to DT schema, and delete old mediatek-dwmac.txt.
And there are some changes in .yaml than .txt, others almost keep the same:
1. compatible "const: snps,dwmac-4.20".
2. delete "snps,reset-active-low;" in example, since driver remove this
property long ago.
3. add "snps,reset-delay-us = <0 10000 10000>" in example.
4. the example is for rgmii interface, keep related properties only.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
---
.../bindings/net/mediatek-dwmac.txt | 91 ----------
.../bindings/net/mediatek-dwmac.yaml | 156 ++++++++++++++++++
2 files changed, 156 insertions(+), 91 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt
create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt
deleted file mode 100644
index afbcaebf062e..000000000000
--- a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt
+++ /dev/null
@@ -1,91 +0,0 @@
-MediaTek DWMAC glue layer controller
-
-This file documents platform glue layer for stmmac.
-Please see stmmac.txt for the other unchanged properties.
-
-The device node has following properties.
-
-Required properties:
-- compatible: Should be "mediatek,mt2712-gmac" for MT2712 SoC
-- reg: Address and length of the register set for the device
-- interrupts: Should contain the MAC interrupts
-- interrupt-names: Should contain a list of interrupt names corresponding to
- the interrupts in the interrupts property, if available.
- Should be "macirq" for the main MAC IRQ
-- clocks: Must contain a phandle for each entry in clock-names.
-- clock-names: The name of the clock listed in the clocks property. These are
- "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC.
-- mac-address: See ethernet.txt in the same directory
-- phy-mode: See ethernet.txt in the same directory
-- mediatek,pericfg: A phandle to the syscon node that control ethernet
- interface and timing delay.
-
-Optional properties:
-- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0.
- It should be defined for RGMII/MII interface.
- It should be defined for RMII interface when the reference clock is from MT2712 SoC.
-- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0.
- It should be defined for RGMII/MII interface.
- It should be defined for RMII interface.
-Both delay properties need to be a multiple of 170 for RGMII interface,
-or will round down. Range 0~31*170.
-Both delay properties need to be a multiple of 550 for MII/RMII interface,
-or will round down. Range 0~31*550.
-
-- mediatek,rmii-rxc: boolean property, if present indicates that the RMII
- reference clock, which is from external PHYs, is connected to RXC pin
- on MT2712 SoC.
- Otherwise, is connected to TXC pin.
-- mediatek,rmii-clk-from-mac: boolean property, if present indicates that
- MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only.
-- mediatek,txc-inverse: boolean property, if present indicates that
- 1. tx clock will be inversed in MII/RGMII case,
- 2. tx clock inside MAC will be inversed relative to reference clock
- which is from external PHYs in RMII case, and it rarely happen.
- 3. the reference clock, which outputs to TXC pin will be inversed in RMII case
- when the reference clock is from MT2712 SoC.
-- mediatek,rxc-inverse: boolean property, if present indicates that
- 1. rx clock will be inversed in MII/RGMII case.
- 2. reference clock will be inversed when arrived at MAC in RMII case, when
- the reference clock is from external PHYs.
- 3. the inside clock, which be sent to MAC, will be inversed in RMII case when
- the reference clock is from MT2712 SoC.
-- assigned-clocks: mac_main and ptp_ref clocks
-- assigned-clock-parents: parent clocks of the assigned clocks
-
-Example:
- eth: ethernet@1101c000 {
- compatible = "mediatek,mt2712-gmac";
- reg = <0 0x1101c000 0 0x1300>;
- interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
- interrupt-names = "macirq";
- phy-mode ="rgmii-rxid";
- mac-address = [00 55 7b b5 7d f7];
- clock-names = "axi",
- "apb",
- "mac_main",
- "ptp_ref",
- "rmii_internal";
- clocks = <&pericfg CLK_PERI_GMAC>,
- <&pericfg CLK_PERI_GMAC_PCLK>,
- <&topckgen CLK_TOP_ETHER_125M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
- assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_SEL>,
- <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
- assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
- <&topckgen CLK_TOP_APLL1_D3>,
- <&topckgen CLK_TOP_ETHERPLL_50M>;
- power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
- mediatek,pericfg = <&pericfg>;
- mediatek,tx-delay-ps = <1530>;
- mediatek,rx-delay-ps = <1530>;
- mediatek,rmii-rxc;
- mediatek,txc-inverse;
- mediatek,rxc-inverse;
- snps,txpbl = <1>;
- snps,rxpbl = <1>;
- snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
- snps,reset-active-low;
- };
diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
new file mode 100644
index 000000000000..9207266a6e69
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
@@ -0,0 +1,156 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mediatek-dwmac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek DWMAC glue layer controller
+
+maintainers:
+ - Biao Huang <biao.huang@mediatek.com>
+
+description:
+ This file documents platform glue layer for stmmac.
+
+# We need a select here so we don't match all nodes with 'snps,dwmac'
+select:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - mediatek,mt2712-gmac
+ required:
+ - compatible
+
+allOf:
+ - $ref: "snps,dwmac.yaml#"
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - mediatek,mt2712-gmac
+ - const: snps,dwmac-4.20a
+
+ clocks:
+ items:
+ - description: AXI clock
+ - description: APB clock
+ - description: MAC Main clock
+ - description: PTP clock
+ - description: RMII reference clock provided by MAC
+
+ clock-names:
+ items:
+ - const: axi
+ - const: apb
+ - const: mac_main
+ - const: ptp_ref
+ - const: rmii_internal
+
+ mediatek,pericfg:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ The phandle to the syscon node that control ethernet
+ interface and timing delay.
+
+ mediatek,tx-delay-ps:
+ description:
+ The internal TX clock delay (provided by this driver) in nanoseconds.
+ For MT2712 RGMII interface, Allowed value need to be a multiple of 170,
+ or will round down. Range 0~31*170.
+ For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
+ or will round down. Range 0~31*550.
+
+ mediatek,rx-delay-ps:
+ description:
+ The internal RX clock delay (provided by this driver) in nanoseconds.
+ For MT2712 RGMII interface, Allowed value need to be a multiple of 170,
+ or will round down. Range 0~31*170.
+ For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
+ or will round down. Range 0~31*550.
+
+ mediatek,rmii-rxc:
+ type: boolean
+ description:
+ If present, indicates that the RMII reference clock, which is from external
+ PHYs, is connected to RXC pin. Otherwise, is connected to TXC pin.
+
+ mediatek,rmii-clk-from-mac:
+ type: boolean
+ description:
+ If present, indicates that MAC provides the RMII reference clock, which
+ outputs to TXC pin only.
+
+ mediatek,txc-inverse:
+ type: boolean
+ description:
+ If present, indicates that
+ 1. tx clock will be inversed in MII/RGMII case,
+ 2. tx clock inside MAC will be inversed relative to reference clock
+ which is from external PHYs in RMII case, and it rarely happen.
+ 3. the reference clock, which outputs to TXC pin will be inversed in RMII case
+ when the reference clock is from MAC.
+
+ mediatek,rxc-inverse:
+ type: boolean
+ description:
+ If present, indicates that
+ 1. rx clock will be inversed in MII/RGMII case.
+ 2. reference clock will be inversed when arrived at MAC in RMII case, when
+ the reference clock is from external PHYs.
+ 3. the inside clock, which be sent to MAC, will be inversed in RMII case when
+ the reference clock is from MAC.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-names
+ - clocks
+ - clock-names
+ - phy-mode
+ - mediatek,pericfg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt2712-clk.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/power/mt2712-power.h>
+
+ eth: ethernet@1101c000 {
+ compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a";
+ reg = <0x1101c000 0x1300>;
+ interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "macirq";
+ phy-mode ="rgmii-rxid";
+ mac-address = [00 55 7b b5 7d f7];
+ clock-names = "axi",
+ "apb",
+ "mac_main",
+ "ptp_ref",
+ "rmii_internal";
+ clocks = <&pericfg CLK_PERI_GMAC>,
+ <&pericfg CLK_PERI_GMAC_PCLK>,
+ <&topckgen CLK_TOP_ETHER_125M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
+ assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_SEL>,
+ <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
+ <&topckgen CLK_TOP_APLL1_D3>,
+ <&topckgen CLK_TOP_ETHERPLL_50M>;
+ power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
+ mediatek,pericfg = <&pericfg>;
+ mediatek,tx-delay-ps = <1530>;
+ snps,txpbl = <1>;
+ snps,rxpbl = <1>;
+ snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
+ snps,reset-delays-us = <0 10000 10000>;
+ };
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v5 4/7] net-next: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema
2021-12-07 1:55 ` [PATCH v5 4/7] net-next: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema Biao Huang
@ 2021-12-07 14:58 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2021-12-07 14:58 UTC (permalink / raw)
To: Biao Huang
Cc: Rob Herring, linux-stm32, davem, netdev, dkirjanov, devicetree,
linux-kernel, srv_heupstream, linux-mediatek, Jakub Kicinski,
linux-arm-kernel, Matthias Brugger, Giuseppe Cavallaro,
angelogioacchino.delregno, Maxime Coquelin, Jose Abreu,
Alexandre Torgue, macpaul.lin
On Tue, 07 Dec 2021 09:55:02 +0800, Biao Huang wrote:
> Convert mediatek-dwmac to DT schema, and delete old mediatek-dwmac.txt.
> And there are some changes in .yaml than .txt, others almost keep the same:
> 1. compatible "const: snps,dwmac-4.20".
> 2. delete "snps,reset-active-low;" in example, since driver remove this
> property long ago.
> 3. add "snps,reset-delay-us = <0 10000 10000>" in example.
> 4. the example is for rgmii interface, keep related properties only.
>
> Signed-off-by: Biao Huang <biao.huang@mediatek.com>
> ---
> .../bindings/net/mediatek-dwmac.txt | 91 ----------
> .../bindings/net/mediatek-dwmac.yaml | 156 ++++++++++++++++++
> 2 files changed, 156 insertions(+), 91 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.txt
> create mode 100644 Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
>
Running 'make dtbs_check' with the schema in this patch gives the
following warnings. Consider if they are expected or the schema is
incorrect. These may not be new warnings.
Note that it is not yet a requirement to have 0 warnings for dtbs_check.
This will change in the future.
Full log is available here: https://patchwork.ozlabs.org/patch/1564459
ethernet@1101c000: clock-names: ['axi', 'apb', 'mac_main', 'ptp_ref'] is too short
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: clocks: [[27, 34], [27, 37], [6, 154], [6, 155]] is too short
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: compatible: ['mediatek,mt2712-gmac'] does not contain items matching the given schema
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: compatible: 'oneOf' conditional failed, one must be fixed:
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
ethernet@1101c000: Unevaluated properties are not allowed ('compatible', 'reg', 'interrupts', 'interrupt-names', 'mac-address', 'clock-names', 'clocks', 'power-domains', 'snps,axi-config', 'snps,mtl-rx-config', 'snps,mtl-tx-config', 'snps,txpbl', 'snps,rxpbl', 'clk_csr', 'phy-mode', 'phy-handle', 'snps,reset-gpio', 'mdio' were unexpected)
arch/arm64/boot/dts/mediatek/mt2712-evb.dt.yaml
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v5 5/7] net-next: stmmac: dwmac-mediatek: add support for mt8195
2021-12-07 1:54 [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Biao Huang
` (3 preceding siblings ...)
2021-12-07 1:55 ` [PATCH v5 4/7] net-next: dt-bindings: dwmac: Convert mediatek-dwmac to DT schema Biao Huang
@ 2021-12-07 1:55 ` Biao Huang
2021-12-07 1:55 ` [PATCH v5 6/7] arm64: dts: mt8195: add ethernet device node Biao Huang
` (2 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Biao Huang @ 2021-12-07 1:55 UTC (permalink / raw)
To: davem, Jakub Kicinski, Rob Herring
Cc: Matthias Brugger, Giuseppe Cavallaro, Alexandre Torgue,
Jose Abreu, Maxime Coquelin, Biao Huang, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
Add Ethernet support for MediaTek SoCs from the mt8195 family.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
.../ethernet/stmicro/stmmac/dwmac-mediatek.c | 253 +++++++++++++++++-
1 file changed, 252 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
index 8747aa4403e8..ce11c0d01014 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
@@ -39,6 +39,33 @@
#define ETH_FINE_DLY_GTXC BIT(1)
#define ETH_FINE_DLY_RXC BIT(0)
+/* Peri Configuration register for mt8195 */
+#define MT8195_PERI_ETH_CTRL0 0xFD0
+#define MT8195_RMII_CLK_SRC_INTERNAL BIT(28)
+#define MT8195_RMII_CLK_SRC_RXC BIT(27)
+#define MT8195_ETH_INTF_SEL GENMASK(26, 24)
+#define MT8195_RGMII_TXC_PHASE_CTRL BIT(22)
+#define MT8195_EXT_PHY_MODE BIT(21)
+#define MT8195_DLY_GTXC_INV BIT(12)
+#define MT8195_DLY_GTXC_ENABLE BIT(5)
+#define MT8195_DLY_GTXC_STAGES GENMASK(4, 0)
+
+#define MT8195_PERI_ETH_CTRL1 0xFD4
+#define MT8195_DLY_RXC_INV BIT(25)
+#define MT8195_DLY_RXC_ENABLE BIT(18)
+#define MT8195_DLY_RXC_STAGES GENMASK(17, 13)
+#define MT8195_DLY_TXC_INV BIT(12)
+#define MT8195_DLY_TXC_ENABLE BIT(5)
+#define MT8195_DLY_TXC_STAGES GENMASK(4, 0)
+
+#define MT8195_PERI_ETH_CTRL2 0xFD8
+#define MT8195_DLY_RMII_RXC_INV BIT(25)
+#define MT8195_DLY_RMII_RXC_ENABLE BIT(18)
+#define MT8195_DLY_RMII_RXC_STAGES GENMASK(17, 13)
+#define MT8195_DLY_RMII_TXC_INV BIT(12)
+#define MT8195_DLY_RMII_TXC_ENABLE BIT(5)
+#define MT8195_DLY_RMII_TXC_STAGES GENMASK(4, 0)
+
struct mac_delay_struct {
u32 tx_delay;
u32 rx_delay;
@@ -57,11 +84,13 @@ struct mediatek_dwmac_plat_data {
int num_clks_to_config;
bool rmii_clk_from_mac;
bool rmii_rxc;
+ bool mac_wol;
};
struct mediatek_dwmac_variant {
int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data *plat);
int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat);
+ void (*dwmac_fix_mac_speed)(void *priv, unsigned int speed);
/* clock ids to be requested */
const char * const *clk_list;
@@ -77,6 +106,10 @@ static const char * const mt2712_dwmac_clk_l[] = {
"axi", "apb", "mac_main", "ptp_ref", "rmii_internal"
};
+static const char * const mt8195_dwmac_clk_l[] = {
+ "axi", "apb", "mac_cg", "mac_main", "ptp_ref", "rmii_internal"
+};
+
static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
{
int rmii_clk_from_mac = plat->rmii_clk_from_mac ? RMII_CLK_SRC_INTERNAL : 0;
@@ -267,6 +300,204 @@ static const struct mediatek_dwmac_variant mt2712_gmac_variant = {
.tx_delay_max = 17600,
};
+static int mt8195_set_interface(struct mediatek_dwmac_plat_data *plat)
+{
+ int rmii_clk_from_mac = plat->rmii_clk_from_mac ? MT8195_RMII_CLK_SRC_INTERNAL : 0;
+ int rmii_rxc = plat->rmii_rxc ? MT8195_RMII_CLK_SRC_RXC : 0;
+ u32 intf_val = 0;
+
+ /* The clock labeled as "rmii_internal" in mt8195_dwmac_clk_l is needed
+ * only in RMII(when MAC provides the reference clock), and useless for
+ * RGMII/MII/RMII(when PHY provides the reference clock).
+ * num_clks_to_config indicates the real number of clocks should be
+ * configured, equals to (plat->variant->num_clks - 1) in default for all the case,
+ * then +1 for rmii_clk_from_mac case.
+ */
+ plat->num_clks_to_config = plat->variant->num_clks - 1;
+
+ /* select phy interface in top control domain */
+ switch (plat->phy_mode) {
+ case PHY_INTERFACE_MODE_MII:
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_MII);
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ if (plat->rmii_clk_from_mac)
+ plat->num_clks_to_config++;
+ intf_val |= (rmii_rxc | rmii_clk_from_mac);
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_RMII);
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_RGMII);
+ break;
+ default:
+ dev_err(plat->dev, "phy interface not supported\n");
+ return -EINVAL;
+ }
+
+ /* MT8195 only support external PHY */
+ intf_val |= MT8195_EXT_PHY_MODE;
+
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL0, intf_val);
+
+ return 0;
+}
+
+static void mt8195_delay_ps2stage(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+
+ /* 290ps per stage */
+ mac_delay->tx_delay /= 290;
+ mac_delay->rx_delay /= 290;
+}
+
+static void mt8195_delay_stage2ps(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+
+ /* 290ps per stage */
+ mac_delay->tx_delay *= 290;
+ mac_delay->rx_delay *= 290;
+}
+
+static int mt8195_set_delay(struct mediatek_dwmac_plat_data *plat)
+{
+ struct mac_delay_struct *mac_delay = &plat->mac_delay;
+ u32 gtxc_delay_val, delay_val = 0, rmii_delay_val = 0;
+
+ mt8195_delay_ps2stage(plat);
+
+ switch (plat->phy_mode) {
+ case PHY_INTERFACE_MODE_MII:
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE, !!mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES, mac_delay->tx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV, mac_delay->tx_inv);
+
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay->rx_inv);
+ break;
+ case PHY_INTERFACE_MODE_RMII:
+ if (plat->rmii_clk_from_mac) {
+ /* case 1: mac provides the rmii reference clock,
+ * and the clock output to TXC pin.
+ * The egress timing can be adjusted by RMII_TXC delay macro circuit.
+ * The ingress timing can be adjusted by RMII_RXC delay macro circuit.
+ */
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_ENABLE,
+ !!mac_delay->tx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_STAGES,
+ mac_delay->tx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_INV,
+ mac_delay->tx_inv);
+
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_ENABLE,
+ !!mac_delay->rx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_STAGES,
+ mac_delay->rx_delay);
+ rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_INV,
+ mac_delay->rx_inv);
+ } else {
+ /* case 2: the rmii reference clock is from external phy,
+ * and the property "rmii_rxc" indicates which pin(TXC/RXC)
+ * the reference clk is connected to. The reference clock is a
+ * received signal, so rx_delay/rx_inv are used to indicate
+ * the reference clock timing adjustment
+ */
+ if (plat->rmii_rxc) {
+ /* the rmii reference clock from outside is connected
+ * to RXC pin, the reference clock will be adjusted
+ * by RXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE,
+ !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES,
+ mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV,
+ mac_delay->rx_inv);
+ } else {
+ /* the rmii reference clock from outside is connected
+ * to TXC pin, the reference clock will be adjusted
+ * by TXC delay macro circuit.
+ */
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE,
+ !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES,
+ mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV,
+ mac_delay->rx_inv);
+ }
+ }
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_ENABLE, !!mac_delay->tx_delay);
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_STAGES, mac_delay->tx_delay);
+ gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_INV, mac_delay->tx_inv);
+
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES, mac_delay->rx_delay);
+ delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay->rx_inv);
+
+ break;
+ default:
+ dev_err(plat->dev, "phy interface not supported\n");
+ return -EINVAL;
+ }
+
+ regmap_update_bits(plat->peri_regmap,
+ MT8195_PERI_ETH_CTRL0,
+ MT8195_RGMII_TXC_PHASE_CTRL |
+ MT8195_DLY_GTXC_INV |
+ MT8195_DLY_GTXC_ENABLE |
+ MT8195_DLY_GTXC_STAGES,
+ gtxc_delay_val);
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL1, delay_val);
+ regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL2, rmii_delay_val);
+
+ mt8195_delay_stage2ps(plat);
+
+ return 0;
+}
+
+static void mt8195_fix_mac_speed(void *priv, unsigned int speed)
+{
+ struct mediatek_dwmac_plat_data *priv_plat = priv;
+
+ if ((phy_interface_mode_is_rgmii(priv_plat->phy_mode))) {
+ /* prefer 2ns fixed delay which is controlled by TXC_PHASE_CTRL,
+ * when link speed is 1Gbps with RGMII interface,
+ * Fall back to delay macro circuit for 10/100Mbps link speed.
+ */
+ if (speed == SPEED_1000)
+ regmap_update_bits(priv_plat->peri_regmap,
+ MT8195_PERI_ETH_CTRL0,
+ MT8195_RGMII_TXC_PHASE_CTRL |
+ MT8195_DLY_GTXC_ENABLE |
+ MT8195_DLY_GTXC_INV |
+ MT8195_DLY_GTXC_STAGES,
+ MT8195_RGMII_TXC_PHASE_CTRL);
+ else
+ mt8195_set_delay(priv_plat);
+ }
+}
+
+static const struct mediatek_dwmac_variant mt8195_gmac_variant = {
+ .dwmac_set_phy_interface = mt8195_set_interface,
+ .dwmac_set_delay = mt8195_set_delay,
+ .dwmac_fix_mac_speed = mt8195_fix_mac_speed,
+ .clk_list = mt8195_dwmac_clk_l,
+ .num_clks = ARRAY_SIZE(mt8195_dwmac_clk_l),
+ .dma_bit_mask = 35,
+ .rx_delay_max = 9280,
+ .tx_delay_max = 9280,
+};
+
static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
{
struct mac_delay_struct *mac_delay = &plat->mac_delay;
@@ -307,6 +538,7 @@ static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
mac_delay->rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse");
plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc");
plat->rmii_clk_from_mac = of_property_read_bool(plat->np, "mediatek,rmii-clk-from-mac");
+ plat->mac_wol = of_property_read_bool(plat->np, "mediatek,mac-wol");
return 0;
}
@@ -383,6 +615,7 @@ static int mediatek_dwmac_clks_config(void *priv, bool enabled)
return ret;
}
+
static int mediatek_dwmac_probe(struct platform_device *pdev)
{
struct mediatek_dwmac_plat_data *priv_plat;
@@ -420,7 +653,7 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
return PTR_ERR(plat_dat);
plat_dat->interface = priv_plat->phy_mode;
- plat_dat->use_phy_wol = 1;
+ plat_dat->use_phy_wol = priv_plat->mac_wol ? 0 : 1;
plat_dat->riwt_off = 1;
plat_dat->maxmtu = ETH_DATA_LEN;
plat_dat->addr64 = priv_plat->variant->dma_bit_mask;
@@ -428,7 +661,23 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
plat_dat->init = mediatek_dwmac_init;
plat_dat->exit = mediatek_dwmac_exit;
plat_dat->clks_config = mediatek_dwmac_clks_config;
+ if (priv_plat->variant->dwmac_fix_mac_speed)
+ plat_dat->fix_mac_speed = priv_plat->variant->dwmac_fix_mac_speed;
+ plat_dat->safety_feat_cfg = devm_kzalloc(&pdev->dev,
+ sizeof(*plat_dat->safety_feat_cfg),
+ GFP_KERNEL);
+ if (!plat_dat->safety_feat_cfg)
+ return -ENOMEM;
+ plat_dat->safety_feat_cfg->tsoee = 1;
+ plat_dat->safety_feat_cfg->mrxpee = 0;
+ plat_dat->safety_feat_cfg->mestee = 1;
+ plat_dat->safety_feat_cfg->mrxee = 1;
+ plat_dat->safety_feat_cfg->mtxee = 1;
+ plat_dat->safety_feat_cfg->epsi = 0;
+ plat_dat->safety_feat_cfg->edpp = 1;
+ plat_dat->safety_feat_cfg->prtyen = 1;
+ plat_dat->safety_feat_cfg->tmouten = 1;
mediatek_dwmac_init(pdev, priv_plat);
ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
@@ -443,6 +692,8 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
static const struct of_device_id mediatek_dwmac_match[] = {
{ .compatible = "mediatek,mt2712-gmac",
.data = &mt2712_gmac_variant },
+ { .compatible = "mediatek,mt8195-gmac",
+ .data = &mt8195_gmac_variant },
{ }
};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v5 6/7] arm64: dts: mt8195: add ethernet device node
2021-12-07 1:54 [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Biao Huang
` (4 preceding siblings ...)
2021-12-07 1:55 ` [PATCH v5 5/7] net-next: stmmac: dwmac-mediatek: add support for mt8195 Biao Huang
@ 2021-12-07 1:55 ` Biao Huang
2021-12-07 1:55 ` [PATCH v5 7/7] net-next: dt-bindings: dwmac: add support for mt8195 Biao Huang
2021-12-07 14:43 ` [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Jakub Kicinski
7 siblings, 0 replies; 12+ messages in thread
From: Biao Huang @ 2021-12-07 1:55 UTC (permalink / raw)
To: davem, Jakub Kicinski, Rob Herring
Cc: Matthias Brugger, Giuseppe Cavallaro, Alexandre Torgue,
Jose Abreu, Maxime Coquelin, Biao Huang, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
This patch adds device node for mt8195 ethernet.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
---
arch/arm64/boot/dts/mediatek/mt8195-evb.dts | 92 +++++++++++++++++++++
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 70 ++++++++++++++++
2 files changed, 162 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
index 5cce9a5d3163..d90308f80229 100644
--- a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
@@ -5,6 +5,8 @@
*/
/dts-v1/;
#include "mt8195.dtsi"
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "MediaTek MT8195 evaluation board";
@@ -32,6 +34,96 @@ reserved_memory: reserved-memory {
};
};
+ð {
+ phy-mode ="rgmii-rxid";
+ phy-handle = <ð_phy0>;
+ snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>;
+ snps,reset-delays-us = <0 10000 10000>;
+ mediatek,tx-delay-ps = <2030>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <ð_default>;
+ pinctrl-1 = <ð_sleep>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ eth_phy0: eth_phy0@1 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0x1>;
+ };
+ };
+};
+
+&pio {
+ eth_default: eth_default {
+ txd_pins {
+ pinmux = <PINMUX_GPIO77__FUNC_GBE_TXD3>,
+ <PINMUX_GPIO78__FUNC_GBE_TXD2>,
+ <PINMUX_GPIO79__FUNC_GBE_TXD1>,
+ <PINMUX_GPIO80__FUNC_GBE_TXD0>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+ cc_pins {
+ pinmux = <PINMUX_GPIO85__FUNC_GBE_TXC>,
+ <PINMUX_GPIO88__FUNC_GBE_TXEN>,
+ <PINMUX_GPIO87__FUNC_GBE_RXDV>,
+ <PINMUX_GPIO86__FUNC_GBE_RXC>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+ rxd_pins {
+ pinmux = <PINMUX_GPIO81__FUNC_GBE_RXD3>,
+ <PINMUX_GPIO82__FUNC_GBE_RXD2>,
+ <PINMUX_GPIO83__FUNC_GBE_RXD1>,
+ <PINMUX_GPIO84__FUNC_GBE_RXD0>;
+ };
+ mdio_pins {
+ pinmux = <PINMUX_GPIO89__FUNC_GBE_MDC>,
+ <PINMUX_GPIO90__FUNC_GBE_MDIO>;
+ input-enable;
+ };
+ power_pins {
+ pinmux = <PINMUX_GPIO91__FUNC_GPIO91>,
+ <PINMUX_GPIO92__FUNC_GPIO92>;
+ output-high;
+ };
+ };
+
+ eth_sleep: eth_sleep {
+ txd_pins {
+ pinmux = <PINMUX_GPIO77__FUNC_GPIO77>,
+ <PINMUX_GPIO78__FUNC_GPIO78>,
+ <PINMUX_GPIO79__FUNC_GPIO79>,
+ <PINMUX_GPIO80__FUNC_GPIO80>;
+ };
+ cc_pins {
+ pinmux = <PINMUX_GPIO85__FUNC_GPIO85>,
+ <PINMUX_GPIO88__FUNC_GPIO88>,
+ <PINMUX_GPIO87__FUNC_GPIO87>,
+ <PINMUX_GPIO86__FUNC_GPIO86>;
+ };
+ rxd_pins {
+ pinmux = <PINMUX_GPIO81__FUNC_GPIO81>,
+ <PINMUX_GPIO82__FUNC_GPIO82>,
+ <PINMUX_GPIO83__FUNC_GPIO83>,
+ <PINMUX_GPIO84__FUNC_GPIO84>;
+ };
+ mdio_pins {
+ pinmux = <PINMUX_GPIO89__FUNC_GPIO89>,
+ <PINMUX_GPIO90__FUNC_GPIO90>;
+ input-disable;
+ bias-disable;
+ };
+ power_pins {
+ pinmux = <PINMUX_GPIO91__FUNC_GPIO91>,
+ <PINMUX_GPIO92__FUNC_GPIO92>;
+ input-disable;
+ bias-disable;
+ };
+ };
+};
+
&uart0 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
index a59c0e9d1fc2..f30a60dca5ef 100644
--- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
@@ -823,6 +823,76 @@ spis1: spi@1101e000 {
status = "disabled";
};
+ eth: ethernet@11021000 {
+ compatible = "mediatek,mt8195-gmac", "snps,dwmac-5.10a";
+ reg = <0 0x11021000 0 0x4000>;
+ interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "macirq";
+ mac-address = [00 55 7b b5 7d f7];
+ clock-names = "axi",
+ "apb",
+ "mac_cg",
+ "mac_main",
+ "ptp_ref",
+ "rmii_internal";
+ clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>,
+ <&pericfg_ao CLK_PERI_AO_ETHERNET_BUS>,
+ <&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>,
+ <&topckgen CLK_TOP_SNPS_ETH_250M>,
+ <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>,
+ <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>;
+ assigned-clocks = <&topckgen CLK_TOP_SNPS_ETH_250M>,
+ <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>,
+ <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>;
+ assigned-clock-parents = <&topckgen CLK_TOP_ETHPLL_D2>,
+ <&topckgen CLK_TOP_ETHPLL_D8>,
+ <&topckgen CLK_TOP_ETHPLL_D10>;
+ power-domains = <&spm MT8195_POWER_DOMAIN_ETHER>;
+ mediatek,pericfg = <&infracfg_ao>;
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+ snps,txpbl = <16>;
+ snps,rxpbl = <16>;
+ clk_csr = <0>;
+ status = "disabled";
+
+ stmmac_axi_setup: stmmac-axi-config {
+ snps,wr_osr_lmt = <0x7>;
+ snps,rd_osr_lmt = <0x7>;
+ snps,blen = <0 0 0 0 16 8 4>;
+ };
+
+ mtl_rx_setup: rx-queues-config {
+ snps,rx-queues-to-use = <1>;
+ snps,rx-sched-sp;
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,priority = <0x0>;
+ };
+ };
+ mtl_tx_setup: tx-queues-config {
+ snps,tx-queues-to-use = <3>;
+ snps,tx-sched-wrr;
+ queue0 {
+ snps,weight = <0x10>;
+ snps,dcb-algorithm;
+ snps,priority = <0x0>;
+ };
+ queue1 {
+ snps,weight = <0x11>;
+ snps,dcb-algorithm;
+ snps,priority = <0x1>;
+ };
+ queue2 {
+ snps,weight = <0x12>;
+ snps,dcb-algorithm;
+ snps,priority = <0x2>;
+ };
+ };
+ };
+
mmc0: mmc@11230000 {
compatible = "mediatek,mt8195-mmc", "mediatek,mt8192-mmc";
reg = <0 0x11230000 0 0x10000>,
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v5 7/7] net-next: dt-bindings: dwmac: add support for mt8195
2021-12-07 1:54 [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Biao Huang
` (5 preceding siblings ...)
2021-12-07 1:55 ` [PATCH v5 6/7] arm64: dts: mt8195: add ethernet device node Biao Huang
@ 2021-12-07 1:55 ` Biao Huang
2021-12-07 14:43 ` [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Jakub Kicinski
7 siblings, 0 replies; 12+ messages in thread
From: Biao Huang @ 2021-12-07 1:55 UTC (permalink / raw)
To: davem, Jakub Kicinski, Rob Herring
Cc: Matthias Brugger, Giuseppe Cavallaro, Alexandre Torgue,
Jose Abreu, Maxime Coquelin, Biao Huang, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
Add binding document for the ethernet on mt8195.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
---
.../bindings/net/mediatek-dwmac.yaml | 86 +++++++++++++++----
1 file changed, 70 insertions(+), 16 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
index 9207266a6e69..fb04166404d8 100644
--- a/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
+++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
@@ -19,11 +19,67 @@ select:
contains:
enum:
- mediatek,mt2712-gmac
+ - mediatek,mt8195-gmac
required:
- compatible
allOf:
- $ref: "snps,dwmac.yaml#"
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - mediatek,mt2712-gmac
+
+ then:
+ properties:
+ clocks:
+ minItems: 5
+ items:
+ - description: AXI clock
+ - description: APB clock
+ - description: MAC Main clock
+ - description: PTP clock
+ - description: RMII reference clock provided by MAC
+
+ clock-names:
+ minItems: 5
+ items:
+ - const: axi
+ - const: apb
+ - const: mac_main
+ - const: ptp_ref
+ - const: rmii_internal
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - mediatek,mt8195-gmac
+
+ then:
+ properties:
+ clocks:
+ minItems: 6
+ items:
+ - description: AXI clock
+ - description: APB clock
+ - description: MAC clock gate
+ - description: MAC Main clock
+ - description: PTP clock
+ - description: RMII reference clock provided by MAC
+
+ clock-names:
+ minItems: 6
+ items:
+ - const: axi
+ - const: apb
+ - const: mac_cg
+ - const: mac_main
+ - const: ptp_ref
+ - const: rmii_internal
properties:
compatible:
@@ -32,22 +88,10 @@ properties:
- enum:
- mediatek,mt2712-gmac
- const: snps,dwmac-4.20a
-
- clocks:
- items:
- - description: AXI clock
- - description: APB clock
- - description: MAC Main clock
- - description: PTP clock
- - description: RMII reference clock provided by MAC
-
- clock-names:
- items:
- - const: axi
- - const: apb
- - const: mac_main
- - const: ptp_ref
- - const: rmii_internal
+ - items:
+ - enum:
+ - mediatek,mt8195-gmac
+ - const: snps,dwmac-5.10a
mediatek,pericfg:
$ref: /schemas/types.yaml#/definitions/phandle
@@ -62,6 +106,8 @@ properties:
or will round down. Range 0~31*170.
For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
or will round down. Range 0~31*550.
+ For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290,
+ or will round down. Range 0~31*290.
mediatek,rx-delay-ps:
description:
@@ -70,6 +116,8 @@ properties:
or will round down. Range 0~31*170.
For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
or will round down. Range 0~31*550.
+ For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple
+ of 290, or will round down. Range 0~31*290.
mediatek,rmii-rxc:
type: boolean
@@ -103,6 +151,12 @@ properties:
3. the inside clock, which be sent to MAC, will be inversed in RMII case when
the reference clock is from MAC.
+ mediatek,mac-wol:
+ type: boolean
+ description:
+ If present, indicates that MAC supports WOL(Wake-On-LAN), and MAC WOL will be enabled.
+ Otherwise, PHY WOL is perferred.
+
required:
- compatible
- reg
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195
2021-12-07 1:54 [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Biao Huang
` (6 preceding siblings ...)
2021-12-07 1:55 ` [PATCH v5 7/7] net-next: dt-bindings: dwmac: add support for mt8195 Biao Huang
@ 2021-12-07 14:43 ` Jakub Kicinski
2021-12-07 14:46 ` Jakub Kicinski
7 siblings, 1 reply; 12+ messages in thread
From: Jakub Kicinski @ 2021-12-07 14:43 UTC (permalink / raw)
To: Biao Huang
Cc: davem, Rob Herring, Matthias Brugger, Giuseppe Cavallaro,
Alexandre Torgue, Jose Abreu, Maxime Coquelin, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
On Tue, 7 Dec 2021 09:54:58 +0800 Biao Huang wrote:
> Changes in v5:
> 1. remove useless inclusion in dwmac-mediatek.c as Angelo's comments.
> 2. add acked-by in "net-next: stmmac: dwmac-mediatek: add support for
> mt8195" patch
Which tree is this series based on? It doesn't seem to apply to
net-next. Also the net-next in the subjects is misplaced. If the series
is supposed to be merged to net-next the subject should be like:
[PATCH net-next v5 1/7] stmmac: dwmac-mediatek: add platform level clocks management
You can use --subject-prefix="PATCH net-next v6" in git-format-patch to
add the prefix.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195
2021-12-07 14:43 ` [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195 Jakub Kicinski
@ 2021-12-07 14:46 ` Jakub Kicinski
2021-12-08 1:20 ` Biao Huang
0 siblings, 1 reply; 12+ messages in thread
From: Jakub Kicinski @ 2021-12-07 14:46 UTC (permalink / raw)
To: Biao Huang
Cc: davem, Rob Herring, Matthias Brugger, Giuseppe Cavallaro,
Alexandre Torgue, Jose Abreu, Maxime Coquelin, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
On Tue, 7 Dec 2021 06:43:45 -0800 Jakub Kicinski wrote:
> On Tue, 7 Dec 2021 09:54:58 +0800 Biao Huang wrote:
> > Changes in v5:
> > 1. remove useless inclusion in dwmac-mediatek.c as Angelo's comments.
> > 2. add acked-by in "net-next: stmmac: dwmac-mediatek: add support for
> > mt8195" patch
>
> Which tree is this series based on? It doesn't seem to apply to
> net-next. Also the net-next in the subjects is misplaced. If the series
> is supposed to be merged to net-next the subject should be like:
>
> [PATCH net-next v5 1/7] stmmac: dwmac-mediatek: add platform level clocks management
>
> You can use --subject-prefix="PATCH net-next v6" in git-format-patch to
> add the prefix.
FWIW patch 6 is the one with the conflict: "arm64: dts: mt8195: add
ethernet device node"
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v5 0/7] MediaTek Ethernet Patches on MT8195
2021-12-07 14:46 ` Jakub Kicinski
@ 2021-12-08 1:20 ` Biao Huang
0 siblings, 0 replies; 12+ messages in thread
From: Biao Huang @ 2021-12-08 1:20 UTC (permalink / raw)
To: Jakub Kicinski
Cc: davem, Rob Herring, Matthias Brugger, Giuseppe Cavallaro,
Alexandre Torgue, Jose Abreu, Maxime Coquelin, netdev, devicetree,
linux-kernel, linux-arm-kernel, linux-mediatek, linux-stm32,
srv_heupstream, macpaul.lin, angelogioacchino.delregno, dkirjanov
Dear Jakub,
Thanks for your comments~
On Tue, 2021-12-07 at 06:46 -0800, Jakub Kicinski wrote:
> On Tue, 7 Dec 2021 06:43:45 -0800 Jakub Kicinski wrote:
> > On Tue, 7 Dec 2021 09:54:58 +0800 Biao Huang wrote:
> > > Changes in v5:
> > > 1. remove useless inclusion in dwmac-mediatek.c as Angelo's
> > > comments.
> > > 2. add acked-by in "net-next: stmmac: dwmac-mediatek: add support
> > > for
> > > mt8195" patch
> >
> > Which tree is this series based on? It doesn't seem to apply to
> > net-next. Also the net-next in the subjects is misplaced. If the
> > series
> > is supposed to be merged to net-next the subject should be like:
> >
> > [PATCH net-next v5 1/7] stmmac: dwmac-mediatek: add platform level
> > clocks management
> >
> > You can use --subject-prefix="PATCH net-next v6" in git-format-
> > patch to
> > add the prefix.
>
> FWIW patch 6 is the one with the conflict: "arm64: dts: mt8195: add
> ethernet device node"
I'll rebase to the latest net-next tree, and fix these issues in next
send
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread