[PATCH v4 00/15] Add support for Microchip LAN969x

[PATCH v4 00/15] Add support for Microchip LAN969x

[Robert Marko]

This series adds support for the Microchip LAN969x switch SoC family.

Series is a bit long since after discussions in previous versions, it was
recommended[1][2] to add SoC specific compatibles for device nodes so it
includes the required bindings updates.

[1] https://lore.kernel.org/all/20251203-splendor-cubbyhole-eda2d6982b46@spud/
[2] https://lore.kernel.org/all/173412c8-c2fb-4c38-8de7-5b1c2eebdbf9@microchip.com/
[3] https://lore.kernel.org/all/20251203-duly-leotard-86b83bd840c6@spud/
[4] https://lore.kernel.org/all/756ead5d-8c9b-480d-8ae5-71667575ab7c@kernel.org/

Signed-off-by: Robert Marko <robert.marko@sartura.hr>

Changes in v4:
* Pick Acked-by from Andi for I2C bindings
* Move clock indexes from dt-bindings into a DTS header as suggested by
Krzysztof[4]

Changes in v3:
* Pick Acked-by from Conor
* Drop HWMON binding as it was picked into hwmon already
* Document EV23X71A into AT91 binding
* Drop SparX-5 and AT91 bindings merge
* Apply remark from Conor on DMA binding regarding merging cases

Changes in v2:
* Change LAN969x wildcards to LAN9691 in patches
* Split SoC DTSI and evaluation board patches
* Add the suggested binding changes required for SoC specific compatibles
* Merge SparX-5 and AT91 bindings as suggested[3]

Robert Marko (15):
  dt-bindings: usb: Add Microchip LAN969x support
  dt-bindings: mfd: atmel,sama5d2-flexcom: add microchip,lan9691-flexcom
  dt-bindings: serial: atmel,at91-usart: add microchip,lan9691-usart
  dt-bindings: spi: at91: add microchip,lan9691-spi
  dt-bindings: i2c: atmel,at91sam: add microchip,lan9691-i2c
  dt-bindings: rng: atmel,at91-trng: add microchip,lan9691-trng
  dt-bindings: crypto: atmel,at91sam9g46-aes: add microchip,lan9691-aes
  dt-bindings: crypto: atmel,at91sam9g46-sha: add microchip,lan9691-sha
  dt-bindings: dma: atmel: add microchip,lan9691-dma
  dt-bindings: net: mscc-miim: add microchip,lan9691-miim
  dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x
  arm64: dts: microchip: add LAN969x clock header file
  arm64: dts: microchip: add LAN969x support
  dt-bindings: arm: AT91: document EV23X71A board
  arm64: dts: microchip: add EV23X71A board

 .../devicetree/bindings/arm/atmel-at91.yaml   |   6 +
 .../crypto/atmel,at91sam9g46-aes.yaml         |   1 +
 .../crypto/atmel,at91sam9g46-sha.yaml         |   1 +
 .../bindings/dma/atmel,sama5d4-dma.yaml       |   4 +-
 .../bindings/i2c/atmel,at91sam-i2c.yaml       |   1 +
 .../bindings/mfd/atmel,sama5d2-flexcom.yaml   |   1 +
 .../devicetree/bindings/net/mscc,miim.yaml    |  11 +-
 .../pinctrl/microchip,sparx5-sgpio.yaml       |  20 +-
 .../bindings/rng/atmel,at91-trng.yaml         |   1 +
 .../bindings/serial/atmel,at91-usart.yaml     |   1 +
 .../bindings/spi/atmel,at91rm9200-spi.yaml    |   1 +
 .../bindings/usb/microchip,lan9691-dwc3.yaml  |  66 ++
 arch/arm64/boot/dts/microchip/Makefile        |   1 +
 arch/arm64/boot/dts/microchip/clk-lan9691.h   |  24 +
 arch/arm64/boot/dts/microchip/lan9691.dtsi    | 488 +++++++++++
 .../boot/dts/microchip/lan9696-ev23x71a.dts   | 757 ++++++++++++++++++
 16 files changed, 1375 insertions(+), 9 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/microchip,lan9691-dwc3.yaml
 create mode 100644 arch/arm64/boot/dts/microchip/clk-lan9691.h
 create mode 100644 arch/arm64/boot/dts/microchip/lan9691.dtsi
 create mode 100644 arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts

-- 
2.52.0

[PATCH v4 01/15] dt-bindings: usb: Add Microchip LAN969x support

[Robert Marko]

Microchip LAN969x has DWC3 compatible controller, though limited to 2.0(HS)
speed, so document it.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
Changes in v2:
* Fix example indentation

 .../bindings/usb/microchip,lan9691-dwc3.yaml  | 66 +++++++++++++++++++
 1 file changed, 66 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/microchip,lan9691-dwc3.yaml

diff --git a/Documentation/devicetree/bindings/usb/microchip,lan9691-dwc3.yaml b/Documentation/devicetree/bindings/usb/microchip,lan9691-dwc3.yaml
new file mode 100644
index 000000000000..08113eac74b8
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/microchip,lan9691-dwc3.yaml
@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/microchip,lan9691-dwc3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip LAN969x SuperSpeed DWC3 USB SoC controller
+
+maintainers:
+  - Robert Marko <robert.marko@sartura.hr>
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - microchip,lan9691-dwc3
+  required:
+    - compatible
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - microchip,lan9691-dwc3
+      - const: snps,dwc3
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Gated USB DRD clock
+      - description: Controller reference clock
+
+  clock-names:
+    items:
+      - const: bus_early
+      - const: ref
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+allOf:
+  - $ref: snps,dwc3.yaml#
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    usb@300000 {
+        compatible = "microchip,lan9691-dwc3", "snps,dwc3";
+        reg = <0x300000 0x80000>;
+        interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&clks 12>, <&clks 11>;
+        clock-names = "bus_early", "ref";
+    };
-- 
2.52.0

[PATCH v4 02/15] dt-bindings: mfd: atmel,sama5d2-flexcom: add microchip,lan9691-flexcom

[Robert Marko]

Add binding documentation for Microchip LAN969x.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml b/Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml
index c7d6cf96796c..5e5dec2f6564 100644
--- a/Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml
+++ b/Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml
@@ -20,6 +20,7 @@ properties:
       - const: atmel,sama5d2-flexcom
       - items:
           - enum:
+              - microchip,lan9691-flexcom
               - microchip,sam9x7-flexcom
               - microchip,sama7d65-flexcom
               - microchip,sama7g5-flexcom
-- 
2.52.0

[PATCH v4 03/15] dt-bindings: serial: atmel,at91-usart: add microchip,lan9691-usart

[Robert Marko]

Document Microchip LAN969x USART compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml b/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml
index 087a8926f8b4..375cd50bc5cc 100644
--- a/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml
+++ b/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml
@@ -24,6 +24,7 @@ properties:
           - const: atmel,at91sam9260-usart
       - items:
           - enum:
+              - microchip,lan9691-usart
               - microchip,sam9x60-usart
               - microchip,sam9x7-usart
               - microchip,sama7d65-usart
-- 
2.52.0

[PATCH v4 04/15] dt-bindings: spi: at91: add microchip,lan9691-spi

[Robert Marko]

Document Microchip LAN969x SPI compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/spi/atmel,at91rm9200-spi.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/spi/atmel,at91rm9200-spi.yaml b/Documentation/devicetree/bindings/spi/atmel,at91rm9200-spi.yaml
index 11885d0cc209..a8539b68a2f3 100644
--- a/Documentation/devicetree/bindings/spi/atmel,at91rm9200-spi.yaml
+++ b/Documentation/devicetree/bindings/spi/atmel,at91rm9200-spi.yaml
@@ -19,6 +19,7 @@ properties:
       - const: atmel,at91rm9200-spi
       - items:
           - enum:
+              - microchip,lan9691-spi
               - microchip,sam9x60-spi
               - microchip,sam9x7-spi
               - microchip,sama7d65-spi
-- 
2.52.0

[PATCH v4 05/15] dt-bindings: i2c: atmel,at91sam: add microchip,lan9691-i2c

[Robert Marko]

Document Microchip LAN969x I2C compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
---
Changes in v4:
* Pick Acked-by from Andi

Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml b/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
index e61cdb5b16ef..c83674c3183b 100644
--- a/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/atmel,at91sam-i2c.yaml
@@ -26,6 +26,7 @@ properties:
               - microchip,sam9x60-i2c
       - items:
           - enum:
+              - microchip,lan9691-i2c
               - microchip,sama7d65-i2c
               - microchip,sama7g5-i2c
               - microchip,sam9x7-i2c
-- 
2.52.0

[PATCH v4 06/15] dt-bindings: rng: atmel,at91-trng: add microchip,lan9691-trng

[Robert Marko]

Document Microchip LAN9696X TRNG compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml b/Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml
index f78614100ea8..3628251b8c51 100644
--- a/Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml
+++ b/Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml
@@ -19,6 +19,7 @@ properties:
           - microchip,sam9x60-trng
       - items:
           - enum:
+              - microchip,lan9691-trng
               - microchip,sama7g5-trng
           - const: atmel,at91sam9g45-trng
       - items:
-- 
2.52.0

[PATCH v4 07/15] dt-bindings: crypto: atmel,at91sam9g46-aes: add microchip,lan9691-aes

[Robert Marko]

Document Microchip LAN969x AES compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Pick Acked-by from Conor

 .../devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml b/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml
index 19010f90198a..f3b6af6baf15 100644
--- a/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml
+++ b/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml
@@ -16,6 +16,7 @@ properties:
       - const: atmel,at91sam9g46-aes
       - items:
           - enum:
+              - microchip,lan9691-aes
               - microchip,sam9x7-aes
               - microchip,sama7d65-aes
           - const: atmel,at91sam9g46-aes
-- 
2.52.0

[PATCH v4 08/15] dt-bindings: crypto: atmel,at91sam9g46-sha: add microchip,lan9691-sha

[Robert Marko]

Document Microchip LAN969x SHA compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Pick Acked-by from Conor

 .../devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml b/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml
index 39e076b275b3..16704ff0dd7f 100644
--- a/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml
+++ b/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml
@@ -16,6 +16,7 @@ properties:
       - const: atmel,at91sam9g46-sha
       - items:
           - enum:
+              - microchip,lan9691-sha
               - microchip,sam9x7-sha
               - microchip,sama7d65-sha
           - const: atmel,at91sam9g46-sha
-- 
2.52.0

[PATCH v4 09/15] dt-bindings: dma: atmel: add microchip,lan9691-dma

[Robert Marko]

Document Microchip LAN969x DMA compatible which is compatible to SAMA7G5.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
Changes in v3:
* Merged with microchip,sama7d65-dma since that also falls back to
microchip,sama7g5-dma

 Documentation/devicetree/bindings/dma/atmel,sama5d4-dma.yaml | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/dma/atmel,sama5d4-dma.yaml b/Documentation/devicetree/bindings/dma/atmel,sama5d4-dma.yaml
index 73fc13b902b3..197efb19b07a 100644
--- a/Documentation/devicetree/bindings/dma/atmel,sama5d4-dma.yaml
+++ b/Documentation/devicetree/bindings/dma/atmel,sama5d4-dma.yaml
@@ -33,7 +33,9 @@ properties:
               - microchip,sam9x7-dma
           - const: atmel,sama5d4-dma
       - items:
-          - const: microchip,sama7d65-dma
+          - enum:
+              - microchip,lan9691-dma
+              - microchip,sama7d65-dma
           - const: microchip,sama7g5-dma
 
   "#dma-cells":
-- 
2.52.0

[PATCH v4 10/15] dt-bindings: net: mscc-miim: add microchip,lan9691-miim

[Robert Marko]

Document Microchip LAN969x MIIM compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/net/mscc,miim.yaml | 11 ++++++++---
 1 file changed, 8 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/mscc,miim.yaml b/Documentation/devicetree/bindings/net/mscc,miim.yaml
index 792f26b06b06..2207b33aee76 100644
--- a/Documentation/devicetree/bindings/net/mscc,miim.yaml
+++ b/Documentation/devicetree/bindings/net/mscc,miim.yaml
@@ -14,9 +14,14 @@ allOf:
 
 properties:
   compatible:
-    enum:
-      - mscc,ocelot-miim
-      - microchip,lan966x-miim
+    oneOf:
+      - enum:
+          - mscc,ocelot-miim
+          - microchip,lan966x-miim
+      - items:
+          - enum:
+              - microchip,lan9691-miim
+          - const: mscc,ocelot-miim
 
   "#address-cells":
     const: 1
-- 
2.52.0

[PATCH v4 11/15] dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x

[Robert Marko]

Document LAN969x compatibles for SGPIO.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes in v3:
* Pick Acked-by from Conor

 .../pinctrl/microchip,sparx5-sgpio.yaml       | 20 ++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
index fa47732d7cef..9fbbafcdc063 100644
--- a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
@@ -21,10 +21,15 @@ properties:
     pattern: '^gpio@[0-9a-f]+$'
 
   compatible:
-    enum:
-      - microchip,sparx5-sgpio
-      - mscc,ocelot-sgpio
-      - mscc,luton-sgpio
+    oneOf:
+      - enum:
+          - microchip,sparx5-sgpio
+          - mscc,ocelot-sgpio
+          - mscc,luton-sgpio
+      - items:
+          - enum:
+              - microchip,lan9691-sgpio
+          - const: microchip,sparx5-sgpio
 
   '#address-cells':
     const: 1
@@ -80,7 +85,12 @@ patternProperties:
     type: object
     properties:
       compatible:
-        const: microchip,sparx5-sgpio-bank
+        oneOf:
+          - items:
+              - enum:
+                  - microchip,lan9691-sgpio-bank
+              - const: microchip,sparx5-sgpio-bank
+          - const: microchip,sparx5-sgpio-bank
 
       reg:
         description: |
-- 
2.52.0

[PATCH v4 12/15] arm64: dts: microchip: add LAN969x clock header file

[Robert Marko]

LAN969x uses hardware clock indexes, so document theses in a header to make
them humanly readable.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
Changes in v4:
* Move clock indexes from dt-bindings to a DTS header

Changes in v2:
* Rename file to microchip,lan9691.h

 arch/arm64/boot/dts/microchip/clk-lan9691.h | 24 +++++++++++++++++++++
 1 file changed, 24 insertions(+)
 create mode 100644 arch/arm64/boot/dts/microchip/clk-lan9691.h

diff --git a/arch/arm64/boot/dts/microchip/clk-lan9691.h b/arch/arm64/boot/dts/microchip/clk-lan9691.h
new file mode 100644
index 000000000000..f0006a603747
--- /dev/null
+++ b/arch/arm64/boot/dts/microchip/clk-lan9691.h
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+
+#ifndef _DTS_CLK_LAN9691_H
+#define _DTS_CLK_LAN9691_H
+
+#define GCK_ID_QSPI0		0
+#define GCK_ID_QSPI2		1
+#define GCK_ID_SDMMC0		2
+#define GCK_ID_SDMMC1		3
+#define GCK_ID_MCAN0		4
+#define GCK_ID_MCAN1		5
+#define GCK_ID_FLEXCOM0		6
+#define GCK_ID_FLEXCOM1		7
+#define GCK_ID_FLEXCOM2		8
+#define GCK_ID_FLEXCOM3		9
+#define GCK_ID_TIMER		10
+#define GCK_ID_USB_REFCLK	11
+
+/* Gate clocks */
+#define GCK_GATE_USB_DRD	12
+#define GCK_GATE_MCRAMC		13
+#define GCK_GATE_HMATRIX	14
+
+#endif
-- 
2.52.0

[PATCH v4 13/15] arm64: dts: microchip: add LAN969x support

[Robert Marko]

Add support for Microchip LAN969x switch SoC series by adding the SoC DTSI.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
Changes in v4:
* Adapt to clock indexes now being in a DTS header only

Changes in v2:
* Rename to lan9691
* Split SoC DTSI and evaluation board commits
* Use SoC specific compatibles for devices
* Alphanumerically sort remaining nodes
* Apply DTS coding style

 arch/arm64/boot/dts/microchip/lan9691.dtsi | 488 +++++++++++++++++++++
 1 file changed, 488 insertions(+)
 create mode 100644 arch/arm64/boot/dts/microchip/lan9691.dtsi

diff --git a/arch/arm64/boot/dts/microchip/lan9691.dtsi b/arch/arm64/boot/dts/microchip/lan9691.dtsi
new file mode 100644
index 000000000000..235e56bebbdb
--- /dev/null
+++ b/arch/arm64/boot/dts/microchip/lan9691.dtsi
@@ -0,0 +1,488 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2025 Microchip Technology Inc. and its subsidiaries.
+ */
+
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/at91-usart.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+#include "clk-lan9691.h"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	model = "Microchip LAN969x";
+	compatible = "microchip,lan9691";
+	interrupt-parent = <&gic>;
+
+	clocks {
+		fx100_clk: fx100-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <320000000>;
+		};
+
+		cpu_clk: cpu-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1000000000>;
+		};
+
+		ddr_clk: ddr-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <600000000>;
+		};
+
+		fabric_clk: fabric-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <250000000>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&l2_0>;
+		};
+
+		l2_0: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Secure Phys IRQ */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Non-secure Phys IRQ */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virt IRQ */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hyp IRQ */
+	};
+
+	axi: axi {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		usb: usb@300000 {
+			compatible = "microchip,lan9691-dwc3", "snps,dwc3";
+			reg = <0x300000 0x80000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks GCK_GATE_USB_DRD>,
+				 <&clks GCK_ID_USB_REFCLK>;
+			clock-names = "bus_early", "ref";
+			assigned-clocks = <&clks GCK_ID_USB_REFCLK>;
+			assigned-clock-rates = <60000000>;
+			maximum-speed = "high-speed";
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		flx0: flexcom@e0040000 {
+			compatible = "microchip,lan9691-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe0040000 0x100>;
+			ranges = <0x0 0xe0040000 0x800>;
+			clocks = <&clks GCK_ID_FLEXCOM0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			usart0: serial@200 {
+				compatible = "microchip,lan9691-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi0: spi@400 {
+				compatible = "microchip,lan9691-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,lan9691-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@e0044000 {
+			compatible = "microchip,lan9691-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe0044000 0x100>;
+			ranges = <0x0 0xe0044000 0x800>;
+			clocks = <&clks GCK_ID_FLEXCOM1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			usart1: serial@200 {
+				compatible = "microchip,lan9691-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi1: spi@400 {
+				compatible = "microchip,lan9691-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,lan9691-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		trng: rng@e0048000 {
+			compatible = "microchip,lan9691-trng", "atmel,at91sam9g45-trng";
+			reg = <0xe0048000 0x100>;
+			clocks = <&fabric_clk>;
+			status = "disabled";
+		};
+
+		aes: crypto@e004c000 {
+			compatible = "microchip,lan9691-aes", "atmel,at91sam9g46-aes";
+			reg = <0xe004c000 0x100>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma AT91_XDMAC_DT_PERID(12)>,
+			       <&dma AT91_XDMAC_DT_PERID(13)>;
+			dma-names = "tx", "rx";
+			clocks = <&fabric_clk>;
+			clock-names = "aes_clk";
+			status = "disabled";
+		};
+
+		flx2: flexcom@e0060000 {
+			compatible = "microchip,lan9691-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe0060000 0x100>;
+			ranges = <0x0 0xe0060000 0x800>;
+			clocks = <&clks GCK_ID_FLEXCOM2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			usart2: serial@200 {
+				compatible = "microchip,lan9691-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(7)>,
+				       <&dma AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi2: spi@400 {
+				compatible = "microchip,lan9691-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(7)>,
+				       <&dma AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@600 {
+				compatible = "microchip,lan9691-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(7)>,
+				       <&dma AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@e0064000 {
+			compatible = "microchip,lan9691-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe0064000 0x100>;
+			ranges = <0x0 0xe0064000 0x800>;
+			clocks = <&clks GCK_ID_FLEXCOM3>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			usart3: serial@200 {
+				compatible = "microchip,lan9691-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(9)>,
+				       <&dma AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi3: spi@400 {
+				compatible = "microchip,lan9691-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(9)>,
+				       <&dma AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@600 {
+				compatible = "microchip,lan9691-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(9)>,
+				       <&dma AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		dma: dma-controller@e0068000 {
+			compatible = "microchip,lan9691-dma", "microchip,sama7g5-dma";
+			reg = <0xe0068000 0x1000>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <16>;
+			#dma-cells = <1>;
+			clocks = <&fabric_clk>;
+			clock-names = "dma_clk";
+		};
+
+		sha: crypto@e006c000 {
+			compatible = "microchip,lan9691-sha", "atmel,at91sam9g46-sha";
+			reg = <0xe006c000 0xec>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma AT91_XDMAC_DT_PERID(14)>;
+			dma-names = "tx";
+			clocks = <&fabric_clk>;
+			clock-names = "sha_clk";
+			status = "disabled";
+		};
+
+		timer: timer@e008c000 {
+			compatible = "snps,dw-apb-timer";
+			reg = <0xe008c000 0x400>;
+			clocks = <&fabric_clk>;
+			clock-names = "timer";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@e0090000 {
+			compatible = "snps,dw-wdt";
+			reg = <0xe0090000 0x1000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&fabric_clk>;
+		};
+
+		cpu_ctrl: syscon@e00c0000 {
+			compatible = "microchip,lan966x-cpu-syscon", "syscon";
+			reg = <0xe00c0000 0x350>;
+		};
+
+		switch: switch@e00c0000 {
+			compatible = "microchip,lan9691-switch";
+			reg = <0xe00c0000 0x0010000>,
+			      <0xe2010000 0x1410000>;
+			reg-names = "cpu", "devices";
+			interrupt-names = "xtr", "fdma", "ptp";
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			status = "disabled";
+		};
+
+		clks: clock-controller@e00c00b4 {
+			compatible = "microchip,lan9691-gck";
+			reg = <0xe00c00b4 0x30>, <0xe00c0308 0x4>;
+			#clock-cells = <1>;
+			clocks = <&cpu_clk>, <&ddr_clk>, <&fx100_clk>;
+			clock-names = "cpu", "ddr", "sys";
+		};
+
+		reset: reset-controller@e201000c {
+			compatible = "microchip,lan9691-switch-reset",
+				     "microchip,lan966x-switch-reset";
+			reg = <0xe201000c 0x4>;
+			reg-names = "gcb";
+			#reset-cells = <1>;
+			cpu-syscon = <&cpu_ctrl>;
+		};
+
+		gpio: pinctrl@e20100d4 {
+			compatible = "microchip,lan9691-pinctrl";
+			reg = <0xe20100d4 0xd4>,
+			      <0xe2010370 0xa8>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 66>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+		};
+
+		mdio0: mdio@e20101a8 {
+			compatible = "microchip,lan9691-miim", "mscc,ocelot-miim";
+			reg = <0xe20101a8 0x24>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&fx100_clk>;
+			status = "disabled";
+		};
+
+		mdio1: mdio@e20101cc {
+			compatible = "microchip,lan9691-miim", "mscc,ocelot-miim";
+			reg = <0xe20101cc 0x24>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&fx100_clk>;
+			status = "disabled";
+		};
+
+		sgpio: gpio@e2010230 {
+			compatible = "microchip,lan9691-sgpio", "microchip,sparx5-sgpio";
+			reg = <0xe2010230 0x118>;
+			clocks = <&fx100_clk>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgpio_in: gpio@0 {
+				compatible = "microchip,lan9691-sgpio-bank",
+					     "microchip,sparx5-sgpio-bank";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+			};
+
+			sgpio_out: gpio@1 {
+				compatible = "microchip,lan9691-sgpio-bank",
+					     "microchip,sparx5-sgpio-bank";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <3>;
+			};
+		};
+
+		tmon: hwmon@e2020100 {
+			compatible = "microchip,lan9691-temp", "microchip,sparx5-temp";
+			reg = <0xe2020100 0xc>;
+			clocks = <&fx100_clk>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		serdes: serdes@e3410000 {
+			compatible = "microchip,lan9691-serdes";
+			reg = <0xe3410000 0x150000>;
+			#phy-cells = <1>;
+			clocks = <&fabric_clk>;
+		};
+
+		gic: interrupt-controller@e8c11000 {
+			compatible = "arm,gic-400";
+			reg = <0xe8c11000 0x1000>, /* Distributor GICD_ */
+			      <0xe8c12000 0x2000>, /* CPU interface GICC_ */
+			      <0xe8c14000 0x2000>, /* Virt interface control */
+			      <0xe8c16000 0x2000>; /* Virt CPU interface */
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+};
-- 
2.52.0

[PATCH v4 14/15] dt-bindings: arm: AT91: document EV23X71A board

[Robert Marko]

Microchip EV23X71A board is an LAN9696 based evaluation board.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
 Documentation/devicetree/bindings/arm/atmel-at91.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
index 3a34b7a2e8d4..b0065e2f3713 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
@@ -241,6 +241,12 @@ properties:
           - const: microchip,lan9668
           - const: microchip,lan966
 
+      - description: Microchip LAN9696 EV23X71A Evaluation Board
+        items:
+          - const: microchip,ev23x71a
+          - const: microchip,lan9696
+          - const: microchip,lan9691
+
       - description: Kontron KSwitch D10 MMT series
         items:
           - enum:
-- 
2.52.0

[PATCH v4 15/15] arm64: dts: microchip: add EV23X71A board

[Robert Marko]

Microchip EV23X71A is an LAN9696 based evaluation board.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
Changes in v2:
* Split from SoC DTSI commit
* Apply DTS coding style
* Enclose array in i2c-mux
* Alphanumericaly sort nodes
* Change management port mode to RGMII-ID 

 arch/arm64/boot/dts/microchip/Makefile        |   1 +
 .../boot/dts/microchip/lan9696-ev23x71a.dts   | 757 ++++++++++++++++++
 2 files changed, 758 insertions(+)
 create mode 100644 arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts

diff --git a/arch/arm64/boot/dts/microchip/Makefile b/arch/arm64/boot/dts/microchip/Makefile
index c6e0313eea0f..09d16fc1ce9a 100644
--- a/arch/arm64/boot/dts/microchip/Makefile
+++ b/arch/arm64/boot/dts/microchip/Makefile
@@ -1,4 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_LAN969X) += lan9696-ev23x71a.dtb
 dtb-$(CONFIG_ARCH_SPARX5) += sparx5_pcb125.dtb
 dtb-$(CONFIG_ARCH_SPARX5) += sparx5_pcb134.dtb sparx5_pcb134_emmc.dtb
 dtb-$(CONFIG_ARCH_SPARX5) += sparx5_pcb135.dtb sparx5_pcb135_emmc.dtb
diff --git a/arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts b/arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts
new file mode 100644
index 000000000000..435df455b078
--- /dev/null
+++ b/arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts
@@ -0,0 +1,757 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2025 Microchip Technology Inc. and its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "lan9691.dtsi"
+
+/ {
+	model = "Microchip EV23X71A";
+	compatible = "microchip,ev23x71a", "microchip,lan9696", "microchip,lan9691";
+
+	aliases {
+		serial0 = &usart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 60 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c3>;
+		idle-state = <0x8>;
+		mux-gpios = <&sgpio_out 0 1 GPIO_ACTIVE_HIGH>,
+			    <&sgpio_out 0 2 GPIO_ACTIVE_HIGH>,
+			    <&sgpio_out 0 3 GPIO_ACTIVE_HIGH>;
+		settle-time-us = <100>;
+
+		i2c_sfp0: i2c@0 {
+			reg = <0x0>;
+		};
+
+		i2c_sfp1: i2c@1 {
+			reg = <0x1>;
+		};
+
+		i2c_sfp2: i2c@2 {
+			reg = <0x2>;
+		};
+
+		i2c_sfp3: i2c@3 {
+			reg = <0x3>;
+		};
+
+		i2c_poe: i2c@7 {
+			reg = <0x7>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-status {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio 61 GPIO_ACTIVE_LOW>;
+		};
+
+		led-sfp1-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <0>;
+			gpios = <&sgpio_out 6 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp1-yellow {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <0>;
+			gpios = <&sgpio_out 6 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp2-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <1>;
+			gpios = <&sgpio_out 7 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp2-yellow {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <1>;
+			gpios = <&sgpio_out 7 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp3-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <2>;
+			gpios = <&sgpio_out 8 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp3-yellow {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <2>;
+			gpios = <&sgpio_out 8 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp4-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <3>;
+			gpios = <&sgpio_out 9 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp4-yellow {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <3>;
+			gpios = <&sgpio_out 9 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&sgpio_out 1 2 GPIO_ACTIVE_LOW>,
+			    <&sgpio_out 1 3 GPIO_ACTIVE_LOW>;
+	};
+
+	sfp0: sfp0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp0>;
+		tx-disable-gpios = <&sgpio_out 6 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in 6 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 6 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 6 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp1: sfp1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		tx-disable-gpios = <&sgpio_out 7 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in 7 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 7 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 7 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp2: sfp2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		tx-disable-gpios = <&sgpio_out 8 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in 8 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 8 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 8 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp3: sfp3 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp3>;
+		tx-disable-gpios = <&sgpio_out 9 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in 9 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 9 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 9 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&gpio {
+	emmc_sd_pins: emmc-sd-pins {
+		/* eMMC_SD - CMD, CLK, D0, D1, D2, D3, D4, D5, D6, D7, RSTN */
+		pins = "GPIO_14", "GPIO_15", "GPIO_16", "GPIO_17",
+		       "GPIO_18", "GPIO_19", "GPIO_20", "GPIO_21",
+		       "GPIO_22", "GPIO_23", "GPIO_24";
+		function = "emmc_sd";
+	};
+
+	fan_pins: fan-pins {
+		pins = "GPIO_25", "GPIO_26";
+		function = "fan";
+	};
+
+	fc0_pins: fc0-pins {
+		pins = "GPIO_3", "GPIO_4";
+		function = "fc";
+	};
+
+	fc2_pins: fc2-pins {
+		pins = "GPIO_64", "GPIO_65", "GPIO_66";
+		function = "fc";
+	};
+
+	fc3_pins: fc3-pins {
+		pins = "GPIO_55", "GPIO_56";
+		function = "fc";
+	};
+
+	mdio_pins: mdio-pins {
+		pins = "GPIO_9", "GPIO_10";
+		function = "miim";
+	};
+
+	mdio_irq_pins: mdio-irq-pins {
+		pins = "GPIO_11";
+		function = "miim_irq";
+	};
+
+	sgpio_pins: sgpio-pins {
+		/* SCK, D0, D1, LD */
+		pins = "GPIO_5", "GPIO_6", "GPIO_7", "GPIO_8";
+		function = "sgpio_a";
+	};
+
+	usb_ulpi_pins: usb-ulpi-pins {
+		pins = "GPIO_30", "GPIO_31", "GPIO_32", "GPIO_33",
+		       "GPIO_34", "GPIO_35", "GPIO_36", "GPIO_37",
+		       "GPIO_38", "GPIO_39", "GPIO_40", "GPIO_41";
+		function = "usb_ulpi";
+	};
+
+	usb_rst_pins: usb-rst-pins {
+		pins = "GPIO_12";
+		function = "usb2phy_rst";
+	};
+
+	usb_over_pins: usb-over-pins {
+		pins = "GPIO_13";
+		function = "usb_over_detect";
+	};
+
+	usb_power_pins: usb-power-pins {
+		pins = "GPIO_1";
+		function = "usb_power";
+	};
+
+	ptp_out_pins: ptp-out-pins {
+		pins = "GPIO_58";
+		function = "ptpsync_4";
+	};
+
+	ptp_ext_pins: ptp-ext-pins {
+		pins = "GPIO_59";
+		function = "ptpsync_5";
+	};
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+};
+
+&flx2 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-0 = <&fc3_pins>;
+	pinctrl-names = "default";
+	i2c-analog-filter;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	i2c-sda-hold-time-ns = <1500>;
+	status = "okay";
+};
+
+&mdio0 {
+	pinctrl-0 = <&mdio_pins>, <&mdio_irq_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&gpio 62 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	phy3: phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <3>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy4: phy@4 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <4>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy5: phy@5 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <5>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy6: phy@6 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy7: phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy8: phy@8 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <8>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy9: phy@9 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <9>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy10: phy@10 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <10>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy11: phy@11 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <11>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy12: phy@12 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <12>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy13: phy@13 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <13>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy14: phy@14 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <14>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy15: phy@15 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <15>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy16: phy@16 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <16>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy17: phy@17 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <17>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy18: phy@18 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <18>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy19: phy@19 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <19>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy20: phy@20 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <20>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy21: phy@21 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <21>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy22: phy@22 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <22>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy23: phy@23 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <23>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy24: phy@24 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <24>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy25: phy@25 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <25>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy26: phy@26 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <26>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy27: phy@27 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <27>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_pins>;
+	pinctrl-names = "default";
+	microchip,sgpio-port-ranges = <0 1>, <6 9>;
+	status = "okay";
+
+	gpio@0 {
+		ngpios = <128>;
+	};
+	gpio@1 {
+		ngpios = <128>;
+	};
+};
+
+&spi2 {
+	pinctrl-0 = <&fc2_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpio 63 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&switch {
+	pinctrl-0 = <&ptp_out_pins>, <&ptp_ext_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ethernet-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port0: port@0 {
+			reg = <0>;
+			phy-handle = <&phy4>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 0>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port1: port@1 {
+			reg = <1>;
+			phy-handle = <&phy5>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 0>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port2: port@2 {
+			reg = <2>;
+			phy-handle = <&phy6>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 0>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port3: port@3 {
+			reg = <3>;
+			phy-handle = <&phy7>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 0>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port4: port@4 {
+			reg = <4>;
+			phy-handle = <&phy8>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 1>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port5: port@5 {
+			reg = <5>;
+			phy-handle = <&phy9>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 1>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port6: port@6 {
+			reg = <6>;
+			phy-handle = <&phy10>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 1>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port7: port@7 {
+			reg = <7>;
+			phy-handle = <&phy11>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 1>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port8: port@8 {
+			reg = <8>;
+			phy-handle = <&phy12>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 2>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port9: port@9 {
+			reg = <9>;
+			phy-handle = <&phy13>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 2>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port10: port@10 {
+			reg = <10>;
+			phy-handle = <&phy14>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 2>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port11: port@11 {
+			reg = <11>;
+			phy-handle = <&phy15>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 2>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port12: port@12 {
+			reg = <12>;
+			phy-handle = <&phy16>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 3>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port13: port@13 {
+			reg = <13>;
+			phy-handle = <&phy17>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 3>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port14: port@14 {
+			reg = <14>;
+			phy-handle = <&phy18>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 3>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port15: port@15 {
+			reg = <15>;
+			phy-handle = <&phy19>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 3>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port16: port@16 {
+			reg = <16>;
+			phy-handle = <&phy20>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 4>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port17: port@17 {
+			reg = <17>;
+			phy-handle = <&phy21>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 4>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port18: port@18 {
+			reg = <18>;
+			phy-handle = <&phy22>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 4>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port19: port@19 {
+			reg = <19>;
+			phy-handle = <&phy23>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 4>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port20: port@20 {
+			reg = <20>;
+			phy-handle = <&phy24>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 5>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port21: port@21 {
+			reg = <21>;
+			phy-handle = <&phy25>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 5>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port22: port@22 {
+			reg = <22>;
+			phy-handle = <&phy26>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 5>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port23: port@23 {
+			reg = <23>;
+			phy-handle = <&phy27>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 5>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port24: port@24 {
+			reg = <24>;
+			phys = <&serdes 6>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp0>;
+			managed = "in-band-status";
+			microchip,bandwidth = <10000>;
+			microchip,sd-sgpio = <24>;
+		};
+
+		port25: port@25 {
+			reg = <25>;
+			phys = <&serdes 7>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp1>;
+			managed = "in-band-status";
+			microchip,bandwidth = <10000>;
+			microchip,sd-sgpio = <28>;
+		};
+
+		port26: port@26 {
+			reg = <26>;
+			phys = <&serdes 8>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp2>;
+			managed = "in-band-status";
+			microchip,bandwidth = <10000>;
+			microchip,sd-sgpio = <32>;
+		};
+
+		port27: port@27 {
+			reg = <27>;
+			phys = <&serdes 9>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp3>;
+			managed = "in-band-status";
+			microchip,bandwidth = <10000>;
+			microchip,sd-sgpio = <36>;
+		};
+
+		port29: port@29 {
+			reg = <29>;
+			phys = <&serdes 11>;
+			phy-handle = <&phy3>;
+			phy-mode = "rgmii-id";
+			microchip,bandwidth = <1000>;
+		};
+	};
+};
+
+&tmon {
+	pinctrl-0 = <&fan_pins>;
+	pinctrl-names = "default";
+};
+
+&usart0 {
+	pinctrl-0 = <&fc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb {
+	pinctrl-0 = <&usb_ulpi_pins>, <&usb_rst_pins>, <&usb_over_pins>, <&usb_power_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
-- 
2.52.0

Re: [PATCH v4 14/15] dt-bindings: arm: AT91: document EV23X71A board

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 52 bytes --]

Acked-by: Conor Dooley <conor.dooley@microchip.com>

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH v4 01/15] dt-bindings: usb: Add Microchip LAN969x support

[Rob Herring (Arm)]

On Mon, 29 Dec 2025 19:37:42 +0100, Robert Marko wrote:
> Microchip LAN969x has DWC3 compatible controller, though limited to 2.0(HS)
> speed, so document it.
> 
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> ---
> Changes in v2:
> * Fix example indentation
> 
>  .../bindings/usb/microchip,lan9691-dwc3.yaml  | 66 +++++++++++++++++++
>  1 file changed, 66 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/microchip,lan9691-dwc3.yaml
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v4 09/15] dt-bindings: dma: atmel: add microchip,lan9691-dma

[Rob Herring (Arm)]

On Mon, 29 Dec 2025 19:37:50 +0100, Robert Marko wrote:
> Document Microchip LAN969x DMA compatible which is compatible to SAMA7G5.
> 
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> ---
> Changes in v3:
> * Merged with microchip,sama7d65-dma since that also falls back to
> microchip,sama7g5-dma
> 
>  Documentation/devicetree/bindings/dma/atmel,sama5d4-dma.yaml | 4 +++-
>  1 file changed, 3 insertions(+), 1 deletion(-)
> 

Acked-by: Rob Herring (Arm) <robh@kernel.org>

Re: (subset) [PATCH v4 00/15] Add support for Microchip LAN969x

[Vinod Koul]

On Mon, 29 Dec 2025 19:37:41 +0100, Robert Marko wrote:
> This series adds support for the Microchip LAN969x switch SoC family.
> 
> Series is a bit long since after discussions in previous versions, it was
> recommended[1][2] to add SoC specific compatibles for device nodes so it
> includes the required bindings updates.
> 
> [1] https://lore.kernel.org/all/20251203-splendor-cubbyhole-eda2d6982b46@spud/
> [2] https://lore.kernel.org/all/173412c8-c2fb-4c38-8de7-5b1c2eebdbf9@microchip.com/
> [3] https://lore.kernel.org/all/20251203-duly-leotard-86b83bd840c6@spud/
> [4] https://lore.kernel.org/all/756ead5d-8c9b-480d-8ae5-71667575ab7c@kernel.org/
> 
> [...]

Applied, thanks!

[09/15] dt-bindings: dma: atmel: add microchip,lan9691-dma
        commit: c47422f4d0a26b25ff59709921eaaf8f916eec7d

Best regards,
-- 
~Vinod

Re: [PATCH v4 00/15] Add support for Microchip LAN969x

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (main)
by Jakub Kicinski <kuba@kernel.org>:

On Mon, 29 Dec 2025 19:37:41 +0100 you wrote:
> This series adds support for the Microchip LAN969x switch SoC family.
> 
> Series is a bit long since after discussions in previous versions, it was
> recommended[1][2] to add SoC specific compatibles for device nodes so it
> includes the required bindings updates.
> 
> [1] https://lore.kernel.org/all/20251203-splendor-cubbyhole-eda2d6982b46@spud/
> [2] https://lore.kernel.org/all/173412c8-c2fb-4c38-8de7-5b1c2eebdbf9@microchip.com/
> [3] https://lore.kernel.org/all/20251203-duly-leotard-86b83bd840c6@spud/
> [4] https://lore.kernel.org/all/756ead5d-8c9b-480d-8ae5-71667575ab7c@kernel.org/
> 
> [...]

Here is the summary with links:
  - [v4,01/15] dt-bindings: usb: Add Microchip LAN969x support
    (no matching commit)
  - [v4,02/15] dt-bindings: mfd: atmel,sama5d2-flexcom: add microchip,lan9691-flexcom
    (no matching commit)
  - [v4,03/15] dt-bindings: serial: atmel,at91-usart: add microchip,lan9691-usart
    (no matching commit)
  - [v4,04/15] dt-bindings: spi: at91: add microchip,lan9691-spi
    (no matching commit)
  - [v4,05/15] dt-bindings: i2c: atmel,at91sam: add microchip,lan9691-i2c
    (no matching commit)
  - [v4,06/15] dt-bindings: rng: atmel,at91-trng: add microchip,lan9691-trng
    (no matching commit)
  - [v4,07/15] dt-bindings: crypto: atmel,at91sam9g46-aes: add microchip,lan9691-aes
    (no matching commit)
  - [v4,08/15] dt-bindings: crypto: atmel,at91sam9g46-sha: add microchip,lan9691-sha
    (no matching commit)
  - [v4,09/15] dt-bindings: dma: atmel: add microchip,lan9691-dma
    (no matching commit)
  - [v4,10/15] dt-bindings: net: mscc-miim: add microchip,lan9691-miim
    https://git.kernel.org/netdev/net-next/c/c303e8b86d9d
  - [v4,11/15] dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x
    (no matching commit)
  - [v4,12/15] arm64: dts: microchip: add LAN969x clock header file
    (no matching commit)
  - [v4,13/15] arm64: dts: microchip: add LAN969x support
    (no matching commit)
  - [v4,14/15] dt-bindings: arm: AT91: document EV23X71A board
    (no matching commit)
  - [v4,15/15] arm64: dts: microchip: add EV23X71A board
    (no matching commit)

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html

Re: [PATCH v4 04/15] dt-bindings: spi: at91: add microchip,lan9691-spi

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 439 bytes --]

On Mon, Dec 29, 2025 at 07:37:45PM +0100, Robert Marko wrote:

> Document Microchip LAN969x SPI compatible.

Please submit patches using subject lines reflecting the style for the
subsystem, this makes it easier for people to identify relevant patches.
Look at what existing commits in the area you're changing are doing and
make sure your subject lines visually resemble what they're doing.
There's no need to resubmit to fix this alone.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: (subset) [PATCH v4 00/15] Add support for Microchip LAN969x

[Mark Brown]

On Mon, 29 Dec 2025 19:37:41 +0100, Robert Marko wrote:
> This series adds support for the Microchip LAN969x switch SoC family.
> 
> Series is a bit long since after discussions in previous versions, it was
> recommended[1][2] to add SoC specific compatibles for device nodes so it
> includes the required bindings updates.
> 
> [1] https://lore.kernel.org/all/20251203-splendor-cubbyhole-eda2d6982b46@spud/
> [2] https://lore.kernel.org/all/173412c8-c2fb-4c38-8de7-5b1c2eebdbf9@microchip.com/
> [3] https://lore.kernel.org/all/20251203-duly-leotard-86b83bd840c6@spud/
> [4] https://lore.kernel.org/all/756ead5d-8c9b-480d-8ae5-71667575ab7c@kernel.org/
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[04/15] dt-bindings: spi: at91: add microchip,lan9691-spi
        commit: 96d337436fe0921177a6090aeb5bb214753654fc

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark