[PATCH 3/3] ARM: mach-shmobile: lager: support GPIO switches

[laurent.pinchart@ideasonboard.com (Laurent Pinchart)]

Hi Magnus,

On Tuesday 14 May 2013 15:09:08 Magnus Damm wrote:
> On Tue, May 14, 2013 at 11:59 AM, Simon Horman <horms@verge.net.au> wrote:
> > On Tue, May 14, 2013 at 12:35:20AM +0200, Laurent Pinchart wrote:
> >> On Monday 13 May 2013 17:53:53 Simon Horman wrote:
> >> > The lager board has pins 1 - 4 of SW2 wired up to GPIO pins.
> >> > This patch allows access to those pins as KEYS 1 - 4 using
> >> > gpio-keys.
> >> > 
> >> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
> >> > 
> >> > ---
> >> > 
> >> > This patch has run time dependencies on
> >> > 1. "gpio-rcar: Add support for IRQ_TYPE_EDGE_BOTH"
> >> > 2. "ARM: shmobile: r8a7790: Configure R-Car GPIO for
> >> > IRQ_TYPE_EDGE_BOTH"
> >> > 
> >> > Without those dependencies satisfied the gpio-keys driver will
> >> > fail to be initialise itself. The boot should be otherwise successful
> >> > and the board otherwise functional.
> >> > ---
> >> > 
> >> >  arch/arm/mach-shmobile/board-lager.c | 22 ++++++++++++++++++++++
> >> >  1 file changed, 22 insertions(+)
> >> > 
> >> > diff --git a/arch/arm/mach-shmobile/board-lager.c
> >> > b/arch/arm/mach-shmobile/board-lager.c index 6a1ba38..4d1b42b 100644
> >> > --- a/arch/arm/mach-shmobile/board-lager.c
> >> > +++ b/arch/arm/mach-shmobile/board-lager.c
> >> > @@ -18,7 +18,10 @@
> >> > 
> >> >   * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 
> >> >   02110-1301
> >> > 
> >> > USA */
> >> > 
> >> > +#include <linux/gpio.h>
> >> > +#include <linux/gpio_keys.h>
> >> > 
> >> >  #include <linux/interrupt.h>
> >> > 
> >> > +#include <linux/input.h>
> >> 
> >> My dictionary lists input before interrupt :-)
> > 
> > Thanks, I will fix that.
> > 
> >> >  #include <linux/irqchip.h>
> >> >  #include <linux/kernel.h>
> >> >  #include <linux/leds.h>
> >> > 
> >> > @@ -52,6 +55,22 @@ static struct gpio_led_platform_data
> >> > lager_leds_pdata = { .num_leds   = ARRAY_SIZE(lager_leds),
> >> > 
> >> >  };
> >> > 
> >> > +/* GPIO KEY */
> >> > +#define GPIO_KEY(c, g, d, ...) \
> >> > +   { .code = c, .gpio = g, .desc = d, .active_low = 1 }
> >> > +
> >> > +static struct gpio_keys_button gpio_buttons[] = {
> >> > +   GPIO_KEY(KEY_4,         RCAR_GP_PIN(1, 28),     "SW2-pin4"),
> >> > +   GPIO_KEY(KEY_3,         RCAR_GP_PIN(1, 26),     "SW2-pin3"),
> >> > +   GPIO_KEY(KEY_2,         RCAR_GP_PIN(1, 24),     "SW2-pin2"),
> >> > +   GPIO_KEY(KEY_1,         RCAR_GP_PIN(1, 14),     "SW2-pin1"),
> >> > +};
> >> > +
> >> > +static struct gpio_keys_platform_data lager_keys_pdata = {
> >> > +   .buttons        = gpio_buttons,
> >> > +   .nbuttons       = ARRAY_SIZE(gpio_buttons),
> >> > +};
> >> > +
> >> 
> >> Could you please also update the lager dts file ?
> > 
> > I wonder if in that case we can remove the C code above.
> > And probably the C code for the GPIO leds too.
> > 
> > Magnus, could you clarify how you would like
> > C-code and DTS to look on the lager board?
> 
> I'd like C and DTS to coexist in parallel until we can ditch C fully.
> I believe there is a need for us to be able to back port the C code.
> For the future we want to use DTS.
> 
> To support DTS for Lager I think you should create a -reference DTS
> file for Lager where you put the DT version of your GPIO LED / switch
> code. At the time when we can configure the PFC via PINCTRL DT then I
> believe we should be able to replace most of the platform device code
> with DT versions.

I've sent an RFC for gpio-rcar DT bindings, and I'll send one for sh-pfc in 
the next few days. DT support for GPIO and PINCTRL should then hopefully be 
available very soon.

> At that we should hopefully be able to ditch all the C board code,

Will we also ditch non-reference board files ?

> or maybe we need to keep some around until we have the common clocks
> going...

What's the status of CCF support development in sh-mobile ?

-- 
Regards,

Laurent Pinchart