From mboxrd@z Thu Jan  1 00:00:00 1970
From: jernej.skrabec@siol.net (Jernej =?utf-8?B?xaBrcmFiZWM=?=)
Date: Thu, 01 Nov 2018 08:52:17 +0100
Subject: [PATCH] ARM: dtsi: sun8i-r40: add mali node
In-Reply-To: <20181101073833.2936-1-lothar.felten@gmail.com>
References: <20181101073833.2936-1-lothar.felten@gmail.com>
Message-ID: <1868657.3A2CuZcRV2@jernej-laptop>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Dne ?etrtek, 01. november 2018 ob 08:38:33 CET je Lothar Felten napisal(a):
> This patch adds a node for the mali 400 GPU of the R40/V40 SoC
> 
> Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
> ---
>  arch/arm/boot/dts/sun8i-r40.dtsi | 28 +++++++++++++++++++++++++++-
>  1 file changed, 27 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi
> b/arch/arm/boot/dts/sun8i-r40.dtsi index 6f4c9ca5a3ee..ddf765e931f3 100644
> --- a/arch/arm/boot/dts/sun8i-r40.dtsi
> +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
> @@ -542,6 +542,31 @@
> 
>  		};
> 
> +		mali: gpu at 1c40000 {
> +			compatible = "allwinner,sun7i-a20-mali", "arm,mali-400";
> +			reg = <0x01c40000 0x10000>;
> +			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "gp",
> +					  "gpmmu",
> +					  "pp0",
> +					  "ppmmu0",
> +					  "pp1",
> +					  "ppmmu1",
> +					  "pmu";
> +			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
> +			clock-names = "bus", "core";
> +			resets = <&ccu RST_BUS_GPU>;
> +
> +			assigned-clocks = <&ccu CLK_GPU>;
> +			assigned-clock-rates = <384000000>;

In previous e-mail I already stated that above 2 lines doesn't belong here. 
Driver is responsible for clock rate management.

> +		};
> +
>  		gmac: ethernet at 1c50000 {
>  			compatible = "allwinner,sun8i-r40-gmac";
>  			syscon = <&ccu>;
> @@ -813,7 +838,8 @@
>  		};
> 
>  		hdmi_phy: hdmi-phy at 1ef0000 {
> -			compatible = "allwinner,sun8i-r40-hdmi-phy";
> +			compatible = "allwinner,sun8i-r40-hdmi-phy",
> +				     "allwinner,sun50i-a64-hdmi-phy";

In previous e-mail I also stated that above changes are not related to GPU 
node and they are also not needed, since HDMI on R40 works without this.

>  			reg = <0x01ef0000 0x10000>;
>  			clocks = <&ccu CLK_BUS_HDMI1>, <&ccu CLK_HDMI_SLOW>,
>  				 <&ccu 7>, <&ccu 16>;

You cleary didn't read rules for patch submission. When you are sending new 
version of the patch, you have to state which version is it in subject line 
and write a changelog below "---" line.

Best regards,
Jernej