* [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support
@ 2013-11-27 8:27 Magnus Damm
2013-11-27 8:27 ` [PATCH 01/04] ARM: shmobile: r7s72100 GPIO and PINCTRL device nodes Magnus Damm
` (4 more replies)
0 siblings, 5 replies; 15+ messages in thread
From: Magnus Damm @ 2013-11-27 8:27 UTC (permalink / raw)
To: linux-arm-kernel
ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support
[PATCH 01/04] ARM: shmobile: r7s72100 GPIO and PINCTRL device nodes
[PATCH 02/04] ARM: shmobile: Genmai LED1 and LED2 support
[PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support
[PATCH 04/04] ARM: shmobile: Genmai SCIF2 PINCTRL configuration
Add various device nodes to the r7s72100 SoC and the Genmai board,
nothing special just basic support for LEDs and I2C-over-GPIO.
Patch 4/4 depends on the r7s72100 PINCTRL pin grouping, but 1-3
depends on the GPIO driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
---
Written against renesas.git tag renesas-devel-v3.13-rc1-20131125 and
[PATCH] pinctrl: sh-pfc: Initial r7s72100 support
[PATCH v3] gpio: Renesas RZ GPIO driver V3
The following patches are needed for 4/4:
[PATCH 00/03] pinctrl: sh-pfc: r7s72100 SCIF2 support
[PATCH 01/03] pinctrl: sh-pfc: r7s72100 SCIF2 port3 support
[PATCH 02/03] pinctrl: sh-pfc: r7s72100 SCIF2 macro conversion
[PATCH 03/03] pinctrl: sh-pfc: r7s72100 SCIF2 port4, 6 and 8 support
arch/arm/boot/dts/r7s72100-genmai-reference.dts | 41 +++++-
arch/arm/boot/dts/r7s72100.dtsi | 154 +++++++++++++++++++++++
2 files changed, 194 insertions(+), 1 deletion(-)
^ permalink raw reply [flat|nested] 15+ messages in thread* [PATCH 01/04] ARM: shmobile: r7s72100 GPIO and PINCTRL device nodes 2013-11-27 8:27 [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Magnus Damm @ 2013-11-27 8:27 ` Magnus Damm 2013-11-27 8:27 ` [PATCH 02/04] ARM: shmobile: Genmai LED1 and LED2 support Magnus Damm ` (3 subsequent siblings) 4 siblings, 0 replies; 15+ messages in thread From: Magnus Damm @ 2013-11-27 8:27 UTC (permalink / raw) To: linux-arm-kernel From: Magnus Damm <damm@opensource.se> Add support for r7s72100 PFC and GPIO device nodes port0 -> port11 and jtagport0. Signed-off-by: Magnus Damm <damm@opensource.se> --- arch/arm/boot/dts/r7s72100.dtsi | 154 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 154 insertions(+) --- 0001/arch/arm/boot/dts/r7s72100.dtsi +++ work/arch/arm/boot/dts/r7s72100.dtsi 2013-11-27 16:06:36.000000000 +0900 @@ -14,6 +14,22 @@ #address-cells = <1>; #size-cells = <1>; + aliases { + gpio0 = &port0; + gpio1 = &port1; + gpio2 = &port2; + gpio3 = &port3; + gpio4 = &port4; + gpio5 = &port5; + gpio6 = &port6; + gpio7 = &port7; + gpio8 = &port8; + gpio9 = &port9; + gpio10 = &port10; + gpio11 = &port11; + gpio12 = &jtagport0; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -33,4 +49,142 @@ reg = <0xe8201000 0x1000>, <0xe8202000 0x1000>; }; + + pfc: pfc at fcfe3300 { + compatible = "renesas,pfc-r7s72100"; + reg = <0xfcfe3300 0x400>, /* PM, PMC, PFC, PFCE */ + <0xfcfe3a00 0x100>, /* PFCAE */ + <0xfcfe7000 0x300>, /* PIBC, PBDC, PIPC */ + <0xfcfe7b40 0x04>, /* JPMC */ + <0xfcfe7b90 0x04>, /* JPMCSR */ + <0xfcfe7f00 0x04>; /* JPIBC */ + }; + + port0: gpio at fcfe3100 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3100 0x4>, /* PSR */ + <0xfcfe3200 0x2>, /* PPR */ + <0xfcfe3800 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 0 6>; + }; + + port1: gpio at fcfe3104 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3104 0x4>, /* PSR */ + <0xfcfe3204 0x2>, /* PPR */ + <0xfcfe3804 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 16 16>; + }; + + port2: gpio at fcfe3108 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3108 0x4>, /* PSR */ + <0xfcfe3208 0x2>, /* PPR */ + <0xfcfe3808 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 32 16>; + }; + + port3: gpio at fcfe310c { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe310c 0x4>, /* PSR */ + <0xfcfe320c 0x2>, /* PPR */ + <0xfcfe380c 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 48 16>; + }; + + port4: gpio at fcfe3110 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3110 0x4>, /* PSR */ + <0xfcfe3210 0x2>, /* PPR */ + <0xfcfe3810 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 64 16>; + }; + + port5: gpio at fcfe3114 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3114 0x4>, /* PSR */ + <0xfcfe3214 0x2>, /* PPR */ + <0xfcfe3814 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 80 11>; + }; + + port6: gpio at fcfe3118 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3118 0x4>, /* PSR */ + <0xfcfe3218 0x2>, /* PPR */ + <0xfcfe3818 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 96 16>; + }; + + port7: gpio at fcfe311c { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe311c 0x4>, /* PSR */ + <0xfcfe321c 0x2>, /* PPR */ + <0xfcfe381c 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 112 16>; + }; + + port8: gpio at fcfe3120 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3120 0x4>, /* PSR */ + <0xfcfe3220 0x2>, /* PPR */ + <0xfcfe3820 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 128 16>; + }; + + port9: gpio at fcfe3124 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3124 0x4>, /* PSR */ + <0xfcfe3224 0x2>, /* PPR */ + <0xfcfe3824 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 144 8>; + }; + + port10: gpio at fcfe3128 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe3128 0x4>, /* PSR */ + <0xfcfe3228 0x2>, /* PPR */ + <0xfcfe3828 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 160 16>; + }; + + port11: gpio at fcfe312c { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe312c 0x4>, /* PSR */ + <0xfcfe322c 0x2>, /* PPR */ + <0xfcfe382c 0x4>; /* PMSR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 176 16>; + }; + + jtagport0: gpio at fcfe7b20 { + compatible = "renesas,gpio-r7s72100", "renesas,gpio-rz"; + reg = <0xfcfe7b20 0x2>; /* JPPR */ + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pfc 0 192 2>; + }; }; ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 02/04] ARM: shmobile: Genmai LED1 and LED2 support 2013-11-27 8:27 [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Magnus Damm 2013-11-27 8:27 ` [PATCH 01/04] ARM: shmobile: r7s72100 GPIO and PINCTRL device nodes Magnus Damm @ 2013-11-27 8:27 ` Magnus Damm 2013-11-27 11:16 ` Laurent Pinchart 2013-11-27 8:28 ` [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support Magnus Damm ` (2 subsequent siblings) 4 siblings, 1 reply; 15+ messages in thread From: Magnus Damm @ 2013-11-27 8:27 UTC (permalink / raw) To: linux-arm-kernel From: Magnus Damm <damm@opensource.se> Add support for Genmai board LED1 and LED2 via gpio-leds. Signed-off-by: Magnus Damm <damm@opensource.se> --- arch/arm/boot/dts/r7s72100-genmai-reference.dts | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) --- 0001/arch/arm/boot/dts/r7s72100-genmai-reference.dts +++ work/arch/arm/boot/dts/r7s72100-genmai-reference.dts 2013-11-27 15:49:27.000000000 +0900 @@ -9,7 +9,8 @@ */ /dts-v1/; -/include/ "r7s72100.dtsi" +#include "r7s72100.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Genmai"; @@ -28,4 +29,14 @@ #address-cells = <1>; #size-cells = <1>; }; + + leds { + compatible = "gpio-leds"; + led1 { + gpios = <&port4 10 GPIO_ACTIVE_LOW>; + }; + led2 { + gpios = <&port4 11 GPIO_ACTIVE_LOW>; + }; + }; }; ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 02/04] ARM: shmobile: Genmai LED1 and LED2 support 2013-11-27 8:27 ` [PATCH 02/04] ARM: shmobile: Genmai LED1 and LED2 support Magnus Damm @ 2013-11-27 11:16 ` Laurent Pinchart 0 siblings, 0 replies; 15+ messages in thread From: Laurent Pinchart @ 2013-11-27 11:16 UTC (permalink / raw) To: linux-arm-kernel Hi Magnus, Thank you for the patch. On Wednesday 27 November 2013 17:27:55 Magnus Damm wrote: > From: Magnus Damm <damm@opensource.se> > > Add support for Genmai board LED1 and LED2 via gpio-leds. > > Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > --- > > arch/arm/boot/dts/r7s72100-genmai-reference.dts | 13 ++++++++++++- > 1 file changed, 12 insertions(+), 1 deletion(-) > > --- 0001/arch/arm/boot/dts/r7s72100-genmai-reference.dts > +++ work/arch/arm/boot/dts/r7s72100-genmai-reference.dts 2013-11-27 > 15:49:27.000000000 +0900 @@ -9,7 +9,8 @@ > */ > > /dts-v1/; > -/include/ "r7s72100.dtsi" > +#include "r7s72100.dtsi" > +#include <dt-bindings/gpio/gpio.h> > > / { > model = "Genmai"; > @@ -28,4 +29,14 @@ > #address-cells = <1>; > #size-cells = <1>; > }; > + > + leds { > + compatible = "gpio-leds"; > + led1 { > + gpios = <&port4 10 GPIO_ACTIVE_LOW>; > + }; > + led2 { > + gpios = <&port4 11 GPIO_ACTIVE_LOW>; > + }; > + }; > }; -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support 2013-11-27 8:27 [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Magnus Damm 2013-11-27 8:27 ` [PATCH 01/04] ARM: shmobile: r7s72100 GPIO and PINCTRL device nodes Magnus Damm 2013-11-27 8:27 ` [PATCH 02/04] ARM: shmobile: Genmai LED1 and LED2 support Magnus Damm @ 2013-11-27 8:28 ` Magnus Damm 2013-11-27 11:04 ` Wolfram Sang 2013-11-27 11:15 ` Laurent Pinchart 2013-11-27 8:28 ` [PATCH 04/04] ARM: shmobile: Genmai SCIF2 PINCTRL configuration Magnus Damm 2013-11-27 11:13 ` [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Laurent Pinchart 4 siblings, 2 replies; 15+ messages in thread From: Magnus Damm @ 2013-11-27 8:28 UTC (permalink / raw) To: linux-arm-kernel From: Magnus Damm <damm@opensource.se> Add support for the Genmai I2C bus hooked up to P1_5 and P1_4 using the i2c-gpio driver. On the bus sits a 24c128 EEPRROM. Signed-off-by: Magnus Damm <damm@opensource.se> --- arch/arm/boot/dts/r7s72100-genmai-reference.dts | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) --- 0008/arch/arm/boot/dts/r7s72100-genmai-reference.dts +++ work/arch/arm/boot/dts/r7s72100-genmai-reference.dts 2013-11-27 15:51:31.000000000 +0900 @@ -39,4 +39,22 @@ gpios = <&port4 11 GPIO_ACTIVE_LOW>; }; }; + + i2c at 0 { + compatible = "i2c-gpio"; + gpios = <&port1 5 GPIO_ACTIVE_HIGH /* sda */ + &port1 4 GPIO_ACTIVE_HIGH /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <5>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + + eeprom: 24c128 at 50 { + compatible = "at,24c128"; + reg = <0x50>; + }; + }; + }; ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support 2013-11-27 8:28 ` [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support Magnus Damm @ 2013-11-27 11:04 ` Wolfram Sang 2013-11-28 17:11 ` Sergei Shtylyov 2013-11-27 11:15 ` Laurent Pinchart 1 sibling, 1 reply; 15+ messages in thread From: Wolfram Sang @ 2013-11-27 11:04 UTC (permalink / raw) To: linux-arm-kernel > + #address-cells = <1>; > + #size-cells = <0>; > + > + eeprom: 24c128 at 50 { > + compatible = "at,24c128"; Minor nit: Should be a vendor name, not the name of the driver > + reg = <0x50>; > + }; > + }; > + > }; -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131127/0fa420d3/attachment.sig> ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support 2013-11-27 11:04 ` Wolfram Sang @ 2013-11-28 17:11 ` Sergei Shtylyov 2013-11-28 17:14 ` Laurent Pinchart 0 siblings, 1 reply; 15+ messages in thread From: Sergei Shtylyov @ 2013-11-28 17:11 UTC (permalink / raw) To: linux-arm-kernel Hello. On 27-11-2013 15:04, Wolfram Sang wrote: >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + eeprom: 24c128 at 50 { >> + compatible = "at,24c128"; > Minor nit: Should be a vendor name, not the name of the driver Moreover, the node should be named generically, like "flash at 50", not "24c128 at 50". WBR, Sergei ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support 2013-11-28 17:11 ` Sergei Shtylyov @ 2013-11-28 17:14 ` Laurent Pinchart 2013-11-28 18:13 ` Sergei Shtylyov 0 siblings, 1 reply; 15+ messages in thread From: Laurent Pinchart @ 2013-11-28 17:14 UTC (permalink / raw) To: linux-arm-kernel On Thursday 28 November 2013 21:11:48 Sergei Shtylyov wrote: > On 27-11-2013 15:04, Wolfram Sang wrote: > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + > >> + eeprom: 24c128 at 50 { > >> + compatible = "at,24c128"; > > > > Minor nit: Should be a vendor name, not the name of the driver > > Moreover, the node should be named generically, like "flash at 50", not > "24c128 at 50". Or, given that it's an eeprom, "eeprom at 50" ? :-) -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support 2013-11-28 17:14 ` Laurent Pinchart @ 2013-11-28 18:13 ` Sergei Shtylyov 0 siblings, 0 replies; 15+ messages in thread From: Sergei Shtylyov @ 2013-11-28 18:13 UTC (permalink / raw) To: linux-arm-kernel Hello. On 28-11-2013 21:14, Laurent Pinchart wrote: >>>> + #address-cells = <1>; >>>> + #size-cells = <0>; >>>> + >>>> + eeprom: 24c128 at 50 { >>>> + compatible = "at,24c128"; >>> Minor nit: Should be a vendor name, not the name of the driver >> Moreover, the node should be named generically, like "flash at 50", not >> "24c128 at 50". > Or, given that it's an eeprom, "eeprom at 50" ? :-) At least ePAPR spec. only has "flash". WBR, Sergei ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support 2013-11-27 8:28 ` [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support Magnus Damm 2013-11-27 11:04 ` Wolfram Sang @ 2013-11-27 11:15 ` Laurent Pinchart 2013-11-28 0:44 ` Magnus Damm 1 sibling, 1 reply; 15+ messages in thread From: Laurent Pinchart @ 2013-11-27 11:15 UTC (permalink / raw) To: linux-arm-kernel Hi Magnus, Thank you for the patch. On Wednesday 27 November 2013 17:28:05 Magnus Damm wrote: > From: Magnus Damm <damm@opensource.se> > > Add support for the Genmai I2C bus hooked up to P1_5 and P1_4 using > the i2c-gpio driver. On the bus sits a 24c128 EEPRROM. Is this a temporary workaround until we get a proper I2C controller driver, or is the EEPROM really hooked up to pins that are not wired to a hardware I2C controller ? > Signed-off-by: Magnus Damm <damm@opensource.se> > --- > > arch/arm/boot/dts/r7s72100-genmai-reference.dts | 18 ++++++++++++++++++ > 1 file changed, 18 insertions(+) > > --- 0008/arch/arm/boot/dts/r7s72100-genmai-reference.dts > +++ work/arch/arm/boot/dts/r7s72100-genmai-reference.dts 2013-11-27 > 15:51:31.000000000 +0900 @@ -39,4 +39,22 @@ > gpios = <&port4 11 GPIO_ACTIVE_LOW>; > }; > }; > + > + i2c at 0 { > + compatible = "i2c-gpio"; > + gpios = <&port1 5 GPIO_ACTIVE_HIGH /* sda */ > + &port1 4 GPIO_ACTIVE_HIGH /* scl */ > + >; > + i2c-gpio,sda-open-drain; > + i2c-gpio,scl-open-drain; > + i2c-gpio,delay-us = <5>; /* ~100 kHz */ > + #address-cells = <1>; > + #size-cells = <0>; > + > + eeprom: 24c128 at 50 { > + compatible = "at,24c128"; > + reg = <0x50>; > + }; > + }; > + > }; -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support 2013-11-27 11:15 ` Laurent Pinchart @ 2013-11-28 0:44 ` Magnus Damm 2013-11-28 0:46 ` Laurent Pinchart 0 siblings, 1 reply; 15+ messages in thread From: Magnus Damm @ 2013-11-28 0:44 UTC (permalink / raw) To: linux-arm-kernel Hi Laurent, On Wed, Nov 27, 2013 at 8:15 PM, Laurent Pinchart <laurent.pinchart@ideasonboard.com> wrote: > Hi Magnus, > > Thank you for the patch. > > On Wednesday 27 November 2013 17:28:05 Magnus Damm wrote: >> From: Magnus Damm <damm@opensource.se> >> >> Add support for the Genmai I2C bus hooked up to P1_5 and P1_4 using >> the i2c-gpio driver. On the bus sits a 24c128 EEPRROM. > > Is this a temporary workaround until we get a proper I2C controller driver, or > is the EEPROM really hooked up to pins that are not wired to a hardware I2C > controller ? This is a stop-gap solution until we have upstream driver support for the I2C master hardware. The pins used for the I2C bus can be configured in GPIO mode or a zillion other pin functions including SCL and SDA. Cheers, / magnus ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support 2013-11-28 0:44 ` Magnus Damm @ 2013-11-28 0:46 ` Laurent Pinchart 0 siblings, 0 replies; 15+ messages in thread From: Laurent Pinchart @ 2013-11-28 0:46 UTC (permalink / raw) To: linux-arm-kernel Hi Magnus, On Thursday 28 November 2013 09:44:31 Magnus Damm wrote: > On Wed, Nov 27, 2013 at 8:15 PM, Laurent Pinchart wrote: > > On Wednesday 27 November 2013 17:28:05 Magnus Damm wrote: > >> From: Magnus Damm <damm@opensource.se> > >> > >> Add support for the Genmai I2C bus hooked up to P1_5 and P1_4 using > >> the i2c-gpio driver. On the bus sits a 24c128 EEPRROM. > > > > Is this a temporary workaround until we get a proper I2C controller > > driver, or is the EEPROM really hooked up to pins that are not wired to a > > hardware I2C controller ? > > This is a stop-gap solution until we have upstream driver support for the > I2C master hardware. OK, no problem. Is there a timeline for that ? > The pins used for the I2C bus can be configured in GPIO mode or a zillion > other pin functions including SCL and SDA. -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 04/04] ARM: shmobile: Genmai SCIF2 PINCTRL configuration 2013-11-27 8:27 [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Magnus Damm ` (2 preceding siblings ...) 2013-11-27 8:28 ` [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support Magnus Damm @ 2013-11-27 8:28 ` Magnus Damm 2013-11-27 11:16 ` Laurent Pinchart 2013-11-27 11:13 ` [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Laurent Pinchart 4 siblings, 1 reply; 15+ messages in thread From: Magnus Damm @ 2013-11-27 8:28 UTC (permalink / raw) To: linux-arm-kernel From: Magnus Damm <damm@opensource.se> Configure the r7s72100 PINCTRL hardware and select pin function for the SCIF2 serial console. Signed-off-by: Magnus Damm <damm@opensource.se> --- arch/arm/boot/dts/r7s72100-genmai-reference.dts | 10 ++++++++++ 1 file changed, 10 insertions(+) --- 0009/arch/arm/boot/dts/r7s72100-genmai-reference.dts +++ work/arch/arm/boot/dts/r7s72100-genmai-reference.dts 2013-11-27 17:13:43.000000000 +0900 @@ -58,3 +58,13 @@ }; }; + +&pfc { + pinctrl-0 = <&scif2_pins>; + pinctrl-names = "default"; + + scif2_pins: serial2 { + renesas,groups = "scif2_txd_p3_0", "scif2_rxd_p3_2"; + renesas,function = "scif2"; + }; +}; ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 04/04] ARM: shmobile: Genmai SCIF2 PINCTRL configuration 2013-11-27 8:28 ` [PATCH 04/04] ARM: shmobile: Genmai SCIF2 PINCTRL configuration Magnus Damm @ 2013-11-27 11:16 ` Laurent Pinchart 0 siblings, 0 replies; 15+ messages in thread From: Laurent Pinchart @ 2013-11-27 11:16 UTC (permalink / raw) To: linux-arm-kernel Hi Magnus, Thank you for the patch. On Wednesday 27 November 2013 17:28:14 Magnus Damm wrote: > From: Magnus Damm <damm@opensource.se> > > Configure the r7s72100 PINCTRL hardware and select pin function > for the SCIF2 serial console. > > Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > --- > > arch/arm/boot/dts/r7s72100-genmai-reference.dts | 10 ++++++++++ > 1 file changed, 10 insertions(+) > > --- 0009/arch/arm/boot/dts/r7s72100-genmai-reference.dts > +++ work/arch/arm/boot/dts/r7s72100-genmai-reference.dts 2013-11-27 > 17:13:43.000000000 +0900 @@ -58,3 +58,13 @@ > }; > > }; > + > +&pfc { > + pinctrl-0 = <&scif2_pins>; > + pinctrl-names = "default"; > + > + scif2_pins: serial2 { > + renesas,groups = "scif2_txd_p3_0", "scif2_rxd_p3_2"; > + renesas,function = "scif2"; > + }; > +}; -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support 2013-11-27 8:27 [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Magnus Damm ` (3 preceding siblings ...) 2013-11-27 8:28 ` [PATCH 04/04] ARM: shmobile: Genmai SCIF2 PINCTRL configuration Magnus Damm @ 2013-11-27 11:13 ` Laurent Pinchart 4 siblings, 0 replies; 15+ messages in thread From: Laurent Pinchart @ 2013-11-27 11:13 UTC (permalink / raw) To: linux-arm-kernel Hi Magnus, Thank you for the patches. Looking at how the PFC and GPIO registers are interleaved I'll really need the datasheet to properly review this and the previous PFC and GPIO patches. On Wednesday 27 November 2013 17:27:36 Magnus Damm wrote: > ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support > > [PATCH 01/04] ARM: shmobile: r7s72100 GPIO and PINCTRL device nodes > [PATCH 02/04] ARM: shmobile: Genmai LED1 and LED2 support > [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support > [PATCH 04/04] ARM: shmobile: Genmai SCIF2 PINCTRL configuration > > Add various device nodes to the r7s72100 SoC and the Genmai board, > nothing special just basic support for LEDs and I2C-over-GPIO. > > Patch 4/4 depends on the r7s72100 PINCTRL pin grouping, but 1-3 > depends on the GPIO driver. > > Signed-off-by: Magnus Damm <damm@opensource.se> > --- > > Written against renesas.git tag renesas-devel-v3.13-rc1-20131125 and > [PATCH] pinctrl: sh-pfc: Initial r7s72100 support > [PATCH v3] gpio: Renesas RZ GPIO driver V3 > > The following patches are needed for 4/4: > [PATCH 00/03] pinctrl: sh-pfc: r7s72100 SCIF2 support > [PATCH 01/03] pinctrl: sh-pfc: r7s72100 SCIF2 port3 support > [PATCH 02/03] pinctrl: sh-pfc: r7s72100 SCIF2 macro conversion > [PATCH 03/03] pinctrl: sh-pfc: r7s72100 SCIF2 port4, 6 and 8 support > > arch/arm/boot/dts/r7s72100-genmai-reference.dts | 41 +++++- > arch/arm/boot/dts/r7s72100.dtsi | 154 > +++++++++++++++++++++++ 2 files changed, 194 insertions(+), 1 deletion(-) -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2013-11-28 18:13 UTC | newest] Thread overview: 15+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2013-11-27 8:27 [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Magnus Damm 2013-11-27 8:27 ` [PATCH 01/04] ARM: shmobile: r7s72100 GPIO and PINCTRL device nodes Magnus Damm 2013-11-27 8:27 ` [PATCH 02/04] ARM: shmobile: Genmai LED1 and LED2 support Magnus Damm 2013-11-27 11:16 ` Laurent Pinchart 2013-11-27 8:28 ` [PATCH 03/04] ARM: shmobile: Genmai I2C-over-GPIO support Magnus Damm 2013-11-27 11:04 ` Wolfram Sang 2013-11-28 17:11 ` Sergei Shtylyov 2013-11-28 17:14 ` Laurent Pinchart 2013-11-28 18:13 ` Sergei Shtylyov 2013-11-27 11:15 ` Laurent Pinchart 2013-11-28 0:44 ` Magnus Damm 2013-11-28 0:46 ` Laurent Pinchart 2013-11-27 8:28 ` [PATCH 04/04] ARM: shmobile: Genmai SCIF2 PINCTRL configuration Magnus Damm 2013-11-27 11:16 ` Laurent Pinchart 2013-11-27 11:13 ` [PATCH 00/04] ARM: shmobile: r7s72100 and Genmai GPIO / PINCTRL support Laurent Pinchart
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).