Re: [PATCH 04/25] clk: meson: a1: add the audio clock controller driver

[Jerome Brunet <jbrunet@baylibre.com>]

On Tue 19 Mar 2024 at 04:47, Jan Dakinevich <jan.dakinevich@salutedevices.com> wrote:

> Let's start from the end:
>
>> No - Looks to me you just have two clock controllers you are trying
> force into one.
>
>> Again, this shows 2 devices. The one related to your 'map0' should
> request AUD2_CLKID_AUDIOTOP as input and enable it right away.
>
> Most of fishy workarounds that you commented is caused the fact the mmio
> of this clock controller is divided into two parts. Compare it with
> axg-audio driver, things that was part of contigous memory region (like
> pdm) here are moved to second region. Is this enough to make a guess
> that these are two devices?

I see obsolutely no reason to think it is a single device nor to add all the quirks
you have the way you did. So yes, in that case, 2 zones, 2 devices.

>
> Concerning AUD2_CLKID_AUDIOTOP clock, as it turned out, it must be
> enabled before enabling of clocks from second region too. That is
> AUD2_CLKID_AUDIOTOP clock feeds both parts of this clock controller.
>

Yes. I understood the first time around and already commented on that.

>
> On 3/15/24 12:20, Jerome Brunet wrote:
>> 
>> On Fri 15 Mar 2024 at 02:21, Jan Dakinevich <jan.dakinevich@salutedevices.com> wrote:
>> 
>>> This controller provides clocks and reset functionality for audio
>>> peripherals on Amlogic A1 SoC family.
>>>
>>> The driver is almost identical to 'axg-audio', however it would be better
>>> to keep it separate due to following reasons:
>>>
>>>  - significant amount of bits has another definition. I will bring there
>>>    a mess of new defines with A1_ suffixes.
>>>
>>>  - registers of this controller are located in two separate regions. It
>>>    will give a lot of complications for 'axg-audio' to support this.
>>>
>>> Signed-off-by: Jan Dakinevich <jan.dakinevich@salutedevices.com>
>>> ---
>>>  drivers/clk/meson/Kconfig    |  13 +
>>>  drivers/clk/meson/Makefile   |   1 +
>>>  drivers/clk/meson/a1-audio.c | 556 +++++++++++++++++++++++++++++++++++
>>>  drivers/clk/meson/a1-audio.h |  58 ++++
>>>  4 files changed, 628 insertions(+)
>>>  create mode 100644 drivers/clk/meson/a1-audio.c
>>>  create mode 100644 drivers/clk/meson/a1-audio.h
>>>
>>> diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
>>> index d6a2fa5f7e88..80c4a18c83d2 100644
>>> --- a/drivers/clk/meson/Kconfig
>>> +++ b/drivers/clk/meson/Kconfig
>>> @@ -133,6 +133,19 @@ config COMMON_CLK_A1_PERIPHERALS
>>>  	  device, A1 SoC Family. Say Y if you want A1 Peripherals clock
>>>  	  controller to work.
>>>  
>>> +config COMMON_CLK_A1_AUDIO
>>> +	tristate "Amlogic A1 SoC Audio clock controller support"
>>> +	depends on ARM64
>>> +	select COMMON_CLK_MESON_REGMAP
>>> +	select COMMON_CLK_MESON_CLKC_UTILS
>>> +	select COMMON_CLK_MESON_PHASE
>>> +	select COMMON_CLK_MESON_SCLK_DIV
>>> +	select COMMON_CLK_MESON_AUDIO_RSTC
>>> +	help
>>> +	  Support for the Audio clock controller on Amlogic A113L based
>>> +	  device, A1 SoC Family. Say Y if you want A1 Audio clock controller
>>> +	  to work.
>>> +
>>>  config COMMON_CLK_G12A
>>>  	tristate "G12 and SM1 SoC clock controllers support"
>>>  	depends on ARM64
>>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>>> index 88d94921a4dc..4968fc7ad555 100644
>>> --- a/drivers/clk/meson/Makefile
>>> +++ b/drivers/clk/meson/Makefile
>>> @@ -20,6 +20,7 @@ obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
>>>  obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
>>>  obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
>>>  obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
>>> +obj-$(CONFIG_COMMON_CLK_A1_AUDIO) += a1-audio.o
>>>  obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o
>>>  obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o
>>>  obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o meson8-ddr.o
>>> diff --git a/drivers/clk/meson/a1-audio.c b/drivers/clk/meson/a1-audio.c
>>> new file mode 100644
>>> index 000000000000..6039116c93ba
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/a1-audio.c
>>> @@ -0,0 +1,556 @@
>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
>>> +/*
>>> + * Copyright (c) 2024, SaluteDevices. All Rights Reserved.
>>> + *
>>> + * Author: Jan Dakinevich <jan.dakinevich@salutedevices.com>
>>> + */
>>> +
>>> +#include <linux/clk.h>
>>> +#include <linux/clk-provider.h>
>>> +#include <linux/init.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/module.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/regmap.h>
>>> +#include <linux/reset.h>
>>> +#include <linux/reset-controller.h>
>>> +#include <linux/slab.h>
>>> +
>>> +#include "meson-clkc-utils.h"
>>> +#include "meson-audio-rstc.h"
>>> +#include "clk-regmap.h"
>>> +#include "clk-phase.h"
>>> +#include "sclk-div.h"
>>> +#include "a1-audio.h"
>>> +
>>> +#define AUDIO_PDATA(_name) \
>>> +	((const struct clk_parent_data[]) { { .hw = &(_name).hw } })
>> 
>> Not a fan - yet another level of macro.
>> 
>>> +
>>> +#define AUDIO_MUX(_name, _reg, _mask, _shift, _pdata)			\
>>> +static struct clk_regmap _name = {					\
>>> +	.map = AUDIO_REG_MAP(_reg),					\
>>> +	.data = &(struct clk_regmap_mux_data){				\
>>> +		.offset = AUDIO_REG_OFFSET(_reg),			\
>>> +		.mask = (_mask),					\
>>> +		.shift = (_shift),					\
>>> +	},								\
>>> +	.hw.init = &(struct clk_init_data) {				\
>>> +		.name = #_name,						\
>>> +		.ops = &clk_regmap_mux_ops,				\
>>> +		.parent_data = (_pdata),				\
>>> +		.num_parents = ARRAY_SIZE(_pdata),			\
>>> +		.flags = CLK_SET_RATE_PARENT,				\
>>> +	},								\
>>> +}
>>> +
>>> +#define AUDIO_DIV(_name, _reg, _shift, _width, _pdata)			\
>>> +static struct clk_regmap _name = {					\
>>> +	.map = AUDIO_REG_MAP(_reg),					\
>>> +	.data = &(struct clk_regmap_div_data){				\
>>> +		.offset = AUDIO_REG_OFFSET(_reg),			\
>>> +		.shift = (_shift),					\
>>> +		.width = (_width),					\
>>> +	},								\
>>> +	.hw.init = &(struct clk_init_data) {				\
>>> +		.name = #_name,						\
>>> +		.ops = &clk_regmap_divider_ops,				\
>>> +		.parent_data = (_pdata),				\
>>> +		.num_parents = 1,					\
>>> +		.flags = CLK_SET_RATE_PARENT,				\
>>> +	},								\
>>> +}
>>> +
>>> +#define AUDIO_GATE(_name, _reg, _bit, _pdata)				\
>>> +static struct clk_regmap _name = {					\
>>> +	.map = AUDIO_REG_MAP(_reg),					\
>>> +	.data = &(struct clk_regmap_gate_data){				\
>>> +		.offset = AUDIO_REG_OFFSET(_reg),			\
>>> +		.bit_idx = (_bit),					\
>>> +	},								\
>>> +	.hw.init = &(struct clk_init_data) {				\
>>> +		.name = #_name,						\
>>> +		.ops = &clk_regmap_gate_ops,				\
>>> +		.parent_data = (_pdata),				\
>>> +		.num_parents = 1,					\
>>> +		.flags = CLK_SET_RATE_PARENT,				\
>>> +	},								\
>>> +}
>>> +
>>> +#define AUDIO_SCLK_DIV(_name, _reg, _div_shift, _div_width,		\
>>> +	_hi_shift, _hi_width, _pdata, _set_rate_parent)			\
>>> +static struct clk_regmap _name = {					\
>>> +	.map = AUDIO_REG_MAP(_reg),					\
>>> +	.data = &(struct meson_sclk_div_data) {				\
>>> +		.div = {						\
>>> +			.reg_off = AUDIO_REG_OFFSET(_reg),		\
>>> +			.shift = (_div_shift),				\
>>> +			.width = (_div_width),				\
>>> +		},							\
>>> +		.hi = {							\
>>> +			.reg_off = AUDIO_REG_OFFSET(_reg),		\
>>> +			.shift = (_hi_shift),				\
>>> +			.width = (_hi_width),				\
>>> +		},							\
>>> +	},								\
>>> +	.hw.init = &(struct clk_init_data) {				\
>>> +		.name = #_name,						\
>>> +		.ops = &meson_sclk_div_ops,				\
>>> +		.parent_data = (_pdata),				\
>>> +		.num_parents = 1,					\
>>> +		.flags = (_set_rate_parent) ? CLK_SET_RATE_PARENT : 0,	\
>> 
>> Does not help readeability. Just pass the flag as axg-audio does.
>> 
>>> +	},								\
>>> +}
>>> +
>>> +#define AUDIO_TRIPHASE(_name, _reg, _width, _shift0, _shift1, _shift2,	\
>>> +	_pdata)								\
>>> +static struct clk_regmap _name = {					\
>>> +	.map = AUDIO_REG_MAP(_reg),					\
>>> +	.data = &(struct meson_clk_triphase_data) {			\
>>> +		.ph0 = {						\
>>> +			.reg_off = AUDIO_REG_OFFSET(_reg),		\
>>> +			.shift = (_shift0),				\
>>> +			.width = (_width),				\
>>> +		},							\
>>> +		.ph1 = {						\
>>> +			.reg_off = AUDIO_REG_OFFSET(_reg),		\
>>> +			.shift = (_shift1),				\
>>> +			.width = (_width),				\
>>> +		},							\
>>> +		.ph2 = {						\
>>> +			.reg_off = AUDIO_REG_OFFSET(_reg),		\
>>> +			.shift = (_shift2),				\
>>> +			.width = (_width),				\
>>> +		},							\
>>> +	},								\
>>> +	.hw.init = &(struct clk_init_data) {				\
>>> +		.name = #_name,						\
>>> +		.ops = &meson_clk_triphase_ops,				\
>>> +		.parent_data = (_pdata),				\
>>> +		.num_parents = 1,					\
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_DUTY_CYCLE_PARENT,	\
>>> +	},								\
>>> +}
>>> +
>>> +#define AUDIO_SCLK_WS(_name, _reg, _width, _shift_ph, _shift_ws,	\
>>> +	_pdata)								\
>>> +static struct clk_regmap _name = {					\
>>> +	.map = AUDIO_REG_MAP(_reg),					\
>>> +	.data = &(struct meson_sclk_ws_inv_data) {			\
>>> +		.ph = {							\
>>> +			.reg_off = AUDIO_REG_OFFSET(_reg),		\
>>> +			.shift = (_shift_ph),				\
>>> +			.width = (_width),				\
>>> +		},							\
>>> +		.ws = {							\
>>> +			.reg_off = AUDIO_REG_OFFSET(_reg),		\
>>> +			.shift = (_shift_ws),				\
>>> +			.width = (_width),				\
>>> +		},							\
>>> +	},								\
>>> +	.hw.init = &(struct clk_init_data) {				\
>>> +		.name = #_name,						\
>>> +		.ops = &meson_sclk_ws_inv_ops,				\
>>> +		.parent_data = (_pdata),				\
>>> +		.num_parents = 1,					\
>>> +		.flags = CLK_SET_RATE_PARENT | CLK_DUTY_CYCLE_PARENT,	\
>>> +	},								\
>>> +}
>> 
>> All the above does essentially the same things as the macro of
>> axg-audio, to some minor differences. Yet it is another set to maintain.
>> 
>
> Except one thing... Here I keep memory identifier to which this clock
> belongs:
>
>     .map = AUDIO_REG_MAP(_reg),	
>
> It is workaround, but ->map the only common field in clk_regmap that
> could be used for this purpose.
>
>
>> I'd much prefer if you put the axg-audio macro in a header a re-used
>> those. There would a single set to maintain. You may then specialize the
>>  included in the driver C file, to avoid redundant parameters
>> 
>> Rework axg-audio to use clk_parent_data if you must, but not in the same
>> series please.
>> 
>>> +
>>> +static const struct clk_parent_data a1_pclk_pdata[] = {
>>> +	{ .fw_name = "pclk", },
>>> +};
>>> +
>>> +AUDIO_GATE(audio_ddr_arb, AUDIO_CLK_GATE_EN0, 0, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_tdmin_a, AUDIO_CLK_GATE_EN0, 1, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_tdmin_b, AUDIO_CLK_GATE_EN0, 2, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_tdmin_lb, AUDIO_CLK_GATE_EN0, 3, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_loopback, AUDIO_CLK_GATE_EN0, 4, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_tdmout_a, AUDIO_CLK_GATE_EN0, 5, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_tdmout_b, AUDIO_CLK_GATE_EN0, 6, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_frddr_a, AUDIO_CLK_GATE_EN0, 7, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_frddr_b, AUDIO_CLK_GATE_EN0, 8, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_toddr_a, AUDIO_CLK_GATE_EN0, 9, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_toddr_b, AUDIO_CLK_GATE_EN0, 10, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_spdifin, AUDIO_CLK_GATE_EN0, 11, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_resample, AUDIO_CLK_GATE_EN0, 12, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_eqdrc, AUDIO_CLK_GATE_EN0, 13, a1_pclk_pdata);
>>> +AUDIO_GATE(audio_audiolocker, AUDIO_CLK_GATE_EN0, 14, a1_pclk_pdata);
>>               This is what I mean by redundant parameter ^
>> 
>
> Yep. I could define something like AUDIO_PCLK_GATE().
>
>>> +
>>> +AUDIO_GATE(audio2_ddr_arb, AUDIO2_CLK_GATE_EN0, 0, a1_pclk_pdata);
>>> +AUDIO_GATE(audio2_pdm, AUDIO2_CLK_GATE_EN0, 1, a1_pclk_pdata);
>>> +AUDIO_GATE(audio2_tdmin_vad, AUDIO2_CLK_GATE_EN0, 2, a1_pclk_pdata);
>>> +AUDIO_GATE(audio2_toddr_vad, AUDIO2_CLK_GATE_EN0, 3, a1_pclk_pdata);
>>> +AUDIO_GATE(audio2_vad, AUDIO2_CLK_GATE_EN0, 4, a1_pclk_pdata);
>>> +AUDIO_GATE(audio2_audiotop, AUDIO2_CLK_GATE_EN0, 7, a1_pclk_pdata);
>>> +
>>> +static const struct clk_parent_data a1_mst_pdata[] = {
>>> +	{ .fw_name = "dds_in" },
>>> +	{ .fw_name = "fclk_div2" },
>>> +	{ .fw_name = "fclk_div3" },
>>> +	{ .fw_name = "hifi_pll" },
>>> +	{ .fw_name = "xtal" },
>>> +};
>>> +
>>> +#define AUDIO_MST_MCLK(_name, _reg)					\
>>> +	AUDIO_MUX(_name##_mux, (_reg), 0x7, 24, a1_mst_pdata);		\
>>> +	AUDIO_DIV(_name##_div, (_reg), 0, 16,				\
>>> +		AUDIO_PDATA(_name##_mux));				\
>>> +	AUDIO_GATE(_name, (_reg), 31, AUDIO_PDATA(_name##_div))
>>> +
>>> +AUDIO_MST_MCLK(audio_mst_a_mclk, AUDIO_MCLK_A_CTRL);
>>> +AUDIO_MST_MCLK(audio_mst_b_mclk, AUDIO_MCLK_B_CTRL);
>>> +AUDIO_MST_MCLK(audio_mst_c_mclk, AUDIO_MCLK_C_CTRL);
>>> +AUDIO_MST_MCLK(audio_mst_d_mclk, AUDIO_MCLK_D_CTRL);
>>> +AUDIO_MST_MCLK(audio_spdifin_clk, AUDIO_CLK_SPDIFIN_CTRL);
>>> +AUDIO_MST_MCLK(audio_eqdrc_clk, AUDIO_CLK_EQDRC_CTRL);
>>> +
>>> +AUDIO_MUX(audio_resample_clk_mux, AUDIO_CLK_RESAMPLE_CTRL, 0xf, 24,
>>> +	a1_mst_pdata);
>>> +AUDIO_DIV(audio_resample_clk_div, AUDIO_CLK_RESAMPLE_CTRL, 0, 8,
>>> +	AUDIO_PDATA(audio_resample_clk_mux));
>>> +AUDIO_GATE(audio_resample_clk, AUDIO_CLK_RESAMPLE_CTRL, 31,
>>> +	AUDIO_PDATA(audio_resample_clk_div));
>>> +
>>> +AUDIO_MUX(audio_locker_in_clk_mux, AUDIO_CLK_LOCKER_CTRL, 0xf, 8,
>>> +	a1_mst_pdata);
>>> +AUDIO_DIV(audio_locker_in_clk_div, AUDIO_CLK_LOCKER_CTRL, 0, 8,
>>> +	AUDIO_PDATA(audio_locker_in_clk_mux));
>>> +AUDIO_GATE(audio_locker_in_clk, AUDIO_CLK_LOCKER_CTRL, 15,
>>> +	AUDIO_PDATA(audio_locker_in_clk_div));
>>> +
>>> +AUDIO_MUX(audio_locker_out_clk_mux, AUDIO_CLK_LOCKER_CTRL, 0xf, 24,
>>> +	a1_mst_pdata);
>>> +AUDIO_DIV(audio_locker_out_clk_div, AUDIO_CLK_LOCKER_CTRL, 16, 8,
>>> +	AUDIO_PDATA(audio_locker_out_clk_mux));
>>> +AUDIO_GATE(audio_locker_out_clk, AUDIO_CLK_LOCKER_CTRL, 31,
>>> +	AUDIO_PDATA(audio_locker_out_clk_div));
>>> +
>>> +AUDIO_MST_MCLK(audio2_vad_mclk, AUDIO2_MCLK_VAD_CTRL);
>>> +AUDIO_MST_MCLK(audio2_vad_clk, AUDIO2_CLK_VAD_CTRL);
>>> +AUDIO_MST_MCLK(audio2_pdm_dclk, AUDIO2_CLK_PDMIN_CTRL0);
>>> +AUDIO_MST_MCLK(audio2_pdm_sysclk, AUDIO2_CLK_PDMIN_CTRL1);
>>> +
>>> +#define AUDIO_MST_SCLK(_name, _reg0, _reg1, _pdata)			\
>>> +	AUDIO_GATE(_name##_pre_en, (_reg0), 31, (_pdata));		\
>>> +	AUDIO_SCLK_DIV(_name##_div, (_reg0), 20, 10, 0, 0,		\
>>> +		AUDIO_PDATA(_name##_pre_en), true);			\
>>> +	AUDIO_GATE(_name##_post_en, (_reg0), 30,			\
>>> +		AUDIO_PDATA(_name##_div));				\
>>> +	AUDIO_TRIPHASE(_name, (_reg1), 1, 0, 2, 4,			\
>>> +		AUDIO_PDATA(_name##_post_en))
>>> +
>> 
>> Again, I'm not a fan of this many levels of macro. I can live with it
>> but certainly don't want the burden of reviewing and maintaining for
>> clock driver. AXG / G12 and A1 are obviously closely related, so make it common.
>> 
>>> +#define AUDIO_MST_LRCLK(_name, _reg0, _reg1, _pdata)			\
>>> +	AUDIO_SCLK_DIV(_name##_div, (_reg0), 0, 10, 10, 10,		\
>>> +		(_pdata), false);					\
>>> +	AUDIO_TRIPHASE(_name, (_reg1), 1, 1, 3, 5,			\
>>> +		AUDIO_PDATA(_name##_div))
>>> +
>>> +AUDIO_MST_SCLK(audio_mst_a_sclk, AUDIO_MST_A_SCLK_CTRL0, AUDIO_MST_A_SCLK_CTRL1,
>>> +	AUDIO_PDATA(audio_mst_a_mclk));
>>> +AUDIO_MST_SCLK(audio_mst_b_sclk, AUDIO_MST_B_SCLK_CTRL0, AUDIO_MST_B_SCLK_CTRL1,
>>> +	AUDIO_PDATA(audio_mst_b_mclk));
>>> +AUDIO_MST_SCLK(audio_mst_c_sclk, AUDIO_MST_C_SCLK_CTRL0, AUDIO_MST_C_SCLK_CTRL1,
>>> +	AUDIO_PDATA(audio_mst_c_mclk));
>>> +AUDIO_MST_SCLK(audio_mst_d_sclk, AUDIO_MST_D_SCLK_CTRL0, AUDIO_MST_D_SCLK_CTRL1,
>>> +	AUDIO_PDATA(audio_mst_d_mclk));
>>> +
>>> +AUDIO_MST_LRCLK(audio_mst_a_lrclk, AUDIO_MST_A_SCLK_CTRL0, AUDIO_MST_A_SCLK_CTRL1,
>>> +	AUDIO_PDATA(audio_mst_a_sclk_post_en));
>>> +AUDIO_MST_LRCLK(audio_mst_b_lrclk, AUDIO_MST_B_SCLK_CTRL0, AUDIO_MST_B_SCLK_CTRL1,
>>> +	AUDIO_PDATA(audio_mst_b_sclk_post_en));
>>> +AUDIO_MST_LRCLK(audio_mst_c_lrclk, AUDIO_MST_C_SCLK_CTRL0, AUDIO_MST_C_SCLK_CTRL1,
>>> +	AUDIO_PDATA(audio_mst_c_sclk_post_en));
>>> +AUDIO_MST_LRCLK(audio_mst_d_lrclk, AUDIO_MST_D_SCLK_CTRL0, AUDIO_MST_D_SCLK_CTRL1,
>>> +	AUDIO_PDATA(audio_mst_d_sclk_post_en));
>>> +
>>> +static const struct clk_parent_data a1_mst_sclk_pdata[] = {
>>> +	{ .hw = &audio_mst_a_sclk.hw },
>>> +	{ .hw = &audio_mst_b_sclk.hw },
>>> +	{ .hw = &audio_mst_c_sclk.hw },
>>> +	{ .hw = &audio_mst_d_sclk.hw },
>>> +	{ .fw_name = "slv_sclk0" },
>>> +	{ .fw_name = "slv_sclk1" },
>>> +	{ .fw_name = "slv_sclk2" },
>>> +	{ .fw_name = "slv_sclk3" },
>>> +	{ .fw_name = "slv_sclk4" },
>>> +	{ .fw_name = "slv_sclk5" },
>>> +	{ .fw_name = "slv_sclk6" },
>>> +	{ .fw_name = "slv_sclk7" },
>>> +	{ .fw_name = "slv_sclk8" },
>>> +	{ .fw_name = "slv_sclk9" },
>>> +};
>>> +
>>> +static const struct clk_parent_data a1_mst_lrclk_pdata[] = {
>>> +	{ .hw = &audio_mst_a_lrclk.hw },
>>> +	{ .hw = &audio_mst_b_lrclk.hw },
>>> +	{ .hw = &audio_mst_c_lrclk.hw },
>>> +	{ .hw = &audio_mst_d_lrclk.hw },
>>> +	{ .fw_name = "slv_lrclk0" },
>>> +	{ .fw_name = "slv_lrclk1" },
>>> +	{ .fw_name = "slv_lrclk2" },
>>> +	{ .fw_name = "slv_lrclk3" },
>>> +	{ .fw_name = "slv_lrclk4" },
>>> +	{ .fw_name = "slv_lrclk5" },
>>> +	{ .fw_name = "slv_lrclk6" },
>>> +	{ .fw_name = "slv_lrclk7" },
>>> +	{ .fw_name = "slv_lrclk8" },
>>> +	{ .fw_name = "slv_lrclk9" },
>>> +};
>>> +
>>> +#define AUDIO_TDM_SCLK(_name, _reg)					\
>>> +	AUDIO_MUX(_name##_mux, (_reg), 0xf, 24, a1_mst_sclk_pdata);	\
>>> +	AUDIO_GATE(_name##_pre_en, (_reg), 31,				\
>>> +		AUDIO_PDATA(_name##_mux));				\
>>> +	AUDIO_GATE(_name##_post_en, (_reg), 30,				\
>>> +		AUDIO_PDATA(_name##_pre_en));				\
>>> +	AUDIO_SCLK_WS(_name, (_reg), 1, 29, 28,				\
>>> +		AUDIO_PDATA(_name##_post_en))
>>> +
>>> +#define AUDIO_TDM_LRCLK(_name, _reg)					\
>>> +	AUDIO_MUX(_name, (_reg), 0xf, 20, a1_mst_lrclk_pdata)
>>> +
>>> +AUDIO_TDM_SCLK(audio_tdmin_a_sclk, AUDIO_CLK_TDMIN_A_CTRL);
>>> +AUDIO_TDM_SCLK(audio_tdmin_b_sclk, AUDIO_CLK_TDMIN_B_CTRL);
>>> +AUDIO_TDM_SCLK(audio_tdmin_lb_sclk, AUDIO_CLK_TDMIN_LB_CTRL);
>>> +AUDIO_TDM_SCLK(audio_tdmout_a_sclk, AUDIO_CLK_TDMOUT_A_CTRL);
>>> +AUDIO_TDM_SCLK(audio_tdmout_b_sclk, AUDIO_CLK_TDMOUT_B_CTRL);
>>> +
>>> +AUDIO_TDM_LRCLK(audio_tdmin_a_lrclk, AUDIO_CLK_TDMIN_A_CTRL);
>>> +AUDIO_TDM_LRCLK(audio_tdmin_b_lrclk, AUDIO_CLK_TDMIN_B_CTRL);
>>> +AUDIO_TDM_LRCLK(audio_tdmin_lb_lrclk, AUDIO_CLK_TDMIN_LB_CTRL);
>>> +AUDIO_TDM_LRCLK(audio_tdmout_a_lrclk, AUDIO_CLK_TDMOUT_A_CTRL);
>>> +AUDIO_TDM_LRCLK(audio_tdmout_b_lrclk, AUDIO_CLK_TDMOUT_B_CTRL);
>>> +
>>> +static struct clk_hw *a1_audio_hw_clks[] = {
>>> +	[AUD_CLKID_DDR_ARB]		= &audio_ddr_arb.hw,
>>> +	[AUD_CLKID_TDMIN_A]		= &audio_tdmin_a.hw,
>>> +	[AUD_CLKID_TDMIN_B]		= &audio_tdmin_b.hw,
>>> +	[AUD_CLKID_TDMIN_LB]		= &audio_tdmin_lb.hw,
>>> +	[AUD_CLKID_LOOPBACK]		= &audio_loopback.hw,
>>> +	[AUD_CLKID_TDMOUT_A]		= &audio_tdmout_a.hw,
>>> +	[AUD_CLKID_TDMOUT_B]		= &audio_tdmout_b.hw,
>>> +	[AUD_CLKID_FRDDR_A]		= &audio_frddr_a.hw,
>>> +	[AUD_CLKID_FRDDR_B]		= &audio_frddr_b.hw,
>>> +	[AUD_CLKID_TODDR_A]		= &audio_toddr_a.hw,
>>> +	[AUD_CLKID_TODDR_B]		= &audio_toddr_b.hw,
>>> +	[AUD_CLKID_SPDIFIN]		= &audio_spdifin.hw,
>>> +	[AUD_CLKID_RESAMPLE]		= &audio_resample.hw,
>>> +	[AUD_CLKID_EQDRC]		= &audio_eqdrc.hw,
>>> +	[AUD_CLKID_LOCKER]		= &audio_audiolocker.hw,
>>> +	[AUD_CLKID_MST_A_MCLK_SEL]	= &audio_mst_a_mclk_mux.hw,
>>> +	[AUD_CLKID_MST_A_MCLK_DIV]	= &audio_mst_a_mclk_div.hw,
>>> +	[AUD_CLKID_MST_A_MCLK]		= &audio_mst_a_mclk.hw,
>>> +	[AUD_CLKID_MST_B_MCLK_SEL]	= &audio_mst_b_mclk_mux.hw,
>>> +	[AUD_CLKID_MST_B_MCLK_DIV]	= &audio_mst_b_mclk_div.hw,
>>> +	[AUD_CLKID_MST_B_MCLK]		= &audio_mst_b_mclk.hw,
>>> +	[AUD_CLKID_MST_C_MCLK_SEL]	= &audio_mst_c_mclk_mux.hw,
>>> +	[AUD_CLKID_MST_C_MCLK_DIV]	= &audio_mst_c_mclk_div.hw,
>>> +	[AUD_CLKID_MST_C_MCLK]		= &audio_mst_c_mclk.hw,
>>> +	[AUD_CLKID_MST_D_MCLK_SEL]	= &audio_mst_d_mclk_mux.hw,
>>> +	[AUD_CLKID_MST_D_MCLK_DIV]	= &audio_mst_d_mclk_div.hw,
>>> +	[AUD_CLKID_MST_D_MCLK]		= &audio_mst_d_mclk.hw,
>>> +	[AUD_CLKID_RESAMPLE_CLK_SEL]	= &audio_resample_clk_mux.hw,
>>> +	[AUD_CLKID_RESAMPLE_CLK_DIV]	= &audio_resample_clk_div.hw,
>>> +	[AUD_CLKID_RESAMPLE_CLK]	= &audio_resample_clk.hw,
>>> +	[AUD_CLKID_LOCKER_IN_CLK_SEL]	= &audio_locker_in_clk_mux.hw,
>>> +	[AUD_CLKID_LOCKER_IN_CLK_DIV]	= &audio_locker_in_clk_div.hw,
>>> +	[AUD_CLKID_LOCKER_IN_CLK]	= &audio_locker_in_clk.hw,
>>> +	[AUD_CLKID_LOCKER_OUT_CLK_SEL]	= &audio_locker_out_clk_mux.hw,
>>> +	[AUD_CLKID_LOCKER_OUT_CLK_DIV]	= &audio_locker_out_clk_div.hw,
>>> +	[AUD_CLKID_LOCKER_OUT_CLK]	= &audio_locker_out_clk.hw,
>>> +	[AUD_CLKID_SPDIFIN_CLK_SEL]	= &audio_spdifin_clk_mux.hw,
>>> +	[AUD_CLKID_SPDIFIN_CLK_DIV]	= &audio_spdifin_clk_div.hw,
>>> +	[AUD_CLKID_SPDIFIN_CLK]		= &audio_spdifin_clk.hw,
>>> +	[AUD_CLKID_EQDRC_CLK_SEL]	= &audio_eqdrc_clk_mux.hw,
>>> +	[AUD_CLKID_EQDRC_CLK_DIV]	= &audio_eqdrc_clk_div.hw,
>>> +	[AUD_CLKID_EQDRC_CLK]		= &audio_eqdrc_clk.hw,
>>> +	[AUD_CLKID_MST_A_SCLK_PRE_EN]	= &audio_mst_a_sclk_pre_en.hw,
>>> +	[AUD_CLKID_MST_A_SCLK_DIV]	= &audio_mst_a_sclk_div.hw,
>>> +	[AUD_CLKID_MST_A_SCLK_POST_EN]	= &audio_mst_a_sclk_post_en.hw,
>>> +	[AUD_CLKID_MST_A_SCLK]		= &audio_mst_a_sclk.hw,
>>> +	[AUD_CLKID_MST_B_SCLK_PRE_EN]	= &audio_mst_b_sclk_pre_en.hw,
>>> +	[AUD_CLKID_MST_B_SCLK_DIV]	= &audio_mst_b_sclk_div.hw,
>>> +	[AUD_CLKID_MST_B_SCLK_POST_EN]	= &audio_mst_b_sclk_post_en.hw,
>>> +	[AUD_CLKID_MST_B_SCLK]		= &audio_mst_b_sclk.hw,
>>> +	[AUD_CLKID_MST_C_SCLK_PRE_EN]	= &audio_mst_c_sclk_pre_en.hw,
>>> +	[AUD_CLKID_MST_C_SCLK_DIV]	= &audio_mst_c_sclk_div.hw,
>>> +	[AUD_CLKID_MST_C_SCLK_POST_EN]	= &audio_mst_c_sclk_post_en.hw,
>>> +	[AUD_CLKID_MST_C_SCLK]		= &audio_mst_c_sclk.hw,
>>> +	[AUD_CLKID_MST_D_SCLK_PRE_EN]	= &audio_mst_d_sclk_pre_en.hw,
>>> +	[AUD_CLKID_MST_D_SCLK_DIV]	= &audio_mst_d_sclk_div.hw,
>>> +	[AUD_CLKID_MST_D_SCLK_POST_EN]	= &audio_mst_d_sclk_post_en.hw,
>>> +	[AUD_CLKID_MST_D_SCLK]		= &audio_mst_d_sclk.hw,
>>> +	[AUD_CLKID_MST_A_LRCLK_DIV]	= &audio_mst_a_lrclk_div.hw,
>>> +	[AUD_CLKID_MST_A_LRCLK]		= &audio_mst_a_lrclk.hw,
>>> +	[AUD_CLKID_MST_B_LRCLK_DIV]	= &audio_mst_b_lrclk_div.hw,
>>> +	[AUD_CLKID_MST_B_LRCLK]		= &audio_mst_b_lrclk.hw,
>>> +	[AUD_CLKID_MST_C_LRCLK_DIV]	= &audio_mst_c_lrclk_div.hw,
>>> +	[AUD_CLKID_MST_C_LRCLK]		= &audio_mst_c_lrclk.hw,
>>> +	[AUD_CLKID_MST_D_LRCLK_DIV]	= &audio_mst_d_lrclk_div.hw,
>>> +	[AUD_CLKID_MST_D_LRCLK]		= &audio_mst_d_lrclk.hw,
>>> +	[AUD_CLKID_TDMIN_A_SCLK_SEL]	= &audio_tdmin_a_sclk_mux.hw,
>>> +	[AUD_CLKID_TDMIN_A_SCLK_PRE_EN]	= &audio_tdmin_a_sclk_pre_en.hw,
>>> +	[AUD_CLKID_TDMIN_A_SCLK_POST_EN] = &audio_tdmin_a_sclk_post_en.hw,
>>> +	[AUD_CLKID_TDMIN_A_SCLK]	= &audio_tdmin_a_sclk.hw,
>>> +	[AUD_CLKID_TDMIN_A_LRCLK]	= &audio_tdmin_a_lrclk.hw,
>>> +	[AUD_CLKID_TDMIN_B_SCLK_SEL]	= &audio_tdmin_b_sclk_mux.hw,
>>> +	[AUD_CLKID_TDMIN_B_SCLK_PRE_EN]	= &audio_tdmin_b_sclk_pre_en.hw,
>>> +	[AUD_CLKID_TDMIN_B_SCLK_POST_EN] = &audio_tdmin_b_sclk_post_en.hw,
>>> +	[AUD_CLKID_TDMIN_B_SCLK]	= &audio_tdmin_b_sclk.hw,
>>> +	[AUD_CLKID_TDMIN_B_LRCLK]	= &audio_tdmin_b_lrclk.hw,
>>> +	[AUD_CLKID_TDMIN_LB_SCLK_SEL]	= &audio_tdmin_lb_sclk_mux.hw,
>>> +	[AUD_CLKID_TDMIN_LB_SCLK_PRE_EN] = &audio_tdmin_lb_sclk_pre_en.hw,
>>> +	[AUD_CLKID_TDMIN_LB_SCLK_POST_EN] = &audio_tdmin_lb_sclk_post_en.hw,
>>> +	[AUD_CLKID_TDMIN_LB_SCLK]	= &audio_tdmin_lb_sclk.hw,
>>> +	[AUD_CLKID_TDMIN_LB_LRCLK]	= &audio_tdmin_lb_lrclk.hw,
>>> +	[AUD_CLKID_TDMOUT_A_SCLK_SEL]	= &audio_tdmout_a_sclk_mux.hw,
>>> +	[AUD_CLKID_TDMOUT_A_SCLK_PRE_EN] = &audio_tdmout_a_sclk_pre_en.hw,
>>> +	[AUD_CLKID_TDMOUT_A_SCLK_POST_EN] = &audio_tdmout_a_sclk_post_en.hw,
>>> +	[AUD_CLKID_TDMOUT_A_SCLK]	= &audio_tdmout_a_sclk.hw,
>>> +	[AUD_CLKID_TDMOUT_A_LRCLK]	= &audio_tdmout_a_lrclk.hw,
>>> +	[AUD_CLKID_TDMOUT_B_SCLK_SEL]	= &audio_tdmout_b_sclk_mux.hw,
>>> +	[AUD_CLKID_TDMOUT_B_SCLK_PRE_EN] = &audio_tdmout_b_sclk_pre_en.hw,
>>> +	[AUD_CLKID_TDMOUT_B_SCLK_POST_EN] = &audio_tdmout_b_sclk_post_en.hw,
>>> +	[AUD_CLKID_TDMOUT_B_SCLK]	= &audio_tdmout_b_sclk.hw,
>>> +	[AUD_CLKID_TDMOUT_B_LRCLK]	= &audio_tdmout_b_lrclk.hw,
>>> +
>>> +	[AUD2_CLKID_DDR_ARB]		= &audio2_ddr_arb.hw,
>>> +	[AUD2_CLKID_PDM]		= &audio2_pdm.hw,
>>> +	[AUD2_CLKID_TDMIN_VAD]		= &audio2_tdmin_vad.hw,
>>> +	[AUD2_CLKID_TODDR_VAD]		= &audio2_toddr_vad.hw,
>>> +	[AUD2_CLKID_VAD]		= &audio2_vad.hw,
>>> +	[AUD2_CLKID_AUDIOTOP]		= &audio2_audiotop.hw,
>>> +	[AUD2_CLKID_VAD_MCLK_SEL]	= &audio2_vad_mclk_mux.hw,
>>> +	[AUD2_CLKID_VAD_MCLK_DIV]	= &audio2_vad_mclk_div.hw,
>>> +	[AUD2_CLKID_VAD_MCLK]		= &audio2_vad_mclk.hw,
>>> +	[AUD2_CLKID_VAD_CLK_SEL]	= &audio2_vad_clk_mux.hw,
>>> +	[AUD2_CLKID_VAD_CLK_DIV]	= &audio2_vad_clk_div.hw,
>>> +	[AUD2_CLKID_VAD_CLK]		= &audio2_vad_clk.hw,
>>> +	[AUD2_CLKID_PDM_DCLK_SEL]	= &audio2_pdm_dclk_mux.hw,
>>> +	[AUD2_CLKID_PDM_DCLK_DIV]	= &audio2_pdm_dclk_div.hw,
>>> +	[AUD2_CLKID_PDM_DCLK]		= &audio2_pdm_dclk.hw,
>>> +	[AUD2_CLKID_PDM_SYSCLK_SEL]	= &audio2_pdm_sysclk_mux.hw,
>>> +	[AUD2_CLKID_PDM_SYSCLK_DIV]	= &audio2_pdm_sysclk_div.hw,
>>> +	[AUD2_CLKID_PDM_SYSCLK]		= &audio2_pdm_sysclk.hw,
>>> +};
>>> +
>>> +static struct meson_clk_hw_data a1_audio_clks = {
>>> +	.hws = a1_audio_hw_clks,
>>> +	.num = ARRAY_SIZE(a1_audio_hw_clks),
>>> +};
>>> +
>>> +static struct regmap *a1_audio_map(struct platform_device *pdev,
>>> +				   unsigned int index)
>>> +{
>>> +	char name[32];
>>> +	const struct regmap_config cfg = {
>>> +		.reg_bits = 32,
>>> +		.val_bits = 32,
>>> +		.reg_stride = 4,
>>> +		.name = name,
>> 
>> Not necessary
>> 
>
> This implementation uses two regmaps, and this field allow to avoid
> errors like this:
>
> [    0.145530] debugfs: Directory 'fe050000.audio-clock-controller' with
> parent 'regmap' already present!
>
>>> +	};
>>> +	void __iomem *base;
>>> +
>>> +	base = devm_platform_ioremap_resource(pdev, index);
>>> +	if (IS_ERR(base))
>>> +		return base;
>>> +
>>> +	scnprintf(name, sizeof(name), "%d", index);
>>> +	return devm_regmap_init_mmio(&pdev->dev, base, &cfg);
>>> +}
>> 
>> That is overengineered. Please keep it simple. Declare the regmap_config
>> as static const global, and do it like axg-audio please.
>> 
>
> This only reason why it is not "static const" because I need to set
> unique name for each regmap.
>
>>> +
>>> +static int a1_register_clk(struct platform_device *pdev,
>>> +			   struct regmap *map0, struct regmap *map1,
>>> +			   struct clk_hw *hw)
>>> +{
>>> +	struct clk_regmap *clk = container_of(hw, struct clk_regmap, hw);
>>> +
>>> +	if (!hw)
>>> +		return 0;
>>> +
>>> +	switch ((unsigned long)clk->map) {
>>> +	case AUDIO_RANGE_0:
>>> +		clk->map = map0;
>>> +		break;
>>> +	case AUDIO_RANGE_1:
>>> +		clk->map = map1;
>>> +		break;
>> 
>> ... fishy
>> 
>>> +	default:
>>> +		WARN_ON(1);
>>> +		return -EINVAL;
>>> +	}
>>> +
>>> +	return devm_clk_hw_register(&pdev->dev, hw);
>>> +}
>>> +
>>> +static int a1_audio_clkc_probe(struct platform_device *pdev)
>>> +{
>>> +	struct regmap *map0, *map1;
>>> +	struct clk *clk;
>>> +	unsigned int i;
>>> +	int ret;
>>> +
>>> +	clk = devm_clk_get_enabled(&pdev->dev, "pclk");
>>> +	if (WARN_ON(IS_ERR(clk)))
>>> +		return PTR_ERR(clk);
>>> +
>>> +	map0 = a1_audio_map(pdev, 0);
>>> +	if (IS_ERR(map0))
>>> +		return PTR_ERR(map0);
>>> +
>>> +	map1 = a1_audio_map(pdev, 1);
>>> +	if (IS_ERR(map1))
>>> +		return PTR_ERR(map1);
>> 
>> No - Looks to me you just have two clock controllers you are trying
>> force into one.
>> 
>
> See the begining.
>
>>> +
>>> +	/*
>>> +	 * Register and enable AUD2_CLKID_AUDIOTOP clock first. Unless
>>> +	 * it is enabled any read/write to 'map0' hangs the CPU.
>>> +	 */
>>> +
>>> +	ret = a1_register_clk(pdev, map0, map1,
>>> +			      a1_audio_clks.hws[AUD2_CLKID_AUDIOTOP]);
>>> +	if (ret)
>>> +		return ret;
>>> +
>>> +	ret = clk_prepare_enable(a1_audio_clks.hws[AUD2_CLKID_AUDIOTOP]->clk);
>>> +	if (ret)
>>> +		return ret;
>> 
>> Again, this shows 2 devices. The one related to your 'map0' should
>> request AUD2_CLKID_AUDIOTOP as input and enable it right away.
>> 
>
> See the begining.
>
>>> +
>>> +	for (i = 0; i < a1_audio_clks.num; i++) {
>>> +		if (i == AUD2_CLKID_AUDIOTOP)
>>> +			continue;
>>> +
>>> +		ret = a1_register_clk(pdev, map0, map1, a1_audio_clks.hws[i]);
>>> +		if (ret)
>>> +			return ret;
>>> +	}
>>> +
>>> +	ret = devm_of_clk_add_hw_provider(&pdev->dev, meson_clk_hw_get,
>>> +					  &a1_audio_clks);
>>> +	if (ret)
>>> +		return ret;
>>> +
>>> +	BUILD_BUG_ON((unsigned long)AUDIO_REG_MAP(AUDIO_SW_RESET0) !=
>>> +		     AUDIO_RANGE_0);
>> 
>> Why is that necessary ?
>> 
>
> A little paranoia. Here AUDIO_SW_RESET0 is handled as map0's register,
> and I want to assert it.
>
>>> +	return meson_audio_rstc_register(&pdev->dev, map0,
>>> +					 AUDIO_REG_OFFSET(AUDIO_SW_RESET0), 32);
>>> +}
>>> +
>>> +static const struct of_device_id a1_audio_clkc_match_table[] = {
>>> +	{ .compatible = "amlogic,a1-audio-clkc", },
>>> +	{}
>>> +};
>>> +MODULE_DEVICE_TABLE(of, a1_audio_clkc_match_table);
>>> +
>>> +static struct platform_driver a1_audio_clkc_driver = {
>>> +	.probe = a1_audio_clkc_probe,
>>> +	.driver = {
>>> +		.name = "a1-audio-clkc",
>>> +		.of_match_table = a1_audio_clkc_match_table,
>>> +	},
>>> +};
>>> +module_platform_driver(a1_audio_clkc_driver);
>>> +
>>> +MODULE_DESCRIPTION("Amlogic A1 Audio Clock driver");
>>> +MODULE_AUTHOR("Jan Dakinevich <jan.dakinevich@salutedevices.com>");
>>> +MODULE_LICENSE("GPL");
>>> diff --git a/drivers/clk/meson/a1-audio.h b/drivers/clk/meson/a1-audio.h
>>> new file mode 100644
>>> index 000000000000..f994e87276cd
>>> --- /dev/null
>>> +++ b/drivers/clk/meson/a1-audio.h
>>> @@ -0,0 +1,58 @@
>>> +/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
>>> +/*
>>> + * Copyright (c) 2024, SaluteDevices. All Rights Reserved.
>>> + *
>>> + * Author: Jan Dakinevich <jan.dakinevich@salutedevices.com>
>>> + */
>>> +
>>> +#ifndef __A1_AUDIO_H
>>> +#define __A1_AUDIO_H
>>> +
>>> +#define AUDIO_RANGE_0		0xa
>>> +#define AUDIO_RANGE_1		0xb
>>> +#define AUDIO_RANGE_SHIFT	16
>>> +
>>> +#define AUDIO_REG(_range, _offset) \
>>> +	(((_range) << AUDIO_RANGE_SHIFT) + (_offset))
>>> +
>>> +#define AUDIO_REG_OFFSET(_reg) \
>>> +	((_reg) & ((1 << AUDIO_RANGE_SHIFT) - 1))
>>> +
>>> +#define AUDIO_REG_MAP(_reg) \
>>> +	((void *)((_reg) >> AUDIO_RANGE_SHIFT))
>> 
>> That is seriouly overengineered.
>> The following are offset. Just write what they are.
>> 
>
> This is all in order to keep range's identifier together with offset and
> then use it to store the identifier in clk_regmaps.
>
>> There is not reason to put that into a header. It is only going to be
>> used by a single driver.
>> >> +
>>> +#define AUDIO_CLK_GATE_EN0	AUDIO_REG(AUDIO_RANGE_0, 0x000)
>>> +#define AUDIO_MCLK_A_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x008)
>>> +#define AUDIO_MCLK_B_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x00c)
>>> +#define AUDIO_MCLK_C_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x010)
>>> +#define AUDIO_MCLK_D_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x014)
>>> +#define AUDIO_MCLK_E_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x018)
>>> +#define AUDIO_MCLK_F_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x01c)
>>> +#define AUDIO_SW_RESET0		AUDIO_REG(AUDIO_RANGE_0, 0x028)
>>> +#define AUDIO_MST_A_SCLK_CTRL0	AUDIO_REG(AUDIO_RANGE_0, 0x040)
>>> +#define AUDIO_MST_A_SCLK_CTRL1	AUDIO_REG(AUDIO_RANGE_0, 0x044)
>>> +#define AUDIO_MST_B_SCLK_CTRL0	AUDIO_REG(AUDIO_RANGE_0, 0x048)
>>> +#define AUDIO_MST_B_SCLK_CTRL1	AUDIO_REG(AUDIO_RANGE_0, 0x04c)
>>> +#define AUDIO_MST_C_SCLK_CTRL0	AUDIO_REG(AUDIO_RANGE_0, 0x050)
>>> +#define AUDIO_MST_C_SCLK_CTRL1	AUDIO_REG(AUDIO_RANGE_0, 0x054)
>>> +#define AUDIO_MST_D_SCLK_CTRL0	AUDIO_REG(AUDIO_RANGE_0, 0x058)
>>> +#define AUDIO_MST_D_SCLK_CTRL1	AUDIO_REG(AUDIO_RANGE_0, 0x05c)
>>> +#define AUDIO_CLK_TDMIN_A_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x080)
>>> +#define AUDIO_CLK_TDMIN_B_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x084)
>>> +#define AUDIO_CLK_TDMIN_LB_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x08c)
>>> +#define AUDIO_CLK_TDMOUT_A_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x090)
>>> +#define AUDIO_CLK_TDMOUT_B_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x094)
>>> +#define AUDIO_CLK_SPDIFIN_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x09c)
>>> +#define AUDIO_CLK_RESAMPLE_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x0a4)
>>> +#define AUDIO_CLK_LOCKER_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x0a8)
>>> +#define AUDIO_CLK_EQDRC_CTRL	AUDIO_REG(AUDIO_RANGE_0, 0x0c0)
>>> +
>>> +#define AUDIO2_CLK_GATE_EN0	AUDIO_REG(AUDIO_RANGE_1, 0x00c)
>>> +#define AUDIO2_MCLK_VAD_CTRL	AUDIO_REG(AUDIO_RANGE_1, 0x040)
>>> +#define AUDIO2_CLK_VAD_CTRL	AUDIO_REG(AUDIO_RANGE_1, 0x044)
>>> +#define AUDIO2_CLK_PDMIN_CTRL0	AUDIO_REG(AUDIO_RANGE_1, 0x058)
>>> +#define AUDIO2_CLK_PDMIN_CTRL1	AUDIO_REG(AUDIO_RANGE_1, 0x05c)
>>> +
>>> +#include <dt-bindings/clock/amlogic,a1-audio-clkc.h>
>>> +
>>> +#endif /* __A1_AUDIO_H */
>> 
>> 


-- 
Jerome

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel