From mboxrd@z Thu Jan 1 00:00:00 1970 From: dk-arm-linux@gmx.de (Dieter Kiermaier) Date: Thu, 29 Oct 2009 11:36:50 +0200 Subject: marvell kirkwood / openrd-base kernel freeze on bootup with PICe->PCI bridge In-Reply-To: <200910291014.05981.dk-arm-linux@gmx.de> References: <200910290936.40397.dk-arm-linux@gmx.de> <20091029085236.GN14091@buzzloop.caiaq.de> <200910291014.05981.dk-arm-linux@gmx.de> Message-ID: <200910291036.51048.dk-arm-linux@gmx.de> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Maybe helpful additional information: It makes no difference if I connect a PCI device behind my bridge or not. The trace is exactly the same. Dieter > Am Donnerstag 29 Oktober 2009 09:52:36 schrieb Daniel Mack: > Hi Daniel, > > > > On Thu, Oct 29, 2009 at 10:36:40AM +0200, Dieter Kiermaier wrote: > > > ## Booting kernel from Legacy Image at 00800000 ... > > > Image Name: Linux-2.6.32-rc5-00081-g964fe08- > > > Image Type: ARM Linux Kernel Image (uncompressed) > > > Data Size: 2390056 Bytes = 2.3 MB > > > Load Address: 00008000 > > > Entry Point: 00008000 > > > Verifying Checksum ... OK > > > Loading Kernel Image ... OK > > > OK > > > > > > Starting kernel ... > > > > > > Uncompressing Linux............................................................................................................................................................ done. > > > > The problem most probably is that your kernel dies before the console is > > enabled, and hence you're not pointed to the actual problem. > > > > Try the patch below - printk() messages are not buffered but sent out > > directly to the lowlevel UART functions with this hack. CONFIG_DEBUG_LL > > must be enabled for this. > > I think your patch leads us to the root but I fear I don't know about PCI / Kernel programming to fix it :( > Here is my start log: > > Hopefully someone can see what is going wrong? > > Starting kernel ... > > Uncompressing Linux............................................................................................................................................................ done. > <5>Linux version 2.6.32-rc5-00081-g964fe08-dirty (dieter at dk1-linux) (gcc version 4.2.0 20070413 (prerelease)) #7 PREEMPT Thu Oct 29 10:05:02 CET 2009 > CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177 > CPU: VIVT data cache, VIVT instruction cache > Machine: Marvell OpenRD Base Board > Memory policy: ECC disabled, Data cache writeback > <7>On node 0 totalpages: 131072 > <7>free_area_init_node: node 0, pgdat c04c5dec, node_mem_map c058d000 > <7> Normal zone: 1024 pages used for memmap > <7> Normal zone: 0 pages reserved > <7> Normal zone: 130048 pages, LIFO batch:31 > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 > <5>Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x400000 at 0x100000(uImage),0x1fb00000 at 0x500000(rootfs) rw root=/dev/nfs rw nfsroot=192.168.2.251:/home/dieter/ArtistaNt > <6>PID hash table entries: 2048 (order: 1, 8192 bytes) > <6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > <6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > <6>Memory: 256MB 256MB = 512MB total > <5>Memory: 513920KB available (4420K code, 961K data, 120K init, 0K highmem) > <6>SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 > <6>Hierarchical RCU implementation. > <6>NR_IRQS:114 > Console: colour dummy device 80x30 > <6>Calibrating delay loop... 1199.30 BogoMIPS (lpj=5996544) > Mount-cache hash table entries: 512 > <6>CPU: Testing write buffer coherency: ok > <6>NET: Registered protocol family 16 > <6>Kirkwood: MV88F6281-A0, TCLK=200000000. > <6>Feroceon L2: Cache support initialised. > <7>initial MPP regs: 01111111 11113311 33331111 33103333 42222033 22244444 00000022 > <7> final MPP regs: 01111111 11113311 33331111 33003333 42222033 22244444 00000022 > <7>PCI: Scanning bus 0000:00 > <7>pci 0000:00:00.0: found [11ab:6281] class 000580 header type 00 > <7>pci 0000:00:00.0: reg 10 64bit mmio pref: [0xd0000000-0xd00fffff] > <7>pci 0000:00:00.0: reg 18 32bit mmio: [0x000000-0x1fffffff] > <7>pci 0000:00:00.0: calling pci_fixup_ide_bases+0x0/0x44 > <7>pci 0000:00:00.0: calling rc_pci_fixup+0x0/0x40 > <7>pci 0000:00:00.0: calling quirk_resource_alignment+0x0/0x19c > <7>pci 0000:00:00.0: supports D1 D2 > <7>pci 0000:00:01.0: found [11ab:2211] class 000604 header type 01 > <7>pci 0000:00:01.0: calling pci_fixup_ide_bases+0x0/0x44 > <7>pci 0000:00:01.0: calling rc_pci_fixup+0x0/0x40 > <7>pci 0000:00:01.0: calling quirk_resource_alignment+0x0/0x19c > <7>pci 0000:00:01.0: supports D1 D2 > <6>pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold > <6>pci 0000:00:01.0: PME# disabled > <7>PCI: Fixups for bus 0000:00 > <6>PCI: bus0: Fast back to back transfers disabled > <7>pci 0000:00:01.0: scanning behind bridge, config 000000, pass 0 > <7>pci 0000:00:01.0: bus configuration invalid, reconfiguring > <7>pci 0000:00:01.0: scanning behind bridge, config 000000, pass 1 > <7>PCI: Scanning bus 0000:01 > <1>Unhandled fault: external abort on non-linefetch (0x028) at 0xfee418fc > <0>Internal error: : 28 [#1] PREEMPT > <0>last sysfs file: > Modules linked in: > CPU: 0 Not tainted (2.6.32-rc5-00081-g964fe08-dirty #7) > PC is at orion_pcie_rd_conf+0x48/0x98 > LR is at 0x0 > pc : [] lr : [<00000000>] psr: 20000093 > sp : df835e58 ip : 00000004 fp : 00000000 > r10: df835e94 r9 : 00000000 r8 : 00000000 > r7 : 00000000 r6 : 00000004 r5 : df81b800 r4 : 00000000 > r3 : 000018fc r2 : 00000000 r1 : 80010000 r0 : fee40000 > Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel > Control: 0005317f Table: 00004000 DAC: 00000017 > <0>Process swapper (pid: 1, stack limit = 0xdf834270) > <0>Stack: (0xdf835e58 to 0xdf836000) > <0>5e40: 20000093 c002f944 > <0>5e60: 00000004 df835e94 0000000f 60000013 df81b800 df835eb4 df81b800 00000000 > <0>5e80: 00000000 c01c1e90 df835e94 00000000 00000000 00000000 df835eb4 00000000 > <0>5ea0: df81b800 c036c7e0 c049f634 df81b800 00000000 00000001 df81b800 00000008 > <0>5ec0: 00000000 df81b800 df81b600 00000000 00000000 c01c3d74 60000013 df81b800 > <0>5ee0: 00000008 00000001 00000001 c036ded8 df830800 df81b800 00000000 00000001 > <0>5f00: df81b600 c036dd48 00000001 00000000 c040abbc c040abbc 00ff0100 00219f00 > <0>5f20: 00000000 df81b600 df830800 00000000 00000001 df81b614 00000000 c04c9f00 > <0>5f40: 00000000 c036df48 df81b600 00000001 c0022198 df834000 00000040 c036dfa8 > <0>5f60: df807b00 c000c638 df807b00 c000a3ac c0009a4c c01f0e94 df8007c0 c00205e0 > <0>5f80: c00209bc 00000000 00000000 00000000 00000000 c04c9f00 c000cbfc c000cc1c > <0>5fa0: c001a7c8 c00263b8 df835fb6 c006f770 df809ae0 00000001 00000033 00000000 > <0>5fc0: 00000000 c00205e0 c00209bc 00000000 00000000 00000000 00000000 00000000 > <0>5fe0: 00000000 c000888c 00000000 00000000 00000000 c00273dc ffff0000 ffff0000 > [] (orion_pcie_rd_conf+0x48/0x98) from [] (pcie_rd_conf+0x7c/0xb8) > [] (pcie_rd_conf+0x7c/0xb8) from [] (pci_bus_read_config_dword+0x58/0x98) > [] (pci_bus_read_config_dword+0x58/0x98) from [] (pci_scan_single_device+0x3c/0x150) > [] (pci_scan_single_device+0x3c/0x150) from [] (pci_scan_slot+0x14/0x7c) > [] (pci_scan_slot+0x14/0x7c) from [] (pci_scan_child_bus+0x30/0xec) > [] (pci_scan_child_bus+0x30/0xec) from [] (pci_scan_bridge+0x1a8/0x308) > [] (pci_scan_bridge+0x1a8/0x308) from [] (pci_scan_child_bus+0xa0/0xec) > [] (pci_scan_child_bus+0xa0/0xec) from [] (pci_scan_bus_parented+0x14/0x20) > [] (pci_scan_bus_parented+0x14/0x20) from [] (kirkwood_pcie_scan_bus+0x1c/0x48) > [] (kirkwood_pcie_scan_bus+0x1c/0x48) from [] (pci_common_init+0x120/0x20c) > [] (pci_common_init+0x120/0x20c) from [] (openrd_base_pci_init+0x20/0x34) > [] (openrd_base_pci_init+0x20/0x34) from [] (do_one_initcall+0x58/0x1a4) > [] (do_one_initcall+0x58/0x1a4) from [] (kernel_init+0x90/0x104) > [] (kernel_init+0x90/0x104) from [] (kernel_thread_exit+0x0/0x8) > <0>Code: e59f3054 e7801003 e2833004 e59dc008 (e7902003) > <4>---[ end trace 1b75b31a2719ed1c ]--- > <6>note: swapper[1] exited with preempt_count 3 > <0>Kernel panic - not syncing: Attempted to kill init! > [] (unwind_backtrace+0x0/0xd8) from [] (panic+0x58/0x12c) > [] (panic+0x58/0x12c) from [] (do_exit+0x64/0x6d0) > [] (do_exit+0x64/0x6d0) from [] (die+0x174/0x198) > [] (die+0x174/0x198) from [] (dump_stack+0x0/0xc) > > > > > > > Daniel > > > > > > diff --git a/kernel/printk.c b/kernel/printk.c > > index b4d97b5..7919751 100644 > > --- a/kernel/printk.c > > +++ b/kernel/printk.c > > @@ -686,6 +686,7 @@ asmlinkage int vprintk(const char *fmt, va_list args) > > printed_len += vscnprintf(printk_buf + printed_len, > > sizeof(printk_buf) - printed_len, fmt, args); > > > > +{ extern void printascii(const char *); printascii(printk_buf); } > > > > p = printk_buf; > > > > > > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel at lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel >