From: marek.vasut@gmail.com (Marek Vasut)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/3] ARM: pxa/raumfeld: add platform support
Date: Thu, 26 Nov 2009 20:13:47 +0100 [thread overview]
Message-ID: <200911262013.47713.marek.vasut@gmail.com> (raw)
In-Reply-To: <1259258341-31114-2-git-send-email-daniel@caiaq.de>
Dne ?t 26. listopadu 2009 18:58:59 Daniel Mack napsal(a):
> This adds support for Raumfeld's 'Controller', 'Connector', 'Speaker S'
> and 'Speaker M' devices. They're all based on PXA303 SoCs.
>
> Signed-off-by: Daniel Mack <daniel@caiaq.de>
> ---
...
> +/*
> + * GPIO configurations
> + */
> +static mfp_cfg_t __raumfeld_controller_pin_config[] = {
> + /* UART1 */
> + GPIO77_UART1_RXD,
> + GPIO78_UART1_TXD,
> + GPIO79_UART1_CTS,
> + GPIO81_UART1_DSR,
> + GPIO83_UART1_DTR,
> + GPIO84_UART1_RTS,
> +
> + /* UART3 */
> + GPIO110_UART3_RXD,
> +
> + /* USB Host */
> + GPIO0_2_USBH_PEN,
> + GPIO1_2_USBH_PWR,
> +
> + /* I2C */
> + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> +
> + /* SPI */
> + GPIO34_GPIO, /* SPDIF_CS */
> + GPIO96_GPIO, /* MCLK_CS */
> + GPIO125_GPIO, /* ACCEL_CS */
> +
> + /* MMC */
> + GPIO3_MMC1_DAT0,
> + GPIO4_MMC1_DAT1,
> + GPIO5_MMC1_DAT2,
> + GPIO6_MMC1_DAT3,
> + GPIO7_MMC1_CLK,
> + GPIO8_MMC1_CMD,
> +
> + /* One-wire */
> + GPIO126_GPIO | MFP_LPM_FLOAT,
> + GPIO105_GPIO | MFP_PULL_LOW | MFP_LPM_PULL_LOW,
> +
> + /* CHRG_USB_OK */
> + GPIO101_GPIO | MFP_PULL_HIGH,
> + /* CHRG_USB_OK */
> + GPIO112_GPIO | MFP_PULL_HIGH,
> + /* CHRG_USB_SUSP */
> + GPIO102_GPIO,
> + /* DISPLAY_ENABLE */
> + GPIO106_GPIO,
> + /* DOCK_DETECT */
> + GPIO116_GPIO | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> +
> + /* LCD */
> + GPIO54_LCD_LDD_0,
> + GPIO55_LCD_LDD_1,
> + GPIO56_LCD_LDD_2,
> + GPIO57_LCD_LDD_3,
> + GPIO58_LCD_LDD_4,
> + GPIO59_LCD_LDD_5,
> + GPIO60_LCD_LDD_6,
> + GPIO61_LCD_LDD_7,
> + GPIO62_LCD_LDD_8,
> + GPIO63_LCD_LDD_9,
> + GPIO64_LCD_LDD_10,
> + GPIO65_LCD_LDD_11,
> + GPIO66_LCD_LDD_12,
> + GPIO67_LCD_LDD_13,
> + GPIO68_LCD_LDD_14,
> + GPIO69_LCD_LDD_15,
> + GPIO70_LCD_LDD_16,
> + GPIO71_LCD_LDD_17,
> + GPIO72_LCD_FCLK,
> + GPIO73_LCD_LCLK,
> + GPIO74_LCD_PCLK,
> + GPIO75_LCD_BIAS,
> +};
> +
> +static mfp_cfg_t __raumfeld_connector_pin_config[] = {
> + /* UART1 */
> + GPIO77_UART1_RXD,
> + GPIO78_UART1_TXD,
> + GPIO79_UART1_CTS,
> + GPIO81_UART1_DSR,
> + GPIO83_UART1_DTR,
> + GPIO84_UART1_RTS,
> +
> + /* UART3 */
> + GPIO110_UART3_RXD,
> +
> + /* USB Host */
> + GPIO0_2_USBH_PEN,
> + GPIO1_2_USBH_PWR,
> +
> + /* I2C */
> + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> +
> + /* SPI */
> + GPIO34_GPIO, /* SPDIF_CS */
> + GPIO96_GPIO, /* MCLK_CS */
> + GPIO125_GPIO, /* ACCEL_CS */
> +
> + /* MMC */
> + GPIO3_MMC1_DAT0,
> + GPIO4_MMC1_DAT1,
> + GPIO5_MMC1_DAT2,
> + GPIO6_MMC1_DAT3,
> + GPIO7_MMC1_CLK,
> + GPIO8_MMC1_CMD,
> +
> + /* Ethernet */
> + GPIO1_nCS2, /* CS */
> + GPIO40_GPIO | MFP_PULL_HIGH, /* IRQ */
> +
> + /* SSP for I2S */
> + GPIO85_SSP1_SCLK,
> + GPIO89_SSP1_EXTCLK,
> + GPIO86_SSP1_FRM,
> + GPIO87_SSP1_TXD,
> + GPIO88_SSP1_RXD,
> + GPIO90_SSP1_SYSCLK,
> +
> + /* SSP2 for S/PDIF */
> + GPIO25_SSP2_SCLK,
> + GPIO26_SSP2_FRM,
> + GPIO27_SSP2_TXD,
> + GPIO29_SSP2_EXTCLK,
> +};
> +
> +static mfp_cfg_t __raumfeld_speaker_pin_config[] = {
> + /* UART1 */
> + GPIO77_UART1_RXD,
> + GPIO78_UART1_TXD,
> + GPIO79_UART1_CTS,
> + GPIO81_UART1_DSR,
> + GPIO83_UART1_DTR,
> + GPIO84_UART1_RTS,
> +
> + /* UART3 */
> + GPIO110_UART3_RXD,
> +
> + /* USB Host */
> + GPIO0_2_USBH_PEN,
> + GPIO1_2_USBH_PWR,
> +
> + /* I2C */
> + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> +
> + /* SPI */
> + GPIO34_GPIO, /* SPDIF_CS */
> + GPIO96_GPIO, /* MCLK_CS */
> + GPIO125_GPIO, /* ACCEL_CS */
> +
> + /* MMC */
> + GPIO3_MMC1_DAT0,
> + GPIO4_MMC1_DAT1,
> + GPIO5_MMC1_DAT2,
> + GPIO6_MMC1_DAT3,
> + GPIO7_MMC1_CLK,
> + GPIO8_MMC1_CMD,
> +
> + /* Ethernet */
> + GPIO1_nCS2, /* CS */
> + GPIO40_GPIO | MFP_PULL_HIGH, /* IRQ */
> +
> + /* SSP for I2S */
> + GPIO85_SSP1_SCLK,
> + GPIO89_SSP1_EXTCLK,
> + GPIO86_SSP1_FRM,
> + GPIO87_SSP1_TXD,
> + GPIO88_SSP1_RXD,
> + GPIO90_SSP1_SYSCLK,
> +};
> +
> +/*
...
Why don't we separate the common MFP configuration into another table as some
platforms do ? The code duplication is horrible here ...
next prev parent reply other threads:[~2009-11-26 19:13 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-11-26 17:58 ARM: pxa: add support for Raumfeld audio devices [v2] Daniel Mack
2009-11-26 17:58 ` [PATCH 1/3] ARM: pxa/raumfeld: add platform support Daniel Mack
2009-11-26 17:59 ` [PATCH 2/3] ALSA: ARM: add Raumfeld audio support Daniel Mack
2009-11-26 17:59 ` [PATCH 3/3] ARM: pxa/raumfeld: Add defconfig Daniel Mack
2009-11-27 11:34 ` [PATCH 2/3] ALSA: ARM: add Raumfeld audio support Mark Brown
2009-11-27 12:42 ` Daniel Mack
2009-11-26 19:13 ` Marek Vasut [this message]
2009-11-26 19:17 ` [PATCH 1/3] ARM: pxa/raumfeld: add platform support Daniel Mack
2009-11-26 19:18 ` Russell King - ARM Linux
2009-11-26 22:11 ` Marek Vasut
2009-11-26 22:19 ` Russell King - ARM Linux
2009-11-27 1:49 ` Marek Vasut
2009-11-27 8:50 ` Russell King - ARM Linux
2009-11-27 5:46 ` Eric Miao
2009-11-27 10:27 ` Daniel Mack
-- strict thread matches above, loose matches on Subject: below --
2009-11-27 12:47 ARM: pxa: add support for Raumfeld audio devices [v3] Daniel Mack
2009-11-27 12:47 ` [PATCH 1/3] ARM: pxa/raumfeld: add platform support Daniel Mack
2009-11-29 3:19 ` Eric Miao
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200911262013.47713.marek.vasut@gmail.com \
--to=marek.vasut@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).