* [PATCH 1/9] omap: use smc91x_platdata to setup smc91x
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
@ 2009-12-09 0:49 ` Tony Lindgren
2009-12-09 2:13 ` Tony Lindgren
2009-12-09 0:50 ` [PATCH 2/9] smc91x: remove OMAP specific bits Tony Lindgren
` (7 subsequent siblings)
8 siblings, 1 reply; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:49 UTC (permalink / raw)
To: linux-arm-kernel
From: Ladislav Michl <ladis@linux-mips.org>
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap1/board-fsample.c | 10 ++++++++++
arch/arm/mach-omap1/board-h2.c | 10 ++++++++++
arch/arm/mach-omap1/board-h3.c | 10 ++++++++++
arch/arm/mach-omap1/board-innovator.c | 13 +++++++++++++
arch/arm/mach-omap1/board-osk.c | 10 ++++++++++
arch/arm/mach-omap1/board-perseus2.c | 10 ++++++++++
arch/arm/mach-omap1/board-voiceblue.c | 10 ++++++++++
arch/arm/mach-omap2/board-apollon.c | 10 ++++++++++
arch/arm/mach-omap2/gpmc-smc91x.c | 8 +++++---
arch/arm/plat-omap/debug-devices.c | 10 ++++++++++
10 files changed, 98 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index f4b72c1..91e7b2f 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -19,6 +19,7 @@
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/input.h>
+#include <linux/smc91x.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -100,6 +101,12 @@ static int fsample_keymap[] = {
0
};
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource smc91x_resources[] = {
[0] = {
.start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
@@ -190,6 +197,9 @@ static struct platform_device nand_device = {
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index 89ba8ec..eeafe6e 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -28,6 +28,7 @@
#include <linux/mtd/partitions.h>
#include <linux/input.h>
#include <linux/i2c/tps65010.h>
+#include <linux/smc91x.h>
#include <mach/hardware.h>
#include <asm/gpio.h>
@@ -200,6 +201,12 @@ static struct platform_device h2_nand_device = {
.resource = &h2_nand_resource,
};
+static struct smc91x_platdata h2_smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource h2_smc91x_resources[] = {
[0] = {
.start = OMAP1610_ETHR_START, /* Physical */
@@ -216,6 +223,9 @@ static struct resource h2_smc91x_resources[] = {
static struct platform_device h2_smc91x_device = {
.name = "smc91x",
.id = 0,
+ .dev = {
+ .platform_data = &h2_smc91x_info,
+ },
.num_resources = ARRAY_SIZE(h2_smc91x_resources),
.resource = h2_smc91x_resources,
};
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index f5cc0a7..e0aee66 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -28,6 +28,7 @@
#include <linux/input.h>
#include <linux/spi/spi.h>
#include <linux/i2c/tps65010.h>
+#include <linux/smc91x.h>
#include <asm/setup.h>
#include <asm/page.h>
@@ -202,6 +203,12 @@ static struct platform_device nand_device = {
.resource = &nand_resource,
};
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource smc91x_resources[] = {
[0] = {
.start = OMAP1710_ETHR_START, /* Physical */
@@ -218,6 +225,9 @@ static struct resource smc91x_resources[] = {
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index cf0fdb9..91b3b8e 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -23,6 +23,7 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/input.h>
+#include <linux/smc91x.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -159,6 +160,12 @@ static struct map_desc innovator1510_io_desc[] __initdata = {
}
};
+static struct smc91x_platdata innovator_smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource innovator1510_smc91x_resources[] = {
[0] = {
.start = OMAP1510_FPGA_ETHR_START, /* Physical */
@@ -175,6 +182,9 @@ static struct resource innovator1510_smc91x_resources[] = {
static struct platform_device innovator1510_smc91x_device = {
.name = "smc91x",
.id = 0,
+ .dev = {
+ .platform_data = &innovator_smc91x_info,
+ },
.num_resources = ARRAY_SIZE(innovator1510_smc91x_resources),
.resource = innovator1510_smc91x_resources,
};
@@ -241,6 +251,9 @@ static struct resource innovator1610_smc91x_resources[] = {
static struct platform_device innovator1610_smc91x_device = {
.name = "smc91x",
.id = 0,
+ .dev = {
+ .platform_data = &innovator_smc91x_info,
+ },
.num_resources = ARRAY_SIZE(innovator1610_smc91x_resources),
.resource = innovator1610_smc91x_resources,
};
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index 50c92c1..ccea4f4 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -33,6 +33,7 @@
#include <linux/irq.h>
#include <linux/i2c.h>
#include <linux/leds.h>
+#include <linux/smc91x.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
@@ -115,6 +116,12 @@ static struct platform_device osk5912_flash_device = {
.resource = &osk_flash_resource,
};
+static struct smc91x_platdata osk5912_smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource osk5912_smc91x_resources[] = {
[0] = {
.start = OMAP_OSK_ETHR_START, /* Physical */
@@ -131,6 +138,9 @@ static struct resource osk5912_smc91x_resources[] = {
static struct platform_device osk5912_smc91x_device = {
.name = "smc91x",
.id = -1,
+ .dev = {
+ .platform_data = &osk5912_smc91x_info,
+ },
.num_resources = ARRAY_SIZE(osk5912_smc91x_resources),
.resource = osk5912_smc91x_resources,
};
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index ca7df1e..b9ea312 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -19,6 +19,7 @@
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/input.h>
+#include <linux/smc91x.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -67,6 +68,12 @@ static int p2_keymap[] = {
0
};
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource smc91x_resources[] = {
[0] = {
.start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
@@ -157,6 +164,9 @@ static struct platform_device nand_device = {
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index 35c75c1..1691835 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -22,6 +22,7 @@
#include <linux/reboot.h>
#include <linux/serial_8250.h>
#include <linux/serial_reg.h>
+#include <linux/smc91x.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -106,6 +107,12 @@ static struct platform_device voiceblue_flash_device = {
.resource = &voiceblue_flash_resource,
};
+static struct smc91x_platdata voiceblue_smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource voiceblue_smc91x_resources[] = {
[0] = {
.start = OMAP_CS2_PHYS + 0x300,
@@ -122,6 +129,9 @@ static struct resource voiceblue_smc91x_resources[] = {
static struct platform_device voiceblue_smc91x_device = {
.name = "smc91x",
.id = 0,
+ .dev = {
+ .platform_data = &voiceblue_smc91x_info,
+ },
.num_resources = ARRAY_SIZE(voiceblue_smc91x_resources),
.resource = voiceblue_smc91x_resources,
};
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 8a2ce77..fbbd68d 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -26,6 +26,7 @@
#include <linux/leds.h>
#include <linux/err.h>
#include <linux/clk.h>
+#include <linux/smc91x.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -120,6 +121,12 @@ static void __init apollon_flash_init(void)
apollon_flash_resource[0].end = base + SZ_128K - 1;
}
+static struct smc91x_platdata appolon_smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource apollon_smc91x_resources[] = {
[0] = {
.flags = IORESOURCE_MEM,
@@ -134,6 +141,9 @@ static struct resource apollon_smc91x_resources[] = {
static struct platform_device apollon_smc91x_device = {
.name = "smc91x",
.id = -1,
+ .dev = {
+ .platform_data = &appolon_smc91x_info,
+ },
.num_resources = ARRAY_SIZE(apollon_smc91x_resources),
.resource = apollon_smc91x_resources,
};
diff --git a/arch/arm/mach-omap2/gpmc-smc91x.c b/arch/arm/mach-omap2/gpmc-smc91x.c
index 6083e21..877c6f5 100644
--- a/arch/arm/mach-omap2/gpmc-smc91x.c
+++ b/arch/arm/mach-omap2/gpmc-smc91x.c
@@ -33,17 +33,19 @@ static struct resource gpmc_smc91x_resources[] = {
};
static struct smc91x_platdata gpmc_smc91x_info = {
- .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_IO_SHIFT_0,
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_IO_SHIFT_0,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
};
static struct platform_device gpmc_smc91x_device = {
.name = "smc91x",
.id = -1,
- .num_resources = ARRAY_SIZE(gpmc_smc91x_resources),
- .resource = gpmc_smc91x_resources,
.dev = {
.platform_data = &gpmc_smc91x_info,
},
+ .num_resources = ARRAY_SIZE(gpmc_smc91x_resources),
+ .resource = gpmc_smc91x_resources,
};
/*
diff --git a/arch/arm/plat-omap/debug-devices.c b/arch/arm/plat-omap/debug-devices.c
index 09c1107..923c962 100644
--- a/arch/arm/plat-omap/debug-devices.c
+++ b/arch/arm/plat-omap/debug-devices.c
@@ -13,6 +13,7 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>
+#include <linux/smc91x.h>
#include <mach/hardware.h>
@@ -24,6 +25,12 @@
* platforms include H2, H3, H4, and Perseus2.
*/
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource smc91x_resources[] = {
[0] = {
.flags = IORESOURCE_MEM,
@@ -36,6 +43,9 @@ static struct resource smc91x_resources[] = {
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = -1,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 1/9] omap: use smc91x_platdata to setup smc91x
2009-12-09 0:49 ` [PATCH 1/9] omap: use smc91x_platdata to setup smc91x Tony Lindgren
@ 2009-12-09 2:13 ` Tony Lindgren
0 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 2:13 UTC (permalink / raw)
To: linux-arm-kernel
* Tony Lindgren <tony@atomide.com> [091208 16:48]:
> From: Ladislav Michl <ladis@linux-mips.org>
>
> Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
> in smc91x driver
>
> Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
> arch/arm/mach-omap1/board-fsample.c | 10 ++++++++++
> arch/arm/mach-omap1/board-h2.c | 10 ++++++++++
> arch/arm/mach-omap1/board-h3.c | 10 ++++++++++
> arch/arm/mach-omap1/board-innovator.c | 13 +++++++++++++
> arch/arm/mach-omap1/board-osk.c | 10 ++++++++++
> arch/arm/mach-omap1/board-perseus2.c | 10 ++++++++++
> arch/arm/mach-omap1/board-voiceblue.c | 10 ++++++++++
> arch/arm/mach-omap2/board-apollon.c | 10 ++++++++++
> arch/arm/mach-omap2/gpmc-smc91x.c | 8 +++++---
> arch/arm/plat-omap/debug-devices.c | 10 ++++++++++
> 10 files changed, 98 insertions(+), 3 deletions(-)
Looks like this needs a minor change to build for innovator 1610.
Will merge in the following fix as otherwise the smc91x_platdata
is not defined for 1610.
Tony
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH 2/9] smc91x: remove OMAP specific bits
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
2009-12-09 0:49 ` [PATCH 1/9] omap: use smc91x_platdata to setup smc91x Tony Lindgren
@ 2009-12-09 0:50 ` Tony Lindgren
2009-12-09 0:50 ` [PATCH 3/9] omap1: Use gen_nand Tony Lindgren
` (6 subsequent siblings)
8 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:50 UTC (permalink / raw)
To: linux-arm-kernel
From: Ladislav Michl <ladis@linux-mips.org>
Now that all OMAP boards are using the board resources, we don't need
to keep the arch/board specific crap in the driver header.
Cc: linux-net at vger.kernel.org
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
drivers/net/smc91x.h | 15 ---------------
1 files changed, 0 insertions(+), 15 deletions(-)
diff --git a/drivers/net/smc91x.h b/drivers/net/smc91x.h
index 7815bfc..5479954 100644
--- a/drivers/net/smc91x.h
+++ b/drivers/net/smc91x.h
@@ -206,21 +206,6 @@ SMC_outw(u16 val, void __iomem *ioaddr, int reg)
}
}
-#elif defined(CONFIG_ARCH_OMAP)
-
-/* We can only do 16-bit reads and writes in the static memory space. */
-#define SMC_CAN_USE_8BIT 0
-#define SMC_CAN_USE_16BIT 1
-#define SMC_CAN_USE_32BIT 0
-#define SMC_IO_SHIFT 0
-#define SMC_NOWAIT 1
-
-#define SMC_inw(a, r) readw((a) + (r))
-#define SMC_outw(v, a, r) writew(v, (a) + (r))
-#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
-#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
-#define SMC_IRQ_FLAGS (-1) /* from resource */
-
#elif defined(CONFIG_SH_SH4202_MICRODEV)
#define SMC_CAN_USE_8BIT 0
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 3/9] omap1: Use gen_nand
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
2009-12-09 0:49 ` [PATCH 1/9] omap: use smc91x_platdata to setup smc91x Tony Lindgren
2009-12-09 0:50 ` [PATCH 2/9] smc91x: remove OMAP specific bits Tony Lindgren
@ 2009-12-09 0:50 ` Tony Lindgren
2009-12-09 0:50 ` [PATCH 4/9] omap1: DMA: move LCD related code from plat-omap to mach-omap1 Tony Lindgren
` (5 subsequent siblings)
8 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:50 UTC (permalink / raw)
To: linux-arm-kernel
From: Ladislav Michl <ladis@linux-mips.org>
Since omapnand driver never find its way into mainline, switch to gen_nand instead.
Following patch is compile tested only, but it is based on code I wrote for
NetStar board and runtime tested it there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Kevin Hilman <kjh@hilman.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap1/board-fsample.c | 50 ++++++++++++++++++++++--------
arch/arm/mach-omap1/board-h2.c | 49 ++++++++++++++++++++++++------
arch/arm/mach-omap1/board-h3.c | 56 ++++++++++++++++++++++++----------
arch/arm/mach-omap1/board-perseus2.c | 48 ++++++++++++++++++++++-------
4 files changed, 152 insertions(+), 51 deletions(-)
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 91e7b2f..7e70c3c 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -31,7 +31,6 @@
#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/fpga.h>
-#include <plat/nand.h>
#include <plat/keypad.h>
#include <plat/common.h>
#include <plat/board.h>
@@ -174,8 +173,40 @@ static struct platform_device nor_device = {
.resource = &nor_resource,
};
-static struct omap_nand_platform_data nand_data = {
- .options = NAND_SAMSUNG_LP_OPTIONS,
+static void nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long mask;
+
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+ if (ctrl & NAND_ALE)
+ mask |= 0x04;
+ writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define FSAMPLE_NAND_RB_GPIO_PIN 62
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+ return gpio_get_value(FSAMPLE_NAND_RB_GPIO_PIN);
+}
+
+static const char *part_probes[] = { "cmdlinepart", NULL };
+
+static struct platform_nand_data nand_data = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .options = NAND_SAMSUNG_LP_OPTIONS,
+ .part_probe_types = part_probes,
+ },
+ .ctrl = {
+ .cmd_ctrl = nand_cmd_ctl,
+ .dev_ready = nand_dev_ready,
+ },
};
static struct resource nand_resource = {
@@ -185,7 +216,7 @@ static struct resource nand_resource = {
};
static struct platform_device nand_device = {
- .name = "omapnand",
+ .name = "gen_nand",
.id = 0,
.dev = {
.platform_data = &nand_data,
@@ -243,13 +274,6 @@ static struct platform_device *devices[] __initdata = {
&lcd_device,
};
-#define P2_NAND_RB_GPIO_PIN 62
-
-static int nand_dev_ready(struct omap_nand_platform_data *data)
-{
- return gpio_get_value(P2_NAND_RB_GPIO_PIN);
-}
-
static struct omap_lcd_config fsample_lcd_config __initdata = {
.ctrl_name = "internal",
};
@@ -260,9 +284,9 @@ static struct omap_board_config_kernel fsample_config[] = {
static void __init omap_fsample_init(void)
{
- if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
+ if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
- nand_data.dev_ready = nand_dev_ready;
+ gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index eeafe6e..fa7cece 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -41,7 +41,6 @@
#include <plat/mux.h>
#include <plat/dma.h>
#include <plat/tc.h>
-#include <plat/nand.h>
#include <plat/irda.h>
#include <plat/usb.h>
#include <plat/keypad.h>
@@ -180,11 +179,43 @@ static struct mtd_partition h2_nand_partitions[] = {
},
};
-/* dip switches control NAND chip access: 8 bit, 16 bit, or neither */
-static struct omap_nand_platform_data h2_nand_data = {
- .options = NAND_SAMSUNG_LP_OPTIONS,
- .parts = h2_nand_partitions,
- .nr_parts = ARRAY_SIZE(h2_nand_partitions),
+static void h2_nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long mask;
+
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+ if (ctrl & NAND_ALE)
+ mask |= 0x04;
+ writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define H2_NAND_RB_GPIO_PIN 62
+
+static int h2_nand_dev_ready(struct mtd_info *mtd)
+{
+ return gpio_get_value(H2_NAND_RB_GPIO_PIN);
+}
+
+static const char *h2_part_probes[] = { "cmdlinepart", NULL };
+
+struct platform_nand_data h2_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(h2_nand_partitions),
+ .partitions = h2_nand_partitions,
+ .options = NAND_SAMSUNG_LP_OPTIONS,
+ .part_probe_types = h2_part_probes,
+ },
+ .ctrl = {
+ .cmd_ctrl = h2_nand_cmd_ctl,
+ .dev_ready = h2_nand_dev_ready,
+
+ },
};
static struct resource h2_nand_resource = {
@@ -192,10 +223,10 @@ static struct resource h2_nand_resource = {
};
static struct platform_device h2_nand_device = {
- .name = "omapnand",
+ .name = "gen_nand",
.id = 0,
.dev = {
- .platform_data = &h2_nand_data,
+ .platform_data = &h2_nand_platdata,
},
.num_resources = 1,
.resource = &h2_nand_resource,
@@ -378,8 +409,6 @@ static struct omap_board_config_kernel h2_config[] __initdata = {
{ OMAP_TAG_LCD, &h2_lcd_config },
};
-#define H2_NAND_RB_GPIO_PIN 62
-
static void __init h2_init(void)
{
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index e0aee66..6a7f9c3 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -43,7 +43,6 @@
#include <mach/irqs.h>
#include <plat/mux.h>
#include <plat/tc.h>
-#include <plat/nand.h>
#include <plat/usb.h>
#include <plat/keypad.h>
#include <plat/dma.h>
@@ -182,11 +181,43 @@ static struct mtd_partition nand_partitions[] = {
},
};
-/* dip switches control NAND chip access: 8 bit, 16 bit, or neither */
-static struct omap_nand_platform_data nand_data = {
- .options = NAND_SAMSUNG_LP_OPTIONS,
- .parts = nand_partitions,
- .nr_parts = ARRAY_SIZE(nand_partitions),
+static void nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long mask;
+
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+ if (ctrl & NAND_ALE)
+ mask |= 0x04;
+ writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define H3_NAND_RB_GPIO_PIN 10
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+ return gpio_get_value(H3_NAND_RB_GPIO_PIN);
+}
+
+static const char *part_probes[] = { "cmdlinepart", NULL };
+
+struct platform_nand_data nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(nand_partitions),
+ .partitions = nand_partitions,
+ .options = NAND_SAMSUNG_LP_OPTIONS,
+ .part_probe_types = part_probes,
+ },
+ .ctrl = {
+ .cmd_ctrl = nand_cmd_ctl,
+ .dev_ready = nand_dev_ready,
+
+ },
};
static struct resource nand_resource = {
@@ -194,10 +225,10 @@ static struct resource nand_resource = {
};
static struct platform_device nand_device = {
- .name = "omapnand",
+ .name = "gen_nand",
.id = 0,
.dev = {
- .platform_data = &nand_data,
+ .platform_data = &nand_platdata,
},
.num_resources = 1,
.resource = &nand_resource,
@@ -342,13 +373,6 @@ static struct i2c_board_info __initdata h3_i2c_board_info[] = {
},
};
-#define H3_NAND_RB_GPIO_PIN 10
-
-static int nand_dev_ready(struct omap_nand_platform_data *data)
-{
- return gpio_get_value(H3_NAND_RB_GPIO_PIN);
-}
-
static void __init h3_init(void)
{
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
@@ -366,7 +390,7 @@ static void __init h3_init(void)
nand_resource.end += SZ_4K - 1;
if (gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
- nand_data.dev_ready = nand_dev_ready;
+ gpio_direction_input(H3_NAND_RB_GPIO_PIN);
/* GPIO10 Func_MUX_CTRL reg bit 29:27, Configure V2 to mode1 as GPIO */
/* GPIO10 pullup/down register, Enable pullup on GPIO10 */
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index b9ea312..1387a4f 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -31,7 +31,6 @@
#include <mach/gpio.h>
#include <plat/mux.h>
#include <plat/fpga.h>
-#include <plat/nand.h>
#include <plat/keypad.h>
#include <plat/common.h>
#include <plat/board.h>
@@ -141,8 +140,40 @@ static struct platform_device nor_device = {
.resource = &nor_resource,
};
-static struct omap_nand_platform_data nand_data = {
- .options = NAND_SAMSUNG_LP_OPTIONS,
+static void nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long mask;
+
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+ if (ctrl & NAND_ALE)
+ mask |= 0x04;
+ writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define P2_NAND_RB_GPIO_PIN 62
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+ return gpio_get_value(P2_NAND_RB_GPIO_PIN);
+}
+
+static const char *part_probes[] = { "cmdlinepart", NULL };
+
+static struct platform_nand_data nand_data = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .options = NAND_SAMSUNG_LP_OPTIONS,
+ .part_probe_types = part_probes,
+ },
+ .ctrl = {
+ .cmd_ctrl = nand_cmd_ctl,
+ .dev_ready = nand_dev_ready,
+ },
};
static struct resource nand_resource = {
@@ -152,7 +183,7 @@ static struct resource nand_resource = {
};
static struct platform_device nand_device = {
- .name = "omapnand",
+ .name = "gen_nand",
.id = 0,
.dev = {
.platform_data = &nand_data,
@@ -211,13 +242,6 @@ static struct platform_device *devices[] __initdata = {
&lcd_device,
};
-#define P2_NAND_RB_GPIO_PIN 62
-
-static int nand_dev_ready(struct omap_nand_platform_data *data)
-{
- return gpio_get_value(P2_NAND_RB_GPIO_PIN);
-}
-
static struct omap_lcd_config perseus2_lcd_config __initdata = {
.ctrl_name = "internal",
};
@@ -230,7 +254,7 @@ static void __init omap_perseus2_init(void)
{
if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
- nand_data.dev_ready = nand_dev_ready;
+ gpio_direction_input(P2_NAND_RB_GPIO_PIN);
omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 4/9] omap1: DMA: move LCD related code from plat-omap to mach-omap1
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
` (2 preceding siblings ...)
2009-12-09 0:50 ` [PATCH 3/9] omap1: Use gen_nand Tony Lindgren
@ 2009-12-09 0:50 ` Tony Lindgren
2009-12-09 0:50 ` [PATCH 5/9] omap1: Add omap7xx USB support Tony Lindgren
` (4 subsequent siblings)
8 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:50 UTC (permalink / raw)
To: linux-arm-kernel
From: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap1/Makefile | 4
arch/arm/mach-omap1/include/mach/lcd_dma.h | 78 +++++
arch/arm/mach-omap1/lcd_dma.c | 447 ++++++++++++++++++++++++++++
arch/arm/plat-omap/dma.c | 410 --------------------------
arch/arm/plat-omap/include/plat/dma.h | 60 +---
5 files changed, 541 insertions(+), 458 deletions(-)
create mode 100644 arch/arm/mach-omap1/include/mach/lcd_dma.h
create mode 100644 arch/arm/mach-omap1/lcd_dma.c
diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile
index 51bc195..fe75cdd 100644
--- a/arch/arm/mach-omap1/Makefile
+++ b/arch/arm/mach-omap1/Makefile
@@ -51,3 +51,7 @@ led-$(CONFIG_MACH_OMAP_INNOVATOR) += leds-innovator.o
led-$(CONFIG_MACH_OMAP_PERSEUS2) += leds-h2p2-debug.o
led-$(CONFIG_MACH_OMAP_OSK) += leds-osk.o
obj-$(CONFIG_LEDS) += $(led-y)
+
+ifneq ($(CONFIG_FB_OMAP),)
+obj-y += lcd_dma.o
+endif
diff --git a/arch/arm/mach-omap1/include/mach/lcd_dma.h b/arch/arm/mach-omap1/include/mach/lcd_dma.h
new file mode 100644
index 0000000..d7a457b
--- /dev/null
+++ b/arch/arm/mach-omap1/include/mach/lcd_dma.h
@@ -0,0 +1,78 @@
+/*
+ * arch/arm/mach-omap1/include/mach/lcd_dma.h
+ *
+ * Extracted from arch/arm/plat-omap/include/plat/dma.h
+ * Copyright (C) 2003 Nokia Corporation
+ * Author: Juha Yrj?l? <juha.yrjola@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef __MACH_OMAP1_LCD_DMA_H__
+#define __MACH_OMAP1_LCD_DMA_H__
+
+/* Hardware registers for LCD DMA */
+#define OMAP1510_DMA_LCD_BASE (0xfffedb00)
+#define OMAP1510_DMA_LCD_CTRL (OMAP1510_DMA_LCD_BASE + 0x00)
+#define OMAP1510_DMA_LCD_TOP_F1_L (OMAP1510_DMA_LCD_BASE + 0x02)
+#define OMAP1510_DMA_LCD_TOP_F1_U (OMAP1510_DMA_LCD_BASE + 0x04)
+#define OMAP1510_DMA_LCD_BOT_F1_L (OMAP1510_DMA_LCD_BASE + 0x06)
+#define OMAP1510_DMA_LCD_BOT_F1_U (OMAP1510_DMA_LCD_BASE + 0x08)
+
+#define OMAP1610_DMA_LCD_BASE (0xfffee300)
+#define OMAP1610_DMA_LCD_CSDP (OMAP1610_DMA_LCD_BASE + 0xc0)
+#define OMAP1610_DMA_LCD_CCR (OMAP1610_DMA_LCD_BASE + 0xc2)
+#define OMAP1610_DMA_LCD_CTRL (OMAP1610_DMA_LCD_BASE + 0xc4)
+#define OMAP1610_DMA_LCD_TOP_B1_L (OMAP1610_DMA_LCD_BASE + 0xc8)
+#define OMAP1610_DMA_LCD_TOP_B1_U (OMAP1610_DMA_LCD_BASE + 0xca)
+#define OMAP1610_DMA_LCD_BOT_B1_L (OMAP1610_DMA_LCD_BASE + 0xcc)
+#define OMAP1610_DMA_LCD_BOT_B1_U (OMAP1610_DMA_LCD_BASE + 0xce)
+#define OMAP1610_DMA_LCD_TOP_B2_L (OMAP1610_DMA_LCD_BASE + 0xd0)
+#define OMAP1610_DMA_LCD_TOP_B2_U (OMAP1610_DMA_LCD_BASE + 0xd2)
+#define OMAP1610_DMA_LCD_BOT_B2_L (OMAP1610_DMA_LCD_BASE + 0xd4)
+#define OMAP1610_DMA_LCD_BOT_B2_U (OMAP1610_DMA_LCD_BASE + 0xd6)
+#define OMAP1610_DMA_LCD_SRC_EI_B1 (OMAP1610_DMA_LCD_BASE + 0xd8)
+#define OMAP1610_DMA_LCD_SRC_FI_B1_L (OMAP1610_DMA_LCD_BASE + 0xda)
+#define OMAP1610_DMA_LCD_SRC_EN_B1 (OMAP1610_DMA_LCD_BASE + 0xe0)
+#define OMAP1610_DMA_LCD_SRC_FN_B1 (OMAP1610_DMA_LCD_BASE + 0xe4)
+#define OMAP1610_DMA_LCD_LCH_CTRL (OMAP1610_DMA_LCD_BASE + 0xea)
+#define OMAP1610_DMA_LCD_SRC_FI_B1_U (OMAP1610_DMA_LCD_BASE + 0xf4)
+
+/* LCD DMA block numbers */
+enum {
+ OMAP_LCD_DMA_B1_TOP,
+ OMAP_LCD_DMA_B1_BOTTOM,
+ OMAP_LCD_DMA_B2_TOP,
+ OMAP_LCD_DMA_B2_BOTTOM
+};
+
+/* LCD DMA functions */
+extern int omap_request_lcd_dma(void (*callback)(u16 status, void *data),
+ void *data);
+extern void omap_free_lcd_dma(void);
+extern void omap_setup_lcd_dma(void);
+extern void omap_enable_lcd_dma(void);
+extern void omap_stop_lcd_dma(void);
+extern void omap_set_lcd_dma_ext_controller(int external);
+extern void omap_set_lcd_dma_single_transfer(int single);
+extern void omap_set_lcd_dma_b1(unsigned long addr, u16 fb_xres, u16 fb_yres,
+ int data_type);
+extern void omap_set_lcd_dma_b1_rotation(int rotate);
+extern void omap_set_lcd_dma_b1_vxres(unsigned long vxres);
+extern void omap_set_lcd_dma_b1_mirror(int mirror);
+extern void omap_set_lcd_dma_b1_scale(unsigned int xscale, unsigned int yscale);
+
+extern int omap_lcd_dma_running(void);
+
+#endif /* __MACH_OMAP1_LCD_DMA_H__ */
diff --git a/arch/arm/mach-omap1/lcd_dma.c b/arch/arm/mach-omap1/lcd_dma.c
new file mode 100644
index 0000000..4889514
--- /dev/null
+++ b/arch/arm/mach-omap1/lcd_dma.c
@@ -0,0 +1,447 @@
+/*
+ * linux/arch/arm/mach-omap1/lcd_dma.c
+ *
+ * Extracted from arch/arm/plat-omap/dma.c
+ * Copyright (C) 2003 - 2008 Nokia Corporation
+ * Author: Juha Yrj?l? <juha.yrjola@nokia.com>
+ * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com>
+ * Graphics DMA and LCD DMA graphics tranformations
+ * by Imre Deak <imre.deak@nokia.com>
+ * OMAP2/3 support Copyright (C) 2004-2007 Texas Instruments, Inc.
+ * Merged to support both OMAP1 and OMAP2 by Tony Lindgren <tony@atomide.com>
+ * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc.
+ *
+ * Copyright (C) 2009 Texas Instruments
+ * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * Support functions for the OMAP internal DMA channels.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+
+#include <mach/hardware.h>
+#include <plat/dma.h>
+
+int omap_lcd_dma_running(void)
+{
+ /*
+ * On OMAP1510, internal LCD controller will start the transfer
+ * when it gets enabled, so assume DMA running if LCD enabled.
+ */
+ if (cpu_is_omap1510())
+ if (omap_readw(0xfffec000 + 0x00) & (1 << 0))
+ return 1;
+
+ /* Check if LCD DMA is running */
+ if (cpu_is_omap16xx())
+ if (omap_readw(OMAP1610_DMA_LCD_CCR) & OMAP_DMA_CCR_EN)
+ return 1;
+
+ return 0;
+}
+
+static struct lcd_dma_info {
+ spinlock_t lock;
+ int reserved;
+ void (*callback)(u16 status, void *data);
+ void *cb_data;
+
+ int active;
+ unsigned long addr, size;
+ int rotate, data_type, xres, yres;
+ int vxres;
+ int mirror;
+ int xscale, yscale;
+ int ext_ctrl;
+ int src_port;
+ int single_transfer;
+} lcd_dma;
+
+void omap_set_lcd_dma_b1(unsigned long addr, u16 fb_xres, u16 fb_yres,
+ int data_type)
+{
+ lcd_dma.addr = addr;
+ lcd_dma.data_type = data_type;
+ lcd_dma.xres = fb_xres;
+ lcd_dma.yres = fb_yres;
+}
+EXPORT_SYMBOL(omap_set_lcd_dma_b1);
+
+void omap_set_lcd_dma_src_port(int port)
+{
+ lcd_dma.src_port = port;
+}
+
+void omap_set_lcd_dma_ext_controller(int external)
+{
+ lcd_dma.ext_ctrl = external;
+}
+EXPORT_SYMBOL(omap_set_lcd_dma_ext_controller);
+
+void omap_set_lcd_dma_single_transfer(int single)
+{
+ lcd_dma.single_transfer = single;
+}
+EXPORT_SYMBOL(omap_set_lcd_dma_single_transfer);
+
+void omap_set_lcd_dma_b1_rotation(int rotate)
+{
+ if (cpu_is_omap1510()) {
+ printk(KERN_ERR "DMA rotation is not supported in 1510 mode\n");
+ BUG();
+ return;
+ }
+ lcd_dma.rotate = rotate;
+}
+EXPORT_SYMBOL(omap_set_lcd_dma_b1_rotation);
+
+void omap_set_lcd_dma_b1_mirror(int mirror)
+{
+ if (cpu_is_omap1510()) {
+ printk(KERN_ERR "DMA mirror is not supported in 1510 mode\n");
+ BUG();
+ }
+ lcd_dma.mirror = mirror;
+}
+EXPORT_SYMBOL(omap_set_lcd_dma_b1_mirror);
+
+void omap_set_lcd_dma_b1_vxres(unsigned long vxres)
+{
+ if (cpu_is_omap1510()) {
+ printk(KERN_ERR "DMA virtual resulotion is not supported "
+ "in 1510 mode\n");
+ BUG();
+ }
+ lcd_dma.vxres = vxres;
+}
+EXPORT_SYMBOL(omap_set_lcd_dma_b1_vxres);
+
+void omap_set_lcd_dma_b1_scale(unsigned int xscale, unsigned int yscale)
+{
+ if (cpu_is_omap1510()) {
+ printk(KERN_ERR "DMA scale is not supported in 1510 mode\n");
+ BUG();
+ }
+ lcd_dma.xscale = xscale;
+ lcd_dma.yscale = yscale;
+}
+EXPORT_SYMBOL(omap_set_lcd_dma_b1_scale);
+
+static void set_b1_regs(void)
+{
+ unsigned long top, bottom;
+ int es;
+ u16 w;
+ unsigned long en, fn;
+ long ei, fi;
+ unsigned long vxres;
+ unsigned int xscale, yscale;
+
+ switch (lcd_dma.data_type) {
+ case OMAP_DMA_DATA_TYPE_S8:
+ es = 1;
+ break;
+ case OMAP_DMA_DATA_TYPE_S16:
+ es = 2;
+ break;
+ case OMAP_DMA_DATA_TYPE_S32:
+ es = 4;
+ break;
+ default:
+ BUG();
+ return;
+ }
+
+ vxres = lcd_dma.vxres ? lcd_dma.vxres : lcd_dma.xres;
+ xscale = lcd_dma.xscale ? lcd_dma.xscale : 1;
+ yscale = lcd_dma.yscale ? lcd_dma.yscale : 1;
+ BUG_ON(vxres < lcd_dma.xres);
+
+#define PIXADDR(x, y) (lcd_dma.addr + \
+ ((y) * vxres * yscale + (x) * xscale) * es)
+#define PIXSTEP(sx, sy, dx, dy) (PIXADDR(dx, dy) - PIXADDR(sx, sy) - es + 1)
+
+ switch (lcd_dma.rotate) {
+ case 0:
+ if (!lcd_dma.mirror) {
+ top = PIXADDR(0, 0);
+ bottom = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
+ /* 1510 DMA requires the bottom address to be 2 more
+ * than the actual last memory access location. */
+ if (cpu_is_omap1510() &&
+ lcd_dma.data_type == OMAP_DMA_DATA_TYPE_S32)
+ bottom += 2;
+ ei = PIXSTEP(0, 0, 1, 0);
+ fi = PIXSTEP(lcd_dma.xres - 1, 0, 0, 1);
+ } else {
+ top = PIXADDR(lcd_dma.xres - 1, 0);
+ bottom = PIXADDR(0, lcd_dma.yres - 1);
+ ei = PIXSTEP(1, 0, 0, 0);
+ fi = PIXSTEP(0, 0, lcd_dma.xres - 1, 1);
+ }
+ en = lcd_dma.xres;
+ fn = lcd_dma.yres;
+ break;
+ case 90:
+ if (!lcd_dma.mirror) {
+ top = PIXADDR(0, lcd_dma.yres - 1);
+ bottom = PIXADDR(lcd_dma.xres - 1, 0);
+ ei = PIXSTEP(0, 1, 0, 0);
+ fi = PIXSTEP(0, 0, 1, lcd_dma.yres - 1);
+ } else {
+ top = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
+ bottom = PIXADDR(0, 0);
+ ei = PIXSTEP(0, 1, 0, 0);
+ fi = PIXSTEP(1, 0, 0, lcd_dma.yres - 1);
+ }
+ en = lcd_dma.yres;
+ fn = lcd_dma.xres;
+ break;
+ case 180:
+ if (!lcd_dma.mirror) {
+ top = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
+ bottom = PIXADDR(0, 0);
+ ei = PIXSTEP(1, 0, 0, 0);
+ fi = PIXSTEP(0, 1, lcd_dma.xres - 1, 0);
+ } else {
+ top = PIXADDR(0, lcd_dma.yres - 1);
+ bottom = PIXADDR(lcd_dma.xres - 1, 0);
+ ei = PIXSTEP(0, 0, 1, 0);
+ fi = PIXSTEP(lcd_dma.xres - 1, 1, 0, 0);
+ }
+ en = lcd_dma.xres;
+ fn = lcd_dma.yres;
+ break;
+ case 270:
+ if (!lcd_dma.mirror) {
+ top = PIXADDR(lcd_dma.xres - 1, 0);
+ bottom = PIXADDR(0, lcd_dma.yres - 1);
+ ei = PIXSTEP(0, 0, 0, 1);
+ fi = PIXSTEP(1, lcd_dma.yres - 1, 0, 0);
+ } else {
+ top = PIXADDR(0, 0);
+ bottom = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
+ ei = PIXSTEP(0, 0, 0, 1);
+ fi = PIXSTEP(0, lcd_dma.yres - 1, 1, 0);
+ }
+ en = lcd_dma.yres;
+ fn = lcd_dma.xres;
+ break;
+ default:
+ BUG();
+ return; /* Suppress warning about uninitialized vars */
+ }
+
+ if (cpu_is_omap1510()) {
+ omap_writew(top >> 16, OMAP1510_DMA_LCD_TOP_F1_U);
+ omap_writew(top, OMAP1510_DMA_LCD_TOP_F1_L);
+ omap_writew(bottom >> 16, OMAP1510_DMA_LCD_BOT_F1_U);
+ omap_writew(bottom, OMAP1510_DMA_LCD_BOT_F1_L);
+
+ return;
+ }
+
+ /* 1610 regs */
+ omap_writew(top >> 16, OMAP1610_DMA_LCD_TOP_B1_U);
+ omap_writew(top, OMAP1610_DMA_LCD_TOP_B1_L);
+ omap_writew(bottom >> 16, OMAP1610_DMA_LCD_BOT_B1_U);
+ omap_writew(bottom, OMAP1610_DMA_LCD_BOT_B1_L);
+
+ omap_writew(en, OMAP1610_DMA_LCD_SRC_EN_B1);
+ omap_writew(fn, OMAP1610_DMA_LCD_SRC_FN_B1);
+
+ w = omap_readw(OMAP1610_DMA_LCD_CSDP);
+ w &= ~0x03;
+ w |= lcd_dma.data_type;
+ omap_writew(w, OMAP1610_DMA_LCD_CSDP);
+
+ w = omap_readw(OMAP1610_DMA_LCD_CTRL);
+ /* Always set the source port as SDRAM for now*/
+ w &= ~(0x03 << 6);
+ if (lcd_dma.callback != NULL)
+ w |= 1 << 1; /* Block interrupt enable */
+ else
+ w &= ~(1 << 1);
+ omap_writew(w, OMAP1610_DMA_LCD_CTRL);
+
+ if (!(lcd_dma.rotate || lcd_dma.mirror ||
+ lcd_dma.vxres || lcd_dma.xscale || lcd_dma.yscale))
+ return;
+
+ w = omap_readw(OMAP1610_DMA_LCD_CCR);
+ /* Set the double-indexed addressing mode */
+ w |= (0x03 << 12);
+ omap_writew(w, OMAP1610_DMA_LCD_CCR);
+
+ omap_writew(ei, OMAP1610_DMA_LCD_SRC_EI_B1);
+ omap_writew(fi >> 16, OMAP1610_DMA_LCD_SRC_FI_B1_U);
+ omap_writew(fi, OMAP1610_DMA_LCD_SRC_FI_B1_L);
+}
+
+static irqreturn_t lcd_dma_irq_handler(int irq, void *dev_id)
+{
+ u16 w;
+
+ w = omap_readw(OMAP1610_DMA_LCD_CTRL);
+ if (unlikely(!(w & (1 << 3)))) {
+ printk(KERN_WARNING "Spurious LCD DMA IRQ\n");
+ return IRQ_NONE;
+ }
+ /* Ack the IRQ */
+ w |= (1 << 3);
+ omap_writew(w, OMAP1610_DMA_LCD_CTRL);
+ lcd_dma.active = 0;
+ if (lcd_dma.callback != NULL)
+ lcd_dma.callback(w, lcd_dma.cb_data);
+
+ return IRQ_HANDLED;
+}
+
+int omap_request_lcd_dma(void (*callback)(u16 status, void *data),
+ void *data)
+{
+ spin_lock_irq(&lcd_dma.lock);
+ if (lcd_dma.reserved) {
+ spin_unlock_irq(&lcd_dma.lock);
+ printk(KERN_ERR "LCD DMA channel already reserved\n");
+ BUG();
+ return -EBUSY;
+ }
+ lcd_dma.reserved = 1;
+ spin_unlock_irq(&lcd_dma.lock);
+ lcd_dma.callback = callback;
+ lcd_dma.cb_data = data;
+ lcd_dma.active = 0;
+ lcd_dma.single_transfer = 0;
+ lcd_dma.rotate = 0;
+ lcd_dma.vxres = 0;
+ lcd_dma.mirror = 0;
+ lcd_dma.xscale = 0;
+ lcd_dma.yscale = 0;
+ lcd_dma.ext_ctrl = 0;
+ lcd_dma.src_port = 0;
+
+ return 0;
+}
+EXPORT_SYMBOL(omap_request_lcd_dma);
+
+void omap_free_lcd_dma(void)
+{
+ spin_lock(&lcd_dma.lock);
+ if (!lcd_dma.reserved) {
+ spin_unlock(&lcd_dma.lock);
+ printk(KERN_ERR "LCD DMA is not reserved\n");
+ BUG();
+ return;
+ }
+ if (!cpu_is_omap1510())
+ omap_writew(omap_readw(OMAP1610_DMA_LCD_CCR) & ~1,
+ OMAP1610_DMA_LCD_CCR);
+ lcd_dma.reserved = 0;
+ spin_unlock(&lcd_dma.lock);
+}
+EXPORT_SYMBOL(omap_free_lcd_dma);
+
+void omap_enable_lcd_dma(void)
+{
+ u16 w;
+
+ /*
+ * Set the Enable bit only if an external controller is
+ * connected. Otherwise the OMAP internal controller will
+ * start the transfer when it gets enabled.
+ */
+ if (cpu_is_omap1510() || !lcd_dma.ext_ctrl)
+ return;
+
+ w = omap_readw(OMAP1610_DMA_LCD_CTRL);
+ w |= 1 << 8;
+ omap_writew(w, OMAP1610_DMA_LCD_CTRL);
+
+ lcd_dma.active = 1;
+
+ w = omap_readw(OMAP1610_DMA_LCD_CCR);
+ w |= 1 << 7;
+ omap_writew(w, OMAP1610_DMA_LCD_CCR);
+}
+EXPORT_SYMBOL(omap_enable_lcd_dma);
+
+void omap_setup_lcd_dma(void)
+{
+ BUG_ON(lcd_dma.active);
+ if (!cpu_is_omap1510()) {
+ /* Set some reasonable defaults */
+ omap_writew(0x5440, OMAP1610_DMA_LCD_CCR);
+ omap_writew(0x9102, OMAP1610_DMA_LCD_CSDP);
+ omap_writew(0x0004, OMAP1610_DMA_LCD_LCH_CTRL);
+ }
+ set_b1_regs();
+ if (!cpu_is_omap1510()) {
+ u16 w;
+
+ w = omap_readw(OMAP1610_DMA_LCD_CCR);
+ /*
+ * If DMA was already active set the end_prog bit to have
+ * the programmed register set loaded into the active
+ * register set.
+ */
+ w |= 1 << 11; /* End_prog */
+ if (!lcd_dma.single_transfer)
+ w |= (3 << 8); /* Auto_init, repeat */
+ omap_writew(w, OMAP1610_DMA_LCD_CCR);
+ }
+}
+EXPORT_SYMBOL(omap_setup_lcd_dma);
+
+void omap_stop_lcd_dma(void)
+{
+ u16 w;
+
+ lcd_dma.active = 0;
+ if (cpu_is_omap1510() || !lcd_dma.ext_ctrl)
+ return;
+
+ w = omap_readw(OMAP1610_DMA_LCD_CCR);
+ w &= ~(1 << 7);
+ omap_writew(w, OMAP1610_DMA_LCD_CCR);
+
+ w = omap_readw(OMAP1610_DMA_LCD_CTRL);
+ w &= ~(1 << 8);
+ omap_writew(w, OMAP1610_DMA_LCD_CTRL);
+}
+EXPORT_SYMBOL(omap_stop_lcd_dma);
+
+static int __init omap_init_lcd_dma(void)
+{
+ int r;
+
+ if (cpu_is_omap16xx()) {
+ u16 w;
+
+ /* this would prevent OMAP sleep */
+ w = omap_readw(OMAP1610_DMA_LCD_CTRL);
+ w &= ~(1 << 8);
+ omap_writew(w, OMAP1610_DMA_LCD_CTRL);
+ }
+
+ spin_lock_init(&lcd_dma.lock);
+
+ r = request_irq(INT_DMA_LCD, lcd_dma_irq_handler, 0,
+ "LCD DMA", NULL);
+ if (r != 0)
+ printk(KERN_ERR "unable to request IRQ for LCD DMA "
+ "(error %d)\n", r);
+
+ return r;
+}
+
+arch_initcall(omap_init_lcd_dma);
+
diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c
index be4ce07..3897f56 100644
--- a/arch/arm/plat-omap/dma.c
+++ b/arch/arm/plat-omap/dma.c
@@ -47,7 +47,6 @@ enum { DMA_CHAIN_STARTED, DMA_CHAIN_NOTSTARTED };
#endif
#define OMAP_DMA_ACTIVE 0x01
-#define OMAP_DMA_CCR_EN (1 << 7)
#define OMAP2_DMA_CSR_CLEAR_MASK 0xffe
#define OMAP_FUNC_MUX_ARM_BASE (0xfffe1000 + 0xec)
@@ -1120,17 +1119,8 @@ int omap_dma_running(void)
{
int lch;
- /*
- * On OMAP1510, internal LCD controller will start the transfer
- * when it gets enabled, so assume DMA running if LCD enabled.
- */
- if (cpu_is_omap1510())
- if (omap_readw(0xfffec000 + 0x00) & (1 << 0))
- return 1;
-
- /* Check if LCD DMA is running */
- if (cpu_is_omap16xx())
- if (omap_readw(OMAP1610_DMA_LCD_CCR) & OMAP_DMA_CCR_EN)
+ if (cpu_class_is_omap1())
+ if (omap_lcd_dma_running())
return 1;
for (lch = 0; lch < dma_chan_count; lch++)
@@ -1990,377 +1980,6 @@ static struct irqaction omap24xx_dma_irq;
/*----------------------------------------------------------------------------*/
-static struct lcd_dma_info {
- spinlock_t lock;
- int reserved;
- void (*callback)(u16 status, void *data);
- void *cb_data;
-
- int active;
- unsigned long addr, size;
- int rotate, data_type, xres, yres;
- int vxres;
- int mirror;
- int xscale, yscale;
- int ext_ctrl;
- int src_port;
- int single_transfer;
-} lcd_dma;
-
-void omap_set_lcd_dma_b1(unsigned long addr, u16 fb_xres, u16 fb_yres,
- int data_type)
-{
- lcd_dma.addr = addr;
- lcd_dma.data_type = data_type;
- lcd_dma.xres = fb_xres;
- lcd_dma.yres = fb_yres;
-}
-EXPORT_SYMBOL(omap_set_lcd_dma_b1);
-
-void omap_set_lcd_dma_src_port(int port)
-{
- lcd_dma.src_port = port;
-}
-
-void omap_set_lcd_dma_ext_controller(int external)
-{
- lcd_dma.ext_ctrl = external;
-}
-EXPORT_SYMBOL(omap_set_lcd_dma_ext_controller);
-
-void omap_set_lcd_dma_single_transfer(int single)
-{
- lcd_dma.single_transfer = single;
-}
-EXPORT_SYMBOL(omap_set_lcd_dma_single_transfer);
-
-void omap_set_lcd_dma_b1_rotation(int rotate)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA rotation is not supported in 1510 mode\n");
- BUG();
- return;
- }
- lcd_dma.rotate = rotate;
-}
-EXPORT_SYMBOL(omap_set_lcd_dma_b1_rotation);
-
-void omap_set_lcd_dma_b1_mirror(int mirror)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA mirror is not supported in 1510 mode\n");
- BUG();
- }
- lcd_dma.mirror = mirror;
-}
-EXPORT_SYMBOL(omap_set_lcd_dma_b1_mirror);
-
-void omap_set_lcd_dma_b1_vxres(unsigned long vxres)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA virtual resulotion is not supported "
- "in 1510 mode\n");
- BUG();
- }
- lcd_dma.vxres = vxres;
-}
-EXPORT_SYMBOL(omap_set_lcd_dma_b1_vxres);
-
-void omap_set_lcd_dma_b1_scale(unsigned int xscale, unsigned int yscale)
-{
- if (omap_dma_in_1510_mode()) {
- printk(KERN_ERR "DMA scale is not supported in 1510 mode\n");
- BUG();
- }
- lcd_dma.xscale = xscale;
- lcd_dma.yscale = yscale;
-}
-EXPORT_SYMBOL(omap_set_lcd_dma_b1_scale);
-
-static void set_b1_regs(void)
-{
- unsigned long top, bottom;
- int es;
- u16 w;
- unsigned long en, fn;
- long ei, fi;
- unsigned long vxres;
- unsigned int xscale, yscale;
-
- switch (lcd_dma.data_type) {
- case OMAP_DMA_DATA_TYPE_S8:
- es = 1;
- break;
- case OMAP_DMA_DATA_TYPE_S16:
- es = 2;
- break;
- case OMAP_DMA_DATA_TYPE_S32:
- es = 4;
- break;
- default:
- BUG();
- return;
- }
-
- vxres = lcd_dma.vxres ? lcd_dma.vxres : lcd_dma.xres;
- xscale = lcd_dma.xscale ? lcd_dma.xscale : 1;
- yscale = lcd_dma.yscale ? lcd_dma.yscale : 1;
- BUG_ON(vxres < lcd_dma.xres);
-
-#define PIXADDR(x, y) (lcd_dma.addr + \
- ((y) * vxres * yscale + (x) * xscale) * es)
-#define PIXSTEP(sx, sy, dx, dy) (PIXADDR(dx, dy) - PIXADDR(sx, sy) - es + 1)
-
- switch (lcd_dma.rotate) {
- case 0:
- if (!lcd_dma.mirror) {
- top = PIXADDR(0, 0);
- bottom = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
- /* 1510 DMA requires the bottom address to be 2 more
- * than the actual last memory access location. */
- if (omap_dma_in_1510_mode() &&
- lcd_dma.data_type == OMAP_DMA_DATA_TYPE_S32)
- bottom += 2;
- ei = PIXSTEP(0, 0, 1, 0);
- fi = PIXSTEP(lcd_dma.xres - 1, 0, 0, 1);
- } else {
- top = PIXADDR(lcd_dma.xres - 1, 0);
- bottom = PIXADDR(0, lcd_dma.yres - 1);
- ei = PIXSTEP(1, 0, 0, 0);
- fi = PIXSTEP(0, 0, lcd_dma.xres - 1, 1);
- }
- en = lcd_dma.xres;
- fn = lcd_dma.yres;
- break;
- case 90:
- if (!lcd_dma.mirror) {
- top = PIXADDR(0, lcd_dma.yres - 1);
- bottom = PIXADDR(lcd_dma.xres - 1, 0);
- ei = PIXSTEP(0, 1, 0, 0);
- fi = PIXSTEP(0, 0, 1, lcd_dma.yres - 1);
- } else {
- top = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
- bottom = PIXADDR(0, 0);
- ei = PIXSTEP(0, 1, 0, 0);
- fi = PIXSTEP(1, 0, 0, lcd_dma.yres - 1);
- }
- en = lcd_dma.yres;
- fn = lcd_dma.xres;
- break;
- case 180:
- if (!lcd_dma.mirror) {
- top = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
- bottom = PIXADDR(0, 0);
- ei = PIXSTEP(1, 0, 0, 0);
- fi = PIXSTEP(0, 1, lcd_dma.xres - 1, 0);
- } else {
- top = PIXADDR(0, lcd_dma.yres - 1);
- bottom = PIXADDR(lcd_dma.xres - 1, 0);
- ei = PIXSTEP(0, 0, 1, 0);
- fi = PIXSTEP(lcd_dma.xres - 1, 1, 0, 0);
- }
- en = lcd_dma.xres;
- fn = lcd_dma.yres;
- break;
- case 270:
- if (!lcd_dma.mirror) {
- top = PIXADDR(lcd_dma.xres - 1, 0);
- bottom = PIXADDR(0, lcd_dma.yres - 1);
- ei = PIXSTEP(0, 0, 0, 1);
- fi = PIXSTEP(1, lcd_dma.yres - 1, 0, 0);
- } else {
- top = PIXADDR(0, 0);
- bottom = PIXADDR(lcd_dma.xres - 1, lcd_dma.yres - 1);
- ei = PIXSTEP(0, 0, 0, 1);
- fi = PIXSTEP(0, lcd_dma.yres - 1, 1, 0);
- }
- en = lcd_dma.yres;
- fn = lcd_dma.xres;
- break;
- default:
- BUG();
- return; /* Suppress warning about uninitialized vars */
- }
-
- if (omap_dma_in_1510_mode()) {
- omap_writew(top >> 16, OMAP1510_DMA_LCD_TOP_F1_U);
- omap_writew(top, OMAP1510_DMA_LCD_TOP_F1_L);
- omap_writew(bottom >> 16, OMAP1510_DMA_LCD_BOT_F1_U);
- omap_writew(bottom, OMAP1510_DMA_LCD_BOT_F1_L);
-
- return;
- }
-
- /* 1610 regs */
- omap_writew(top >> 16, OMAP1610_DMA_LCD_TOP_B1_U);
- omap_writew(top, OMAP1610_DMA_LCD_TOP_B1_L);
- omap_writew(bottom >> 16, OMAP1610_DMA_LCD_BOT_B1_U);
- omap_writew(bottom, OMAP1610_DMA_LCD_BOT_B1_L);
-
- omap_writew(en, OMAP1610_DMA_LCD_SRC_EN_B1);
- omap_writew(fn, OMAP1610_DMA_LCD_SRC_FN_B1);
-
- w = omap_readw(OMAP1610_DMA_LCD_CSDP);
- w &= ~0x03;
- w |= lcd_dma.data_type;
- omap_writew(w, OMAP1610_DMA_LCD_CSDP);
-
- w = omap_readw(OMAP1610_DMA_LCD_CTRL);
- /* Always set the source port as SDRAM for now*/
- w &= ~(0x03 << 6);
- if (lcd_dma.callback != NULL)
- w |= 1 << 1; /* Block interrupt enable */
- else
- w &= ~(1 << 1);
- omap_writew(w, OMAP1610_DMA_LCD_CTRL);
-
- if (!(lcd_dma.rotate || lcd_dma.mirror ||
- lcd_dma.vxres || lcd_dma.xscale || lcd_dma.yscale))
- return;
-
- w = omap_readw(OMAP1610_DMA_LCD_CCR);
- /* Set the double-indexed addressing mode */
- w |= (0x03 << 12);
- omap_writew(w, OMAP1610_DMA_LCD_CCR);
-
- omap_writew(ei, OMAP1610_DMA_LCD_SRC_EI_B1);
- omap_writew(fi >> 16, OMAP1610_DMA_LCD_SRC_FI_B1_U);
- omap_writew(fi, OMAP1610_DMA_LCD_SRC_FI_B1_L);
-}
-
-static irqreturn_t lcd_dma_irq_handler(int irq, void *dev_id)
-{
- u16 w;
-
- w = omap_readw(OMAP1610_DMA_LCD_CTRL);
- if (unlikely(!(w & (1 << 3)))) {
- printk(KERN_WARNING "Spurious LCD DMA IRQ\n");
- return IRQ_NONE;
- }
- /* Ack the IRQ */
- w |= (1 << 3);
- omap_writew(w, OMAP1610_DMA_LCD_CTRL);
- lcd_dma.active = 0;
- if (lcd_dma.callback != NULL)
- lcd_dma.callback(w, lcd_dma.cb_data);
-
- return IRQ_HANDLED;
-}
-
-int omap_request_lcd_dma(void (*callback)(u16 status, void *data),
- void *data)
-{
- spin_lock_irq(&lcd_dma.lock);
- if (lcd_dma.reserved) {
- spin_unlock_irq(&lcd_dma.lock);
- printk(KERN_ERR "LCD DMA channel already reserved\n");
- BUG();
- return -EBUSY;
- }
- lcd_dma.reserved = 1;
- spin_unlock_irq(&lcd_dma.lock);
- lcd_dma.callback = callback;
- lcd_dma.cb_data = data;
- lcd_dma.active = 0;
- lcd_dma.single_transfer = 0;
- lcd_dma.rotate = 0;
- lcd_dma.vxres = 0;
- lcd_dma.mirror = 0;
- lcd_dma.xscale = 0;
- lcd_dma.yscale = 0;
- lcd_dma.ext_ctrl = 0;
- lcd_dma.src_port = 0;
-
- return 0;
-}
-EXPORT_SYMBOL(omap_request_lcd_dma);
-
-void omap_free_lcd_dma(void)
-{
- spin_lock(&lcd_dma.lock);
- if (!lcd_dma.reserved) {
- spin_unlock(&lcd_dma.lock);
- printk(KERN_ERR "LCD DMA is not reserved\n");
- BUG();
- return;
- }
- if (!enable_1510_mode)
- omap_writew(omap_readw(OMAP1610_DMA_LCD_CCR) & ~1,
- OMAP1610_DMA_LCD_CCR);
- lcd_dma.reserved = 0;
- spin_unlock(&lcd_dma.lock);
-}
-EXPORT_SYMBOL(omap_free_lcd_dma);
-
-void omap_enable_lcd_dma(void)
-{
- u16 w;
-
- /*
- * Set the Enable bit only if an external controller is
- * connected. Otherwise the OMAP internal controller will
- * start the transfer when it gets enabled.
- */
- if (enable_1510_mode || !lcd_dma.ext_ctrl)
- return;
-
- w = omap_readw(OMAP1610_DMA_LCD_CTRL);
- w |= 1 << 8;
- omap_writew(w, OMAP1610_DMA_LCD_CTRL);
-
- lcd_dma.active = 1;
-
- w = omap_readw(OMAP1610_DMA_LCD_CCR);
- w |= 1 << 7;
- omap_writew(w, OMAP1610_DMA_LCD_CCR);
-}
-EXPORT_SYMBOL(omap_enable_lcd_dma);
-
-void omap_setup_lcd_dma(void)
-{
- BUG_ON(lcd_dma.active);
- if (!enable_1510_mode) {
- /* Set some reasonable defaults */
- omap_writew(0x5440, OMAP1610_DMA_LCD_CCR);
- omap_writew(0x9102, OMAP1610_DMA_LCD_CSDP);
- omap_writew(0x0004, OMAP1610_DMA_LCD_LCH_CTRL);
- }
- set_b1_regs();
- if (!enable_1510_mode) {
- u16 w;
-
- w = omap_readw(OMAP1610_DMA_LCD_CCR);
- /*
- * If DMA was already active set the end_prog bit to have
- * the programmed register set loaded into the active
- * register set.
- */
- w |= 1 << 11; /* End_prog */
- if (!lcd_dma.single_transfer)
- w |= (3 << 8); /* Auto_init, repeat */
- omap_writew(w, OMAP1610_DMA_LCD_CCR);
- }
-}
-EXPORT_SYMBOL(omap_setup_lcd_dma);
-
-void omap_stop_lcd_dma(void)
-{
- u16 w;
-
- lcd_dma.active = 0;
- if (enable_1510_mode || !lcd_dma.ext_ctrl)
- return;
-
- w = omap_readw(OMAP1610_DMA_LCD_CCR);
- w &= ~(1 << 7);
- omap_writew(w, OMAP1610_DMA_LCD_CCR);
-
- w = omap_readw(OMAP1610_DMA_LCD_CTRL);
- w &= ~(1 << 8);
- omap_writew(w, OMAP1610_DMA_LCD_CTRL);
-}
-EXPORT_SYMBOL(omap_stop_lcd_dma);
-
void omap_dma_global_context_save(void)
{
omap_dma_global_context.dma_irqenable_l0 =
@@ -2465,14 +2084,6 @@ static int __init omap_init_dma(void)
dma_chan_count = 16;
} else
dma_chan_count = 9;
- if (cpu_is_omap16xx()) {
- u16 w;
-
- /* this would prevent OMAP sleep */
- w = omap_readw(OMAP1610_DMA_LCD_CTRL);
- w &= ~(1 << 8);
- omap_writew(w, OMAP1610_DMA_LCD_CTRL);
- }
} else if (cpu_class_is_omap2()) {
u8 revision = dma_read(REVISION) & 0xff;
printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n",
@@ -2483,7 +2094,6 @@ static int __init omap_init_dma(void)
return 0;
}
- spin_lock_init(&lcd_dma.lock);
spin_lock_init(&dma_chan_lock);
for (ch = 0; ch < dma_chan_count; ch++) {
@@ -2548,22 +2158,6 @@ static int __init omap_init_dma(void)
}
}
-
- /* FIXME: Update LCD DMA to work on 24xx */
- if (cpu_class_is_omap1()) {
- r = request_irq(INT_DMA_LCD, lcd_dma_irq_handler, 0,
- "LCD DMA", NULL);
- if (r != 0) {
- int i;
-
- printk(KERN_ERR "unable to request IRQ for LCD DMA "
- "(error %d)\n", r);
- for (i = 0; i < dma_chan_count; i++)
- free_irq(omap1_dma_irq[i], (void *) (i + 1));
- goto out_free;
- }
- }
-
return 0;
out_free:
diff --git a/arch/arm/plat-omap/include/plat/dma.h b/arch/arm/plat-omap/include/plat/dma.h
index 1c017b2..4ede9e1 100644
--- a/arch/arm/plat-omap/include/plat/dma.h
+++ b/arch/arm/plat-omap/include/plat/dma.h
@@ -401,33 +401,6 @@
/*----------------------------------------------------------------------------*/
-/* Hardware registers for LCD DMA */
-#define OMAP1510_DMA_LCD_BASE (0xfffedb00)
-#define OMAP1510_DMA_LCD_CTRL (OMAP1510_DMA_LCD_BASE + 0x00)
-#define OMAP1510_DMA_LCD_TOP_F1_L (OMAP1510_DMA_LCD_BASE + 0x02)
-#define OMAP1510_DMA_LCD_TOP_F1_U (OMAP1510_DMA_LCD_BASE + 0x04)
-#define OMAP1510_DMA_LCD_BOT_F1_L (OMAP1510_DMA_LCD_BASE + 0x06)
-#define OMAP1510_DMA_LCD_BOT_F1_U (OMAP1510_DMA_LCD_BASE + 0x08)
-
-#define OMAP1610_DMA_LCD_BASE (0xfffee300)
-#define OMAP1610_DMA_LCD_CSDP (OMAP1610_DMA_LCD_BASE + 0xc0)
-#define OMAP1610_DMA_LCD_CCR (OMAP1610_DMA_LCD_BASE + 0xc2)
-#define OMAP1610_DMA_LCD_CTRL (OMAP1610_DMA_LCD_BASE + 0xc4)
-#define OMAP1610_DMA_LCD_TOP_B1_L (OMAP1610_DMA_LCD_BASE + 0xc8)
-#define OMAP1610_DMA_LCD_TOP_B1_U (OMAP1610_DMA_LCD_BASE + 0xca)
-#define OMAP1610_DMA_LCD_BOT_B1_L (OMAP1610_DMA_LCD_BASE + 0xcc)
-#define OMAP1610_DMA_LCD_BOT_B1_U (OMAP1610_DMA_LCD_BASE + 0xce)
-#define OMAP1610_DMA_LCD_TOP_B2_L (OMAP1610_DMA_LCD_BASE + 0xd0)
-#define OMAP1610_DMA_LCD_TOP_B2_U (OMAP1610_DMA_LCD_BASE + 0xd2)
-#define OMAP1610_DMA_LCD_BOT_B2_L (OMAP1610_DMA_LCD_BASE + 0xd4)
-#define OMAP1610_DMA_LCD_BOT_B2_U (OMAP1610_DMA_LCD_BASE + 0xd6)
-#define OMAP1610_DMA_LCD_SRC_EI_B1 (OMAP1610_DMA_LCD_BASE + 0xd8)
-#define OMAP1610_DMA_LCD_SRC_FI_B1_L (OMAP1610_DMA_LCD_BASE + 0xda)
-#define OMAP1610_DMA_LCD_SRC_EN_B1 (OMAP1610_DMA_LCD_BASE + 0xe0)
-#define OMAP1610_DMA_LCD_SRC_FN_B1 (OMAP1610_DMA_LCD_BASE + 0xe4)
-#define OMAP1610_DMA_LCD_LCH_CTRL (OMAP1610_DMA_LCD_BASE + 0xea)
-#define OMAP1610_DMA_LCD_SRC_FI_B1_U (OMAP1610_DMA_LCD_BASE + 0xf4)
-
#define OMAP1_DMA_TOUT_IRQ (1 << 0)
#define OMAP_DMA_DROP_IRQ (1 << 1)
#define OMAP_DMA_HALF_IRQ (1 << 2)
@@ -441,6 +414,8 @@
#define OMAP2_DMA_SUPERVISOR_ERR_IRQ (1 << 10)
#define OMAP2_DMA_MISALIGNED_ERR_IRQ (1 << 11)
+#define OMAP_DMA_CCR_EN (1 << 7)
+
#define OMAP_DMA_DATA_TYPE_S8 0x00
#define OMAP_DMA_DATA_TYPE_S16 0x01
#define OMAP_DMA_DATA_TYPE_S32 0x02
@@ -503,14 +478,6 @@
#define DMA_CH_PRIO_HIGH 0x1
#define DMA_CH_PRIO_LOW 0x0 /* Def */
-/* LCD DMA block numbers */
-enum {
- OMAP_LCD_DMA_B1_TOP,
- OMAP_LCD_DMA_B1_BOTTOM,
- OMAP_LCD_DMA_B2_TOP,
- OMAP_LCD_DMA_B2_BOTTOM
-};
-
enum omap_dma_burst_mode {
OMAP_DMA_DATA_BURST_DIS = 0,
OMAP_DMA_DATA_BURST_4,
@@ -661,20 +628,13 @@ extern int omap_modify_dma_chain_params(int chain_id,
extern int omap_dma_chain_status(int chain_id);
#endif
-/* LCD DMA functions */
-extern int omap_request_lcd_dma(void (*callback)(u16 status, void *data),
- void *data);
-extern void omap_free_lcd_dma(void);
-extern void omap_setup_lcd_dma(void);
-extern void omap_enable_lcd_dma(void);
-extern void omap_stop_lcd_dma(void);
-extern void omap_set_lcd_dma_ext_controller(int external);
-extern void omap_set_lcd_dma_single_transfer(int single);
-extern void omap_set_lcd_dma_b1(unsigned long addr, u16 fb_xres, u16 fb_yres,
- int data_type);
-extern void omap_set_lcd_dma_b1_rotation(int rotate);
-extern void omap_set_lcd_dma_b1_vxres(unsigned long vxres);
-extern void omap_set_lcd_dma_b1_mirror(int mirror);
-extern void omap_set_lcd_dma_b1_scale(unsigned int xscale, unsigned int yscale);
+#if defined(CONFIG_ARCH_OMAP1) && defined(CONFIG_FB_OMAP)
+#include <mach/lcd_dma.h>
+#else
+static inline int omap_lcd_dma_running(void)
+{
+ return 0;
+}
+#endif
#endif /* __ASM_ARCH_DMA_H */
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 5/9] omap1: Add omap7xx USB support
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
` (3 preceding siblings ...)
2009-12-09 0:50 ` [PATCH 4/9] omap1: DMA: move LCD related code from plat-omap to mach-omap1 Tony Lindgren
@ 2009-12-09 0:50 ` Tony Lindgren
2009-12-09 0:51 ` [PATCH 6/9] omap1: I2C mux and clocks for omap7xx Tony Lindgren
` (3 subsequent siblings)
8 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:50 UTC (permalink / raw)
To: linux-arm-kernel
From: Cory Maccarrone <darkstar6262@gmail.com>
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap1/board-htcherald.c | 64 +++++++++++++++++++++++++++++++++
arch/arm/mach-omap1/mux.c | 4 ++
arch/arm/plat-omap/include/plat/mux.h | 2 +
arch/arm/plat-omap/usb.c | 8 ++++
4 files changed, 76 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c
index 5f28a5c..e36639f 100644
--- a/arch/arm/mach-omap1/board-htcherald.c
+++ b/arch/arm/mach-omap1/board-htcherald.c
@@ -39,6 +39,7 @@
#include <plat/common.h>
#include <plat/board.h>
#include <plat/keypad.h>
+#include <plat/usb.h>
#include <mach/irqs.h>
@@ -140,6 +141,15 @@ static struct platform_device kp_device = {
.resource = kp_resources,
};
+/* USB Device */
+static struct omap_usb_config htcherald_usb_config __initdata = {
+ .otg = 0,
+ .register_host = 0,
+ .register_dev = 1,
+ .hmc_mode = 4,
+ .pins[0] = 2,
+};
+
/* LCD Device resources */
static struct platform_device lcd_device = {
.name = "lcd_htcherald",
@@ -214,6 +224,57 @@ static void __init htcherald_disable_watchdog(void)
}
}
+#define HTCHERALD_GPIO_USB_EN1 33
+#define HTCHERALD_GPIO_USB_EN2 73
+#define HTCHERALD_GPIO_USB_DM 35
+#define HTCHERALD_GPIO_USB_DP 36
+
+static void __init htcherald_usb_enable(void)
+{
+ unsigned int tries = 20;
+ unsigned int value = 0;
+
+ /* Request the GPIOs we need to control here */
+ if (gpio_request(HTCHERALD_GPIO_USB_EN1, "herald_usb") < 0)
+ goto err1;
+
+ if (gpio_request(HTCHERALD_GPIO_USB_EN2, "herald_usb") < 0)
+ goto err2;
+
+ if (gpio_request(HTCHERALD_GPIO_USB_DM, "herald_usb") < 0)
+ goto err3;
+
+ if (gpio_request(HTCHERALD_GPIO_USB_DP, "herald_usb") < 0)
+ goto err4;
+
+ /* force USB_EN GPIO to 0 */
+ do {
+ /* output low */
+ gpio_direction_output(HTCHERALD_GPIO_USB_EN1, 0);
+ } while ((value = gpio_get_value(HTCHERALD_GPIO_USB_EN1)) == 1 &&
+ --tries);
+
+ if (value == 1)
+ printk(KERN_WARNING "Unable to reset USB, trying to continue\n");
+
+ gpio_direction_output(HTCHERALD_GPIO_USB_EN2, 0); /* output low */
+ gpio_direction_input(HTCHERALD_GPIO_USB_DM); /* input */
+ gpio_direction_input(HTCHERALD_GPIO_USB_DP); /* input */
+
+ goto done;
+
+err4:
+ gpio_free(HTCHERALD_GPIO_USB_DM);
+err3:
+ gpio_free(HTCHERALD_GPIO_USB_EN2);
+err2:
+ gpio_free(HTCHERALD_GPIO_USB_EN1);
+err1:
+ printk(KERN_ERR "Unabled to request GPIO for USB\n");
+done:
+ printk(KERN_INFO "USB setup complete.\n");
+}
+
static void __init htcherald_init(void)
{
printk(KERN_INFO "HTC Herald init.\n");
@@ -225,6 +286,9 @@ static void __init htcherald_init(void)
platform_add_devices(devices, ARRAY_SIZE(devices));
htcherald_disable_watchdog();
+
+ htcherald_usb_enable();
+ omap_usb_init(&htcherald_usb_config);
}
static void __init htcherald_init_irq(void)
diff --git a/arch/arm/mach-omap1/mux.c b/arch/arm/mach-omap1/mux.c
index 785371e..5e183cd 100644
--- a/arch/arm/mach-omap1/mux.c
+++ b/arch/arm/mach-omap1/mux.c
@@ -50,7 +50,9 @@ MUX_CFG_7XX("E3_7XX_KBC4", 13, 25, 0, 24, 1, 0)
MUX_CFG_7XX("AA17_7XX_USB_DM", 2, 21, 0, 20, 0, 0)
MUX_CFG_7XX("W16_7XX_USB_PU_EN", 2, 25, 0, 24, 0, 0)
-MUX_CFG_7XX("W17_7XX_USB_VBUSI", 2, 29, 0, 28, 0, 0)
+MUX_CFG_7XX("W17_7XX_USB_VBUSI", 2, 29, 6, 28, 1, 0)
+MUX_CFG_7XX("W18_7XX_USB_DMCK_OUT",3, 3, 1, 2, 0, 0)
+MUX_CFG_7XX("W19_7XX_USB_DCRST", 3, 7, 1, 6, 0, 0)
/* MMC Pins */
MUX_CFG_7XX("MMC_7XX_CMD", 2, 9, 0, 8, 1, 0)
diff --git a/arch/arm/plat-omap/include/plat/mux.h b/arch/arm/plat-omap/include/plat/mux.h
index 6067cf7..8ed5f25 100644
--- a/arch/arm/plat-omap/include/plat/mux.h
+++ b/arch/arm/plat-omap/include/plat/mux.h
@@ -172,6 +172,8 @@ enum omap7xx_index {
AA17_7XX_USB_DM,
W16_7XX_USB_PU_EN,
W17_7XX_USB_VBUSI,
+ W18_7XX_USB_DMCK_OUT,
+ W19_7XX_USB_DCRST,
/* MMC */
MMC_7XX_CMD,
diff --git a/arch/arm/plat-omap/usb.c b/arch/arm/plat-omap/usb.c
index 51033a4..d3bf17c 100644
--- a/arch/arm/plat-omap/usb.c
+++ b/arch/arm/plat-omap/usb.c
@@ -137,7 +137,13 @@ static u32 __init omap_usb0_init(unsigned nwires, unsigned is_device)
if (is_device) {
if (cpu_is_omap24xx())
omap_cfg_reg(J20_24XX_USB0_PUEN);
- else
+ else if (cpu_is_omap7xx()) {
+ omap_cfg_reg(AA17_7XX_USB_DM);
+ omap_cfg_reg(W16_7XX_USB_PU_EN);
+ omap_cfg_reg(W17_7XX_USB_VBUSI);
+ omap_cfg_reg(W18_7XX_USB_DMCK_OUT);
+ omap_cfg_reg(W19_7XX_USB_DCRST);
+ } else
omap_cfg_reg(W4_USB_PUEN);
}
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 6/9] omap1: I2C mux and clocks for omap7xx
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
` (4 preceding siblings ...)
2009-12-09 0:50 ` [PATCH 5/9] omap1: Add omap7xx USB support Tony Lindgren
@ 2009-12-09 0:51 ` Tony Lindgren
2009-12-09 0:51 ` [PATCH 7/9] omap3: Board file of Always Innovating OMAP3-based Touch Book Tony Lindgren
` (2 subsequent siblings)
8 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:51 UTC (permalink / raw)
To: linux-arm-kernel
From: Cory Maccarrone <darkstar6262@gmail.com>
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap1/clock.c | 4 ++--
arch/arm/mach-omap1/i2c.c | 10 ++++++++--
arch/arm/mach-omap1/mux.c | 4 ++++
arch/arm/plat-omap/include/plat/mux.h | 4 ++++
4 files changed, 18 insertions(+), 4 deletions(-)
diff --git a/arch/arm/mach-omap1/clock.c b/arch/arm/mach-omap1/clock.c
index 42cbe20..dc8ca91 100644
--- a/arch/arm/mach-omap1/clock.c
+++ b/arch/arm/mach-omap1/clock.c
@@ -132,9 +132,9 @@ static struct omap_clk omap_clks[] = {
CLK("mmci-omap.1", "ick", &armper_ck.clk, CK_16XX),
/* Virtual clocks */
CLK(NULL, "mpu", &virtual_ck_mpu, CK_16XX | CK_1510 | CK_310),
- CLK("i2c_omap.1", "fck", &i2c_fck, CK_16XX | CK_1510 | CK_310),
+ CLK("i2c_omap.1", "fck", &i2c_fck, CK_16XX | CK_1510 | CK_310 | CK_7XX),
CLK("i2c_omap.1", "ick", &i2c_ick, CK_16XX),
- CLK("i2c_omap.1", "ick", &dummy_ck, CK_1510 | CK_310),
+ CLK("i2c_omap.1", "ick", &dummy_ck, CK_1510 | CK_310 | CK_7XX),
CLK("omap_uwire", "fck", &armxor_ck.clk, CK_16XX | CK_1510 | CK_310),
CLK("omap-mcbsp.1", "ick", &dspper_ck, CK_16XX),
CLK("omap-mcbsp.1", "ick", &dummy_ck, CK_1510 | CK_310),
diff --git a/arch/arm/mach-omap1/i2c.c b/arch/arm/mach-omap1/i2c.c
index bc9d12b..1bf4735 100644
--- a/arch/arm/mach-omap1/i2c.c
+++ b/arch/arm/mach-omap1/i2c.c
@@ -21,13 +21,19 @@
#include <plat/i2c.h>
#include <plat/mux.h>
+#include <plat/cpu.h>
int __init omap_register_i2c_bus(int bus_id, u32 clkrate,
struct i2c_board_info const *info,
unsigned len)
{
- omap_cfg_reg(I2C_SDA);
- omap_cfg_reg(I2C_SCL);
+ if (cpu_is_omap7xx()) {
+ omap_cfg_reg(I2C_7XX_SDA);
+ omap_cfg_reg(I2C_7XX_SCL);
+ } else {
+ omap_cfg_reg(I2C_SDA);
+ omap_cfg_reg(I2C_SCL);
+ }
return omap_plat_register_i2c_bus(bus_id, clkrate, info, len);
}
diff --git a/arch/arm/mach-omap1/mux.c b/arch/arm/mach-omap1/mux.c
index 5e183cd..07212cc 100644
--- a/arch/arm/mach-omap1/mux.c
+++ b/arch/arm/mach-omap1/mux.c
@@ -58,6 +58,10 @@ MUX_CFG_7XX("W19_7XX_USB_DCRST", 3, 7, 1, 6, 0, 0)
MUX_CFG_7XX("MMC_7XX_CMD", 2, 9, 0, 8, 1, 0)
MUX_CFG_7XX("MMC_7XX_CLK", 2, 13, 0, 12, 1, 0)
MUX_CFG_7XX("MMC_7XX_DAT0", 2, 17, 0, 16, 1, 0)
+
+/* I2C interface */
+MUX_CFG_7XX("I2C_7XX_SCL", 5, 1, 0, 0, 1, 0)
+MUX_CFG_7XX("I2C_7XX_SDA", 5, 5, 0, 0, 1, 0)
};
#define OMAP7XX_PINS_SZ ARRAY_SIZE(omap7xx_pins)
#else
diff --git a/arch/arm/plat-omap/include/plat/mux.h b/arch/arm/plat-omap/include/plat/mux.h
index 8ed5f25..8f069cc 100644
--- a/arch/arm/plat-omap/include/plat/mux.h
+++ b/arch/arm/plat-omap/include/plat/mux.h
@@ -179,6 +179,10 @@ enum omap7xx_index {
MMC_7XX_CMD,
MMC_7XX_CLK,
MMC_7XX_DAT0,
+
+ /* I2C */
+ I2C_7XX_SCL,
+ I2C_7XX_SDA,
};
enum omap1xxx_index {
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 7/9] omap3: Board file of Always Innovating OMAP3-based Touch Book
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
` (5 preceding siblings ...)
2009-12-09 0:51 ` [PATCH 6/9] omap1: I2C mux and clocks for omap7xx Tony Lindgren
@ 2009-12-09 0:51 ` Tony Lindgren
2009-12-09 0:51 ` [PATCH 8/9] omap3: Defconfig " Tony Lindgren
2009-12-09 0:51 ` [PATCH 9/9] omap3: pandora: board file updates for .33 Tony Lindgren
8 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:51 UTC (permalink / raw)
To: linux-arm-kernel
From: Gregoire Gentil <gregoire@gentil.com>
Board file of Always Innovating OMAP3-based Touch Book
Signed-off-by: Gregoire Gentil <gregoire@gentil.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 5
arch/arm/mach-omap2/Makefile | 3
arch/arm/mach-omap2/board-omap3touchbook.c | 572 ++++++++++++++++++++++++++++
3 files changed, 579 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/mach-omap2/board-omap3touchbook.c
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index afa184a..2ea50bf 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -90,6 +90,11 @@ config MACH_OMAP3_PANDORA
depends on ARCH_OMAP3 && ARCH_OMAP34XX
select OMAP_PACKAGE_CBB
+config MACH_OMAP3_TOUCHBOOK
+ bool "OMAP3 Touch Book"
+ depends on ARCH_OMAP3 && ARCH_OMAP34XX
+ select BACKLIGHT_CLASS_DEVICE
+
config MACH_OMAP_3430SDP
bool "OMAP 3430 SDP board"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 1cc1d26..0c5d886 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -99,7 +99,8 @@ obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \
mmc-twl4030.o
obj-$(CONFIG_MACH_IGEP0020) += board-igep0020.o \
mmc-twl4030.o
-
+obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK) += board-omap3touchbook.o \
+ mmc-twl4030.o
obj-$(CONFIG_MACH_OMAP_4430SDP) += board-4430sdp.o
obj-$(CONFIG_MACH_OMAP3517EVM) += board-am3517evm.o
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
new file mode 100644
index 0000000..c9e5ebb
--- /dev/null
+++ b/arch/arm/mach-omap2/board-omap3touchbook.c
@@ -0,0 +1,572 @@
+/*
+ * linux/arch/arm/mach-omap2/board-omap3touchbook.c
+ *
+ * Copyright (C) 2009 Always Innovating
+ *
+ * Modified from mach-omap2/board-omap3beagleboard.c
+ *
+ * Initial code: Gr?goire Gentil, Tim Yamin
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+
+#include <plat/mcspi.h>
+#include <linux/spi/spi.h>
+
+#include <linux/spi/ads7846.h>
+
+#include <linux/regulator/machine.h>
+#include <linux/i2c/twl4030.h>
+
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/flash.h>
+
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/gpmc.h>
+#include <plat/nand.h>
+#include <plat/usb.h>
+#include <plat/timer-gp.h>
+
+#include "mux.h"
+#include "mmc-twl4030.h"
+
+#include <asm/setup.h>
+
+#define GPMC_CS0_BASE 0x60
+#define GPMC_CS_SIZE 0x30
+
+#define NAND_BLOCK_SIZE SZ_128K
+
+#define OMAP3_AC_GPIO 136
+#define OMAP3_TS_GPIO 162
+#define TB_BL_PWM_TIMER 9
+#define TB_KILL_POWER_GPIO 168
+
+unsigned long touchbook_revision;
+
+static struct mtd_partition omap3touchbook_nand_partitions[] = {
+ /* All the partition sizes are listed in terms of NAND block size */
+ {
+ .name = "X-Loader",
+ .offset = 0,
+ .size = 4 * NAND_BLOCK_SIZE,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "U-Boot",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
+ .size = 15 * NAND_BLOCK_SIZE,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "U-Boot Env",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
+ .size = 1 * NAND_BLOCK_SIZE,
+ },
+ {
+ .name = "Kernel",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
+ .size = 32 * NAND_BLOCK_SIZE,
+ },
+ {
+ .name = "File System",
+ .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct omap_nand_platform_data omap3touchbook_nand_data = {
+ .options = NAND_BUSWIDTH_16,
+ .parts = omap3touchbook_nand_partitions,
+ .nr_parts = ARRAY_SIZE(omap3touchbook_nand_partitions),
+ .dma_channel = -1, /* disable DMA in OMAP NAND driver */
+ .nand_setup = NULL,
+ .dev_ready = NULL,
+};
+
+static struct resource omap3touchbook_nand_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device omap3touchbook_nand_device = {
+ .name = "omap2-nand",
+ .id = -1,
+ .dev = {
+ .platform_data = &omap3touchbook_nand_data,
+ },
+ .num_resources = 1,
+ .resource = &omap3touchbook_nand_resource,
+};
+
+#include "sdram-micron-mt46h32m32lf-6.h"
+
+static struct twl4030_hsmmc_info mmc[] = {
+ {
+ .mmc = 1,
+ .wires = 8,
+ .gpio_wp = 29,
+ },
+ {} /* Terminator */
+};
+
+static struct platform_device omap3_touchbook_lcd_device = {
+ .name = "omap3touchbook_lcd",
+ .id = -1,
+};
+
+static struct omap_lcd_config omap3_touchbook_lcd_config __initdata = {
+ .ctrl_name = "internal",
+};
+
+static struct regulator_consumer_supply touchbook_vmmc1_supply = {
+ .supply = "vmmc",
+};
+
+static struct regulator_consumer_supply touchbook_vsim_supply = {
+ .supply = "vmmc_aux",
+};
+
+static struct gpio_led gpio_leds[];
+
+static int touchbook_twl_gpio_setup(struct device *dev,
+ unsigned gpio, unsigned ngpio)
+{
+ if (system_rev >= 0x20 && system_rev <= 0x34301000) {
+ omap_mux_init_gpio(23, OMAP_PIN_INPUT);
+ mmc[0].gpio_wp = 23;
+ } else {
+ omap_mux_init_gpio(29, OMAP_PIN_INPUT);
+ }
+ /* gpio + 0 is "mmc0_cd" (input/IRQ) */
+ mmc[0].gpio_cd = gpio + 0;
+ twl4030_mmc_init(mmc);
+
+ /* link regulators to MMC adapters */
+ touchbook_vmmc1_supply.dev = mmc[0].dev;
+ touchbook_vsim_supply.dev = mmc[0].dev;
+
+ /* REVISIT: need ehci-omap hooks for external VBUS
+ * power switch and overcurrent detect
+ */
+
+ gpio_request(gpio + 1, "EHCI_nOC");
+ gpio_direction_input(gpio + 1);
+
+ /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
+ gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
+ gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
+
+ /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
+ return 0;
+}
+
+static struct twl4030_gpio_platform_data touchbook_gpio_data = {
+ .gpio_base = OMAP_MAX_GPIO_LINES,
+ .irq_base = TWL4030_GPIO_IRQ_BASE,
+ .irq_end = TWL4030_GPIO_IRQ_END,
+ .use_leds = true,
+ .pullups = BIT(1),
+ .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
+ | BIT(15) | BIT(16) | BIT(17),
+ .setup = touchbook_twl_gpio_setup,
+};
+
+static struct regulator_consumer_supply touchbook_vdac_supply = {
+ .supply = "vdac",
+ .dev = &omap3_touchbook_lcd_device.dev,
+};
+
+static struct regulator_consumer_supply touchbook_vdvi_supply = {
+ .supply = "vdvi",
+ .dev = &omap3_touchbook_lcd_device.dev,
+};
+
+/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
+static struct regulator_init_data touchbook_vmmc1 = {
+ .constraints = {
+ .min_uV = 1850000,
+ .max_uV = 3150000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &touchbook_vmmc1_supply,
+};
+
+/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
+static struct regulator_init_data touchbook_vsim = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 3000000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
+ | REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &touchbook_vsim_supply,
+};
+
+/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
+static struct regulator_init_data touchbook_vdac = {
+ .constraints = {
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &touchbook_vdac_supply,
+};
+
+/* VPLL2 for digital video outputs */
+static struct regulator_init_data touchbook_vpll2 = {
+ .constraints = {
+ .name = "VDVI",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL
+ | REGULATOR_MODE_STANDBY,
+ .valid_ops_mask = REGULATOR_CHANGE_MODE
+ | REGULATOR_CHANGE_STATUS,
+ },
+ .num_consumer_supplies = 1,
+ .consumer_supplies = &touchbook_vdvi_supply,
+};
+
+static struct twl4030_usb_data touchbook_usb_data = {
+ .usb_mode = T2_USB_MODE_ULPI,
+};
+
+static struct twl4030_codec_audio_data touchbook_audio_data = {
+ .audio_mclk = 26000000,
+};
+
+static struct twl4030_codec_data touchbook_codec_data = {
+ .audio_mclk = 26000000,
+ .audio = &touchbook_audio_data,
+};
+
+static struct twl4030_platform_data touchbook_twldata = {
+ .irq_base = TWL4030_IRQ_BASE,
+ .irq_end = TWL4030_IRQ_END,
+
+ /* platform_data for children goes here */
+ .usb = &touchbook_usb_data,
+ .gpio = &touchbook_gpio_data,
+ .codec = &touchbook_codec_data,
+ .vmmc1 = &touchbook_vmmc1,
+ .vsim = &touchbook_vsim,
+ .vdac = &touchbook_vdac,
+ .vpll2 = &touchbook_vpll2,
+};
+
+static struct i2c_board_info __initdata touchbook_i2c_boardinfo[] = {
+ {
+ I2C_BOARD_INFO("twl4030", 0x48),
+ .flags = I2C_CLIENT_WAKE,
+ .irq = INT_34XX_SYS_NIRQ,
+ .platform_data = &touchbook_twldata,
+ },
+};
+
+static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = {
+ {
+ I2C_BOARD_INFO("bq27200", 0x55),
+ },
+};
+
+static int __init omap3_touchbook_i2c_init(void)
+{
+ /* Standard TouchBook bus */
+ omap_register_i2c_bus(1, 2600, touchbook_i2c_boardinfo,
+ ARRAY_SIZE(touchbook_i2c_boardinfo));
+
+ /* Additional TouchBook bus */
+ omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo,
+ ARRAY_SIZE(touchBook_i2c_boardinfo));
+
+ return 0;
+}
+
+static void __init omap3_ads7846_init(void)
+{
+ if (gpio_request(OMAP3_TS_GPIO, "ads7846_pen_down")) {
+ printk(KERN_ERR "Failed to request GPIO %d for "
+ "ads7846 pen down IRQ\n", OMAP3_TS_GPIO);
+ return;
+ }
+
+ gpio_direction_input(OMAP3_TS_GPIO);
+ omap_set_gpio_debounce(OMAP3_TS_GPIO, 1);
+ omap_set_gpio_debounce_time(OMAP3_TS_GPIO, 0xa);
+}
+
+static struct ads7846_platform_data ads7846_config = {
+ .x_min = 100,
+ .y_min = 265,
+ .x_max = 3950,
+ .y_max = 3750,
+ .x_plate_ohms = 40,
+ .pressure_max = 255,
+ .debounce_max = 10,
+ .debounce_tol = 5,
+ .debounce_rep = 1,
+ .gpio_pendown = OMAP3_TS_GPIO,
+ .keep_vref_on = 1,
+};
+
+static struct omap2_mcspi_device_config ads7846_mcspi_config = {
+ .turbo_mode = 0,
+ .single_channel = 1, /* 0: slave, 1: master */
+};
+
+static struct spi_board_info omap3_ads7846_spi_board_info[] __initdata = {
+ {
+ .modalias = "ads7846",
+ .bus_num = 4,
+ .chip_select = 0,
+ .max_speed_hz = 1500000,
+ .controller_data = &ads7846_mcspi_config,
+ .irq = OMAP_GPIO_IRQ(OMAP3_TS_GPIO),
+ .platform_data = &ads7846_config,
+ }
+};
+
+static struct gpio_led gpio_leds[] = {
+ {
+ .name = "touchbook::usr0",
+ .default_trigger = "heartbeat",
+ .gpio = 150,
+ },
+ {
+ .name = "touchbook::usr1",
+ .default_trigger = "mmc0",
+ .gpio = 149,
+ },
+ {
+ .name = "touchbook::pmu_stat",
+ .gpio = -EINVAL, /* gets replaced */
+ .active_low = true,
+ },
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+ .leds = gpio_leds,
+ .num_leds = ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device leds_gpio = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_led_info,
+ },
+};
+
+static struct gpio_keys_button gpio_buttons[] = {
+ {
+ .code = BTN_EXTRA,
+ .gpio = 7,
+ .desc = "user",
+ .wakeup = 1,
+ },
+ {
+ .code = KEY_POWER,
+ .gpio = 183,
+ .desc = "power",
+ .wakeup = 1,
+ },
+};
+
+static struct gpio_keys_platform_data gpio_key_info = {
+ .buttons = gpio_buttons,
+ .nbuttons = ARRAY_SIZE(gpio_buttons),
+};
+
+static struct platform_device keys_gpio = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &gpio_key_info,
+ },
+};
+
+static struct omap_board_config_kernel omap3_touchbook_config[] __initdata = {
+ { OMAP_TAG_LCD, &omap3_touchbook_lcd_config },
+};
+
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+ { .reg_offset = OMAP_MUX_TERMINATOR },
+};
+#else
+#define board_mux NULL
+#endif
+
+static void __init omap3_touchbook_init_irq(void)
+{
+ omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+ omap_board_config = omap3_touchbook_config;
+ omap_board_config_size = ARRAY_SIZE(omap3_touchbook_config);
+ omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+ mt46h32m32lf6_sdrc_params);
+ omap_init_irq();
+#ifdef CONFIG_OMAP_32K_TIMER
+ omap2_gp_clockevent_set_gptimer(12);
+#endif
+ omap_gpio_init();
+}
+
+static struct platform_device *omap3_touchbook_devices[] __initdata = {
+ &omap3_touchbook_lcd_device,
+ &leds_gpio,
+ &keys_gpio,
+};
+
+static void __init omap3touchbook_flash_init(void)
+{
+ u8 cs = 0;
+ u8 nandcs = GPMC_CS_NUM + 1;
+
+ u32 gpmc_base_add = OMAP34XX_GPMC_VIRT;
+
+ /* find out the chip-select on which NAND exists */
+ while (cs < GPMC_CS_NUM) {
+ u32 ret = 0;
+ ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
+
+ if ((ret & 0xC00) == 0x800) {
+ printk(KERN_INFO "Found NAND on CS%d\n", cs);
+ if (nandcs > GPMC_CS_NUM)
+ nandcs = cs;
+ }
+ cs++;
+ }
+
+ if (nandcs > GPMC_CS_NUM) {
+ printk(KERN_INFO "NAND: Unable to find configuration "
+ "in GPMC\n ");
+ return;
+ }
+
+ if (nandcs < GPMC_CS_NUM) {
+ omap3touchbook_nand_data.cs = nandcs;
+ omap3touchbook_nand_data.gpmc_cs_baseaddr = (void *)
+ (gpmc_base_add + GPMC_CS0_BASE + nandcs * GPMC_CS_SIZE);
+ omap3touchbook_nand_data.gpmc_baseaddr =
+ (void *) (gpmc_base_add);
+
+ printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
+ if (platform_device_register(&omap3touchbook_nand_device) < 0)
+ printk(KERN_ERR "Unable to register NAND device\n");
+ }
+}
+
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = 147,
+ .reset_gpio_port[2] = -EINVAL
+};
+
+static void omap3_touchbook_poweroff(void)
+{
+ int r;
+
+ r = gpio_request(TB_KILL_POWER_GPIO, "DVI reset");
+ if (r < 0) {
+ printk(KERN_ERR "Unable to get kill power GPIO\n");
+ return;
+ }
+
+ gpio_direction_output(TB_KILL_POWER_GPIO, 0);
+}
+
+static void __init early_touchbook_revision(char **p)
+{
+ if (!*p)
+ return;
+
+ strict_strtoul(*p, 10, &touchbook_revision);
+}
+__early_param("tbr=", early_touchbook_revision);
+
+static void __init omap3_touchbook_init(void)
+{
+ pm_power_off = omap3_touchbook_poweroff;
+
+ omap3_touchbook_i2c_init();
+ platform_add_devices(omap3_touchbook_devices,
+ ARRAY_SIZE(omap3_touchbook_devices));
+ omap_serial_init();
+
+ omap_mux_init_gpio(170, OMAP_PIN_INPUT);
+ gpio_request(176, "DVI_nPD");
+ /* REVISIT leave DVI powered down until it's needed ... */
+ gpio_direction_output(176, true);
+
+ /* Touchscreen and accelerometer */
+ spi_register_board_info(omap3_ads7846_spi_board_info,
+ ARRAY_SIZE(omap3_ads7846_spi_board_info));
+ omap3_ads7846_init();
+ usb_musb_init();
+ usb_ehci_init(&ehci_pdata);
+ omap3touchbook_flash_init();
+
+ /* Ensure SDRC pins are mux'd for self-refresh */
+ omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
+ omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
+}
+
+static void __init omap3_touchbook_map_io(void)
+{
+ omap2_set_globals_343x();
+ omap2_map_common_io();
+}
+
+MACHINE_START(TOUCHBOOK, "OMAP3 touchbook Board")
+ /* Maintainer: Gregoire Gentil - http://www.alwaysinnovating.com */
+ .phys_io = 0x48000000,
+ .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
+ .boot_params = 0x80000100,
+ .map_io = omap3_touchbook_map_io,
+ .init_irq = omap3_touchbook_init_irq,
+ .init_machine = omap3_touchbook_init,
+ .timer = &omap_timer,
+MACHINE_END
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 8/9] omap3: Defconfig file of Always Innovating OMAP3-based Touch Book
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
` (6 preceding siblings ...)
2009-12-09 0:51 ` [PATCH 7/9] omap3: Board file of Always Innovating OMAP3-based Touch Book Tony Lindgren
@ 2009-12-09 0:51 ` Tony Lindgren
2009-12-09 0:51 ` [PATCH 9/9] omap3: pandora: board file updates for .33 Tony Lindgren
8 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:51 UTC (permalink / raw)
To: linux-arm-kernel
From: Gregoire Gentil <gregoire@gentil.com>
Defconfig file of Always Innovating OMAP3-based Touch Book
Signed-off-by: Gregoire Gentil <gregoire@gentil.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/configs/omap3_touchbook_defconfig | 2431 ++++++++++++++++++++++++++++
1 files changed, 2431 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/configs/omap3_touchbook_defconfig
diff --git a/arch/arm/configs/omap3_touchbook_defconfig b/arch/arm/configs/omap3_touchbook_defconfig
new file mode 100644
index 0000000..7c8515e
--- /dev/null
+++ b/arch/arm/configs/omap3_touchbook_defconfig
@@ -0,0 +1,2431 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.32-rc8
+# Fri Dec 4 16:02:17 2009
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_ARCH_HAS_CPUFREQ=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_OPROFILE_ARMV7=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+# CONFIG_SYSCTL_SYSCALL is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+# CONFIG_ELF_CORE is not set
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_PROFILING=y
+CONFIG_TRACEPOINTS=y
+CONFIG_OPROFILE=y
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
+CONFIG_SLOW_WORK=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+CONFIG_FREEZER=y
+
+#
+# System Type
+#
+CONFIG_MMU=y
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_NOMADIK is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+CONFIG_ARCH_OMAP=y
+# CONFIG_ARCH_BCMRING is not set
+
+#
+# TI OMAP Implementations
+#
+CONFIG_ARCH_OMAP_OTG=y
+# CONFIG_ARCH_OMAP1 is not set
+# CONFIG_ARCH_OMAP2 is not set
+CONFIG_ARCH_OMAP3=y
+# CONFIG_ARCH_OMAP4 is not set
+
+#
+# OMAP Feature Selections
+#
+# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
+# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
+CONFIG_OMAP_RESET_CLOCKS=y
+# CONFIG_OMAP_MUX is not set
+CONFIG_OMAP_MCBSP=y
+# CONFIG_OMAP_MBOX_FWK is not set
+# CONFIG_OMAP_MPU_TIMER is not set
+CONFIG_OMAP_32K_TIMER=y
+CONFIG_OMAP_32K_TIMER_HZ=128
+CONFIG_OMAP_DM_TIMER=y
+# CONFIG_OMAP_LL_DEBUG_UART1 is not set
+# CONFIG_OMAP_LL_DEBUG_UART2 is not set
+CONFIG_OMAP_LL_DEBUG_UART3=y
+# CONFIG_OMAP_LL_DEBUG_NONE is not set
+# CONFIG_OMAP_PM_NONE is not set
+CONFIG_OMAP_PM_NOOP=y
+CONFIG_ARCH_OMAP34XX=y
+CONFIG_ARCH_OMAP3430=y
+
+#
+# OMAP Board Type
+#
+# CONFIG_MACH_OMAP3_BEAGLE is not set
+# CONFIG_MACH_OMAP_LDP is not set
+# CONFIG_MACH_OVERO is not set
+# CONFIG_MACH_OMAP3EVM is not set
+# CONFIG_MACH_OMAP3517EVM is not set
+# CONFIG_MACH_OMAP3_PANDORA is not set
+CONFIG_MACH_OMAP3_TOUCHBOOK=y
+# CONFIG_MACH_OMAP_3430SDP is not set
+# CONFIG_MACH_NOKIA_RX51 is not set
+# CONFIG_MACH_OMAP_ZOOM2 is not set
+# CONFIG_MACH_OMAP_ZOOM3 is not set
+# CONFIG_MACH_CM_T35 is not set
+# CONFIG_MACH_IGEP0020 is not set
+# CONFIG_MACH_OMAP_3630SDP is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_V7=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_HAS_ASID=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+CONFIG_ARM_THUMBEE=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_HAS_TLS_REG=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+# CONFIG_ARM_ERRATA_430973 is not set
+# CONFIG_ARM_ERRATA_458693 is not set
+# CONFIG_ARM_ERRATA_460075 is not set
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
+CONFIG_PREEMPT=y
+CONFIG_HZ=128
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_LEDS=y
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE=" debug "
+# CONFIG_XIP_KERNEL is not set
+CONFIG_KEXEC=y
+CONFIG_ATAGS_PROC=y
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_VFP=y
+CONFIG_VFPv3=y
+CONFIG_NEON=y
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+CONFIG_HAVE_AOUT=y
+CONFIG_BINFMT_AOUT=m
+CONFIG_BINFMT_MISC=y
+
+#
+# Power management options
+#
+CONFIG_PM=y
+CONFIG_PM_DEBUG=y
+# CONFIG_PM_VERBOSE is not set
+CONFIG_CAN_PM_TRACE=y
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+# CONFIG_PM_TEST_SUSPEND is not set
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
+# CONFIG_PM_RUNTIME is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE=m
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET_XFRM_TUNNEL=m
+CONFIG_INET_TUNNEL=m
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_LRO=y
+CONFIG_INET_DIAG=m
+CONFIG_INET_TCP_DIAG=m
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_TCP_CONG_BIC=m
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_TCP_CONG_WESTWOOD=m
+CONFIG_TCP_CONG_HTCP=m
+CONFIG_TCP_CONG_HSTCP=m
+CONFIG_TCP_CONG_HYBLA=m
+CONFIG_TCP_CONG_VEGAS=m
+CONFIG_TCP_CONG_SCALABLE=m
+CONFIG_TCP_CONG_LP=m
+CONFIG_TCP_CONG_VENO=m
+CONFIG_TCP_CONG_YEAH=m
+CONFIG_TCP_CONG_ILLINOIS=m
+# CONFIG_DEFAULT_BIC is not set
+CONFIG_DEFAULT_CUBIC=y
+# CONFIG_DEFAULT_HTCP is not set
+# CONFIG_DEFAULT_VEGAS is not set
+# CONFIG_DEFAULT_WESTWOOD is not set
+# CONFIG_DEFAULT_RENO is not set
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=m
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_IPV6_OPTIMISTIC_DAD is not set
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_INET6_XFRM_TUNNEL=m
+CONFIG_INET6_TUNNEL=m
+CONFIG_INET6_XFRM_MODE_TRANSPORT=m
+CONFIG_INET6_XFRM_MODE_TUNNEL=m
+CONFIG_INET6_XFRM_MODE_BEET=m
+CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
+CONFIG_IPV6_SIT=m
+CONFIG_IPV6_NDISC_NODETYPE=y
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_IPV6_MROUTE=y
+# CONFIG_IPV6_PIMSM_V2 is not set
+# CONFIG_NETWORK_SECMARK is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
+CONFIG_BRIDGE_NETFILTER=y
+
+#
+# Core Netfilter Configuration
+#
+CONFIG_NETFILTER_NETLINK=m
+CONFIG_NETFILTER_NETLINK_QUEUE=m
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CT_ACCT=y
+CONFIG_NF_CONNTRACK_MARK=y
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CT_PROTO_DCCP=m
+CONFIG_NF_CT_PROTO_GRE=m
+CONFIG_NF_CT_PROTO_SCTP=m
+CONFIG_NF_CT_PROTO_UDPLITE=m
+CONFIG_NF_CONNTRACK_AMANDA=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_H323=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_NETBIOS_NS=m
+CONFIG_NF_CONNTRACK_PPTP=m
+CONFIG_NF_CONNTRACK_SANE=m
+CONFIG_NF_CONNTRACK_SIP=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NF_CT_NETLINK=m
+# CONFIG_NETFILTER_TPROXY is not set
+CONFIG_NETFILTER_XTABLES=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
+CONFIG_NETFILTER_XT_TARGET_HL=m
+# CONFIG_NETFILTER_XT_TARGET_LED is not set
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+# CONFIG_NETFILTER_XT_TARGET_NOTRACK is not set
+CONFIG_NETFILTER_XT_TARGET_RATEEST=m
+# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set
+# CONFIG_NETFILTER_XT_MATCH_CLUSTER is not set
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_HL=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
+CONFIG_NETFILTER_XT_MATCH_U32=m
+# CONFIG_NETFILTER_XT_MATCH_OSF is not set
+CONFIG_IP_VS=m
+CONFIG_IP_VS_IPV6=y
+CONFIG_IP_VS_DEBUG=y
+CONFIG_IP_VS_TAB_BITS=12
+
+#
+# IPVS transport protocol load balancing support
+#
+CONFIG_IP_VS_PROTO_TCP=y
+CONFIG_IP_VS_PROTO_UDP=y
+CONFIG_IP_VS_PROTO_AH_ESP=y
+CONFIG_IP_VS_PROTO_ESP=y
+CONFIG_IP_VS_PROTO_AH=y
+
+#
+# IPVS scheduler
+#
+CONFIG_IP_VS_RR=m
+CONFIG_IP_VS_WRR=m
+CONFIG_IP_VS_LC=m
+CONFIG_IP_VS_WLC=m
+CONFIG_IP_VS_LBLC=m
+CONFIG_IP_VS_LBLCR=m
+CONFIG_IP_VS_DH=m
+CONFIG_IP_VS_SH=m
+CONFIG_IP_VS_SED=m
+CONFIG_IP_VS_NQ=m
+
+#
+# IPVS application helper
+#
+CONFIG_IP_VS_FTP=m
+
+#
+# IP: Netfilter Configuration
+#
+CONFIG_NF_DEFRAG_IPV4=m
+CONFIG_NF_CONNTRACK_IPV4=m
+CONFIG_NF_CONNTRACK_PROC_COMPAT=y
+CONFIG_IP_NF_QUEUE=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_NF_NAT=m
+CONFIG_NF_NAT_NEEDED=y
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_TARGET_NETMAP=m
+CONFIG_IP_NF_TARGET_REDIRECT=m
+CONFIG_NF_NAT_SNMP_BASIC=m
+CONFIG_NF_NAT_PROTO_DCCP=m
+CONFIG_NF_NAT_PROTO_GRE=m
+CONFIG_NF_NAT_PROTO_UDPLITE=m
+CONFIG_NF_NAT_PROTO_SCTP=m
+CONFIG_NF_NAT_FTP=m
+CONFIG_NF_NAT_IRC=m
+CONFIG_NF_NAT_TFTP=m
+CONFIG_NF_NAT_AMANDA=m
+CONFIG_NF_NAT_PPTP=m
+CONFIG_NF_NAT_H323=m
+CONFIG_NF_NAT_SIP=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+
+#
+# IPv6: Netfilter Configuration
+#
+CONFIG_NF_CONNTRACK_IPV6=m
+CONFIG_IP6_NF_QUEUE=m
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_TARGET_LOG=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+# CONFIG_BRIDGE_NF_EBTABLES is not set
+CONFIG_IP_DCCP=m
+CONFIG_INET_DCCP_DIAG=m
+
+#
+# DCCP CCIDs Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP_CCID2_DEBUG is not set
+CONFIG_IP_DCCP_CCID3=y
+# CONFIG_IP_DCCP_CCID3_DEBUG is not set
+CONFIG_IP_DCCP_CCID3_RTO=100
+CONFIG_IP_DCCP_TFRC_LIB=y
+
+#
+# DCCP Kernel Hacking
+#
+# CONFIG_IP_DCCP_DEBUG is not set
+CONFIG_IP_SCTP=m
+# CONFIG_SCTP_DBG_MSG is not set
+# CONFIG_SCTP_DBG_OBJCNT is not set
+# CONFIG_SCTP_HMAC_NONE is not set
+# CONFIG_SCTP_HMAC_SHA1 is not set
+CONFIG_SCTP_HMAC_MD5=y
+# CONFIG_RDS is not set
+CONFIG_TIPC=m
+# CONFIG_TIPC_ADVANCED is not set
+# CONFIG_TIPC_DEBUG is not set
+CONFIG_ATM=m
+CONFIG_ATM_CLIP=m
+# CONFIG_ATM_CLIP_NO_ICMP is not set
+CONFIG_ATM_LANE=m
+CONFIG_ATM_MPOA=m
+CONFIG_ATM_BR2684=m
+# CONFIG_ATM_BR2684_IPFILTER is not set
+CONFIG_STP=m
+CONFIG_GARP=m
+CONFIG_BRIDGE=m
+# CONFIG_NET_DSA is not set
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+# CONFIG_DECNET is not set
+CONFIG_LLC=m
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+CONFIG_WAN_ROUTER=m
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+CONFIG_NET_SCHED=y
+
+#
+# Queueing/Scheduling
+#
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_ATM=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_MULTIQ=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_DRR=m
+
+#
+# Classification
+#
+CONFIG_NET_CLS=y
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_ROUTE=y
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_CLS_U32_PERF=y
+CONFIG_CLS_U32_MARK=y
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_FLOW=m
+# CONFIG_NET_EMATCH is not set
+# CONFIG_NET_CLS_ACT is not set
+CONFIG_NET_CLS_IND=y
+CONFIG_NET_SCH_FIFO=y
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_DROP_MONITOR is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+CONFIG_BT=y
+CONFIG_BT_L2CAP=y
+CONFIG_BT_SCO=y
+CONFIG_BT_RFCOMM=y
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=y
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=y
+
+#
+# Bluetooth device drivers
+#
+CONFIG_BT_HCIBTUSB=y
+CONFIG_BT_HCIBTSDIO=y
+CONFIG_BT_HCIUART=y
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIUART_LL=y
+CONFIG_BT_HCIBCM203X=y
+CONFIG_BT_HCIBPA10X=y
+CONFIG_BT_HCIBFUSB=y
+# CONFIG_BT_HCIVHCI is not set
+# CONFIG_BT_MRVL is not set
+CONFIG_AF_RXRPC=m
+# CONFIG_AF_RXRPC_DEBUG is not set
+# CONFIG_RXKAD is not set
+CONFIG_FIB_RULES=y
+CONFIG_WIRELESS=y
+CONFIG_CFG80211=m
+# CONFIG_NL80211_TESTMODE is not set
+# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
+# CONFIG_CFG80211_REG_DEBUG is not set
+CONFIG_CFG80211_DEFAULT_PS=y
+CONFIG_CFG80211_DEFAULT_PS_VALUE=1
+# CONFIG_CFG80211_DEBUGFS is not set
+# CONFIG_WIRELESS_OLD_REGULATORY is not set
+CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
+CONFIG_LIB80211=y
+# CONFIG_LIB80211_DEBUG is not set
+CONFIG_MAC80211=m
+CONFIG_MAC80211_RC_PID=y
+# CONFIG_MAC80211_RC_MINSTREL is not set
+CONFIG_MAC80211_RC_DEFAULT_PID=y
+# CONFIG_MAC80211_RC_DEFAULT_MINSTREL is not set
+CONFIG_MAC80211_RC_DEFAULT="pid"
+# CONFIG_MAC80211_MESH is not set
+# CONFIG_MAC80211_LEDS is not set
+# CONFIG_MAC80211_DEBUGFS is not set
+# CONFIG_MAC80211_DEBUG_MENU is not set
+CONFIG_WIMAX=m
+CONFIG_WIMAX_DEBUG_LEVEL=8
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_OMAP2=y
+CONFIG_MTD_NAND_OMAP_PREFETCH=y
+# CONFIG_MTD_NAND_OMAP_PREFETCH_DMA is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+CONFIG_MTD_NAND_PLATFORM=y
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=16384
+# CONFIG_BLK_DEV_XIP is not set
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_CDROM_PKTCDVD_BUFFERS=8
+# CONFIG_CDROM_PKTCDVD_WCACHE is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+CONFIG_EEPROM_93CX6=y
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+CONFIG_RAID_ATTRS=m
+CONFIG_SCSI=y
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+CONFIG_BLK_DEV_SR=y
+CONFIG_BLK_DEV_SR_VENDOR=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_CHR_DEV_SCH=m
+CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+CONFIG_SCSI_ISCSI_ATTRS=m
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+CONFIG_SCSI_LOWLEVEL=y
+CONFIG_ISCSI_TCP=m
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+# CONFIG_ATA is not set
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_RAID6_PQ=m
+# CONFIG_ASYNC_RAID6_TEST is not set
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+# CONFIG_DM_DEBUG is not set
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+# CONFIG_DM_LOG_USERSPACE is not set
+CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+# CONFIG_DM_MULTIPATH_QL is not set
+# CONFIG_DM_MULTIPATH_ST is not set
+CONFIG_DM_DELAY=m
+# CONFIG_DM_UEVENT is not set
+CONFIG_NETDEVICES=y
+CONFIG_DUMMY=m
+CONFIG_BONDING=m
+CONFIG_MACVLAN=m
+CONFIG_EQUALIZER=m
+CONFIG_TUN=m
+CONFIG_VETH=m
+# CONFIG_NET_ETHERNET is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+CONFIG_WLAN=y
+# CONFIG_WLAN_PRE80211 is not set
+CONFIG_WLAN_80211=y
+# CONFIG_LIBERTAS is not set
+# CONFIG_LIBERTAS_THINFIRM is not set
+# CONFIG_AT76C50X_USB is not set
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_USB_NET_RNDIS_WLAN is not set
+# CONFIG_RTL8187 is not set
+# CONFIG_MAC80211_HWSIM is not set
+# CONFIG_P54_COMMON is not set
+# CONFIG_ATH_COMMON is not set
+# CONFIG_HOSTAP is not set
+# CONFIG_B43 is not set
+# CONFIG_B43LEGACY is not set
+# CONFIG_ZD1211RW is not set
+# CONFIG_RT2X00 is not set
+# CONFIG_WL12XX is not set
+# CONFIG_IWM is not set
+
+#
+# WiMAX Wireless Broadband devices
+#
+# CONFIG_WIMAX_I2400M_USB is not set
+# CONFIG_WIMAX_I2400M_SDIO is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+# CONFIG_ATM_DRIVERS is not set
+CONFIG_PPP=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_MPPE=m
+CONFIG_PPPOE=m
+# CONFIG_PPPOATM is not set
+CONFIG_PPPOL2TP=m
+# CONFIG_SLIP is not set
+CONFIG_SLHC=m
+CONFIG_NETCONSOLE=m
+CONFIG_NETCONSOLE_DYNAMIC=y
+CONFIG_NETPOLL=y
+CONFIG_NETPOLL_TRAP=y
+CONFIG_NET_POLL_CONTROLLER=y
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+CONFIG_INPUT_FF_MEMLESS=y
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_QT2160 is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_TWL4030 is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_SENTELIC is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
+# CONFIG_MOUSE_BCM5974 is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_GPIO is not set
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MCS5000 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+CONFIG_INPUT_MISC=y
+# CONFIG_INPUT_ATI_REMOTE is not set
+# CONFIG_INPUT_ATI_REMOTE2 is not set
+# CONFIG_INPUT_KEYSPAN_REMOTE is not set
+# CONFIG_INPUT_POWERMATE is not set
+# CONFIG_INPUT_YEALINK is not set
+# CONFIG_INPUT_CM109 is not set
+CONFIG_INPUT_TWL4030_PWRBUTTON=y
+CONFIG_INPUT_UINPUT=y
+# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=32
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_DETECT_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+CONFIG_HW_RANDOM=y
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_OMAP=y
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_OMAP24XX=y
+
+#
+# SPI Protocol Masters
+#
+CONFIG_SPI_SPIDEV=y
+# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+CONFIG_GPIO_TWL4030=y
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
+# CONFIG_W1 is not set
+CONFIG_POWER_SUPPLY=y
+# CONFIG_POWER_SUPPLY_DEBUG is not set
+# CONFIG_PDA_POWER is not set
+# CONFIG_BATTERY_DS2760 is not set
+# CONFIG_BATTERY_DS2782 is not set
+CONFIG_BATTERY_BQ27x00=y
+# CONFIG_BATTERY_MAX17040 is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADCXX is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM70 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1111 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_TMP421 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_SENSORS_LIS3_SPI is not set
+CONFIG_THERMAL=y
+CONFIG_THERMAL_HWMON=y
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_OMAP_WATCHDOG=y
+# CONFIG_TWL4030_WATCHDOG is not set
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+CONFIG_TWL4030_CORE=y
+# CONFIG_TWL4030_POWER is not set
+# CONFIG_TWL4030_CODEC is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+CONFIG_REGULATOR_TWL4030=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_TPS65023 is not set
+# CONFIG_REGULATOR_TPS6507X is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+# CONFIG_FB_CFB_FILLRECT is not set
+# CONFIG_FB_CFB_COPYAREA is not set
+# CONFIG_FB_CFB_IMAGEBLIT is not set
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_FB_OMAP is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_GENERIC=y
+
+#
+# Display device support
+#
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_HWDEP=y
+CONFIG_SND_RAWMIDI=y
+CONFIG_SND_JACK=y
+CONFIG_SND_SEQUENCER=m
+# CONFIG_SND_SEQ_DUMMY is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+CONFIG_SND_PCM_OSS_PLUGINS=y
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_HRTIMER=m
+CONFIG_SND_SEQ_HRTIMER_DEFAULT=y
+# CONFIG_SND_DYNAMIC_MINORS is not set
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+CONFIG_SND_RAWMIDI_SEQ=m
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
+CONFIG_SND_DRIVERS=y
+# CONFIG_SND_DUMMY is not set
+# CONFIG_SND_VIRMIDI is not set
+# CONFIG_SND_MTPAV is not set
+# CONFIG_SND_SERIAL_U16550 is not set
+# CONFIG_SND_MPU401 is not set
+# CONFIG_SND_ARM is not set
+CONFIG_SND_SPI=y
+CONFIG_SND_USB=y
+CONFIG_SND_USB_AUDIO=y
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_CAIAQ_INPUT=y
+CONFIG_SND_SOC=y
+CONFIG_SND_OMAP_SOC=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
+# CONFIG_SOUND_PRIME is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HIDRAW is not set
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+# CONFIG_HID_PID is not set
+# CONFIG_USB_HIDDEV is not set
+
+#
+# Special HID drivers
+#
+# CONFIG_HID_A4TECH is not set
+# CONFIG_HID_APPLE is not set
+# CONFIG_HID_BELKIN is not set
+# CONFIG_HID_CHERRY is not set
+# CONFIG_HID_CHICONY is not set
+# CONFIG_HID_CYPRESS is not set
+# CONFIG_HID_DRAGONRISE is not set
+# CONFIG_HID_EZKEY is not set
+# CONFIG_HID_KYE is not set
+# CONFIG_HID_GYRATION is not set
+# CONFIG_HID_TWINHAN is not set
+# CONFIG_HID_KENSINGTON is not set
+# CONFIG_HID_LOGITECH is not set
+# CONFIG_HID_MICROSOFT is not set
+# CONFIG_HID_MONTEREY is not set
+# CONFIG_HID_NTRIG is not set
+# CONFIG_HID_PANTHERLORD is not set
+# CONFIG_HID_PETALYNX is not set
+# CONFIG_HID_SAMSUNG is not set
+# CONFIG_HID_SONY is not set
+# CONFIG_HID_SUNPLUS is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
+# CONFIG_HID_TOPSEED is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_WACOM is not set
+# CONFIG_HID_ZEROPLUS is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+CONFIG_USB_SUSPEND=y
+CONFIG_USB_OTG=y
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+CONFIG_USB_MON=y
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_OXU210HP_HCD=y
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
+# CONFIG_USB_OHCI_HCD is not set
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_SOC=y
+
+#
+# OMAP 343x high speed USB support
+#
+# CONFIG_USB_MUSB_HOST is not set
+# CONFIG_USB_MUSB_PERIPHERAL is not set
+CONFIG_USB_MUSB_OTG=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
+CONFIG_USB_MUSB_HDRC_HCD=y
+# CONFIG_MUSB_PIO_ONLY is not set
+CONFIG_USB_INVENTRA_DMA=y
+# CONFIG_USB_TI_CPPI_DMA is not set
+# CONFIG_USB_MUSB_DEBUG is not set
+
+#
+# USB Device Class drivers
+#
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
+CONFIG_USB_WDM=m
+CONFIG_USB_TMC=m
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+CONFIG_USB_SERIAL=m
+CONFIG_USB_EZUSB=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_CH341=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+# CONFIG_USB_SERIAL_CP210X is not set
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_FUNSOFT=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_IUU=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KEYSPAN_MPR=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19=y
+CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
+CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
+CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OTI6858=m
+# CONFIG_USB_SERIAL_QUALCOMM is not set
+CONFIG_USB_SERIAL_SPCP8X5=m
+CONFIG_USB_SERIAL_HP4X=m
+CONFIG_USB_SERIAL_SAFE=m
+# CONFIG_USB_SERIAL_SAFE_PADDED is not set
+CONFIG_USB_SERIAL_SIEMENS_MPI=m
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+# CONFIG_USB_SERIAL_SYMBOL is not set
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_SERIAL_OPTICON=m
+CONFIG_USB_SERIAL_DEBUG=m
+
+#
+# USB Miscellaneous drivers
+#
+CONFIG_USB_EMI62=m
+CONFIG_USB_EMI26=m
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+CONFIG_USB_SISUSBVGA=m
+CONFIG_USB_SISUSBVGA_CON=y
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+CONFIG_USB_TEST=m
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+# CONFIG_USB_ATM is not set
+CONFIG_USB_GADGET=m
+# CONFIG_USB_GADGET_DEBUG is not set
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_DEBUG_FS=y
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
+# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+CONFIG_USB_GADGET_DUALSPEED=y
+CONFIG_USB_ZERO=m
+CONFIG_USB_ZERO_HNPTEST=y
+# CONFIG_USB_AUDIO is not set
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_RNDIS=y
+# CONFIG_USB_ETH_EEM is not set
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_FILE_STORAGE=m
+# CONFIG_USB_FILE_STORAGE_TEST is not set
+CONFIG_USB_G_SERIAL=m
+CONFIG_USB_MIDI_GADGET=m
+CONFIG_USB_G_PRINTER=m
+CONFIG_USB_CDC_COMPOSITE=m
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+CONFIG_USB_GPIO_VBUS=y
+# CONFIG_ISP1301_OMAP is not set
+CONFIG_TWL4030_USB=y
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+CONFIG_MMC_UNSAFE_RESUME=y
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+CONFIG_SDIO_UART=y
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_OMAP is not set
+CONFIG_MMC_OMAP_HS=y
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
+CONFIG_MMC_SPI=m
+# CONFIG_MEMSTICK is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP3944 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=m
+# CONFIG_LEDS_TRIGGER_GPIO is not set
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+CONFIG_RTC_DRV_TWL4030=y
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+CONFIG_UIO=m
+CONFIG_UIO_PDRV=m
+CONFIG_UIO_PDRV_GENIRQ=m
+# CONFIG_UIO_SMX is not set
+# CONFIG_UIO_SERCOS3 is not set
+
+#
+# TI VLYNQ
+#
+CONFIG_STAGING=y
+# CONFIG_STAGING_EXCLUDE_BUILD is not set
+# CONFIG_USB_IP_COMMON is not set
+# CONFIG_W35UND is not set
+# CONFIG_PRISM2_USB is not set
+# CONFIG_ECHO is not set
+# CONFIG_OTUS is not set
+# CONFIG_COMEDI is not set
+# CONFIG_ASUS_OLED is not set
+# CONFIG_INPUT_MIMIO is not set
+# CONFIG_TRANZPORT is not set
+
+#
+# Android
+#
+
+#
+# Qualcomm MSM Camera And Video
+#
+
+#
+# Camera Sensor Selection
+#
+# CONFIG_INPUT_GPIO is not set
+# CONFIG_DST is not set
+# CONFIG_POHMELFS is not set
+# CONFIG_PLAN9AUTH is not set
+# CONFIG_LINE6_USB is not set
+# CONFIG_USB_SERIAL_QUATECH2 is not set
+# CONFIG_USB_SERIAL_QUATECH_USB2 is not set
+# CONFIG_VT6656 is not set
+# CONFIG_FB_UDL is not set
+
+#
+# RAR Register Driver
+#
+# CONFIG_RAR_REGISTER is not set
+# CONFIG_IIO is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+# CONFIG_EXT3_FS_XATTR is not set
+CONFIG_EXT4_FS=m
+CONFIG_EXT4_FS_XATTR=y
+# CONFIG_EXT4_FS_POSIX_ACL is not set
+# CONFIG_EXT4_FS_SECURITY is not set
+# CONFIG_EXT4_DEBUG is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_JBD2=m
+# CONFIG_JBD2_DEBUG is not set
+CONFIG_FS_MBCACHE=m
+CONFIG_REISERFS_FS=m
+# CONFIG_REISERFS_CHECK is not set
+CONFIG_REISERFS_PROC_INFO=y
+CONFIG_REISERFS_FS_XATTR=y
+# CONFIG_REISERFS_FS_POSIX_ACL is not set
+# CONFIG_REISERFS_FS_SECURITY is not set
+CONFIG_JFS_FS=m
+# CONFIG_JFS_POSIX_ACL is not set
+# CONFIG_JFS_SECURITY is not set
+# CONFIG_JFS_DEBUG is not set
+# CONFIG_JFS_STATISTICS is not set
+CONFIG_FS_POSIX_ACL=y
+CONFIG_XFS_FS=m
+# CONFIG_XFS_QUOTA is not set
+# CONFIG_XFS_POSIX_ACL is not set
+# CONFIG_XFS_RT is not set
+# CONFIG_XFS_DEBUG is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_QUOTA=y
+# CONFIG_QUOTA_NETLINK_INTERFACE is not set
+CONFIG_PRINT_QUOTA_WARNING=y
+CONFIG_QUOTA_TREE=y
+# CONFIG_QFMT_V1 is not set
+CONFIG_QFMT_V2=y
+CONFIG_QUOTACTL=y
+# CONFIG_AUTOFS_FS is not set
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=y
+# CONFIG_CUSE is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_UDF_NLS=y
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_NTFS_FS=m
+# CONFIG_NTFS_DEBUG is not set
+CONFIG_NTFS_RW=y
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_CONFIGFS_FS=m
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_ECRYPT_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_FS_POSIX_ACL=y
+CONFIG_JFFS2_FS_SECURITY=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
+CONFIG_JFFS2_RUBIN=y
+# CONFIG_JFFS2_CMODE_NONE is not set
+# CONFIG_JFFS2_CMODE_PRIORITY is not set
+# CONFIG_JFFS2_CMODE_SIZE is not set
+CONFIG_JFFS2_CMODE_FAVOURLZO=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_XATTR=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
+# CONFIG_CRAMFS is not set
+CONFIG_SQUASHFS=y
+# CONFIG_SQUASHFS_EMBEDDED is not set
+CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V2_ACL=y
+CONFIG_NFSD_V3=y
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_EXPORTFS=m
+CONFIG_NFS_ACL_SUPPORT=m
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+CONFIG_CIFS=m
+CONFIG_CIFS_STATS=y
+CONFIG_CIFS_STATS2=y
+# CONFIG_CIFS_WEAK_PW_HASH is not set
+# CONFIG_CIFS_UPCALL is not set
+# CONFIG_CIFS_XATTR is not set
+# CONFIG_CIFS_DEBUG2 is not set
+# CONFIG_CIFS_DFS_UPCALL is not set
+CONFIG_CIFS_EXPERIMENTAL=y
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+# CONFIG_LDM_PARTITION is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+CONFIG_EFI_PARTITION=y
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=y
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+CONFIG_SCHED_DEBUG=y
+CONFIG_SCHEDSTATS=y
+CONFIG_TIMER_STATS=y
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+CONFIG_DEBUG_PREEMPT=y
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+CONFIG_STACKTRACE=y
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_NOP_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_RING_BUFFER=y
+CONFIG_EVENT_TRACING=y
+CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
+CONFIG_TRACING=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_FTRACE=y
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_PREEMPT_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_BOOT_TRACER is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_RING_BUFFER_BENCHMARK is not set
+# CONFIG_DYNAMIC_DEBUG is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+CONFIG_ARM_UNWIND=y
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+CONFIG_KEYS=y
+# CONFIG_KEYS_DEBUG_PROC_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_XOR_BLOCKS=m
+CONFIG_ASYNC_CORE=m
+CONFIG_ASYNC_MEMCPY=m
+CONFIG_ASYNC_XOR=m
+CONFIG_ASYNC_PQ=m
+CONFIG_ASYNC_RAID6_RECOV=m
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_FIPS=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=m
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_GF128MUL=m
+CONFIG_CRYPTO_NULL=m
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_TEST=m
+
+#
+# Authenticated Encryption with Associated Data
+#
+CONFIG_CRYPTO_CCM=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_SEQIV=m
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CTR=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+
+#
+# Hash modes
+#
+CONFIG_CRYPTO_HMAC=m
+CONFIG_CRYPTO_XCBC=m
+# CONFIG_CRYPTO_VMAC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=y
+CONFIG_CRYPTO_GHASH=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_MICHAEL_MIC=y
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
+CONFIG_CRYPTO_SHA1=m
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+
+#
+# Ciphers
+#
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SALSA20=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_TWOFISH_COMMON=m
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ZLIB is not set
+CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=m
+CONFIG_CRYPTO_HW=y
+CONFIG_BINARY_PRINTF=y
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=y
+CONFIG_CRC16=y
+CONFIG_CRC_T10DIF=y
+CONFIG_CRC_ITU_T=y
+CONFIG_CRC32=y
+CONFIG_CRC7=y
+CONFIG_LIBCRC32C=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_TEXTSEARCH=y
+CONFIG_TEXTSEARCH_KMP=m
+CONFIG_TEXTSEARCH_BM=m
+CONFIG_TEXTSEARCH_FSM=m
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH 9/9] omap3: pandora: board file updates for .33
2009-12-09 0:49 [PATCH 0/9] Few more omap patches for v2.6.33 merge window Tony Lindgren
` (7 preceding siblings ...)
2009-12-09 0:51 ` [PATCH 8/9] omap3: Defconfig " Tony Lindgren
@ 2009-12-09 0:51 ` Tony Lindgren
8 siblings, 0 replies; 11+ messages in thread
From: Tony Lindgren @ 2009-12-09 0:51 UTC (permalink / raw)
To: linux-arm-kernel
From: Grazvydas Ignotas <notasas@gmail.com>
Pandora board file updates:
- change keycodes of game buttons
it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
the older DSS driver was never functional on l-o or mainline
kernels due to missing panel driver, so remove unneeded
pandora_lcd platform_device. This also removes last OMAP_TAG
from the board file.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3pandora.c | 26 +++++---------------------
1 files changed, 5 insertions(+), 21 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index c1cc99c..6f6c601 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -98,10 +98,10 @@ static struct gpio_keys_button pandora_gpio_keys[] = {
GPIO_BUTTON_LOW(103, KEY_DOWN, "down"),
GPIO_BUTTON_LOW(96, KEY_LEFT, "left"),
GPIO_BUTTON_LOW(98, KEY_RIGHT, "right"),
- GPIO_BUTTON_LOW(111, BTN_A, "a"),
- GPIO_BUTTON_LOW(106, BTN_B, "b"),
- GPIO_BUTTON_LOW(109, BTN_X, "x"),
- GPIO_BUTTON_LOW(101, BTN_Y, "y"),
+ GPIO_BUTTON_LOW(109, KEY_KP1, "game 1"),
+ GPIO_BUTTON_LOW(111, KEY_KP2, "game 2"),
+ GPIO_BUTTON_LOW(106, KEY_KP3, "game 3"),
+ GPIO_BUTTON_LOW(101, KEY_KP4, "game 4"),
GPIO_BUTTON_LOW(102, BTN_TL, "l"),
GPIO_BUTTON_LOW(97, BTN_TL2, "l2"),
GPIO_BUTTON_LOW(105, BTN_TR, "r"),
@@ -315,7 +315,7 @@ static int __init omap3pandora_i2c_init(void)
omap_register_i2c_bus(1, 2600, omap3pandora_i2c_boardinfo,
ARRAY_SIZE(omap3pandora_i2c_boardinfo));
/* i2c2 pins are not connected */
- omap_register_i2c_bus(3, 400, NULL, 0);
+ omap_register_i2c_bus(3, 100, NULL, 0);
return 0;
}
@@ -368,23 +368,8 @@ static struct spi_board_info omap3pandora_spi_board_info[] __initdata = {
}
};
-static struct platform_device omap3pandora_lcd_device = {
- .name = "pandora_lcd",
- .id = -1,
-};
-
-static struct omap_lcd_config omap3pandora_lcd_config __initdata = {
- .ctrl_name = "internal",
-};
-
-static struct omap_board_config_kernel omap3pandora_config[] __initdata = {
- { OMAP_TAG_LCD, &omap3pandora_lcd_config },
-};
-
static void __init omap3pandora_init_irq(void)
{
- omap_board_config = omap3pandora_config;
- omap_board_config_size = ARRAY_SIZE(omap3pandora_config);
omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
omap_init_irq();
@@ -392,7 +377,6 @@ static void __init omap3pandora_init_irq(void)
}
static struct platform_device *omap3pandora_devices[] __initdata = {
- &omap3pandora_lcd_device,
&pandora_leds_gpio,
&pandora_keys_gpio,
};
^ permalink raw reply related [flat|nested] 11+ messages in thread