From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 01/14] omap3: cm-t35: add mux initialization
Date: Fri, 11 Dec 2009 15:52:28 -0800 [thread overview]
Message-ID: <20091211235228.3189.82115.stgit@localhost> (raw)
In-Reply-To: <20091211234919.3189.95607.stgit@localhost>
From: Mike Rapoport <mike@compulab.co.il>
CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/Kconfig | 1
arch/arm/mach-omap2/board-cm-t35.c | 96 +++++++++++++++++++++++++++++++++---
2 files changed, 90 insertions(+), 7 deletions(-)
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 06dc64d..76c11ee 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -135,6 +135,7 @@ config MACH_CM_T35
bool "CompuLab CM-T35 module"
depends on ARCH_OMAP3 && ARCH_OMAP34XX
select OMAP_PACKAGE_CUS
+ select OMAP_MUX
config MACH_IGEP0020
bool "IGEP0020"
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index 507c922..1591aae 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -482,13 +482,98 @@ static void __init cm_t35_map_io(void)
omap2_map_common_io();
}
-#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ /* nCS and IRQ for CM-T35 ethernet */
+ OMAP3_MUX(GPMC_NCS5, OMAP_MUX_MODE0),
+ OMAP3_MUX(UART3_CTS_RCTX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
+
+ /* nCS and IRQ for SB-T35 ethernet */
+ OMAP3_MUX(GPMC_NCS4, OMAP_MUX_MODE0),
+ OMAP3_MUX(GPMC_WAIT3, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
+
+ /* PENDOWN GPIO */
+ OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
+
+ /* mUSB */
+ OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+
+ /* MMC 2 */
+ OMAP3_MUX(SDMMC2_DAT4, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(SDMMC2_DAT6, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(SDMMC2_DAT7, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
+
+ /* McSPI 1 */
+ OMAP3_MUX(MCSPI1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCSPI1_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCSPI1_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCSPI1_CS0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
+
+ /* McSPI 4 */
+ OMAP3_MUX(MCBSP1_CLKR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
+
+ /* McBSP 2 */
+ OMAP3_MUX(MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCBSP2_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCBSP2_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+ OMAP3_MUX(MCBSP2_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+
+ /* serial ports */
+ OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
+ OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+
+ /* DSS */
+ OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+ OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
+
+ /* TPS IRQ */
+ OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_WAKEUP_EN | \
+ OMAP_PIN_INPUT_PULLUP),
+
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
-#else
-#define board_mux NULL
-#endif
static void __init cm_t35_init(void)
{
@@ -501,9 +586,6 @@ static void __init cm_t35_init(void)
cm_t35_init_led();
usb_musb_init();
-
- omap_mux_init_signal("sys_nirq",
- OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
}
MACHINE_START(CM_T35, "Compulab CM-T35")
next prev parent reply other threads:[~2009-12-11 23:52 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-12-11 23:52 [PATCH 00/14] Mostly fixes for 2.6.33 Tony Lindgren
2009-12-11 23:52 ` Tony Lindgren [this message]
2009-12-11 23:52 ` [PATCH 02/14] OMAP3: serial - allow platforms specify which UARTs to initialize Tony Lindgren
2009-12-11 23:52 ` [PATCH 03/14] omap: Correcting GPMC_CONFIG1_DEVICETYPE_NAND Tony Lindgren
2009-12-11 23:53 ` [PATCH 04/14] omap: arch/arm/plat-omap/devices.c - sort alphabetically Tony Lindgren
2009-12-11 23:53 ` [PATCH 05/14] omap: header: remove unused data-type Tony Lindgren
2009-12-11 23:53 ` [PATCH 06/14] omap1: LCD_DMA: Use some define rather than a hexadecimal Tony Lindgren
2009-12-11 23:53 ` [PATCH 07/14] omap1: htcherald: Update defconfig to include mux support Tony Lindgren
2009-12-11 23:53 ` [PATCH 08/14] omap3: zoom2/3: make MMC slot work again Tony Lindgren
2009-12-11 23:54 ` [PATCH 09/14] omap3: rx51: Use wl1251 in SPI mode 3 Tony Lindgren
2009-12-11 23:54 ` [PATCH 10/14] omap3: id code detection 3525 vs 3515 Tony Lindgren
2009-12-11 23:54 ` [PATCH 11/14] omap3 : Enable TWL4030 Keypad for Zoom2 and Zoom3 boards Tony Lindgren
2009-12-11 23:54 ` [PATCH 12/14] omap3: Zoom2/3: Update hsmmc board config params Tony Lindgren
2009-12-12 0:09 ` [PATCH 13/14] omap: serial: fix non-empty uart fifo read abort Tony Lindgren
2009-12-12 0:10 ` [PATCH 14/14] omap3: Fix OMAP35XX_REV macros Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20091211235228.3189.82115.stgit@localhost \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).