[PATCH 00/19] omap-fixes for 2.6.34-rc1

[PATCH 00/19] omap-fixes for 2.6.34-rc1

[Tony Lindgren]

Hi all,

Here's some omap fixes for review.

I also threw in the n8x0 platform init for tusb6010 and
updated the defconfig as those were needed to fix and test
the tusb6010 for the DMA API changes as posted earlier.

Regards,

Tony

---

Aaro Koskinen (2):
      omap: pass the reboot command to the boot loader
      omap: mach-omap2/io.c: fix function declarations

Andrea Gelmini (1):
      omap: Checkpatch cleanup for blizzard.h

Andrew Clayton (1):
      ARM/OMAP: Remove the +x bit from a couple of source files

Enric Balletbo i Serra (1):
      omap3: Fix support for the LEDs connected to GPIO outputs on IGEP v2board

Felipe Balbi (1):
      omap2/3/4: ehci: avoid compiler error with touchbook

Francisco Alecrim (1):
      omap2: add USB initialization for tusb6010

Grazvydas Ignotas (1):
      omap3: pandora: add missing i2c3 board_info

Janusz Krzysztofik (1):
      omap: McBSP: Drop unnecessary status/error bit clearing on reg_cacheretrieved register values

Kevin Hilman (2):
      OMAP2: cpu_is_omap2*: fix compile-time removal of unused code
      OMAP4: fix temporary hacks that break multi-omap PM

Santosh Shilimkar (1):
      omap4: Fix build break by moving omap_smc1 into a separate .S

Suman Anna (1):
      omap2/3/4: mailbox: remove compiler warning

Thomas Weber (1):
      OMAP2: serial.c: Fix number of uarts in early_init

Tony Lindgren (4):
      omap3: Fix compile for Touch Book early_param
      omap2: Update n8x0 defconfig to test multi-omap and DMA api changes
      omap: Enable PM_RUNTIME in defconfigs to avoid USB compile errors
      omap: Fix gpio_resume_after_retention

Vaibhav Hiremath (1):
      omap: Add DSI regulator supply to OMAP3EVM board file


 arch/arm/configs/cm_t35_defconfig            |    2 
 arch/arm/configs/n770_defconfig              |    1 
 arch/arm/configs/n8x0_defconfig              |  160 +++++++++++++++++++++++---
 arch/arm/configs/omap3_beagle_defconfig      |    1 
 arch/arm/configs/omap3_defconfig             |    2 
 arch/arm/configs/omap3_evm_defconfig         |    1 
 arch/arm/configs/omap3_touchbook_defconfig   |    2 
 arch/arm/configs/omap_3430sdp_defconfig      |    1 
 arch/arm/configs/omap_3630sdp_defconfig      |    2 
 arch/arm/configs/omap_h2_1610_defconfig      |    1 
 arch/arm/configs/omap_zoom2_defconfig        |    1 
 arch/arm/configs/omap_zoom3_defconfig        |    2 
 arch/arm/configs/rx51_defconfig              |    1 
 arch/arm/mach-omap2/Makefile                 |    3 
 arch/arm/mach-omap2/board-3430sdp.c          |    2 
 arch/arm/mach-omap2/board-3630sdp.c          |    2 
 arch/arm/mach-omap2/board-4430sdp.c          |   26 ----
 arch/arm/mach-omap2/board-am3517evm.c        |    2 
 arch/arm/mach-omap2/board-cm-t35.c           |    2 
 arch/arm/mach-omap2/board-devkit8000.c       |    2 
 arch/arm/mach-omap2/board-igep0020.c         |   56 ++++++---
 arch/arm/mach-omap2/board-n8x0.c             |   98 ++++++++++++++++
 arch/arm/mach-omap2/board-omap3beagle.c      |    2 
 arch/arm/mach-omap2/board-omap3evm.c         |   18 ++-
 arch/arm/mach-omap2/board-omap3pandora.c     |   12 ++
 arch/arm/mach-omap2/board-omap3touchbook.c   |   12 +-
 arch/arm/mach-omap2/board-overo.c            |    2 
 arch/arm/mach-omap2/board-zoom-peripherals.c |    0 
 arch/arm/mach-omap2/board-zoom3.c            |    2 
 arch/arm/mach-omap2/clock2420_data.c         |    1 
 arch/arm/mach-omap2/io.c                     |   21 ++-
 arch/arm/mach-omap2/mailbox.c                |   12 +-
 arch/arm/mach-omap2/omap44xx-smc.S           |   32 +++++
 arch/arm/mach-omap2/prcm.c                   |    4 -
 arch/arm/mach-omap2/serial.c                 |   15 ++
 arch/arm/mach-omap2/usb-ehci.c               |    6 -
 arch/arm/plat-omap/gpio.c                    |   10 +-
 arch/arm/plat-omap/include/plat/blizzard.h   |    2 
 arch/arm/plat-omap/include/plat/cpu.h        |    8 +
 arch/arm/plat-omap/include/plat/prcm.h       |    2 
 arch/arm/plat-omap/include/plat/system.h     |    6 -
 arch/arm/plat-omap/include/plat/usb.h        |    2 
 arch/arm/plat-omap/mcbsp.c                   |   12 +-
 43 files changed, 414 insertions(+), 137 deletions(-)
 mode change 100755 => 100644 arch/arm/mach-omap2/board-3630sdp.c
 mode change 100755 => 100644 arch/arm/mach-omap2/board-zoom-peripherals.c
 create mode 100644 arch/arm/mach-omap2/omap44xx-smc.S

-- 
Signature

[PATCH 01/19] omap3: Fix compile for Touch Book early_param

[Tony Lindgren]

Commit 2b0d8c251b8876d530a6bf671eb5425838fa698a changed ARM to use
the common early_param code. Fix compile for Touch Book accordingly.

Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-omap3touchbook.c |   10 +++++-----
 1 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
index 3943d0f..2a5bf5c 100644
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ b/arch/arm/mach-omap2/board-omap3touchbook.c
@@ -518,14 +518,14 @@ static void omap3_touchbook_poweroff(void)
 	gpio_direction_output(TB_KILL_POWER_GPIO, 0);
 }
 
-static void __init early_touchbook_revision(char **p)
+static int __init early_touchbook_revision(char *p)
 {
-	if (!*p)
-		return;
+	if (!p)
+		return 0;
 
-	strict_strtoul(*p, 10, &touchbook_revision);
+	return strict_strtoul(p, 10, &touchbook_revision);
 }
-__early_param("tbr=", early_touchbook_revision);
+early_param("tbr", early_touchbook_revision);
 
 static struct omap_musb_board_data musb_board_data = {
 	.interface_type		= MUSB_INTERFACE_ULPI,

[PATCH 02/19] omap2/3/4: ehci: avoid compiler error with touchbook

[Tony Lindgren]

From: Felipe Balbi <felipe.balbi@nokia.com>

the early_param() call in board-omap3touchbook.c expands to:

static const char __setup_str_early_touchbook_revision[]
	__section(.init.rodata) _aligned(1) = tbr;
[...]

and we have a non-const variable being added to the
same section:

static struct ehci_hcd_omap_platform_data ehci_pdata
__section(.init.rodata);

because of that, gcc generates a section type conflict
which can (and actually should) be avoided by marking
const every variable marked with __initconst.

This patch fixes that for the ehci_hdc_omap_platform_data.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-3430sdp.c        |    2 +-
 arch/arm/mach-omap2/board-3630sdp.c        |    2 +-
 arch/arm/mach-omap2/board-am3517evm.c      |    2 +-
 arch/arm/mach-omap2/board-cm-t35.c         |    2 +-
 arch/arm/mach-omap2/board-devkit8000.c     |    2 +-
 arch/arm/mach-omap2/board-igep0020.c       |    2 +-
 arch/arm/mach-omap2/board-omap3beagle.c    |    2 +-
 arch/arm/mach-omap2/board-omap3evm.c       |    2 +-
 arch/arm/mach-omap2/board-omap3pandora.c   |    2 +-
 arch/arm/mach-omap2/board-omap3touchbook.c |    2 +-
 arch/arm/mach-omap2/board-overo.c          |    2 +-
 arch/arm/mach-omap2/board-zoom3.c          |    2 +-
 arch/arm/mach-omap2/usb-ehci.c             |    6 +++---
 arch/arm/plat-omap/include/plat/usb.h      |    2 +-
 14 files changed, 16 insertions(+), 16 deletions(-)

diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index a101029..5822bcf 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -648,7 +648,7 @@ static void enable_board_wakeup_source(void)
 		OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
 }
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c
index 4386d2b..a0a2a11 100755
--- a/arch/arm/mach-omap2/board-3630sdp.c
+++ b/arch/arm/mach-omap2/board-3630sdp.c
@@ -54,7 +54,7 @@ static void enable_board_wakeup_source(void)
 		OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
 }
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index 70c1861..6ae8805 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -273,7 +273,7 @@ static void __init am3517_evm_init_irq(void)
 	omap_gpio_init();
 }
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index afa77ca..2de4f79 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -612,7 +612,7 @@ static struct omap2_hsmmc_info mmc[] = {
 	{}	/* Terminator */
 };
 
-static struct ehci_hcd_omap_platform_data ehci_pdata = {
+static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 3710190..5bfc13b 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -636,7 +636,7 @@ static struct omap_musb_board_data musb_board_data = {
 	.power			= 100,
 };
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 9958987..4f1accf 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -442,7 +442,7 @@ static struct omap_musb_board_data musb_board_data = {
 	.power			= 100,
 };
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 6eb77e1..962d377 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -410,7 +410,7 @@ static void __init omap3beagle_flash_init(void)
 	}
 }
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index d6bc88c..017bb2f 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -635,7 +635,7 @@ static struct platform_device *omap3_evm_devices[] __initdata = {
 	&omap3_evm_dss_device,
 };
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
 
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 4827f46..51a5315 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -537,7 +537,7 @@ static struct platform_device *omap3pandora_devices[] __initdata = {
 	&pandora_dss_device,
 };
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
index 2a5bf5c..2504d41 100644
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ b/arch/arm/mach-omap2/board-omap3touchbook.c
@@ -493,7 +493,7 @@ static void __init omap3touchbook_flash_init(void)
 	}
 }
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 50872a4..8848c7c 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -394,7 +394,7 @@ static struct platform_device *overo_devices[] __initdata = {
 	&overo_lcd_device,
 };
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 	.port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
 	.port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
diff --git a/arch/arm/mach-omap2/board-zoom3.c b/arch/arm/mach-omap2/board-zoom3.c
index d3e3cd5..cd3e40c 100644
--- a/arch/arm/mach-omap2/board-zoom3.c
+++ b/arch/arm/mach-omap2/board-zoom3.c
@@ -52,7 +52,7 @@ static struct omap_board_mux board_mux[] __initdata = {
 #define board_mux	NULL
 #endif
 
-static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
 	.port_mode[0]		= EHCI_HCD_OMAP_MODE_UNKNOWN,
 	.port_mode[1]		= EHCI_HCD_OMAP_MODE_PHY,
 	.port_mode[2]		= EHCI_HCD_OMAP_MODE_UNKNOWN,
diff --git a/arch/arm/mach-omap2/usb-ehci.c b/arch/arm/mach-omap2/usb-ehci.c
index f1df873..ee9f548 100644
--- a/arch/arm/mach-omap2/usb-ehci.c
+++ b/arch/arm/mach-omap2/usb-ehci.c
@@ -70,7 +70,7 @@ static struct platform_device ehci_device = {
 /*
  * setup_ehci_io_mux - initialize IO pad mux for USBHOST
  */
-static void setup_ehci_io_mux(enum ehci_hcd_omap_mode *port_mode)
+static void setup_ehci_io_mux(const enum ehci_hcd_omap_mode *port_mode)
 {
 	switch (port_mode[0]) {
 	case EHCI_HCD_OMAP_MODE_PHY:
@@ -213,7 +213,7 @@ static void setup_ehci_io_mux(enum ehci_hcd_omap_mode *port_mode)
 	return;
 }
 
-void __init usb_ehci_init(struct ehci_hcd_omap_platform_data *pdata)
+void __init usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata)
 {
 	platform_device_add_data(&ehci_device, pdata, sizeof(*pdata));
 
@@ -229,7 +229,7 @@ void __init usb_ehci_init(struct ehci_hcd_omap_platform_data *pdata)
 
 #else
 
-void __init usb_ehci_init(struct ehci_hcd_omap_platform_data *pdata)
+void __init usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata)
 
 {
 }
diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
index 288e29e..568578d 100644
--- a/arch/arm/plat-omap/include/plat/usb.h
+++ b/arch/arm/plat-omap/include/plat/usb.h
@@ -53,7 +53,7 @@ enum musb_interface    {MUSB_INTERFACE_ULPI, MUSB_INTERFACE_UTMI};
 
 extern void usb_musb_init(struct omap_musb_board_data *board_data);
 
-extern void usb_ehci_init(struct ehci_hcd_omap_platform_data *pdata);
+extern void usb_ehci_init(const struct ehci_hcd_omap_platform_data *pdata);
 
 #endif
 

[PATCH 03/19] omap4: Fix build break by moving omap_smc1 into a separate .S

[Tony Lindgren]

From: Santosh Shilimkar <santosh.shilimkar@ti.com>

This patch moves omap_smc1 function to a seperate omap44xx-smc.S file
and sets compile flags as -Wa,-march=armv7-a.

This fix was suggested by Tony Lindgren <tony@atomide.com>

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony at atomide.com: otherwise multi-omap build with V6 and V7 breaks]
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/Makefile        |    3 +++
 arch/arm/mach-omap2/board-4430sdp.c |   26 +-------------------------
 arch/arm/mach-omap2/omap44xx-smc.S  |   32 ++++++++++++++++++++++++++++++++
 3 files changed, 36 insertions(+), 25 deletions(-)
 create mode 100644 arch/arm/mach-omap2/omap44xx-smc.S

diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 2069fb3..4b9fc57 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -22,6 +22,9 @@ obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 # SMP support ONLY available for OMAP4
 obj-$(CONFIG_SMP)			+= omap-smp.o omap-headsmp.o
 obj-$(CONFIG_LOCAL_TIMERS)		+= timer-mpu.o
+obj-$(CONFIG_ARCH_OMAP4)		+= omap44xx-smc.o
+
+AFLAGS_omap44xx-smc.o			:=-Wa,-march=armv7-a
 
 # Functions loaded to SRAM
 obj-$(CONFIG_ARCH_OMAP2420)		+= sram242x.o
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 180ac11..b88f28c 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -50,33 +50,9 @@ static struct omap_board_config_kernel sdp4430_config[] __initdata = {
 };
 
 #ifdef CONFIG_CACHE_L2X0
-noinline void omap_smc1(u32 fn, u32 arg)
-{
-	register u32 r12 asm("r12") = fn;
-	register u32 r0 asm("r0") = arg;
-
-	/* This is common routine cache secure monitor API used to
-	 * modify the PL310 secure registers.
-	 * r0 contains the value to be modified and "r12" contains
-	 * the monitor API number. It uses few CPU registers
-	 * internally and hence they need be backed up including
-	 * link register "lr".
-	 * Explicitly save r11 and r12 the compiler generated code
-	 * won't save it.
-	 */
-	asm volatile(
-		"stmfd r13!, {r11,r12}\n"
-		"dsb\n"
-		"smc\n"
-		"ldmfd r13!, {r11,r12}\n"
-		: "+r" (r0), "+r" (r12)
-		:
-		: "r4", "r5", "r10", "lr", "cc");
-}
-EXPORT_SYMBOL(omap_smc1);
-
 static int __init omap_l2_cache_init(void)
 {
+	extern void omap_smc1(u32 fn, u32 arg);
 	void __iomem *l2cache_base;
 
 	/* To avoid code running on other OMAPs in
diff --git a/arch/arm/mach-omap2/omap44xx-smc.S b/arch/arm/mach-omap2/omap44xx-smc.S
new file mode 100644
index 0000000..89bb2b1
--- /dev/null
+++ b/arch/arm/mach-omap2/omap44xx-smc.S
@@ -0,0 +1,32 @@
+/*
+ * OMAP44xx secure APIs file.
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ * Written by Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ *
+ * This program is free software,you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/linkage.h>
+
+/*
+ * This is common routine to manage secure monitor API
+ * used to modify the PL310 secure registers.
+ * 'r0' contains the value to be modified and 'r12' contains
+ * the monitor API number. It uses few CPU registers
+ * internally and hence they need be backed up including
+ * link register "lr".
+ * Function signature : void omap_smc1(u32 fn, u32 arg)
+ */
+
+ENTRY(omap_smc1)
+	stmfd   sp!, {r2-r12, lr}
+	mov	r12, r0
+	mov 	r0, r1
+	dsb
+	smc
+	ldmfd   sp!, {r2-r12, pc}
+END(omap_smc1)

[PATCH 04/19] omap2: add USB initialization for tusb6010

[Tony Lindgren]

From: Francisco Alecrim <francisco.alecrim@openbossa.org>

Based on Kalle's and Tony's patches. Some variables re-organized
and unused code removed.

Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Francisco Alecrim <francisco.alecrim@openbossa.org>
[tony at atomide.com: this is needed to fix the related tusb6010 DMA API changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-n8x0.c     |   98 ++++++++++++++++++++++++++++++++++
 arch/arm/mach-omap2/clock2420_data.c |    1 
 2 files changed, 99 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c
index 4cab052..da9bcb8 100644
--- a/arch/arm/mach-omap2/board-n8x0.c
+++ b/arch/arm/mach-omap2/board-n8x0.c
@@ -37,6 +37,103 @@ static int slot1_cover_open;
 static int slot2_cover_open;
 static struct device *mmc_device;
 
+#define TUSB6010_ASYNC_CS	1
+#define TUSB6010_SYNC_CS	4
+#define TUSB6010_GPIO_INT	58
+#define TUSB6010_GPIO_ENABLE	0
+#define TUSB6010_DMACHAN	0x3f
+
+#if defined(CONFIG_USB_TUSB6010) || \
+	defined(CONFIG_USB_TUSB6010_MODULE)
+/*
+ * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
+ * 1.5 V voltage regulators of PM companion chip. Companion chip will then
+ * provide then PGOOD signal to TUSB6010 which will release it from reset.
+ */
+static int tusb_set_power(int state)
+{
+	int i, retval = 0;
+
+	if (state) {
+		gpio_set_value(TUSB6010_GPIO_ENABLE, 1);
+		msleep(1);
+
+		/* Wait until TUSB6010 pulls INT pin down */
+		i = 100;
+		while (i && gpio_get_value(TUSB6010_GPIO_INT)) {
+			msleep(1);
+			i--;
+		}
+
+		if (!i) {
+			printk(KERN_ERR "tusb: powerup failed\n");
+			retval = -ENODEV;
+		}
+	} else {
+		gpio_set_value(TUSB6010_GPIO_ENABLE, 0);
+		msleep(10);
+	}
+
+	return retval;
+}
+
+static struct musb_hdrc_config musb_config = {
+	.multipoint	= 1,
+	.dyn_fifo	= 1,
+	.num_eps	= 16,
+	.ram_bits	= 12,
+};
+
+static struct musb_hdrc_platform_data tusb_data = {
+#if defined(CONFIG_USB_MUSB_OTG)
+	.mode		= MUSB_OTG,
+#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
+	.mode		= MUSB_PERIPHERAL,
+#else /* defined(CONFIG_USB_MUSB_HOST) */
+	.mode		= MUSB_HOST,
+#endif
+	.set_power	= tusb_set_power,
+	.min_power	= 25,	/* x2 = 50 mA drawn from VBUS as peripheral */
+	.power		= 100,	/* Max 100 mA VBUS for host mode */
+	.config		= &musb_config,
+};
+
+static void __init n8x0_usb_init(void)
+{
+	int ret = 0;
+	static char	announce[] __initdata = KERN_INFO "TUSB 6010\n";
+
+	/* PM companion chip power control pin */
+	ret = gpio_request(TUSB6010_GPIO_ENABLE, "TUSB6010 enable");
+	if (ret != 0) {
+		printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
+		       TUSB6010_GPIO_ENABLE);
+		return;
+	}
+	gpio_direction_output(TUSB6010_GPIO_ENABLE, 0);
+
+	tusb_set_power(0);
+
+	ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
+					TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
+					TUSB6010_GPIO_INT, TUSB6010_DMACHAN);
+	if (ret != 0)
+		goto err;
+
+	printk(announce);
+
+	return;
+
+err:
+	gpio_free(TUSB6010_GPIO_ENABLE);
+}
+#else
+
+static void __init n8x0_usb_init(void) {}
+
+#endif /*CONFIG_USB_TUSB6010 */
+
+
 static struct omap2_mcspi_device_config p54spi_mcspi_config = {
 	.turbo_mode	= 0,
 	.single_channel = 1,
@@ -562,6 +659,7 @@ static void __init n8x0_init_machine(void)
 	n8x0_menelaus_init();
 	n8x0_onenand_init();
 	n8x0_mmc_init();
+	n8x0_usb_init();
 }
 
 MACHINE_START(NOKIA_N800, "Nokia N800")
diff --git a/arch/arm/mach-omap2/clock2420_data.c b/arch/arm/mach-omap2/clock2420_data.c
index f12af95..d932b14 100644
--- a/arch/arm/mach-omap2/clock2420_data.c
+++ b/arch/arm/mach-omap2/clock2420_data.c
@@ -1841,6 +1841,7 @@ static struct omap_clk omap2420_clks[] = {
 	CLK(NULL,	"aes_ick",	&aes_ick,	CK_242X),
 	CLK(NULL,	"pka_ick",	&pka_ick,	CK_242X),
 	CLK(NULL,	"usb_fck",	&usb_fck,	CK_242X),
+	CLK("musb_hdrc",	"fck",	&osc_ck,	CK_242X),
 };
 
 /*

[PATCH 05/19] omap2: Update n8x0 defconfig to test multi-omap and DMA api changes

[Tony Lindgren]

Recent DMA API changes broke compile for tusb6010. While
testing the fixes for tusb6010, I had to update the n8x0
defconfig quite a bit. Might as well merge it while at it
to make it more usable as we're using this to test the
multi-omap booting between V6 and V7 ARMs.

Also, anybody using n8x0 with a current kernel will most
likely want to mount root on the MMC instead of the onenand
to keep the Maemo install intact.

Enable I2C, REGULATOR, MMC, MFD, PM, and USB. Also change the root
to /dev/mmcblk0p2 instead of the onenand.

Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/configs/n8x0_defconfig |  160 +++++++++++++++++++++++++++++++++++----
 1 files changed, 142 insertions(+), 18 deletions(-)

diff --git a/arch/arm/configs/n8x0_defconfig b/arch/arm/configs/n8x0_defconfig
index e6f667c..216ad00 100644
--- a/arch/arm/configs/n8x0_defconfig
+++ b/arch/arm/configs/n8x0_defconfig
@@ -191,6 +191,7 @@ CONFIG_ARCH_OMAP=y
 #
 CONFIG_ARCH_OMAP_OTG=y
 # CONFIG_ARCH_OMAP1 is not set
+CONFIG_ARCH_OMAP2PLUS=y
 CONFIG_ARCH_OMAP2=y
 # CONFIG_ARCH_OMAP3 is not set
 # CONFIG_ARCH_OMAP4 is not set
@@ -198,8 +199,6 @@ CONFIG_ARCH_OMAP2=y
 #
 # OMAP Feature Selections
 #
-# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set
-# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set
 CONFIG_OMAP_RESET_CLOCKS=y
 # CONFIG_OMAP_MUX is not set
 # CONFIG_OMAP_MCBSP is not set
@@ -208,15 +207,13 @@ CONFIG_OMAP_MBOX_FWK=y
 CONFIG_OMAP_32K_TIMER=y
 CONFIG_OMAP_32K_TIMER_HZ=128
 CONFIG_OMAP_DM_TIMER=y
-# CONFIG_OMAP_LL_DEBUG_UART1 is not set
-# CONFIG_OMAP_LL_DEBUG_UART2 is not set
-CONFIG_OMAP_LL_DEBUG_UART3=y
+# CONFIG_OMAP_PM_NONE is not set
+CONFIG_OMAP_PM_NOOP=y
 # CONFIG_MACH_OMAP_GENERIC is not set
 
 #
 # OMAP Core Type
 #
-CONFIG_ARCH_OMAP24XX=y
 CONFIG_ARCH_OMAP2420=y
 # CONFIG_ARCH_OMAP2430 is not set
 
@@ -227,6 +224,9 @@ CONFIG_MACH_OMAP2_TUSB6010=y
 # CONFIG_MACH_OMAP_H4 is not set
 # CONFIG_MACH_OMAP_APOLLON is not set
 # CONFIG_MACH_OMAP_2430SDP is not set
+CONFIG_MACH_NOKIA_N800=y
+CONFIG_MACH_NOKIA_N810=y
+CONFIG_MACH_NOKIA_N810_WIMAX=y
 CONFIG_MACH_NOKIA_N8X0=y
 
 #
@@ -303,7 +303,7 @@ CONFIG_ALIGNMENT_TRAP=y
 CONFIG_ZBOOT_ROM_TEXT=0x10C08000
 CONFIG_ZBOOT_ROM_BSS=0x10200000
 # CONFIG_ZBOOT_ROM is not set
-CONFIG_CMDLINE="root=1f03 rootfstype=jffs2 console=ttyS2,115200n8"
+CONFIG_CMDLINE="root=/dev/mmcblk0p2 console=ttyS2,115200n8 debug earlyprintk rootwait"
 # CONFIG_XIP_KERNEL is not set
 # CONFIG_KEXEC is not set
 
@@ -337,7 +337,14 @@ CONFIG_HAVE_AOUT=y
 #
 # Power management options
 #
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
+CONFIG_PM_RUNTIME=y
+CONFIG_PM_OPS=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
@@ -617,7 +624,55 @@ CONFIG_UNIX98_PTYS=y
 # CONFIG_R3964 is not set
 # CONFIG_RAW_DRIVER is not set
 # CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_COMPAT is not set
+# CONFIG_I2C_CHARDEV is not set
+# CONFIG_I2C_HELPER_AUTO is not set
+# CONFIG_I2C_SMBUS is not set
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_OMAP=y
+# CONFIG_I2C_SIMTEC is not set
+# CONFIG_I2C_XILINX is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
 CONFIG_SPI=y
 # CONFIG_SPI_DEBUG is not set
 CONFIG_SPI_MASTER=y
@@ -673,15 +728,44 @@ CONFIG_SSB_POSSIBLE=y
 # Multifunction device drivers
 #
 # CONFIG_MFD_CORE is not set
+# CONFIG_MFD_88PM860X is not set
 # CONFIG_MFD_SM501 is not set
 # CONFIG_MFD_ASIC3 is not set
 # CONFIG_HTC_EGPIO is not set
 # CONFIG_HTC_PASIC3 is not set
+# CONFIG_HTC_I2CPLD is not set
+# CONFIG_TPS65010 is not set
+CONFIG_MENELAUS=y
+# CONFIG_TWL4030_CORE is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_MFD_T7L66XB is not set
 # CONFIG_MFD_TC6387XB is not set
 # CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_PMIC_ADP5520 is not set
+# CONFIG_MFD_MAX8925 is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_WM8994 is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_EZX_PCAP is not set
+# CONFIG_AB4500_CORE is not set
+CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_DUMMY is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+# CONFIG_REGULATOR_MAX8649 is not set
+# CONFIG_REGULATOR_MAX8660 is not set
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_REGULATOR_TPS65023 is not set
+# CONFIG_REGULATOR_TPS6507X is not set
 # CONFIG_MEDIA_SUPPORT is not set
 
 #
@@ -718,7 +802,10 @@ CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
 CONFIG_USB_DEVICEFS=y
 CONFIG_USB_DEVICE_CLASS=y
 # CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_OTG is not set
+CONFIG_USB_SUSPEND=y
+CONFIG_USB_OTG=y
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
 # CONFIG_USB_MON is not set
 # CONFIG_USB_WUSB is not set
 # CONFIG_USB_WUSB_CBAF is not set
@@ -737,9 +824,10 @@ CONFIG_USB_DEVICE_CLASS=y
 CONFIG_USB_MUSB_HDRC=y
 CONFIG_USB_TUSB6010=y
 # CONFIG_USB_MUSB_HOST is not set
-CONFIG_USB_MUSB_PERIPHERAL=y
-# CONFIG_USB_MUSB_OTG is not set
+# CONFIG_USB_MUSB_PERIPHERAL is not set
+CONFIG_USB_MUSB_OTG=y
 CONFIG_USB_GADGET_MUSB_HDRC=y
+CONFIG_USB_MUSB_HDRC_HCD=y
 # CONFIG_MUSB_PIO_ONLY is not set
 # CONFIG_USB_INVENTRA_DMA is not set
 # CONFIG_USB_TI_CPPI_DMA is not set
@@ -824,44 +912,77 @@ CONFIG_USB_GADGET_DUALSPEED=y
 # CONFIG_USB_ZERO is not set
 # CONFIG_USB_AUDIO is not set
 CONFIG_USB_ETH=y
-# CONFIG_USB_ETH_RNDIS is not set
+CONFIG_USB_ETH_RNDIS=y
+CONFIG_USB_ETH_EEM=y
 # CONFIG_USB_GADGETFS is not set
 # CONFIG_USB_FILE_STORAGE is not set
+# CONFIG_USB_MASS_STORAGE is not set
 # CONFIG_USB_G_SERIAL is not set
 # CONFIG_USB_MIDI_GADGET is not set
 # CONFIG_USB_G_PRINTER is not set
 # CONFIG_USB_CDC_COMPOSITE is not set
+# CONFIG_USB_G_NOKIA is not set
+# CONFIG_USB_G_MULTI is not set
 
 #
 # OTG and related infrastructure
 #
 CONFIG_USB_OTG_UTILS=y
 # CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_ISP1301_OMAP is not set
+# CONFIG_USB_ULPI is not set
 CONFIG_NOP_USB_XCEIV=y
-# CONFIG_MMC is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+CONFIG_MMC_OMAP=y
+# CONFIG_MMC_SPI is not set
 # CONFIG_MEMSTICK is not set
-# CONFIG_ACCESSIBILITY is not set
 # CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
 CONFIG_RTC_LIB=y
 # CONFIG_RTC_CLASS is not set
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
-# CONFIG_REGULATOR is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
 # File systems
 #
 # CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT3_FS_XATTR=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
 # CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
 # CONFIG_XFS_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
 CONFIG_FILE_LOCKING=y
 CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
@@ -886,8 +1007,11 @@ CONFIG_INOTIFY_USER=y
 #
 # DOS/FAT/NT Filesystems
 #
+CONFIG_FAT_FS=y
 # CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
 # CONFIG_NTFS_FS is not set
 
 #

[PATCH 06/19] omap: Enable PM_RUNTIME in defconfigs to avoid USB compile errors

[Tony Lindgren]

While waiting for the related USB patch, fix compile by enabling
it in the defconfigs. As discussed at:

http://thread.gmane.org/gmane.linux.usb.general/27432/focus=4460

Otherwise we'll get errors like:

drivers/usb/core/hcd.c:1892: error: 'pm_wq' undeclared (first use in this function)
drivers/usb/core/hcd.c:1892: error: (Each undeclared identifier is reported only once
drivers/usb/core/hcd.c:1892: error: for each function it appears in.)

Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/configs/cm_t35_defconfig          |    2 +-
 arch/arm/configs/n770_defconfig            |    1 +
 arch/arm/configs/omap3_beagle_defconfig    |    1 +
 arch/arm/configs/omap3_defconfig           |    2 +-
 arch/arm/configs/omap3_evm_defconfig       |    1 +
 arch/arm/configs/omap3_touchbook_defconfig |    2 +-
 arch/arm/configs/omap_3430sdp_defconfig    |    1 +
 arch/arm/configs/omap_3630sdp_defconfig    |    2 +-
 arch/arm/configs/omap_h2_1610_defconfig    |    1 +
 arch/arm/configs/omap_zoom2_defconfig      |    1 +
 arch/arm/configs/omap_zoom3_defconfig      |    2 +-
 arch/arm/configs/rx51_defconfig            |    1 +
 12 files changed, 12 insertions(+), 5 deletions(-)

diff --git a/arch/arm/configs/cm_t35_defconfig b/arch/arm/configs/cm_t35_defconfig
index 893cd26..032b49b 100644
--- a/arch/arm/configs/cm_t35_defconfig
+++ b/arch/arm/configs/cm_t35_defconfig
@@ -358,7 +358,7 @@ CONFIG_PM_SLEEP=y
 CONFIG_SUSPEND=y
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
-# CONFIG_PM_RUNTIME is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/n770_defconfig b/arch/arm/configs/n770_defconfig
index 75cae18..de0c28a 100644
--- a/arch/arm/configs/n770_defconfig
+++ b/arch/arm/configs/n770_defconfig
@@ -308,6 +308,7 @@ CONFIG_PM_SLEEP=y
 CONFIG_SUSPEND_UP_POSSIBLE=y
 CONFIG_SUSPEND=y
 # CONFIG_APM_EMULATION is not set
+CONFIG_PM_RUNTIME=y
 
 #
 # Networking
diff --git a/arch/arm/configs/omap3_beagle_defconfig b/arch/arm/configs/omap3_beagle_defconfig
index c7999f5..5a9e95f 100644
--- a/arch/arm/configs/omap3_beagle_defconfig
+++ b/arch/arm/configs/omap3_beagle_defconfig
@@ -324,6 +324,7 @@ CONFIG_PM_SLEEP=y
 CONFIG_SUSPEND=y
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/omap3_defconfig b/arch/arm/configs/omap3_defconfig
index 714835e..d6ad921 100644
--- a/arch/arm/configs/omap3_defconfig
+++ b/arch/arm/configs/omap3_defconfig
@@ -450,7 +450,7 @@ CONFIG_SUSPEND=y
 # CONFIG_PM_TEST_SUSPEND is not set
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
-# CONFIG_PM_RUNTIME is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig
index e2ad859..a6dd6d1 100644
--- a/arch/arm/configs/omap3_evm_defconfig
+++ b/arch/arm/configs/omap3_evm_defconfig
@@ -340,6 +340,7 @@ CONFIG_PM_SLEEP=y
 CONFIG_SUSPEND=y
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/omap3_touchbook_defconfig b/arch/arm/configs/omap3_touchbook_defconfig
index 74fe6be..968fbaa 100644
--- a/arch/arm/configs/omap3_touchbook_defconfig
+++ b/arch/arm/configs/omap3_touchbook_defconfig
@@ -368,7 +368,7 @@ CONFIG_SUSPEND=y
 # CONFIG_PM_TEST_SUSPEND is not set
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
-# CONFIG_PM_RUNTIME is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/omap_3430sdp_defconfig b/arch/arm/configs/omap_3430sdp_defconfig
index bb2917e..ddde429 100644
--- a/arch/arm/configs/omap_3430sdp_defconfig
+++ b/arch/arm/configs/omap_3430sdp_defconfig
@@ -363,6 +363,7 @@ CONFIG_PM_SLEEP=y
 CONFIG_SUSPEND=y
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/omap_3630sdp_defconfig b/arch/arm/configs/omap_3630sdp_defconfig
index d25c3d4..609f348 100644
--- a/arch/arm/configs/omap_3630sdp_defconfig
+++ b/arch/arm/configs/omap_3630sdp_defconfig
@@ -361,7 +361,7 @@ CONFIG_SUSPEND=y
 # CONFIG_PM_TEST_SUSPEND is not set
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
-# CONFIG_PM_RUNTIME is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/omap_h2_1610_defconfig b/arch/arm/configs/omap_h2_1610_defconfig
index 5231895..91ef2ed 100644
--- a/arch/arm/configs/omap_h2_1610_defconfig
+++ b/arch/arm/configs/omap_h2_1610_defconfig
@@ -331,6 +331,7 @@ CONFIG_PM_SLEEP=y
 CONFIG_SUSPEND=y
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 
 #
diff --git a/arch/arm/configs/omap_zoom2_defconfig b/arch/arm/configs/omap_zoom2_defconfig
index a82e813..f5c6e11 100644
--- a/arch/arm/configs/omap_zoom2_defconfig
+++ b/arch/arm/configs/omap_zoom2_defconfig
@@ -343,6 +343,7 @@ CONFIG_SUSPEND=y
 # CONFIG_PM_TEST_SUSPEND is not set
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/omap_zoom3_defconfig b/arch/arm/configs/omap_zoom3_defconfig
index ff8ac3d..ea9a501 100644
--- a/arch/arm/configs/omap_zoom3_defconfig
+++ b/arch/arm/configs/omap_zoom3_defconfig
@@ -361,7 +361,7 @@ CONFIG_SUSPEND=y
 # CONFIG_PM_TEST_SUSPEND is not set
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
-# CONFIG_PM_RUNTIME is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
diff --git a/arch/arm/configs/rx51_defconfig b/arch/arm/configs/rx51_defconfig
index 193bd33..45135ff 100644
--- a/arch/arm/configs/rx51_defconfig
+++ b/arch/arm/configs/rx51_defconfig
@@ -322,6 +322,7 @@ CONFIG_PM_SLEEP=y
 CONFIG_SUSPEND=y
 CONFIG_SUSPEND_FREEZER=y
 # CONFIG_APM_EMULATION is not set
+CONFIG_PM_RUNTIME=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 

[PATCH 07/19] OMAP2: serial.c: Fix number of uarts in early_init

[Tony Lindgren]

From: Thomas Weber <swirl@gmx.li>

The omap_serial_early_init prints the following errors:

Could not get uart4_ick
Could not get uart4_fck

because all the uarts available in omap_uart[] will be initialized.
Only omap4430 and omap3630 have 4 uarts at the moment.
This patch reduces the number of uarts when cpu is not omap4430 or
omap3630.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/serial.c |   15 ++++++++++-----
 1 files changed, 10 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index b79bc89..da77930 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -644,16 +644,21 @@ static void serial_out_override(struct uart_port *up, int offset, int value)
 }
 void __init omap_serial_early_init(void)
 {
-	int i;
+	int i, nr_ports;
 	char name[16];
 
+	if (!(cpu_is_omap3630() || cpu_is_omap4430()))
+		nr_ports = 3;
+	else
+		nr_ports = ARRAY_SIZE(omap_uart);
+
 	/*
 	 * Make sure the serial ports are muxed on at this point.
 	 * You have to mux them off in device drivers later on
 	 * if not needed.
 	 */
 
-	for (i = 0; i < ARRAY_SIZE(omap_uart); i++) {
+	for (i = 0; i < nr_ports; i++) {
 		struct omap_uart_state *uart = &omap_uart[i];
 		struct platform_device *pdev = &uart->pdev;
 		struct device *dev = &pdev->dev;
@@ -669,17 +674,17 @@ void __init omap_serial_early_init(void)
 			continue;
 		}
 
-		sprintf(name, "uart%d_ick", i+1);
+		sprintf(name, "uart%d_ick", i + 1);
 		uart->ick = clk_get(NULL, name);
 		if (IS_ERR(uart->ick)) {
-			printk(KERN_ERR "Could not get uart%d_ick\n", i+1);
+			printk(KERN_ERR "Could not get uart%d_ick\n", i + 1);
 			uart->ick = NULL;
 		}
 
 		sprintf(name, "uart%d_fck", i+1);
 		uart->fck = clk_get(NULL, name);
 		if (IS_ERR(uart->fck)) {
-			printk(KERN_ERR "Could not get uart%d_fck\n", i+1);
+			printk(KERN_ERR "Could not get uart%d_fck\n", i + 1);
 			uart->fck = NULL;
 		}
 

[PATCH 08/19] omap2/3/4: mailbox: remove compiler warning

[Tony Lindgren]

From: Suman Anna <s-anna@ti.com>

Remove a compiler warning in device-specific
mailbox module.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/mailbox.c |   12 ++++++------
 1 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/mailbox.c b/arch/arm/mach-omap2/mailbox.c
index 52a981c..318f363 100644
--- a/arch/arm/mach-omap2/mailbox.c
+++ b/arch/arm/mach-omap2/mailbox.c
@@ -430,19 +430,19 @@ static int __devinit omap2_mbox_probe(struct platform_device *pdev)
 		if (unlikely(!res)) {
 			dev_err(&pdev->dev, "invalid irq resource\n");
 			ret = -ENODEV;
-			goto err_iva1;
+			omap_mbox_unregister(&mbox_dsp_info);
+			goto err_dsp;
 		}
 		mbox_iva_info.irq = res->start;
 		ret = omap_mbox_register(&pdev->dev, &mbox_iva_info);
-		if (ret)
-			goto err_iva1;
+		if (ret) {
+			omap_mbox_unregister(&mbox_dsp_info);
+			goto err_dsp;
+		}
 	}
 #endif
 	return 0;
 
-err_iva1:
-	omap_mbox_unregister(&mbox_dsp_info);
-
 err_dsp:
 	iounmap(mbox_base);
 	return ret;

[PATCH 09/19] omap: pass the reboot command to the boot loader

[Tony Lindgren]

From: Aaro Koskinen <Aaro.Koskinen@nokia.com>

This patch follows the commit be093beb608edf821b45fe00a8a080fb5c6ed4af
by Russell King:

  OMAP wishes to pass state to the boot loader upon reboot in order
  to instruct it whether to wait for USB-based reflashing or not.
  There is already a facility to do this via the reboot() syscall,
  except we ignore the string passed to machine_restart().

The patch adds the missing parameter to omap1_arch_reset() and
omap_prcm_arch_reset(), and modifies the latter to pass the reboot
command parameter to the boot loader instead of reboot mode (which is
for kernel internal use only and cannot be modified by the userspace).

Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/prcm.c               |    4 ++--
 arch/arm/plat-omap/include/plat/prcm.h   |    2 +-
 arch/arm/plat-omap/include/plat/system.h |    6 +++---
 3 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index 81872aa..9537f6f 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -133,7 +133,7 @@ u32 omap_prcm_get_reset_sources(void)
 EXPORT_SYMBOL(omap_prcm_get_reset_sources);
 
 /* Resets clock rates and reboots the system. Only called from system.h */
-void omap_prcm_arch_reset(char mode)
+void omap_prcm_arch_reset(char mode, const char *cmd)
 {
 	s16 prcm_offs = 0;
 
@@ -145,7 +145,7 @@ void omap_prcm_arch_reset(char mode)
 		u32 l;
 
 		prcm_offs = OMAP3430_GR_MOD;
-		l = ('B' << 24) | ('M' << 16) | mode;
+		l = ('B' << 24) | ('M' << 16) | (cmd ? (u8)*cmd : 0);
 		/* Reserve the first word in scratchpad for communicating
 		 * with the boot ROM. A pointer to a data structure
 		 * describing the boot process can be stored there,
diff --git a/arch/arm/plat-omap/include/plat/prcm.h b/arch/arm/plat-omap/include/plat/prcm.h
index d6a0e27..9fbd914 100644
--- a/arch/arm/plat-omap/include/plat/prcm.h
+++ b/arch/arm/plat-omap/include/plat/prcm.h
@@ -24,7 +24,7 @@
 #define __ASM_ARM_ARCH_OMAP_PRCM_H
 
 u32 omap_prcm_get_reset_sources(void);
-void omap_prcm_arch_reset(char mode);
+void omap_prcm_arch_reset(char mode, const char *cmd);
 int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
 			 const char *name);
 
diff --git a/arch/arm/plat-omap/include/plat/system.h b/arch/arm/plat-omap/include/plat/system.h
index c58a4ef..d0a119f 100644
--- a/arch/arm/plat-omap/include/plat/system.h
+++ b/arch/arm/plat-omap/include/plat/system.h
@@ -22,7 +22,7 @@ static inline void arch_idle(void)
 	cpu_do_idle();
 }
 
-static inline void omap1_arch_reset(char mode)
+static inline void omap1_arch_reset(char mode, const char *cmd)
 {
 	/*
 	 * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
@@ -43,9 +43,9 @@ static inline void omap1_arch_reset(char mode)
 static inline void arch_reset(char mode, const char *cmd)
 {
 	if (!cpu_class_is_omap2())
-		omap1_arch_reset(mode);
+		omap1_arch_reset(mode, cmd);
 	else
-		omap_prcm_arch_reset(mode);
+		omap_prcm_arch_reset(mode, cmd);
 }
 
 #endif

[PATCH 10/19] omap: Checkpatch cleanup for blizzard.h

[Tony Lindgren]

From: Andrea Gelmini <andrea.gelmini@gelma.net>

arch/arm/plat-omap/include/plat/blizzard.h:9:
ERROR: spaces prohibited around that ':' (ctx:WxW)

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/plat-omap/include/plat/blizzard.h |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/arm/plat-omap/include/plat/blizzard.h b/arch/arm/plat-omap/include/plat/blizzard.h
index 8d160f1..56e7f2e 100644
--- a/arch/arm/plat-omap/include/plat/blizzard.h
+++ b/arch/arm/plat-omap/include/plat/blizzard.h
@@ -6,7 +6,7 @@ struct blizzard_platform_data {
 	void		(*power_down)(struct device *dev);
 	unsigned long	(*get_clock_rate)(struct device *dev);
 
-	unsigned	te_connected : 1;
+	unsigned	te_connected:1;
 };
 
 #endif

[PATCH 11/19] omap3: Fix support for the LEDs connected to GPIO outputs on IGEP v2board

[Tony Lindgren]

From: Enric Balletbo i Serra <eballetbo@iseebcn.com>

Select CONFIG_LEDS_GPIO to enable IGEP v2 LED support and control of supported
LEDs from userspace. Otherwise GPIO LEDs are exported as GPIO 26, 27 and 28 using
the gpiolib framework.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-igep0020.c |   54 +++++++++++++++++++++++-----------
 1 files changed, 36 insertions(+), 18 deletions(-)

diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index 4f1accf..3c7789d 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -16,7 +16,6 @@
 #include <linux/clk.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
-#include <linux/leds.h>
 #include <linux/interrupt.h>
 
 #include <linux/regulator/machine.h>
@@ -39,8 +38,8 @@
 #define IGEP2_SMSC911X_CS       5
 #define IGEP2_SMSC911X_GPIO     176
 #define IGEP2_GPIO_USBH_NRESET  24
-#define IGEP2_GPIO_LED0_RED 	26
-#define IGEP2_GPIO_LED0_GREEN 	27
+#define IGEP2_GPIO_LED0_GREEN 	26
+#define IGEP2_GPIO_LED0_RED 	27
 #define IGEP2_GPIO_LED1_RED   	28
 #define IGEP2_GPIO_DVI_PUP	170
 #define IGEP2_GPIO_WIFI_NPD 	94
@@ -355,34 +354,50 @@ static void __init igep2_display_init(void)
 	    gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1))
 		pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
 }
-#ifdef CONFIG_LEDS_TRIGGERS
-static struct gpio_led gpio_leds[] = {
+
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+#include <linux/leds.h>
+
+static struct gpio_led igep2_gpio_leds[] = {
 	{
-		.name = "GPIO_LED1_RED",
+		.name = "led0:red",
+		.gpio = IGEP2_GPIO_LED0_RED,
+	},
+	{
+		.name = "led0:green",
 		.default_trigger = "heartbeat",
+		.gpio = IGEP2_GPIO_LED0_GREEN,
+	},
+	{
+		.name = "led1:red",
 		.gpio = IGEP2_GPIO_LED1_RED,
 	},
 };
 
-static struct gpio_led_platform_data gpio_leds_info = {
-	.leds           = gpio_leds,
-	.num_leds       = ARRAY_SIZE(gpio_leds),
+static struct gpio_led_platform_data igep2_led_pdata = {
+	.leds           = igep2_gpio_leds,
+	.num_leds       = ARRAY_SIZE(igep2_gpio_leds),
 };
 
-static struct platform_device leds_gpio = {
+static struct platform_device igep2_led_device = {
 	 .name   = "leds-gpio",
 	 .id     = -1,
 	 .dev    = {
-		 .platform_data  =  &gpio_leds_info,
+		 .platform_data  =  &igep2_led_pdata,
 	},
 };
+
+static void __init igep2_init_led(void)
+{
+	platform_device_register(&igep2_led_device);
+}
+
+#else
+static inline void igep2_init_led(void) {}
 #endif
 
 static struct platform_device *igep2_devices[] __initdata = {
 	&igep2_dss_device,
-#ifdef CONFIG_LEDS_TRIGGERS
-	&leds_gpio,
-#endif
 };
 
 static void __init igep2_init_irq(void)
@@ -471,31 +486,34 @@ static void __init igep2_init(void)
 	usb_ehci_init(&ehci_pdata);
 
 	igep2_flash_init();
+	igep2_init_led();
 	igep2_display_init();
 	igep2_init_smsc911x();
 
 	/* GPIO userspace leds */
-	if ((gpio_request(IGEP2_GPIO_LED0_RED, "GPIO_LED0_RED") == 0) &&
+#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
+	if ((gpio_request(IGEP2_GPIO_LED0_RED, "led0:red") == 0) &&
 	    (gpio_direction_output(IGEP2_GPIO_LED0_RED, 1) == 0)) {
 		gpio_export(IGEP2_GPIO_LED0_RED, 0);
 		gpio_set_value(IGEP2_GPIO_LED0_RED, 0);
 	} else
 		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_RED\n");
 
-	if ((gpio_request(IGEP2_GPIO_LED0_GREEN, "GPIO_LED0_GREEN") == 0) &&
+	if ((gpio_request(IGEP2_GPIO_LED0_GREEN, "led0:green") == 0) &&
 	    (gpio_direction_output(IGEP2_GPIO_LED0_GREEN, 1) == 0)) {
 		gpio_export(IGEP2_GPIO_LED0_GREEN, 0);
 		gpio_set_value(IGEP2_GPIO_LED0_GREEN, 0);
 	} else
 		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_GREEN\n");
-#ifndef CONFIG_LEDS_TRIGGERS
-	if ((gpio_request(IGEP2_GPIO_LED1_RED, "GPIO_LED1_RED") == 0) &&
+
+	if ((gpio_request(IGEP2_GPIO_LED1_RED, "led1:red") == 0) &&
 	    (gpio_direction_output(IGEP2_GPIO_LED1_RED, 1) == 0)) {
 		gpio_export(IGEP2_GPIO_LED1_RED, 0);
 		gpio_set_value(IGEP2_GPIO_LED1_RED, 0);
 	} else
 		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
 #endif
+
 	/* GPIO W-LAN + Bluetooth combo module */
 	if ((gpio_request(IGEP2_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
 	    (gpio_direction_output(IGEP2_GPIO_WIFI_NPD, 1) == 0)) {

[PATCH 12/19] omap: Fix gpio_resume_after_retention

[Tony Lindgren]

From: Tony Lindgren <Aguirre>

For omap4 case, this was wrongly writing GPIO_LEVELDETECTx
registers with OMAP24XX_ offset and OMAP4_ offset.

Bug introduced in commit:

  commit 3f1686a9bfe74979c6ad538c78039730f665f77e
  Author: Tony Lindgren <tony@atomide.com>
  Date:   Mon Feb 15 09:27:25 2010 -0800

      omap: Fix gpio.c for multi-omap for omap4

Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/plat-omap/gpio.c |   10 +++++-----
 1 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c
index 337199e..76a347b 100644
--- a/arch/arm/plat-omap/gpio.c
+++ b/arch/arm/plat-omap/gpio.c
@@ -2140,18 +2140,18 @@ void omap2_gpio_resume_after_retention(void)
 		if (gen) {
 			u32 old0, old1;
 
-			if (cpu_is_omap24xx() || cpu_is_omap44xx()) {
+			if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
 				old0 = __raw_readl(bank->base +
 					OMAP24XX_GPIO_LEVELDETECT0);
 				old1 = __raw_readl(bank->base +
 					OMAP24XX_GPIO_LEVELDETECT1);
-			__raw_writel(old0 | gen, bank->base +
+				__raw_writel(old0 | gen, bank->base +
 					OMAP24XX_GPIO_LEVELDETECT0);
-			__raw_writel(old1 | gen, bank->base +
+				__raw_writel(old1 | gen, bank->base +
 					OMAP24XX_GPIO_LEVELDETECT1);
-			__raw_writel(old0, bank->base +
+				__raw_writel(old0, bank->base +
 					OMAP24XX_GPIO_LEVELDETECT0);
-			__raw_writel(old1, bank->base +
+				__raw_writel(old1, bank->base +
 					OMAP24XX_GPIO_LEVELDETECT1);
 			}
 

[PATCH 13/19] omap: mach-omap2/io.c: fix function declarations

[Tony Lindgren]

From: Aaro Koskinen <Aaro.Koskinen@nokia.com>

Get rid of the following warnings:

	warning: non-ANSI function declaration of function [...]

Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/io.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 402e8f0..ae89d55 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -237,7 +237,7 @@ static void __init _omap2_map_common_io(void)
 }
 
 #ifdef CONFIG_ARCH_OMAP2420
-void __init omap242x_map_common_io()
+void __init omap242x_map_common_io(void)
 {
 	iotable_init(omap24xx_io_desc, ARRAY_SIZE(omap24xx_io_desc));
 	iotable_init(omap242x_io_desc, ARRAY_SIZE(omap242x_io_desc));
@@ -246,7 +246,7 @@ void __init omap242x_map_common_io()
 #endif
 
 #ifdef CONFIG_ARCH_OMAP2430
-void __init omap243x_map_common_io()
+void __init omap243x_map_common_io(void)
 {
 	iotable_init(omap24xx_io_desc, ARRAY_SIZE(omap24xx_io_desc));
 	iotable_init(omap243x_io_desc, ARRAY_SIZE(omap243x_io_desc));
@@ -255,7 +255,7 @@ void __init omap243x_map_common_io()
 #endif
 
 #ifdef CONFIG_ARCH_OMAP3
-void __init omap34xx_map_common_io()
+void __init omap34xx_map_common_io(void)
 {
 	iotable_init(omap34xx_io_desc, ARRAY_SIZE(omap34xx_io_desc));
 	_omap2_map_common_io();
@@ -263,7 +263,7 @@ void __init omap34xx_map_common_io()
 #endif
 
 #ifdef CONFIG_ARCH_OMAP4
-void __init omap44xx_map_common_io()
+void __init omap44xx_map_common_io(void)
 {
 	iotable_init(omap44xx_io_desc, ARRAY_SIZE(omap44xx_io_desc));
 	_omap2_map_common_io();

[PATCH 14/19] omap3: pandora: add missing i2c3 board_info

[Tony Lindgren]

From: Grazvydas Ignotas <notasas@gmail.com>

This will allow BQ27500 fuel gauge to function.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-omap3pandora.c |   10 +++++++++-
 1 files changed, 9 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 51a5315..395d049 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -459,12 +459,20 @@ static struct i2c_board_info __initdata omap3pandora_i2c_boardinfo[] = {
 	},
 };
 
+static struct i2c_board_info __initdata omap3pandora_i2c3_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("bq27500", 0x55),
+		.flags = I2C_CLIENT_WAKE,
+	},
+};
+
 static int __init omap3pandora_i2c_init(void)
 {
 	omap_register_i2c_bus(1, 2600, omap3pandora_i2c_boardinfo,
 			ARRAY_SIZE(omap3pandora_i2c_boardinfo));
 	/* i2c2 pins are not connected */
-	omap_register_i2c_bus(3, 100, NULL, 0);
+	omap_register_i2c_bus(3, 100, omap3pandora_i2c3_boardinfo,
+			ARRAY_SIZE(omap3pandora_i2c3_boardinfo));
 	return 0;
 }
 

[PATCH 15/19] OMAP2: cpu_is_omap2*: fix compile-time removal of unused code

[Tony Lindgren]

From: Kevin Hilman <khilman@deeprootsystems.com>

Currently if omap2420 is defined but not omap2430, cpu_is_omap2430()
is still defined as a macro, instead of #define'd to zero.  This
results in conditional cpu_is_omap2430() code still being compiled,
and leads to possible compile/link errors.  In particular for hwmod
init.

To fix, add extra #ifdefs to CPU check macros to ensure that the
is_omap* macros are zero for each OMAP2 if they are not configured
into the kernel.

Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/plat-omap/include/plat/cpu.h |    8 ++++++--
 1 files changed, 6 insertions(+), 2 deletions(-)

diff --git a/arch/arm/plat-omap/include/plat/cpu.h b/arch/arm/plat-omap/include/plat/cpu.h
index ed8786c..7514174 100644
--- a/arch/arm/plat-omap/include/plat/cpu.h
+++ b/arch/arm/plat-omap/include/plat/cpu.h
@@ -167,10 +167,14 @@ IS_OMAP_SUBCLASS(443x, 0x443)
 #if defined(MULTI_OMAP2)
 # if defined(CONFIG_ARCH_OMAP2)
 #  undef  cpu_is_omap24xx
-#  undef  cpu_is_omap242x
-#  undef  cpu_is_omap243x
 #  define cpu_is_omap24xx()		is_omap24xx()
+# endif
+# if defined (CONFIG_ARCH_OMAP2420)
+#  undef  cpu_is_omap242x
 #  define cpu_is_omap242x()		is_omap242x()
+# endif
+# if defined (CONFIG_ARCH_OMAP2430)
+#  undef  cpu_is_omap243x
 #  define cpu_is_omap243x()		is_omap243x()
 # endif
 # if defined(CONFIG_ARCH_OMAP3)

[PATCH 16/19] OMAP4: fix temporary hacks that break multi-omap PM

[Tony Lindgren]

From: Kevin Hilman <khilman@deeprootsystems.com>

When building for multi-omap, and OMAP4 is enabled, CONFIG_ARCH_OMAP4
will be true and prevent included code from building/running for
OMAP2/3 as well.

This problem exists in io.c where some hwmod/PM/SDRC init code is
prevented from running even on OMAP2/3 when OMAP4 is included in a
multi-OMAP build.

A quick glance suggests that this #ifndef is no longer needed in most
of the cases.  In the remaining cases, the function is wrapped with
"if (cpu_is_omap24xx() || cpu_is_omap34xx())" which will be optimized
out for OMAP4-only builds.

Note that this is only a short-term fix.  Longer-term, OMAP4
needs to create init functions for SDRC and hwmod late-init.

Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/io.c |   13 ++++++-------
 1 files changed, 6 insertions(+), 7 deletions(-)

diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index ae89d55..87f676a 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -309,7 +309,6 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 {
 	pwrdm_init(powerdomains_omap);
 	clkdm_init(clockdomains_omap, clkdm_autodeps);
-#ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */
 	if (cpu_is_omap242x())
 		omap2420_hwmod_init();
 	else if (cpu_is_omap243x())
@@ -319,7 +318,6 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 	omap2_mux_init();
 	/* The OPP tables have to be registered before a clk init */
 	omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps);
-#endif
 
 	if (cpu_is_omap2420())
 		omap2420_clk_init();
@@ -333,11 +331,12 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 		pr_err("Could not init clock framework - unknown CPU\n");
 
 	omap_serial_early_init();
-#ifndef CONFIG_ARCH_OMAP4
-	omap_hwmod_late_init();
+	if (cpu_is_omap24xx() || cpu_is_omap34xx())   /* FIXME: OMAP4 */
+		omap_hwmod_late_init();
 	omap_pm_if_init();
-	omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
-	_omap2_init_reprogram_sdrc();
-#endif
+	if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
+		omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
+		_omap2_init_reprogram_sdrc();
+	}
 	gpmc_init();
 }

[PATCH 17/19] omap: Add DSI regulator supply to OMAP3EVM board file

[Tony Lindgren]

From: Vaibhav Hiremath <hvaibhav@ti.com>

With recent changes happened in OMAP2/3 DSS library for regulator interface, it
is required to define DSI regulator supply, without this DSS (in turn Fbdev)
fails to get regulator.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-omap3evm.c |   16 +++++++++++-----
 1 files changed, 11 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 017bb2f..a05de10 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -514,9 +514,15 @@ static struct regulator_init_data omap3_evm_vdac = {
 };
 
 /* VPLL2 for digital video outputs */
-static struct regulator_consumer_supply omap3_evm_vpll2_supply = {
-	.supply		= "vdvi",
-	.dev		= &omap3_evm_lcd_device.dev,
+static struct regulator_consumer_supply omap3_evm_vpll2_supplies[] = {
+	{
+		.supply		= "vdvi",
+		.dev		= &omap3_evm_lcd_device.dev,
+	},
+	{
+		.supply		= "vdds_dsi",
+		.dev		= &omap3_evm_dss_device.dev,
+	},
 };
 
 static struct regulator_init_data omap3_evm_vpll2 = {
@@ -530,8 +536,8 @@ static struct regulator_init_data omap3_evm_vpll2 = {
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= 1,
-	.consumer_supplies	= &omap3_evm_vpll2_supply,
+	.num_consumer_supplies	= ARRAY_SIZE(omap3_evm_vpll2_supplies),
+	.consumer_supplies	= omap3_evm_vpll2_supplies,
 };
 
 static struct twl4030_platform_data omap3evm_twldata = {

[PATCH 12/19] omap: Fix gpio_resume_after_retention

[Aguirre, Sergio]

Hi Tony,

> -----Original Message-----
> From: Tony Lindgren [mailto:tony at atomide.com]
> Sent: Thursday, March 11, 2010 5:49 PM
> To: linux-arm-kernel at lists.infradead.org
> Cc: Aguirre, Sergio; linux-omap at vger.kernel.org
> Subject: [PATCH 12/19] omap: Fix gpio_resume_after_retention
> 
> From: Tony Lindgren <Aguirre>

Something funky mix happened with the authorship here :)

Should be:

From: Sergio Aguirre <saaguirre@ti.com>

Regards,
Sergio

[PATCH 12/19] omap: Fix gpio_resume_after_retention

[Tony Lindgren]

* Aguirre, Sergio <saaguirre@ti.com> [100311 15:47]:
> Hi Tony,
> 
> > -----Original Message-----
> > From: Tony Lindgren [mailto:tony at atomide.com]
> > Sent: Thursday, March 11, 2010 5:49 PM
> > To: linux-arm-kernel at lists.infradead.org
> > Cc: Aguirre, Sergio; linux-omap at vger.kernel.org
> > Subject: [PATCH 12/19] omap: Fix gpio_resume_after_retention
> > 
> > From: Tony Lindgren <Aguirre>
> 
> Something funky mix happened with the authorship here :)
> 
> Should be:
> 
> From: Sergio Aguirre <saaguirre@ti.com>

Thanks, updated patch below.

I think this issue is related to applying patches from
patchwork.kernel.org with email addresses in Lastname, Firstname
format..

Tony

[PATCH 18/19] omap: Add DSI regulator supply to OMAP3EVM board file

[Tony Lindgren]

[PATCH 19/19] omap: McBSP: Drop unnecessary status/error bit clearing on reg_cacheretrieved register values

[Tony Lindgren]

[PATCH 12/19] omap: Fix gpio_resume_after_retention

[Aguirre, Sergio]

> -----Original Message-----
> From: Tony Lindgren [mailto:tony at atomide.com]
> Sent: Thursday, March 11, 2010 5:57 PM
> To: Aguirre, Sergio
> Cc: linux-arm-kernel at lists.infradead.org; linux-omap at vger.kernel.org
> Subject: Re: [PATCH 12/19] omap: Fix gpio_resume_after_retention
> 
> * Aguirre, Sergio <saaguirre@ti.com> [100311 15:47]:
> > Hi Tony,
> >
> > > -----Original Message-----
> > > From: Tony Lindgren [mailto:tony at atomide.com]
> > > Sent: Thursday, March 11, 2010 5:49 PM
> > > To: linux-arm-kernel at lists.infradead.org
> > > Cc: Aguirre, Sergio; linux-omap at vger.kernel.org
> > > Subject: [PATCH 12/19] omap: Fix gpio_resume_after_retention
> > >
> > > From: Tony Lindgren <Aguirre>
> >
> > Something funky mix happened with the authorship here :)
> >
> > Should be:
> >
> > From: Sergio Aguirre <saaguirre@ti.com>
> 
> Thanks, updated patch below.
> 
> I think this issue is related to applying patches from
> patchwork.kernel.org with email addresses in Lastname, Firstname
> format..

Hmm... I see.

I normally send my patches with this alias:

alias gsend='git send-email --smtp-server /usr/bin/msmtp --from "Sergio Aguirre <saaguirre@ti.com>" --envelope-sender="Sergio Aguirre <saaguirre@ti.com>"'

and then just do:

gsend --to='linux-omap at vger.kernel.org' patches/forLO_20100311/0001-mypatch.patch

But somehow the patch ends up (I'm guessing through TI LDAP server) changing that to "Aguirre, Sergio"...

and also Patchworks seems to continue display my old fullname: "Aguirre Rodriguez, Sergio Alberto"... I guess it's in a static data cache somewhere, maybe?

Does anyone know how to overcome this kind of scenario, and force what --from param says?

Regards,
Sergio

> 
> Tony

[PATCH 18/19] omap: Add DSI regulator supply to OMAP3EVM board file

[Tony Lindgren]

* Tony Lindgren <tony@atomide.com> [100311 15:55]:
> From 9c7ceeb2621349f180be4779d954352bcc8df9cd Mon Sep 17 00:00:00 2001
> From: Vaibhav Hiremath <hvaibhav@ti.com>
> Date: Thu, 11 Mar 2010 08:55:17 +0000
> Subject: [PATCH] omap: Add DSI regulator supply to OMAP3EVM board file
> 
> With recent changes happened in OMAP2/3 DSS library for regulator interface, it
> is required to define DSI regulator supply, without this DSS (in turn Fbdev)
> fails to get regulator.

Oops, had to manually send the last two messages.. This is already
at 17/18, so please ignore.

Regards,

Tony

[PATCH 19/19] omap: McBSP: Drop unnecessary status/error bit clearing on reg_cacheretrieved register values

[Tony Lindgren]

* Tony Lindgren <tony@atomide.com> [100311 16:04]:
> From eee91441bf26c6ea88656eb9866e706b1e07d30b Mon Sep 17 00:00:00 2001
> From: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
> Date: Tue, 23 Feb 2010 15:50:38 +0000
> Subject: [PATCH] omap: McBSP: Drop unnecessary status/error bit clearing on reg_cacheretrieved register values
> 
> The MsBSP register cache will never have any error/status flags set, since
> these flags are never written to the reg_cache. So it is kind of not
> necessary to clear these flags, which are actually always 0.
> 
> In other words, clearing the status/error flags are not necessary, since the
> reg_cache will never got these bits set. We can just write back the
> register content from the cache as it is when clearing an error condition.
> 
> Tested on Amstrad Delta.

And this one is really patch 18/19. Sorry again.

Tony

[PATCH 19b/19] ARM/OMAP: Remove the +x bit from a couple of source files

[Tony Lindgren]

[PATCH 17/19] omap: Add DSI regulator supply to OMAP3EVM board file

[Hiremath, Vaibhav]

> -----Original Message-----
> From: Tony Lindgren [mailto:tony at atomide.com]
> Sent: Friday, March 12, 2010 5:19 AM
> To: linux-arm-kernel at lists.infradead.org
> Cc: Tomi Valkeinen; linux-omap at vger.kernel.org; Hiremath, Vaibhav
> Subject: [PATCH 17/19] omap: Add DSI regulator supply to OMAP3EVM board file
> 
> From: Vaibhav Hiremath <hvaibhav@ti.com>
> 
> With recent changes happened in OMAP2/3 DSS library for regulator interface,
> it
> is required to define DSI regulator supply, without this DSS (in turn Fbdev)
> fails to get regulator.
> 
> Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
> Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
>  arch/arm/mach-omap2/board-omap3evm.c |   16 +++++++++++-----
>  1 files changed, 11 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-
> omap2/board-omap3evm.c
> index 017bb2f..a05de10 100644
> --- a/arch/arm/mach-omap2/board-omap3evm.c
> +++ b/arch/arm/mach-omap2/board-omap3evm.c
> @@ -514,9 +514,15 @@ static struct regulator_init_data omap3_evm_vdac = {
>  };
> 
>  /* VPLL2 for digital video outputs */
> -static struct regulator_consumer_supply omap3_evm_vpll2_supply = {
> -	.supply		= "vdvi",
> -	.dev		= &omap3_evm_lcd_device.dev,
> +static struct regulator_consumer_supply omap3_evm_vpll2_supplies[] = {
> +	{
> +		.supply		= "vdvi",
> +		.dev		= &omap3_evm_lcd_device.dev,
> +	},
> +	{
> +		.supply		= "vdds_dsi",
> +		.dev		= &omap3_evm_dss_device.dev,
> +	},
>  };
> 
>  static struct regulator_init_data omap3_evm_vpll2 = {
> @@ -530,8 +536,8 @@ static struct regulator_init_data omap3_evm_vpll2 = {
>  		.valid_ops_mask		= REGULATOR_CHANGE_MODE
>  					| REGULATOR_CHANGE_STATUS,
>  	},
> -	.num_consumer_supplies	= 1,
> -	.consumer_supplies	= &omap3_evm_vpll2_supply,
> +	.num_consumer_supplies	= ARRAY_SIZE(omap3_evm_vpll2_supplies),
> +	.consumer_supplies	= omap3_evm_vpll2_supplies,
>  };
> 
>  static struct twl4030_platform_data omap3evm_twldata = {
[Hiremath, Vaibhav] Tony,
Please use the patch below, I have fixed Mark's comments to use devname instead of dev.

diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index ea1014b..f5c815a 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -514,10 +514,8 @@ static struct regulator_init_data omap3_evm_vdac = {
 };

 /* VPLL2 for digital video outputs */
-static struct regulator_consumer_supply omap3_evm_vpll2_supply = {
-       .supply         = "vdds_dsi",
-       .dev            = &omap3_evm_dss_device.dev,
-};
+static struct regulator_consumer_supply omap3_evm_vpll2_supply =
+       REGULATOR_SUPPLY("vdds_dsi", "omapdss");

 static struct regulator_init_data omap3_evm_vpll2 = {
        .constraints = {


[Hiremath, Vaibhav] Since you have already merged the patch , I have created patch on top of linux-omap/master below.



diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index a05de10..f5c815a 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -514,16 +514,8 @@ static struct regulator_init_data omap3_evm_vdac = {
 };

 /* VPLL2 for digital video outputs */
-static struct regulator_consumer_supply omap3_evm_vpll2_supplies[] = {
-       {
-               .supply         = "vdvi",
-               .dev            = &omap3_evm_lcd_device.dev,
-       },
-       {
-               .supply         = "vdds_dsi",
-               .dev            = &omap3_evm_dss_device.dev,
-       },
-};
+static struct regulator_consumer_supply omap3_evm_vpll2_supply =
+       REGULATOR_SUPPLY("vdds_dsi", "omapdss");

 static struct regulator_init_data omap3_evm_vpll2 = {
        .constraints = {
@@ -536,8 +528,8 @@ static struct regulator_init_data omap3_evm_vpll2 = {
                .valid_ops_mask         = REGULATOR_CHANGE_MODE
                                        | REGULATOR_CHANGE_STATUS,
        },
-       .num_consumer_supplies  = ARRAY_SIZE(omap3_evm_vpll2_supplies),
-       .consumer_supplies      = omap3_evm_vpll2_supplies,
+       .num_consumer_supplies  = 1,
+       .consumer_supplies      = &omap3_evm_vpll2_supply,
 };

 static struct twl4030_platform_data omap3evm_twldata = {
diff --git a/drivers/mtd/maps/omap_nor.c b/drivers/mtd/maps/omap_nor.c
deleted file mode 100644
index e69de29..0000000

Thanks,
Vaibhav

[PATCH 12/19] omap: Fix gpio_resume_after_retention

[Gadiyar, Anand]

> I normally send my patches with this alias:
> 
> alias gsend='git send-email --smtp-server /usr/bin/msmtp 
> --from "Sergio Aguirre <saaguirre@ti.com>" 
> --envelope-sender="Sergio Aguirre <saaguirre@ti.com>"'
> 
> and then just do:
> 
> gsend --to='linux-omap at vger.kernel.org' 
> patches/forLO_20100311/0001-mypatch.patch
> 
> But somehow the patch ends up (I'm guessing through TI LDAP 
> server) changing that to "Aguirre, Sergio"...
> 
> and also Patchworks seems to continue display my old 
> fullname: "Aguirre Rodriguez, Sergio Alberto"... I guess it's 
> in a static data cache somewhere, maybe?
> 
> Does anyone know how to overcome this kind of scenario, and 
> force what --from param says?

I send patches with an explicit "From: Anand Gadiyar <gadiyar@ti.com>"
line in the content. This seems to work okay.

Can you check if this works for you?

- Anand

[PATCH 12/19] omap: Fix gpio_resume_after_retention

[Felipe Balbi]

On Fri, Mar 12, 2010 at 11:37:50AM +0100, ext Gadiyar, Anand wrote:
>I send patches with an explicit "From: Anand Gadiyar <gadiyar@ti.com>"
>line in the content. This seems to work okay.
>
>Can you check if this works for you?

$ git config --global sendemail.from "Sergio Aguirre <saaguirre@ti.com>"
$ git send-email --to linux-omap at vger.kernel.org --from saaguirre at ti.com 0001-mypatch.patch

This will forge git to add the From: Sergio Aguirre <saaguirre@ti.com> 
when sending the patches

-- 
balbi

[PATCH 12/19] omap: Fix gpio_resume_after_retention

[Aguirre, Sergio]

From: Felipe Balbi [mailto:felipe.balbi at nokia.com]
Sent: Friday, March 12, 2010 7:19 AM
> On Fri, Mar 12, 2010 at 11:37:50AM +0100, ext Gadiyar, Anand wrote:
> >I send patches with an explicit "From: Anand Gadiyar <gadiyar@ti.com>"
> >line in the content. This seems to work okay.
> >
> >Can you check if this works for you?
> 
> $ git config --global sendemail.from "Sergio Aguirre <saaguirre@ti.com>"
> $ git send-email --to linux-omap at vger.kernel.org --from saaguirre at ti.com
> 0001-mypatch.patch
> 
> This will forge git to add the From: Sergio Aguirre <saaguirre@ti.com>
> when sending the patches

Great!

Thanks, Anand and Felipe. I'll definitely experiment with those 2.

Regards,
Sergio

> 
> --
> balbi

[PATCH 17/19] omap: Add DSI regulator supply to OMAP3EVM board file

[Tony Lindgren]

* Hiremath, Vaibhav <hvaibhav@ti.com> [100311 20:45]:
> [Hiremath, Vaibhav] Tony,
> Please use the patch below, I have fixed Mark's comments to use devname instead of dev.

Sorry, looks like I missed Mark's comments while reading the
thread at:

http://patchwork.kernel.org/patch/84823/

I can't get either of your patches to apply. Please just repost your
whole patch against the 2.6.34-rc1 with the Acked-by from Tomi.

Also, please read the mailing list instructions we have at:

http://www.elinux.org/Netiquette

Basically one patch per mail. In format that can be applied as it is.
Patches inlined, not quoted-printable. I don't want to manually re-edit
the patches, it's a complete waste of time.
 
> diff --git a/drivers/mtd/maps/omap_nor.c b/drivers/mtd/maps/omap_nor.c
> deleted file mode 100644
> index e69de29..0000000

And this part we don't want to apply, it's not related to this patch.

Regards,

Tony

[PATCH 17/19] omap: Add DSI regulator supply to OMAP3EVM board file

[Tony Lindgren]

* Tony Lindgren <tony@atomide.com> [100312 09:08]:
> * Hiremath, Vaibhav <hvaibhav@ti.com> [100311 20:45]:
> > [Hiremath, Vaibhav] Tony,
> > Please use the patch below, I have fixed Mark's comments to use devname instead of dev.
> 
> Sorry, looks like I missed Mark's comments while reading the
> thread at:
> 
> http://patchwork.kernel.org/patch/84823/
> 
> I can't get either of your patches to apply. Please just repost your
> whole patch against the 2.6.34-rc1 with the Acked-by from Tomi.
> 
> Also, please read the mailing list instructions we have at:
> 
> http://www.elinux.org/Netiquette
> 
> Basically one patch per mail. In format that can be applied as it is.
> Patches inlined, not quoted-printable. I don't want to manually re-edit
> the patches, it's a complete waste of time.
>  
> > diff --git a/drivers/mtd/maps/omap_nor.c b/drivers/mtd/maps/omap_nor.c
> > deleted file mode 100644
> > index e69de29..0000000
> 
> And this part we don't want to apply, it's not related to this patch.

Also, since this is not urgent to get things compiling again, I'll
drop this for now. We can merge it with the next set of fixes.

Regards,

Tony