[PATCH] Allow the i.mx25 3DStack target to compile.

[jcd@tribudubois.net (Jean-Christophe Dubois)]

le mardi 4 mai 2010 Baruch Siach a ?crit
> Hi Jean-Christophe,
> 
> On Tue, May 04, 2010 at 09:10:48PM +0200, Jean-Christophe DUBOIS wrote:
> > This is a resend because I wrongly submited this pach to
> > linux-arm mailing list instead of linux-arm-kernel.
> > 
> > The FEC driver is not compiling for 3Dstack evaluation board
> > in the actual state. Fix it.
> 
> See http://patchwork.ozlabs.org/patch/41235/ for a better alternative. For
> some reason this patch hasn't found its way to the mainline kernel yet.
> Until it does the i.MX25 PDK platform code is broken.

OK thanks.

Strange that this platform is still broken after almost 2 kernel releases.

> 
> > Signed-off-by: Jean-Chrsitophe DUBOIS <jcd@tribudubois.net>
> > ---
> > 
> >  arch/arm/mach-mx25/mx25pdk.c |    9 ++++-----
> 
> This file has been renamed to mach-mx25pdk.c since 2.6.34-rc2, so your
> patch does not apply.

Sure, my patch was against the latest stable (aka 2.6.33.3). Sorry about that.

> 
> baruch
> 
> >  1 files changed, 4 insertions(+), 5 deletions(-)
> > 
> > diff --git a/arch/arm/mach-mx25/mx25pdk.c b/arch/arm/mach-mx25/mx25pdk.c
> > index 6f06089..cbf45c0 100644
> > --- a/arch/arm/mach-mx25/mx25pdk.c
> > +++ b/arch/arm/mach-mx25/mx25pdk.c
> > @@ -22,7 +22,6 @@
> > 
> >  #include <linux/clk.h>
> >  #include <linux/irq.h>
> >  #include <linux/gpio.h>
> > 
> > -#include <linux/fec.h>
> > 
> >  #include <linux/platform_device.h>
> >  
> >  #include <mach/hardware.h>
> > 
> > @@ -56,8 +55,9 @@ static struct pad_desc mx25pdk_pads[] = {
> > 
> >  	MX25_PAD_D12__GPIO_4_8, /* FEC_RESET_B, GPIO 104 */
> >  
> >  };
> > 
> > -static struct fec_platform_data mx25_fec_pdata = {
> > -        .phy    = PHY_INTERFACE_MODE_RMII,
> > +static struct platform_device *platform_devices[] __initdata = {
> > +	&mxc_usbh2,
> > +        &mx25_fec_device,
> > 
> >  };
> >  
> >  #define FEC_ENABLE_GPIO		35
> > 
> > @@ -83,10 +83,9 @@ static void __init mx25pdk_init(void)
> > 
> >  			ARRAY_SIZE(mx25pdk_pads));
> >  	
> >  	mxc_register_device(&mxc_uart_device0, &uart_pdata);
> > 
> > -	mxc_register_device(&mxc_usbh2, NULL);
> > 
> >  	mx25pdk_fec_reset();
> > 
> > -	mxc_register_device(&mx25_fec_device, &mx25_fec_pdata);
> > +        platform_add_devices(platform_devices,
> > ARRAY_SIZE(platform_devices));
> > 
> >  }
> >  
> >  static void __init mx25pdk_timer_init(void)