From mboxrd@z Thu Jan 1 00:00:00 1970 From: s.hauer@pengutronix.de (Sascha Hauer) Date: Fri, 28 May 2010 10:02:17 +0200 Subject: [PATCH] mxc_nand: Fix OOB accesses on i.MX27 Message-ID: <20100528080217.GH23664@pengutronix.de> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Hi all, The OOB handling in the mxc_nand driver is broken for v1 type controllers (i.MX27/31) with 512 byte page size. This perhaps did not show up because ubi does not use OOB. Update the driver to always read/write a whole page even if only OOB is requested. With this patch the driver passes the mtd_oobtest on i.MX27 with 512 byte page size. Also tested with 2048 byte page size and on i.MX35 (v2 type controller) Signed-off-by: Sascha Hauer --- drivers/mtd/nand/mxc_nand.c | 31 +++++-------------------------- 1 files changed, 5 insertions(+), 26 deletions(-) diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c index 82e9438..6e8aa34 100644 --- a/drivers/mtd/nand/mxc_nand.c +++ b/drivers/mtd/nand/mxc_nand.c @@ -623,8 +623,7 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command, else host->buf_start = column + mtd->writesize; - if (mtd->writesize > 512) - command = NAND_CMD_READ0; /* only READ0 is valid */ + command = NAND_CMD_READ0; /* only READ0 is valid */ send_cmd(host, command, false); mxc_do_addr_cycle(mtd, column, page_addr); @@ -639,31 +638,11 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command, break; case NAND_CMD_SEQIN: - if (column >= mtd->writesize) { - /* - * FIXME: before send SEQIN command for write OOB, - * We must read one page out. - * For K9F1GXX has no READ1 command to set current HW - * pointer to spare area, we must write the whole page - * including OOB together. - */ - if (mtd->writesize > 512) - /* call ourself to read a page */ - mxc_nand_command(mtd, NAND_CMD_READ0, 0, - page_addr); - - host->buf_start = column; - - /* Set program pointer to spare region */ - if (mtd->writesize == 512) - send_cmd(host, NAND_CMD_READOOB, false); - } else { - host->buf_start = column; + if (column >= mtd->writesize) + /* call ourself to read a page */ + mxc_nand_command(mtd, NAND_CMD_READ0, 0, page_addr); - /* Set program pointer to page start */ - if (mtd->writesize == 512) - send_cmd(host, NAND_CMD_READ0, false); - } + host->buf_start = column; send_cmd(host, command, false); mxc_do_addr_cycle(mtd, column, page_addr); -- 1.7.1 -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |