From mboxrd@z Thu Jan 1 00:00:00 1970 From: marek.vasut@gmail.com (Marek Vasut) Date: Mon, 7 Jun 2010 08:58:36 +0200 Subject: pxa300 - DDRAM base value In-Reply-To: <1275892191.3501.17.camel@balakrishnan-desktop> References: <1275371058.7001.35.camel@balakrishnan-desktop> <201006061834.50297.marek.vasut@gmail.com> <1275892191.3501.17.camel@balakrishnan-desktop> Message-ID: <201006070858.36341.marek.vasut@gmail.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Dne Po 7. ?ervna 2010 08:29:51 balakrishnan napsal(a): > On Sun, 2010-06-06 at 18:34 +0200, Marek Vasut wrote: > > Dne Ne 6. ?ervna 2010 10:17:00 Eric Miao napsal(a): > > > On Sun, Jun 6, 2010 at 1:19 AM, Marek Vasut wrote: > > > > Dne ?t 1. ?ervna 2010 07:44:18 balakrishnan napsal(a): > > > >> I am working on pxa300 based development board and using Linux > > > >> 2.6.34. This Linux kernel already has support for following boards > > > >> 1. zylonite_pxa300 > > > >> 2. cm-x300 > > > >> 3. colibri-pxa300 > > > >> 4. littleton > > > >> > > > >> My doubt is that pxa300 based boards are using "0xa0000000" as > > > >> DDRAM base and PHYS_OFFSET is also defined in > > > >> "arch/arm/mach-pxa/include/mach/memory.h" as 0xa0000000. > > > >> But in our board DDR is mapped in 0x80000000. Does it make any > > > >> problem?. Because after mmu is turned ON, my board is hanging. > > > >> > > > >> "zreladdr-y := 0x80008000" is defined in > > > >> "arch/arm/mach-pxa/Makefile.boot" file . > > > >> my machine_desc is as follows > > > >> .phys_io = 0x40000000, > > > >> .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, > > > >> .boot_params = 0x80000100, > > > > > > > > Try editing both arch/arm/mach-pxa/Makefile.boot and > > > > arch/arm/mach/pxa/include/mach/memory.h > > > > > > > >> With Thanks > > > >> J.Balakrishnan > > > > > > > > The 0x80000000 should be aliased to 0xa0000000, but looking into the > > > > PXA docs, it is only on pxa320. Eric, any ideas on this ? > > > > > > Should be working on pxa300/310 as well. If it doesn't, check you > > > bootloader to make sure the mapping is OK, and memory doesn't exceed > > > (0xa000_0000 - 0x8000_0000). > > > > It worked last time I used the pxa310 littleton board, but I can't check > > on the pxa300 zylonite board just yet. > > > > Could you give us your bootloader details ? > > hi, > Now, I can able to boot after editing following files > arch/arm/mach-pxa/Makefile.boot and > arch/arm/mach/pxa/include/mach/memory.h (0x80000000 changed to > 0xa0000000). My doubt is It was always set to 0xa0000000, both of them. > 1.why 0x80000000 (DDR phy address) is aliased to 0xa0000000 in pxa > architecture? Because that's how the HW guys did it and because it's written in TRM (which is the holy bible(substitute any other holy object) of the CPU) ;-) > 2.In my development board two DDRAMs mapped at 0x80000000-0x88000000 and > 0xc0000000-0xc8000000, how can I inform to kernel about this different > bank and size?. Check LAKML and look for: "[PATCH] pxa/vpac270: Enable SparseMEM for 256 MB of RAM" This might give you an idea ... though it's a hack. All this goo about PHYS_OFFSET etc. will be gone in hopefully near future. Cheers! > > My Boot loader details, > ------------------------------ > =>bdi > arch_number = 0x00000B04 > env_t = 0x00000000 > boot_params = 0x80000100 > DRAM bank = 0x00000000 > -> start = 0x80000000 > -> size = 0x08000000 > DRAM bank = 0x00000001 > -> start = 0xC0000000 > -> size = 0x08000000 > ethaddr = 08:00:3e:26:0a:5b > ip_addr = 192.168.0.21 > baudrate = 115200 bps > =>ver > U-Boot 2010.03 (Jun 01 2010 - 14:27:43) > > > With Thanks > J.Balakrishnan