From mboxrd@z Thu Jan 1 00:00:00 1970 From: u.kleine-koenig@pengutronix.de (Uwe =?iso-8859-1?Q?Kleine-K=F6nig?=) Date: Wed, 30 Jun 2010 11:38:55 +0200 Subject: [PATCHv4 1/3] mx2_camera: Add soc_camera support for i.MX25/i.MX27 In-Reply-To: References: <03d6e55c39690618e92a91a580ec34549a135c79.1277096909.git.baruch@tkos.co.il> <20100630070717.GA11746@pengutronix.de> <20100630072808.GD11746@pengutronix.de> Message-ID: <20100630093855.GF11746@pengutronix.de> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Hello, On Wed, Jun 30, 2010 at 11:08:41AM +0200, Guennadi Liakhovetski wrote: > Mauro, there's a question for you below. > > On Wed, 30 Jun 2010, Uwe Kleine-K?nig wrote: > > > Hi Guennadi, > > > > On Wed, Jun 30, 2010 at 09:20:36AM +0200, Guennadi Liakhovetski wrote: > > > > > --- a/arch/arm/plat-mxc/include/mach/memory.h > > > > > +++ b/arch/arm/plat-mxc/include/mach/memory.h > > > > > @@ -44,12 +44,12 @@ > > > > > */ > > > > > #define CONSISTENT_DMA_SIZE SZ_8M > > > > > > > > > > -#elif defined(CONFIG_MX1_VIDEO) > > > > > +#elif defined(CONFIG_MX1_VIDEO) || defined(CONFIG_MX2_VIDEO) > > > > > /* > > > > > * Increase size of DMA-consistent memory region. > > > > > * This is required for i.MX camera driver to capture at least four VGA frames. > > > > > */ > > > > > #define CONSISTENT_DMA_SIZE SZ_4M > > > > > -#endif /* CONFIG_MX1_VIDEO */ > > > > > +#endif /* CONFIG_MX1_VIDEO || CONFIG_MX2_VIDEO */ > > > > Why not use CONFIG_VIDEO_MX2 here and get rid of CONFIG_MX2_VIDEO? > > > > > > Well, firstly for uniformity with MX1 and MX3, > > Using a common scheme for names on all platforms is fine, but if the > > existing names are bad better establish a nicer scheme. > > > > > secondly not to have to use > > > (CONFIG_VIDEO_MX2 || CONFIG_VIDEO_MX2_MODULE), > > ah, didn't notice that MX?_VIDEO is bool while VIDEO_MX? is tristate. > > That's fine. Still I would prefer a better naming that doesn't force > > having to look up which variable is for the driver and which is for the > > arch stuff. > > > > > also note, that > > > CONFIG_MX1_VIDEO is also used for linking of the FIQ handler for the camera. > > This is just a matter of fixing the corresponding Makefile. > > So, you call a change like > > # Support for CMOS sensor interface > -obj-$(CONFIG_MX1_VIDEO) += ksym_mx1.o mx1_camera_fiq.o > +ifneq ($(CONFIG_VIDEO_MX1),) > +obj-y += ksym_mx1.o mx1_camera_fiq.o > +endif No, I'd do something like config VIDEO_MX1_HOSTSUPPORT bool config VIDEO_MX1 tristate ... selects VIDEO_MX1_HOSTSUPPORT I'm not entirely happy with "...HOSTSUPPORT" but it's better than MX1_VIDEO. Best regards Uwe -- Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |