* [PATCHv5] mx2_camera: Add soc_camera support for i.MX25/i.MX27
@ 2010-07-01 11:03 Baruch Siach
2010-07-01 12:28 ` Uwe Kleine-König
0 siblings, 1 reply; 5+ messages in thread
From: Baruch Siach @ 2010-07-01 11:03 UTC (permalink / raw)
To: linux-arm-kernel
This is the soc_camera support developed by Sascha Hauer for the i.MX27. Alan
Carvalho de Assis modified the original driver to get it working on more recent
kernels. I modified it further to add support for i.MX25. This driver has been
tested on i.MX25 and i.MX27 based platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
---
Changes v4 -> v5
Comments from Uwe Kleine-K??nig:
Enclose mx27 DMA related stuff in #ifdefs since the dma-mx1-mx2.h is no
longer accessible to mx25 builds
s/MX2_VIDEO/VIDEO_MX2_HOSTSUPPORT/
Changes v3 -> v4
Address more comments from Guennadi Liakhovetski, including:
* Fix the double trigger handling of mx27 eMMA
* Add a FIXME comment in the code of eMMA overflow handling
Changes v2 -> v3
Address more comments from Guennadi Liakhovetski.
Applied part of Sashca's patch that I forgot in v2.
Changes v1 -> v2
Addressed the comments of Guennadi Liakhovetski except from the following:
1. The mclk_get_divisor implementation, since I don't know what this code
is good for
2. mx2_videobuf_release should not set pcdev->active on i.MX27, because
mx27_camera_frame_done needs this pointer
3. In mx27_camera_emma_buf_init I don't know the meaning of those hard
coded magic numbers
Applied i.MX27 fixes from Sascha.
arch/arm/plat-mxc/include/mach/memory.h | 4 +-
arch/arm/plat-mxc/include/mach/mx2_cam.h | 46 +
drivers/media/video/Kconfig | 13 +
drivers/media/video/Makefile | 1 +
drivers/media/video/mx2_camera.c | 1513 ++++++++++++++++++++++++++++++
5 files changed, 1575 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/plat-mxc/include/mach/mx2_cam.h
create mode 100644 drivers/media/video/mx2_camera.c
diff --git a/arch/arm/plat-mxc/include/mach/memory.h b/arch/arm/plat-mxc/include/mach/memory.h
index c4b40c3..849d891 100644
--- a/arch/arm/plat-mxc/include/mach/memory.h
+++ b/arch/arm/plat-mxc/include/mach/memory.h
@@ -44,12 +44,12 @@
*/
#define CONSISTENT_DMA_SIZE SZ_8M
-#elif defined(CONFIG_MX1_VIDEO)
+#elif defined(CONFIG_MX1_VIDEO) || defined(CONFIG_VIDEO_MX2_HOSTSUPPORT)
/*
* Increase size of DMA-consistent memory region.
* This is required for i.MX camera driver to capture at least four VGA frames.
*/
#define CONSISTENT_DMA_SIZE SZ_4M
-#endif /* CONFIG_MX1_VIDEO */
+#endif /* CONFIG_MX1_VIDEO || CONFIG_MX2_VIDEO */
#endif /* __ASM_ARCH_MXC_MEMORY_H__ */
diff --git a/arch/arm/plat-mxc/include/mach/mx2_cam.h b/arch/arm/plat-mxc/include/mach/mx2_cam.h
new file mode 100644
index 0000000..3c080a3
--- /dev/null
+++ b/arch/arm/plat-mxc/include/mach/mx2_cam.h
@@ -0,0 +1,46 @@
+/*
+ * mx2-cam.h - i.MX27/i.MX25 camera driver header file
+ *
+ * Copyright (C) 2003, Intel Corporation
+ * Copyright (C) 2008, Sascha Hauer <s.hauer@pengutronix.de>
+ * Copyright (C) 2010, Baruch Siach <baruch@tkos.co.il>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#ifndef __MACH_MX2_CAM_H_
+#define __MACH_MX2_CAM_H_
+
+#define MX2_CAMERA_SWAP16 (1 << 0)
+#define MX2_CAMERA_EXT_VSYNC (1 << 1)
+#define MX2_CAMERA_CCIR (1 << 2)
+#define MX2_CAMERA_CCIR_INTERLACE (1 << 3)
+#define MX2_CAMERA_HSYNC_HIGH (1 << 4)
+#define MX2_CAMERA_GATED_CLOCK (1 << 5)
+#define MX2_CAMERA_INV_DATA (1 << 6)
+#define MX2_CAMERA_PCLK_SAMPLE_RISING (1 << 7)
+#define MX2_CAMERA_PACK_DIR_MSB (1 << 8)
+
+/**
+ * struct mx2_camera_platform_data - optional platform data for mx2_camera
+ * @flags: any combination of MX2_CAMERA_*
+ * @clk: clock rate of the csi block / 2
+ */
+struct mx2_camera_platform_data {
+ unsigned long flags;
+ unsigned long clk;
+};
+
+#endif /* __MACH_MX2_CAM_H_ */
diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
index bdbc9d3..27e2acc 100644
--- a/drivers/media/video/Kconfig
+++ b/drivers/media/video/Kconfig
@@ -969,6 +969,19 @@ config VIDEO_OMAP2
---help---
This is a v4l2 driver for the TI OMAP2 camera capture interface
+config VIDEO_MX2_HOSTSUPPORT
+ bool
+
+config VIDEO_MX2
+ tristate "i.MX27/i.MX25 Camera Sensor Interface driver"
+ depends on VIDEO_DEV && SOC_CAMERA && (MACH_MX27 || ARCH_MX25)
+ select VIDEOBUF_DMA_CONTIG
+ select VIDEO_MX2_HOSTSUPPORT
+ ---help---
+ This is a v4l2 driver for the i.MX27 and the i.MX25 Camera Sensor
+ Interface
+
+
#
# USB Multimedia device configuration
#
diff --git a/drivers/media/video/Makefile b/drivers/media/video/Makefile
index cc93859..b08bd2b 100644
--- a/drivers/media/video/Makefile
+++ b/drivers/media/video/Makefile
@@ -162,6 +162,7 @@ obj-$(CONFIG_SOC_CAMERA) += soc_camera.o soc_mediabus.o
obj-$(CONFIG_SOC_CAMERA_PLATFORM) += soc_camera_platform.o
# soc-camera host drivers have to be linked after camera drivers
obj-$(CONFIG_VIDEO_MX1) += mx1_camera.o
+obj-$(CONFIG_VIDEO_MX2) += mx2_camera.o
obj-$(CONFIG_VIDEO_MX3) += mx3_camera.o
obj-$(CONFIG_VIDEO_PXA27x) += pxa_camera.o
obj-$(CONFIG_VIDEO_SH_MOBILE_CEU) += sh_mobile_ceu_camera.o
diff --git a/drivers/media/video/mx2_camera.c b/drivers/media/video/mx2_camera.c
new file mode 100644
index 0000000..98c93fa
--- /dev/null
+++ b/drivers/media/video/mx2_camera.c
@@ -0,0 +1,1513 @@
+/*
+ * V4L2 Driver for i.MX27/i.MX25 camera host
+ *
+ * Copyright (C) 2008, Sascha Hauer, Pengutronix
+ * Copyright (C) 2010, Baruch Siach, Orex Computed Radiography
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/dma-mapping.h>
+#include <linux/errno.h>
+#include <linux/fs.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/moduleparam.h>
+#include <linux/time.h>
+#include <linux/version.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/clk.h>
+
+#include <media/v4l2-common.h>
+#include <media/v4l2-dev.h>
+#include <media/videobuf-dma-contig.h>
+#include <media/soc_camera.h>
+#include <media/soc_mediabus.h>
+
+#include <linux/videodev2.h>
+
+#include <mach/mx2_cam.h>
+#ifdef CONFIG_MACH_MX27
+#include <mach/dma-mx1-mx2.h>
+#endif
+#include <mach/hardware.h>
+
+#include <asm/dma.h>
+
+#define MX2_CAM_DRV_NAME "mx2-camera"
+#define MX2_CAM_VERSION_CODE KERNEL_VERSION(0, 0, 5)
+#define MX2_CAM_DRIVER_DESCRIPTION "i.MX2x_Camera"
+
+/* reset values */
+#define CSICR1_RESET_VAL 0x40000800
+#define CSICR2_RESET_VAL 0x0
+#define CSICR3_RESET_VAL 0x0
+
+/* csi control reg 1 */
+#define CSICR1_SWAP16_EN (1 << 31)
+#define CSICR1_EXT_VSYNC (1 << 30)
+#define CSICR1_EOF_INTEN (1 << 29)
+#define CSICR1_PRP_IF_EN (1 << 28)
+#define CSICR1_CCIR_MODE (1 << 27)
+#define CSICR1_COF_INTEN (1 << 26)
+#define CSICR1_SF_OR_INTEN (1 << 25)
+#define CSICR1_RF_OR_INTEN (1 << 24)
+#define CSICR1_STATFF_LEVEL (3 << 22)
+#define CSICR1_STATFF_INTEN (1 << 21)
+#define CSICR1_RXFF_LEVEL(l) (((l) & 3) << 19) /* MX27 */
+#define CSICR1_FB2_DMA_INTEN (1 << 20) /* MX25 */
+#define CSICR1_FB1_DMA_INTEN (1 << 19) /* MX25 */
+#define CSICR1_RXFF_INTEN (1 << 18)
+#define CSICR1_SOF_POL (1 << 17)
+#define CSICR1_SOF_INTEN (1 << 16)
+#define CSICR1_MCLKDIV(d) (((d) & 0xF) << 12)
+#define CSICR1_HSYNC_POL (1 << 11)
+#define CSICR1_CCIR_EN (1 << 10)
+#define CSICR1_MCLKEN (1 << 9)
+#define CSICR1_FCC (1 << 8)
+#define CSICR1_PACK_DIR (1 << 7)
+#define CSICR1_CLR_STATFIFO (1 << 6)
+#define CSICR1_CLR_RXFIFO (1 << 5)
+#define CSICR1_GCLK_MODE (1 << 4)
+#define CSICR1_INV_DATA (1 << 3)
+#define CSICR1_INV_PCLK (1 << 2)
+#define CSICR1_REDGE (1 << 1)
+
+#define SHIFT_STATFF_LEVEL 22
+#define SHIFT_RXFF_LEVEL 19
+#define SHIFT_MCLKDIV 12
+
+/* control reg 3 */
+#define CSICR3_FRMCNT (0xFFFF << 16)
+#define CSICR3_FRMCNT_RST (1 << 15)
+#define CSICR3_DMA_REFLASH_RFF (1 << 14)
+#define CSICR3_DMA_REFLASH_SFF (1 << 13)
+#define CSICR3_DMA_REQ_EN_RFF (1 << 12)
+#define CSICR3_DMA_REQ_EN_SFF (1 << 11)
+#define CSICR3_RXFF_LEVEL(l) (((l) & 7) << 4) /* MX25 */
+#define CSICR3_CSI_SUP (1 << 3)
+#define CSICR3_ZERO_PACK_EN (1 << 2)
+#define CSICR3_ECC_INT_EN (1 << 1)
+#define CSICR3_ECC_AUTO_EN (1 << 0)
+
+#define SHIFT_FRMCNT 16
+
+/* csi status reg */
+#define CSISR_SFF_OR_INT (1 << 25)
+#define CSISR_RFF_OR_INT (1 << 24)
+#define CSISR_STATFF_INT (1 << 21)
+#define CSISR_DMA_TSF_FB2_INT (1 << 20) /* MX25 */
+#define CSISR_DMA_TSF_FB1_INT (1 << 19) /* MX25 */
+#define CSISR_RXFF_INT (1 << 18)
+#define CSISR_EOF_INT (1 << 17)
+#define CSISR_SOF_INT (1 << 16)
+#define CSISR_F2_INT (1 << 15)
+#define CSISR_F1_INT (1 << 14)
+#define CSISR_COF_INT (1 << 13)
+#define CSISR_ECC_INT (1 << 1)
+#define CSISR_DRDY (1 << 0)
+
+#define CSICR1 0x00
+#define CSICR2 0x04
+#define CSISR (cpu_is_mx27() ? 0x08 : 0x18)
+#define CSISTATFIFO 0x0c
+#define CSIRFIFO 0x10
+#define CSIRXCNT 0x14
+#define CSICR3 (cpu_is_mx27() ? 0x1C : 0x08)
+#define CSIDMASA_STATFIFO 0x20
+#define CSIDMATA_STATFIFO 0x24
+#define CSIDMASA_FB1 0x28
+#define CSIDMASA_FB2 0x2c
+#define CSIFBUF_PARA 0x30
+#define CSIIMAG_PARA 0x34
+
+/* EMMA PrP */
+#define PRP_CNTL 0x00
+#define PRP_INTR_CNTL 0x04
+#define PRP_INTRSTATUS 0x08
+#define PRP_SOURCE_Y_PTR 0x0c
+#define PRP_SOURCE_CB_PTR 0x10
+#define PRP_SOURCE_CR_PTR 0x14
+#define PRP_DEST_RGB1_PTR 0x18
+#define PRP_DEST_RGB2_PTR 0x1c
+#define PRP_DEST_Y_PTR 0x20
+#define PRP_DEST_CB_PTR 0x24
+#define PRP_DEST_CR_PTR 0x28
+#define PRP_SRC_FRAME_SIZE 0x2c
+#define PRP_DEST_CH1_LINE_STRIDE 0x30
+#define PRP_SRC_PIXEL_FORMAT_CNTL 0x34
+#define PRP_CH1_PIXEL_FORMAT_CNTL 0x38
+#define PRP_CH1_OUT_IMAGE_SIZE 0x3c
+#define PRP_CH2_OUT_IMAGE_SIZE 0x40
+#define PRP_SRC_LINE_STRIDE 0x44
+#define PRP_CSC_COEF_012 0x48
+#define PRP_CSC_COEF_345 0x4c
+#define PRP_CSC_COEF_678 0x50
+#define PRP_CH1_RZ_HORI_COEF1 0x54
+#define PRP_CH1_RZ_HORI_COEF2 0x58
+#define PRP_CH1_RZ_HORI_VALID 0x5c
+#define PRP_CH1_RZ_VERT_COEF1 0x60
+#define PRP_CH1_RZ_VERT_COEF2 0x64
+#define PRP_CH1_RZ_VERT_VALID 0x68
+#define PRP_CH2_RZ_HORI_COEF1 0x6c
+#define PRP_CH2_RZ_HORI_COEF2 0x70
+#define PRP_CH2_RZ_HORI_VALID 0x74
+#define PRP_CH2_RZ_VERT_COEF1 0x78
+#define PRP_CH2_RZ_VERT_COEF2 0x7c
+#define PRP_CH2_RZ_VERT_VALID 0x80
+
+#define PRP_CNTL_CH1EN (1 << 0)
+#define PRP_CNTL_CH2EN (1 << 1)
+#define PRP_CNTL_CSIEN (1 << 2)
+#define PRP_CNTL_DATA_IN_YUV420 (0 << 3)
+#define PRP_CNTL_DATA_IN_YUV422 (1 << 3)
+#define PRP_CNTL_DATA_IN_RGB16 (2 << 3)
+#define PRP_CNTL_DATA_IN_RGB32 (3 << 3)
+#define PRP_CNTL_CH1_OUT_RGB8 (0 << 5)
+#define PRP_CNTL_CH1_OUT_RGB16 (1 << 5)
+#define PRP_CNTL_CH1_OUT_RGB32 (2 << 5)
+#define PRP_CNTL_CH1_OUT_YUV422 (3 << 5)
+#define PRP_CNTL_CH2_OUT_YUV420 (0 << 7)
+#define PRP_CNTL_CH2_OUT_YUV422 (1 << 7)
+#define PRP_CNTL_CH2_OUT_YUV444 (2 << 7)
+#define PRP_CNTL_CH1_LEN (1 << 9)
+#define PRP_CNTL_CH2_LEN (1 << 10)
+#define PRP_CNTL_SKIP_FRAME (1 << 11)
+#define PRP_CNTL_SWRST (1 << 12)
+#define PRP_CNTL_CLKEN (1 << 13)
+#define PRP_CNTL_WEN (1 << 14)
+#define PRP_CNTL_CH1BYP (1 << 15)
+#define PRP_CNTL_IN_TSKIP(x) ((x) << 16)
+#define PRP_CNTL_CH1_TSKIP(x) ((x) << 19)
+#define PRP_CNTL_CH2_TSKIP(x) ((x) << 22)
+#define PRP_CNTL_INPUT_FIFO_LEVEL(x) ((x) << 25)
+#define PRP_CNTL_RZ_FIFO_LEVEL(x) ((x) << 27)
+#define PRP_CNTL_CH2B1EN (1 << 29)
+#define PRP_CNTL_CH2B2EN (1 << 30)
+#define PRP_CNTL_CH2FEN (1 << 31)
+
+/* IRQ Enable and status register */
+#define PRP_INTR_RDERR (1 << 0)
+#define PRP_INTR_CH1WERR (1 << 1)
+#define PRP_INTR_CH2WERR (1 << 2)
+#define PRP_INTR_CH1FC (1 << 3)
+#define PRP_INTR_CH2FC (1 << 5)
+#define PRP_INTR_LBOVF (1 << 7)
+#define PRP_INTR_CH2OVF (1 << 8)
+
+#define mx27_camera_emma(pcdev) (cpu_is_mx27() && pcdev->use_emma)
+
+#define MAX_VIDEO_MEM 16
+
+struct mx2_camera_dev {
+ struct device *dev;
+ struct soc_camera_host soc_host;
+ struct soc_camera_device *icd;
+ struct clk *clk_csi, *clk_emma;
+
+ unsigned int irq_csi, irq_emma;
+ void __iomem *base_csi, *base_emma;
+ unsigned long base_dma;
+
+ struct mx2_camera_platform_data *pdata;
+ struct resource *res_csi, *res_emma;
+ unsigned long platform_flags;
+
+ struct list_head capture;
+ struct list_head active_bufs;
+
+ spinlock_t lock;
+
+ int dma;
+ struct mx2_buffer *active;
+ struct mx2_buffer *fb1_active;
+ struct mx2_buffer *fb2_active;
+
+ int use_emma;
+
+ u32 csicr1;
+
+ void __iomem *discard_buffer;
+ dma_addr_t discard_buffer_dma;
+ size_t discard_size;
+};
+
+/* buffer for one video frame */
+struct mx2_buffer {
+ /* common v4l buffer stuff -- must be first */
+ struct videobuf_buffer vb;
+
+ enum v4l2_mbus_pixelcode code;
+
+ int bufnum;
+};
+
+static void mx2_camera_deactivate(struct mx2_camera_dev *pcdev)
+{
+ unsigned long flags;
+
+ clk_disable(pcdev->clk_csi);
+ writel(0, pcdev->base_csi + CSICR1);
+ if (mx27_camera_emma(pcdev)) {
+ writel(0, pcdev->base_emma + PRP_CNTL);
+ } else if (cpu_is_mx25()) {
+ spin_lock_irqsave(&pcdev->lock, flags);
+ pcdev->fb1_active = NULL;
+ pcdev->fb2_active = NULL;
+ writel(0, pcdev->base_csi + CSIDMASA_FB1);
+ writel(0, pcdev->base_csi + CSIDMASA_FB2);
+ spin_unlock_irqrestore(&pcdev->lock, flags);
+ }
+}
+
+/*
+ * The following two functions absolutely depend on the fact, that
+ * there can be only one camera on mx2 camera sensor interface
+ */
+static int mx2_camera_add_device(struct soc_camera_device *icd)
+{
+ struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+ int ret;
+ u32 csicr1;
+
+ if (pcdev->icd)
+ return -EBUSY;
+
+ ret = clk_enable(pcdev->clk_csi);
+ if (ret < 0)
+ return ret;
+
+ csicr1 = CSICR1_MCLKEN;
+
+ if (mx27_camera_emma(pcdev)) {
+ csicr1 |= CSICR1_PRP_IF_EN | CSICR1_FCC |
+ CSICR1_RXFF_LEVEL(0);
+ } else if (cpu_is_mx27())
+ csicr1 |= CSICR1_SOF_INTEN | CSICR1_RXFF_LEVEL(2);
+
+ pcdev->csicr1 = csicr1;
+ writel(pcdev->csicr1, pcdev->base_csi + CSICR1);
+
+ pcdev->icd = icd;
+
+ dev_info(icd->dev.parent, "Camera driver attached to camera %d\n",
+ icd->devnum);
+
+ return 0;
+}
+
+static void mx2_camera_remove_device(struct soc_camera_device *icd)
+{
+ struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+
+ BUG_ON(icd != pcdev->icd);
+
+ dev_info(icd->dev.parent, "Camera driver detached from camera %d\n",
+ icd->devnum);
+
+ mx2_camera_deactivate(pcdev);
+
+ if (pcdev->discard_buffer) {
+ dma_free_coherent(ici->v4l2_dev.dev, pcdev->discard_size,
+ pcdev->discard_buffer,
+ pcdev->discard_buffer_dma);
+ pcdev->discard_buffer = NULL;
+ }
+
+ pcdev->icd = NULL;
+}
+
+#ifdef CONFIG_MACH_MX27
+static void mx27_camera_dma_enable(struct mx2_camera_dev *pcdev)
+{
+ u32 tmp;
+
+ imx_dma_enable(pcdev->dma);
+
+ tmp = readl(pcdev->base_csi + CSICR1);
+ tmp |= CSICR1_RF_OR_INTEN;
+ writel(tmp, pcdev->base_csi + CSICR1);
+}
+
+static irqreturn_t mx27_camera_irq(int irq_csi, void *data)
+{
+ struct mx2_camera_dev *pcdev = data;
+ u32 status = readl(pcdev->base_csi + CSISR);
+
+ if (status & CSISR_SOF_INT && pcdev->active) {
+ u32 tmp;
+
+ tmp = readl(pcdev->base_csi + CSICR1);
+ writel(tmp | CSICR1_CLR_RXFIFO, pcdev->base_csi + CSICR1);
+ mx27_camera_dma_enable(pcdev);
+ }
+
+ writel(CSISR_SOF_INT | CSISR_RFF_OR_INT, pcdev->base_csi + CSISR);
+
+ return IRQ_HANDLED;
+}
+#else
+static irqreturn_t mx27_camera_irq(int irq_csi, void *data)
+{
+ return IRQ_NONE;
+}
+#endif /* CONFIG_MACH_MX27 */
+
+static void mx25_camera_frame_done(struct mx2_camera_dev *pcdev, int fb,
+ int state)
+{
+ struct videobuf_buffer *vb;
+ struct mx2_buffer *buf;
+ struct mx2_buffer **fb_active = fb == 1 ? &pcdev->fb1_active :
+ &pcdev->fb2_active;
+ u32 fb_reg = fb == 1 ? CSIDMASA_FB1 : CSIDMASA_FB2;
+ unsigned long flags;
+
+ spin_lock_irqsave(&pcdev->lock, flags);
+
+ vb = &(*fb_active)->vb;
+ dev_dbg(pcdev->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__,
+ vb, vb->baddr, vb->bsize);
+
+ vb->state = state;
+ do_gettimeofday(&vb->ts);
+ vb->field_count++;
+
+ wake_up(&vb->done);
+
+ if (list_empty(&pcdev->capture)) {
+ buf = NULL;
+ writel(0, pcdev->base_csi + fb_reg);
+ } else {
+ buf = list_entry(pcdev->capture.next, struct mx2_buffer,
+ vb.queue);
+ vb = &buf->vb;
+ list_del(&vb->queue);
+ vb->state = VIDEOBUF_ACTIVE;
+ writel(videobuf_to_dma_contig(vb), pcdev->base_csi + fb_reg);
+ }
+
+ *fb_active = buf;
+
+ spin_unlock_irqrestore(&pcdev->lock, flags);
+}
+
+static irqreturn_t mx25_camera_irq(int irq_csi, void *data)
+{
+ struct mx2_camera_dev *pcdev = data;
+ u32 status = readl(pcdev->base_csi + CSISR);
+
+ if (status & CSISR_DMA_TSF_FB1_INT)
+ mx25_camera_frame_done(pcdev, 1, VIDEOBUF_DONE);
+ else if (status & CSISR_DMA_TSF_FB2_INT)
+ mx25_camera_frame_done(pcdev, 2, VIDEOBUF_DONE);
+
+ /* FIXME: handle CSISR_RFF_OR_INT */
+
+ writel(status, pcdev->base_csi + CSISR);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * Videobuf operations
+ */
+static int mx2_videobuf_setup(struct videobuf_queue *vq, unsigned int *count,
+ unsigned int *size)
+{
+ struct soc_camera_device *icd = vq->priv_data;
+ int bytes_per_line = soc_mbus_bytes_per_line(icd->user_width,
+ icd->current_fmt->host_fmt);
+
+ dev_dbg(&icd->dev, "count=%d, size=%d\n", *count, *size);
+
+ if (bytes_per_line < 0)
+ return bytes_per_line;
+
+ *size = bytes_per_line * icd->user_height;
+
+ if (0 == *count)
+ *count = 32;
+ if (*size * *count > MAX_VIDEO_MEM * 1024 * 1024)
+ *count = (MAX_VIDEO_MEM * 1024 * 1024) / *size;
+
+ return 0;
+}
+
+static void free_buffer(struct videobuf_queue *vq, struct mx2_buffer *buf)
+{
+ struct soc_camera_device *icd = vq->priv_data;
+ struct videobuf_buffer *vb = &buf->vb;
+
+ dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__,
+ vb, vb->baddr, vb->bsize);
+
+ /*
+ * This waits until this buffer is out of danger, i.e., until it is no
+ * longer in STATE_QUEUED or STATE_ACTIVE
+ */
+ videobuf_waiton(vb, 0, 0);
+
+ videobuf_dma_contig_free(vq, vb);
+ dev_dbg(&icd->dev, "%s freed\n", __func__);
+
+ vb->state = VIDEOBUF_NEEDS_INIT;
+}
+
+static int mx2_videobuf_prepare(struct videobuf_queue *vq,
+ struct videobuf_buffer *vb, enum v4l2_field field)
+{
+ struct soc_camera_device *icd = vq->priv_data;
+ struct mx2_buffer *buf = container_of(vb, struct mx2_buffer, vb);
+ int bytes_per_line = soc_mbus_bytes_per_line(icd->user_width,
+ icd->current_fmt->host_fmt);
+ int ret = 0;
+
+ dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__,
+ vb, vb->baddr, vb->bsize);
+
+ if (bytes_per_line < 0)
+ return bytes_per_line;
+
+#ifdef DEBUG
+ /*
+ * This can be useful if you want to see if we actually fill
+ * the buffer with something
+ */
+ memset((void *)vb->baddr, 0xaa, vb->bsize);
+#endif
+
+ if (buf->code != icd->current_fmt->code ||
+ vb->width != icd->user_width ||
+ vb->height != icd->user_height ||
+ vb->field != field) {
+ buf->code = icd->current_fmt->code;
+ vb->width = icd->user_width;
+ vb->height = icd->user_height;
+ vb->field = field;
+ vb->state = VIDEOBUF_NEEDS_INIT;
+ }
+
+ vb->size = bytes_per_line * vb->height;
+ if (vb->baddr && vb->bsize < vb->size) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (vb->state == VIDEOBUF_NEEDS_INIT) {
+ ret = videobuf_iolock(vq, vb, NULL);
+ if (ret)
+ goto fail;
+
+ vb->state = VIDEOBUF_PREPARED;
+ }
+
+ return 0;
+
+fail:
+ free_buffer(vq, buf);
+out:
+ return ret;
+}
+
+static void mx2_videobuf_queue(struct videobuf_queue *vq,
+ struct videobuf_buffer *vb)
+{
+ struct soc_camera_device *icd = vq->priv_data;
+ struct soc_camera_host *ici =
+ to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+ struct mx2_buffer *buf = container_of(vb, struct mx2_buffer, vb);
+ unsigned long flags;
+
+ dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__,
+ vb, vb->baddr, vb->bsize);
+
+ spin_lock_irqsave(&pcdev->lock, flags);
+
+ vb->state = VIDEOBUF_QUEUED;
+ list_add_tail(&vb->queue, &pcdev->capture);
+
+ if (mx27_camera_emma(pcdev)) {
+ goto out;
+#ifdef CONFIG_MACH_MX27
+ } else if (cpu_is_mx27()) {
+ int ret;
+
+ if (pcdev->active == NULL) {
+ ret = imx_dma_setup_single(pcdev->dma,
+ videobuf_to_dma_contig(vb), vb->size,
+ (u32)pcdev->base_dma + 0x10,
+ DMA_MODE_READ);
+ if (ret) {
+ vb->state = VIDEOBUF_ERROR;
+ wake_up(&vb->done);
+ goto out;
+ }
+
+ vb->state = VIDEOBUF_ACTIVE;
+ pcdev->active = buf;
+ }
+#endif
+ } else { /* cpu_is_mx25() */
+ u32 csicr3, dma_inten = 0;
+
+ if (pcdev->fb1_active == NULL) {
+ writel(videobuf_to_dma_contig(vb),
+ pcdev->base_csi + CSIDMASA_FB1);
+ pcdev->fb1_active = buf;
+ dma_inten = CSICR1_FB1_DMA_INTEN;
+ } else if (pcdev->fb2_active == NULL) {
+ writel(videobuf_to_dma_contig(vb),
+ pcdev->base_csi + CSIDMASA_FB2);
+ pcdev->fb2_active = buf;
+ dma_inten = CSICR1_FB2_DMA_INTEN;
+ }
+
+ if (dma_inten) {
+ list_del(&vb->queue);
+ vb->state = VIDEOBUF_ACTIVE;
+
+ csicr3 = readl(pcdev->base_csi + CSICR3);
+
+ /* Reflash DMA */
+ writel(csicr3 | CSICR3_DMA_REFLASH_RFF,
+ pcdev->base_csi + CSICR3);
+
+ /* clear & enable interrupts */
+ writel(dma_inten, pcdev->base_csi + CSISR);
+ pcdev->csicr1 |= dma_inten;
+ writel(pcdev->csicr1, pcdev->base_csi + CSICR1);
+
+ /* enable DMA */
+ csicr3 |= CSICR3_DMA_REQ_EN_RFF | CSICR3_RXFF_LEVEL(1);
+ writel(csicr3, pcdev->base_csi + CSICR3);
+ }
+ }
+
+out:
+ spin_unlock_irqrestore(&pcdev->lock, flags);
+}
+
+static void mx2_videobuf_release(struct videobuf_queue *vq,
+ struct videobuf_buffer *vb)
+{
+ struct soc_camera_device *icd = vq->priv_data;
+ struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+ struct mx2_buffer *buf = container_of(vb, struct mx2_buffer, vb);
+ unsigned long flags;
+
+#ifdef DEBUG
+ dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__,
+ vb, vb->baddr, vb->bsize);
+
+ switch (vb->state) {
+ case VIDEOBUF_ACTIVE:
+ dev_info(&icd->dev, "%s (active)\n", __func__);
+ break;
+ case VIDEOBUF_QUEUED:
+ dev_info(&icd->dev, "%s (queued)\n", __func__);
+ break;
+ case VIDEOBUF_PREPARED:
+ dev_info(&icd->dev, "%s (prepared)\n", __func__);
+ break;
+ default:
+ dev_info(&icd->dev, "%s (unknown) %d\n", __func__,
+ vb->state);
+ break;
+ }
+#endif
+
+ /*
+ * Terminate only queued but inactive buffers. Active buffers are
+ * released when they become inactive after videobuf_waiton().
+ *
+ * FIXME: implement forced termination of active buffers, so that the
+ * user won't get stuck in an uninterruptible state. This requires a
+ * specific handling for each of the three DMA types that this driver
+ * supports.
+ */
+ spin_lock_irqsave(&pcdev->lock, flags);
+ if (vb->state == VIDEOBUF_QUEUED) {
+ list_del(&vb->queue);
+ vb->state = VIDEOBUF_ERROR;
+ }
+ spin_unlock_irqrestore(&pcdev->lock, flags);
+
+ free_buffer(vq, buf);
+}
+
+static struct videobuf_queue_ops mx2_videobuf_ops = {
+ .buf_setup = mx2_videobuf_setup,
+ .buf_prepare = mx2_videobuf_prepare,
+ .buf_queue = mx2_videobuf_queue,
+ .buf_release = mx2_videobuf_release,
+};
+
+static void mx2_camera_init_videobuf(struct videobuf_queue *q,
+ struct soc_camera_device *icd)
+{
+ struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+
+ videobuf_queue_dma_contig_init(q, &mx2_videobuf_ops, pcdev->dev,
+ &pcdev->lock, V4L2_BUF_TYPE_VIDEO_CAPTURE,
+ V4L2_FIELD_NONE, sizeof(struct mx2_buffer), icd);
+}
+
+#define MX2_BUS_FLAGS (SOCAM_DATAWIDTH_8 | \
+ SOCAM_MASTER | \
+ SOCAM_VSYNC_ACTIVE_HIGH | \
+ SOCAM_VSYNC_ACTIVE_LOW | \
+ SOCAM_HSYNC_ACTIVE_HIGH | \
+ SOCAM_HSYNC_ACTIVE_LOW | \
+ SOCAM_PCLK_SAMPLE_RISING | \
+ SOCAM_PCLK_SAMPLE_FALLING | \
+ SOCAM_DATA_ACTIVE_HIGH | \
+ SOCAM_DATA_ACTIVE_LOW)
+
+static int mx27_camera_emma_prp_reset(struct mx2_camera_dev *pcdev)
+{
+ u32 cntl;
+ int count = 0;
+
+ cntl = readl(pcdev->base_emma + PRP_CNTL);
+ writel(PRP_CNTL_SWRST, pcdev->base_emma + PRP_CNTL);
+ while (count++ < 100) {
+ if (!(readl(pcdev->base_emma + PRP_CNTL) & PRP_CNTL_SWRST))
+ return 0;
+ barrier();
+ udelay(1);
+ }
+
+ return -ETIMEDOUT;
+}
+
+static void mx27_camera_emma_buf_init(struct soc_camera_device *icd,
+ int bytesperline)
+{
+ struct soc_camera_host *ici =
+ to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+
+ writel(pcdev->discard_buffer_dma,
+ pcdev->base_emma + PRP_DEST_RGB1_PTR);
+ writel(pcdev->discard_buffer_dma,
+ pcdev->base_emma + PRP_DEST_RGB2_PTR);
+
+ /*
+ * We only use the EMMA engine to get rid of the broken
+ * DMA Engine. No color space consversion at the moment.
+ * We adjust incoming and outgoing pixelformat to rgb16
+ * and adjust the bytesperline accordingly.
+ */
+ writel(PRP_CNTL_CH1EN |
+ PRP_CNTL_CSIEN |
+ PRP_CNTL_DATA_IN_RGB16 |
+ PRP_CNTL_CH1_OUT_RGB16 |
+ PRP_CNTL_CH1_LEN |
+ PRP_CNTL_CH1BYP |
+ PRP_CNTL_CH1_TSKIP(0) |
+ PRP_CNTL_IN_TSKIP(0),
+ pcdev->base_emma + PRP_CNTL);
+
+ writel(((bytesperline >> 1) << 16) | icd->user_height,
+ pcdev->base_emma + PRP_SRC_FRAME_SIZE);
+ writel(((bytesperline >> 1) << 16) | icd->user_height,
+ pcdev->base_emma + PRP_CH1_OUT_IMAGE_SIZE);
+ writel(bytesperline,
+ pcdev->base_emma + PRP_DEST_CH1_LINE_STRIDE);
+ writel(0x2ca00565, /* RGB565 */
+ pcdev->base_emma + PRP_SRC_PIXEL_FORMAT_CNTL);
+ writel(0x2ca00565, /* RGB565 */
+ pcdev->base_emma + PRP_CH1_PIXEL_FORMAT_CNTL);
+
+ /* Enable interrupts */
+ writel(PRP_INTR_RDERR |
+ PRP_INTR_CH1WERR |
+ PRP_INTR_CH2WERR |
+ PRP_INTR_CH1FC |
+ PRP_INTR_CH2FC |
+ PRP_INTR_LBOVF |
+ PRP_INTR_CH2OVF,
+ pcdev->base_emma + PRP_INTR_CNTL);
+}
+
+static int mx2_camera_set_bus_param(struct soc_camera_device *icd,
+ __u32 pixfmt)
+{
+ struct soc_camera_host *ici =
+ to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+ unsigned long camera_flags, common_flags;
+ int ret = 0;
+ int bytesperline;
+ u32 csicr1 = pcdev->csicr1;
+
+ camera_flags = icd->ops->query_bus_param(icd);
+
+ common_flags = soc_camera_bus_param_compatible(camera_flags,
+ MX2_BUS_FLAGS);
+ if (!common_flags)
+ return -EINVAL;
+
+ if ((common_flags & SOCAM_HSYNC_ACTIVE_HIGH) &&
+ (common_flags & SOCAM_HSYNC_ACTIVE_LOW)) {
+ if (pcdev->platform_flags & MX2_CAMERA_HSYNC_HIGH)
+ common_flags &= ~SOCAM_HSYNC_ACTIVE_LOW;
+ else
+ common_flags &= ~SOCAM_HSYNC_ACTIVE_HIGH;
+ }
+
+ if ((common_flags & SOCAM_PCLK_SAMPLE_RISING) &&
+ (common_flags & SOCAM_PCLK_SAMPLE_FALLING)) {
+ if (pcdev->platform_flags & MX2_CAMERA_PCLK_SAMPLE_RISING)
+ common_flags &= ~SOCAM_PCLK_SAMPLE_FALLING;
+ else
+ common_flags &= ~SOCAM_PCLK_SAMPLE_RISING;
+ }
+
+ ret = icd->ops->set_bus_param(icd, common_flags);
+ if (ret < 0)
+ return ret;
+
+ if (common_flags & SOCAM_PCLK_SAMPLE_FALLING)
+ csicr1 |= CSICR1_INV_PCLK;
+ if (common_flags & SOCAM_VSYNC_ACTIVE_HIGH)
+ csicr1 |= CSICR1_SOF_POL;
+ if (common_flags & SOCAM_HSYNC_ACTIVE_HIGH)
+ csicr1 |= CSICR1_HSYNC_POL;
+ if (pcdev->platform_flags & MX2_CAMERA_SWAP16)
+ csicr1 |= CSICR1_SWAP16_EN;
+ if (pcdev->platform_flags & MX2_CAMERA_EXT_VSYNC)
+ csicr1 |= CSICR1_EXT_VSYNC;
+ if (pcdev->platform_flags & MX2_CAMERA_CCIR)
+ csicr1 |= CSICR1_CCIR_EN;
+ if (pcdev->platform_flags & MX2_CAMERA_CCIR_INTERLACE)
+ csicr1 |= CSICR1_CCIR_MODE;
+ if (pcdev->platform_flags & MX2_CAMERA_GATED_CLOCK)
+ csicr1 |= CSICR1_GCLK_MODE;
+ if (pcdev->platform_flags & MX2_CAMERA_INV_DATA)
+ csicr1 |= CSICR1_INV_DATA;
+ if (pcdev->platform_flags & MX2_CAMERA_PACK_DIR_MSB)
+ csicr1 |= CSICR1_PACK_DIR;
+
+ pcdev->csicr1 = csicr1;
+
+ bytesperline = soc_mbus_bytes_per_line(icd->user_width,
+ icd->current_fmt->host_fmt);
+ if (bytesperline < 0)
+ return bytesperline;
+
+ if (mx27_camera_emma(pcdev)) {
+ ret = mx27_camera_emma_prp_reset(pcdev);
+ if (ret)
+ return ret;
+
+ if (pcdev->discard_buffer)
+ dma_free_coherent(ici->v4l2_dev.dev,
+ pcdev->discard_size, pcdev->discard_buffer,
+ pcdev->discard_buffer_dma);
+
+ /*
+ * I didn't manage to properly enable/disable the prp
+ * on a per frame basis during running transfers,
+ * thus we allocate a buffer here and use it to
+ * discard frames when no buffer is available.
+ * Feel free to work on this ;)
+ */
+ pcdev->discard_size = icd->user_height * bytesperline;
+ pcdev->discard_buffer = dma_alloc_coherent(ici->v4l2_dev.dev,
+ pcdev->discard_size, &pcdev->discard_buffer_dma,
+ GFP_KERNEL);
+ if (!pcdev->discard_buffer)
+ return -ENOMEM;
+
+ mx27_camera_emma_buf_init(icd, bytesperline);
+ } else if (cpu_is_mx25()) {
+ writel((bytesperline * icd->user_height) >> 2,
+ pcdev->base_csi + CSIRXCNT);
+ writel((bytesperline << 16) | icd->user_height,
+ pcdev->base_csi + CSIIMAG_PARA);
+ }
+
+ writel(pcdev->csicr1, pcdev->base_csi + CSICR1);
+
+ return 0;
+}
+
+static int mx2_camera_set_crop(struct soc_camera_device *icd,
+ struct v4l2_crop *a)
+{
+ struct v4l2_rect *rect = &a->c;
+ struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
+ struct v4l2_mbus_framefmt mf;
+ int ret;
+
+ soc_camera_limit_side(&rect->left, &rect->width, 0, 2, 4096);
+ soc_camera_limit_side(&rect->top, &rect->height, 0, 2, 4096);
+
+ ret = v4l2_subdev_call(sd, video, s_crop, a);
+ if (ret < 0)
+ return ret;
+
+ /* The capture device might have changed its output */
+ ret = v4l2_subdev_call(sd, video, g_mbus_fmt, &mf);
+ if (ret < 0)
+ return ret;
+
+ dev_dbg(icd->dev.parent, "Sensor cropped %dx%d\n",
+ mf.width, mf.height);
+
+ icd->user_width = mf.width;
+ icd->user_height = mf.height;
+
+ return ret;
+}
+
+static int mx2_camera_set_fmt(struct soc_camera_device *icd,
+ struct v4l2_format *f)
+{
+ struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+ struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
+ const struct soc_camera_format_xlate *xlate;
+ struct v4l2_pix_format *pix = &f->fmt.pix;
+ struct v4l2_mbus_framefmt mf;
+ int ret;
+
+ xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat);
+ if (!xlate) {
+ dev_warn(icd->dev.parent, "Format %x not found\n",
+ pix->pixelformat);
+ return -EINVAL;
+ }
+
+ /* eMMA can only do RGB565 */
+ if (mx27_camera_emma(pcdev) && pix->pixelformat != V4L2_PIX_FMT_RGB565)
+ return -EINVAL;
+
+ mf.width = pix->width;
+ mf.height = pix->height;
+ mf.field = pix->field;
+ mf.colorspace = pix->colorspace;
+ mf.code = xlate->code;
+
+ ret = v4l2_subdev_call(sd, video, s_mbus_fmt, &mf);
+ if (ret < 0 && ret != -ENOIOCTLCMD)
+ return ret;
+
+ if (mf.code != xlate->code)
+ return -EINVAL;
+
+ pix->width = mf.width;
+ pix->height = mf.height;
+ pix->field = mf.field;
+ pix->colorspace = mf.colorspace;
+ icd->current_fmt = xlate;
+
+ return 0;
+}
+
+static int mx2_camera_try_fmt(struct soc_camera_device *icd,
+ struct v4l2_format *f)
+{
+ struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
+ struct mx2_camera_dev *pcdev = ici->priv;
+ struct v4l2_subdev *sd = soc_camera_to_subdev(icd);
+ const struct soc_camera_format_xlate *xlate;
+ struct v4l2_pix_format *pix = &f->fmt.pix;
+ struct v4l2_mbus_framefmt mf;
+ __u32 pixfmt = pix->pixelformat;
+ unsigned int width_limit;
+ int ret;
+
+ xlate = soc_camera_xlate_by_fourcc(icd, pixfmt);
+ if (pixfmt && !xlate) {
+ dev_warn(icd->dev.parent, "Format %x not found\n", pixfmt);
+ return -EINVAL;
+ }
+
+ /* FIXME: implement MX27 limits */
+
+ /* eMMA can only do RGB565 */
+ if (mx27_camera_emma(pcdev) && pixfmt != V4L2_PIX_FMT_RGB565)
+ return -EINVAL;
+
+ /* limit to MX25 hardware capabilities */
+ if (cpu_is_mx25()) {
+ if (xlate->host_fmt->bits_per_sample <= 8)
+ width_limit = 0xffff * 4;
+ else
+ width_limit = 0xffff * 2;
+ /* CSIIMAG_PARA limit */
+ if (pix->width > width_limit)
+ pix->width = width_limit;
+ if (pix->height > 0xffff)
+ pix->height = 0xffff;
+
+ pix->bytesperline = soc_mbus_bytes_per_line(pix->width,
+ xlate->host_fmt);
+ if (pix->bytesperline < 0)
+ return pix->bytesperline;
+ pix->sizeimage = pix->height * pix->bytesperline;
+ if (pix->sizeimage > (4 * 0x3ffff)) { /* CSIRXCNT limit */
+ dev_warn(icd->dev.parent,
+ "Image size (%u) above limit\n",
+ pix->sizeimage);
+ return -EINVAL;
+ }
+ }
+
+ /* limit to sensor capabilities */
+ mf.width = pix->width;
+ mf.height = pix->height;
+ mf.field = pix->field;
+ mf.colorspace = pix->colorspace;
+ mf.code = xlate->code;
+
+ ret = v4l2_subdev_call(sd, video, try_mbus_fmt, &mf);
+ if (ret < 0)
+ return ret;
+
+ if (mf.field == V4L2_FIELD_ANY)
+ mf.field = V4L2_FIELD_NONE;
+ if (mf.field != V4L2_FIELD_NONE) {
+ dev_err(icd->dev.parent, "Field type %d unsupported.\n",
+ mf.field);
+ return -EINVAL;
+ }
+
+ pix->width = mf.width;
+ pix->height = mf.height;
+ pix->field = mf.field;
+ pix->colorspace = mf.colorspace;
+
+ return 0;
+}
+
+static int mx2_camera_querycap(struct soc_camera_host *ici,
+ struct v4l2_capability *cap)
+{
+ /* cap->name is set by the friendly caller:-> */
+ strlcpy(cap->card, MX2_CAM_DRIVER_DESCRIPTION, sizeof(cap->card));
+ cap->version = MX2_CAM_VERSION_CODE;
+ cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING;
+
+ return 0;
+}
+
+static int mx2_camera_reqbufs(struct soc_camera_file *icf,
+ struct v4l2_requestbuffers *p)
+{
+ int i;
+
+ for (i = 0; i < p->count; i++) {
+ struct mx2_buffer *buf = container_of(icf->vb_vidq.bufs[i],
+ struct mx2_buffer, vb);
+ INIT_LIST_HEAD(&buf->vb.queue);
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_MACH_MX27
+static void mx27_camera_frame_done(struct mx2_camera_dev *pcdev, int state)
+{
+ struct videobuf_buffer *vb;
+ struct mx2_buffer *buf;
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&pcdev->lock, flags);
+
+ if (!pcdev->active) {
+ dev_err(pcdev->dev, "%s called with no active buffer!\n",
+ __func__);
+ goto out;
+ }
+
+ vb = &pcdev->active->vb;
+ buf = container_of(vb, struct mx2_buffer, vb);
+ WARN_ON(list_empty(&vb->queue));
+ dev_dbg(pcdev->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__,
+ vb, vb->baddr, vb->bsize);
+
+ /* _init is used to debug races, see comment in pxa_camera_reqbufs() */
+ list_del_init(&vb->queue);
+ vb->state = state;
+ do_gettimeofday(&vb->ts);
+ vb->field_count++;
+
+ wake_up(&vb->done);
+
+ if (list_empty(&pcdev->capture)) {
+ pcdev->active = NULL;
+ goto out;
+ }
+
+ pcdev->active = list_entry(pcdev->capture.next,
+ struct mx2_buffer, vb.queue);
+
+ vb = &pcdev->active->vb;
+ vb->state = VIDEOBUF_ACTIVE;
+
+ ret = imx_dma_setup_single(pcdev->dma, videobuf_to_dma_contig(vb),
+ vb->size, (u32)pcdev->base_dma + 0x10, DMA_MODE_READ);
+
+ if (ret) {
+ vb->state = VIDEOBUF_ERROR;
+ pcdev->active = NULL;
+ wake_up(&vb->done);
+ }
+
+out:
+ spin_unlock_irqrestore(&pcdev->lock, flags);
+}
+
+static void mx27_camera_dma_err_callback(int channel, void *data, int err)
+{
+ struct mx2_camera_dev *pcdev = data;
+
+ mx27_camera_frame_done(pcdev, VIDEOBUF_ERROR);
+}
+
+static void mx27_camera_dma_callback(int channel, void *data)
+{
+ struct mx2_camera_dev *pcdev = data;
+
+ mx27_camera_frame_done(pcdev, VIDEOBUF_DONE);
+}
+
+#define DMA_REQ_CSI_RX 31 /* FIXME: Add this to a resource */
+
+static int __devinit mx27_camera_dma_init(struct platform_device *pdev,
+ struct mx2_camera_dev *pcdev)
+{
+ int err;
+
+ pcdev->dma = imx_dma_request_by_prio("CSI RX DMA", DMA_PRIO_HIGH);
+ if (pcdev->dma < 0) {
+ dev_err(&pdev->dev, "%s failed to request DMA channel\n",
+ __func__);
+ return pcdev->dma;
+ }
+
+ err = imx_dma_setup_handlers(pcdev->dma, mx27_camera_dma_callback,
+ mx27_camera_dma_err_callback, pcdev);
+ if (err) {
+ dev_err(&pdev->dev, "%s failed to set DMA callback\n",
+ __func__);
+ goto err_out;
+ }
+
+ err = imx_dma_config_channel(pcdev->dma,
+ IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_FIFO,
+ IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_LINEAR,
+ DMA_REQ_CSI_RX, 1);
+ if (err) {
+ dev_err(&pdev->dev, "%s failed to config DMA channel\n",
+ __func__);
+ goto err_out;
+ }
+
+ imx_dma_config_burstlen(pcdev->dma, 64);
+
+ return 0;
+
+err_out:
+ imx_dma_free(pcdev->dma);
+
+ return err;
+}
+#endif /* CONFIG_MACH_MX27 */
+
+static unsigned int mx2_camera_poll(struct file *file, poll_table *pt)
+{
+ struct soc_camera_file *icf = file->private_data;
+
+ return videobuf_poll_stream(file, &icf->vb_vidq, pt);
+}
+
+static struct soc_camera_host_ops mx2_soc_camera_host_ops = {
+ .owner = THIS_MODULE,
+ .add = mx2_camera_add_device,
+ .remove = mx2_camera_remove_device,
+ .set_fmt = mx2_camera_set_fmt,
+ .set_crop = mx2_camera_set_crop,
+ .try_fmt = mx2_camera_try_fmt,
+ .init_videobuf = mx2_camera_init_videobuf,
+ .reqbufs = mx2_camera_reqbufs,
+ .poll = mx2_camera_poll,
+ .querycap = mx2_camera_querycap,
+ .set_bus_param = mx2_camera_set_bus_param,
+};
+
+static void mx27_camera_frame_done_emma(struct mx2_camera_dev *pcdev,
+ int bufnum, int state)
+{
+ struct mx2_buffer *buf;
+ struct videobuf_buffer *vb;
+ unsigned long phys;
+
+ if (!list_empty(&pcdev->active_bufs)) {
+ buf = list_entry(pcdev->active_bufs.next,
+ struct mx2_buffer, vb.queue);
+
+ BUG_ON(buf->bufnum != bufnum);
+
+ vb = &buf->vb;
+#ifdef DEBUG
+ phys = videobuf_to_dma_contig(vb);
+ if (readl(pcdev->base_emma + PRP_DEST_RGB1_PTR + 4 * bufnum)
+ != phys) {
+ dev_err(pcdev->dev, "%p != %p\n", phys,
+ readl(pcdev->base_emma +
+ PRP_DEST_RGB1_PTR +
+ 4 * bufnum));
+ }
+#endif
+ dev_dbg(pcdev->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, vb,
+ vb->baddr, vb->bsize);
+
+ list_del(&vb->queue);
+ vb->state = state;
+ do_gettimeofday(&vb->ts);
+ vb->field_count++;
+
+ wake_up(&vb->done);
+ }
+
+ if (list_empty(&pcdev->capture)) {
+ writel(pcdev->discard_buffer_dma, pcdev->base_emma +
+ PRP_DEST_RGB1_PTR + 4 * bufnum);
+ return;
+ }
+
+ buf = list_entry(pcdev->capture.next,
+ struct mx2_buffer, vb.queue);
+
+ buf->bufnum = bufnum;
+
+ list_move_tail(pcdev->capture.next, &pcdev->active_bufs);
+
+ vb = &buf->vb;
+ vb->state = VIDEOBUF_ACTIVE;
+
+ phys = videobuf_to_dma_contig(vb);
+ writel(phys, pcdev->base_emma + PRP_DEST_RGB1_PTR + 4 * bufnum);
+}
+
+static irqreturn_t mx27_camera_emma_irq(int irq_emma, void *data)
+{
+ struct mx2_camera_dev *pcdev = data;
+ unsigned int status = readl(pcdev->base_emma + PRP_INTRSTATUS);
+ struct mx2_buffer *buf;
+
+ if (status & (1 << 7)) { /* overflow */
+ u32 cntl;
+ /*
+ * We only disable channel 1 here since this is the only
+ * enabled channel
+ *
+ * FIXME: the correct DMA overflow handling should be resetting
+ * the buffer, returning an error frame, and continuing with
+ * the next one.
+ */
+ cntl = readl(pcdev->base_emma + PRP_CNTL);
+ writel(cntl & ~PRP_CNTL_CH1EN, pcdev->base_emma + PRP_CNTL);
+ writel(cntl, pcdev->base_emma + PRP_CNTL);
+ }
+ if ((status & (3 << 5)) == (3 << 5)
+ && !list_empty(&pcdev->active_bufs)) {
+ /*
+ * Both buffers have triggered, process the one we're expecting
+ * to first
+ */
+ buf = list_entry(pcdev->active_bufs.next,
+ struct mx2_buffer, vb.queue);
+ mx27_camera_frame_done_emma(pcdev, buf->bufnum, VIDEOBUF_DONE);
+ status &= ~(1 << (6 - buf->bufnum)); /* mark processed */
+ }
+ if (status & (1 << 6))
+ mx27_camera_frame_done_emma(pcdev, 0, VIDEOBUF_DONE);
+ if (status & (1 << 5))
+ mx27_camera_frame_done_emma(pcdev, 1, VIDEOBUF_DONE);
+
+ writel(status, pcdev->base_emma + PRP_INTRSTATUS);
+
+ return IRQ_HANDLED;
+}
+
+static int __devinit mx27_camera_emma_init(struct mx2_camera_dev *pcdev)
+{
+ struct resource *res_emma = pcdev->res_emma;
+ int err = 0;
+
+ if (!request_mem_region(res_emma->start, resource_size(res_emma),
+ MX2_CAM_DRV_NAME)) {
+ err = -EBUSY;
+ goto out;
+ }
+
+ pcdev->base_emma = ioremap(res_emma->start, resource_size(res_emma));
+ if (!pcdev->base_emma) {
+ err = -ENOMEM;
+ goto exit_release;
+ }
+
+ err = request_irq(pcdev->irq_emma, mx27_camera_emma_irq, 0,
+ MX2_CAM_DRV_NAME, pcdev);
+ if (err) {
+ dev_err(pcdev->dev, "Camera EMMA interrupt register failed \n");
+ goto exit_iounmap;
+ }
+
+ pcdev->clk_emma = clk_get(NULL, "emma");
+ if (IS_ERR(pcdev->clk_emma)) {
+ err = PTR_ERR(pcdev->clk_emma);
+ goto exit_free_irq;
+ }
+
+ clk_enable(pcdev->clk_emma);
+
+ err = mx27_camera_emma_prp_reset(pcdev);
+ if (err)
+ goto exit_clk_emma_put;
+
+ return err;
+
+exit_clk_emma_put:
+ clk_disable(pcdev->clk_emma);
+ clk_put(pcdev->clk_emma);
+exit_free_irq:
+ free_irq(pcdev->irq_emma, pcdev);
+exit_iounmap:
+ iounmap(pcdev->base_emma);
+exit_release:
+ release_mem_region(res_emma->start, resource_size(res_emma));
+out:
+ return err;
+}
+
+static int __devinit mx2_camera_probe(struct platform_device *pdev)
+{
+ struct mx2_camera_dev *pcdev;
+ struct resource *res_csi, *res_emma;
+ void __iomem *base_csi;
+ int irq_csi, irq_emma;
+ irq_handler_t mx2_cam_irq_handler = cpu_is_mx25() ? mx25_camera_irq
+ : mx27_camera_irq;
+ int err = 0;
+
+ dev_dbg(&pdev->dev, "initialising\n");
+
+ res_csi = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq_csi = platform_get_irq(pdev, 0);
+ if (res_csi == NULL || irq_csi < 0) {
+ dev_err(&pdev->dev, "Missing platform resources data\n");
+ err = -ENODEV;
+ goto exit;
+ }
+
+ pcdev = kzalloc(sizeof(*pcdev), GFP_KERNEL);
+ if (!pcdev) {
+ dev_err(&pdev->dev, "Could not allocate pcdev\n");
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ pcdev->clk_csi = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(pcdev->clk_csi)) {
+ err = PTR_ERR(pcdev->clk_csi);
+ goto exit_kfree;
+ }
+
+ dev_dbg(&pdev->dev, "Camera clock frequency: %ld\n",
+ clk_get_rate(pcdev->clk_csi));
+
+ /* Initialize DMA */
+#ifdef CONFIG_MACH_MX27
+ if (cpu_is_mx27()) {
+ err = mx27_camera_dma_init(pdev, pcdev);
+ if (err)
+ goto exit_clk_put;
+ }
+#endif /* CONFIG_MACH_MX27 */
+
+ pcdev->res_csi = res_csi;
+ pcdev->pdata = pdev->dev.platform_data;
+ if (pcdev->pdata) {
+ long rate;
+
+ pcdev->platform_flags = pcdev->pdata->flags;
+
+ rate = clk_round_rate(pcdev->clk_csi, pcdev->pdata->clk * 2);
+ if (rate <= 0) {
+ err = -ENODEV;
+ goto exit_dma_free;
+ }
+ err = clk_set_rate(pcdev->clk_csi, rate);
+ if (err < 0)
+ goto exit_dma_free;
+ }
+
+ INIT_LIST_HEAD(&pcdev->capture);
+ INIT_LIST_HEAD(&pcdev->active_bufs);
+ spin_lock_init(&pcdev->lock);
+
+ /*
+ * Request the regions.
+ */
+ if (!request_mem_region(res_csi->start, resource_size(res_csi),
+ MX2_CAM_DRV_NAME)) {
+ err = -EBUSY;
+ goto exit_dma_free;
+ }
+
+ base_csi = ioremap(res_csi->start, resource_size(res_csi));
+ if (!base_csi) {
+ err = -ENOMEM;
+ goto exit_release;
+ }
+ pcdev->irq_csi = irq_csi;
+ pcdev->base_csi = base_csi;
+ pcdev->base_dma = res_csi->start;
+ pcdev->dev = &pdev->dev;
+
+ err = request_irq(pcdev->irq_csi, mx2_cam_irq_handler, 0,
+ MX2_CAM_DRV_NAME, pcdev);
+ if (err) {
+ dev_err(pcdev->dev, "Camera interrupt register failed \n");
+ goto exit_iounmap;
+ }
+
+ if (cpu_is_mx27()) {
+ /* EMMA support */
+ res_emma = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ irq_emma = platform_get_irq(pdev, 1);
+
+ if (res_emma && irq_emma >= 0) {
+ dev_info(&pdev->dev, "Using EMMA\n");
+ pcdev->use_emma = 1;
+ pcdev->res_emma = res_emma;
+ pcdev->irq_emma = irq_emma;
+ if (mx27_camera_emma_init(pcdev))
+ goto exit_free_irq;
+ }
+ }
+
+ pcdev->soc_host.drv_name = MX2_CAM_DRV_NAME,
+ pcdev->soc_host.ops = &mx2_soc_camera_host_ops,
+ pcdev->soc_host.priv = pcdev;
+ pcdev->soc_host.v4l2_dev.dev = &pdev->dev;
+ pcdev->soc_host.nr = pdev->id;
+ err = soc_camera_host_register(&pcdev->soc_host);
+ if (err)
+ goto exit_free_emma;
+
+ return 0;
+
+exit_free_emma:
+ if (mx27_camera_emma(pcdev)) {
+ free_irq(pcdev->irq_emma, pcdev);
+ clk_disable(pcdev->clk_emma);
+ clk_put(pcdev->clk_emma);
+ iounmap(pcdev->base_emma);
+ release_mem_region(res_emma->start, resource_size(res_emma));
+ }
+exit_free_irq:
+ free_irq(pcdev->irq_csi, pcdev);
+exit_iounmap:
+ iounmap(base_csi);
+exit_release:
+ release_mem_region(res_csi->start, resource_size(res_csi));
+exit_dma_free:
+#ifdef CONFIG_MACH_MX27
+ if (cpu_is_mx27())
+ imx_dma_free(pcdev->dma);
+exit_clk_put:
+ clk_put(pcdev->clk_csi);
+#endif /* CONFIG_MACH_MX27 */
+exit_kfree:
+ kfree(pcdev);
+exit:
+ return err;
+}
+
+static int __devexit mx2_camera_remove(struct platform_device *pdev)
+{
+ struct soc_camera_host *soc_host = to_soc_camera_host(&pdev->dev);
+ struct mx2_camera_dev *pcdev = container_of(soc_host,
+ struct mx2_camera_dev, soc_host);
+ struct resource *res;
+
+ clk_put(pcdev->clk_csi);
+#ifdef CONFIG_MACH_MX27
+ if (cpu_is_mx27())
+ imx_dma_free(pcdev->dma);
+#endif /* CONFIG_MACH_MX27 */
+ free_irq(pcdev->irq_csi, pcdev);
+ if (mx27_camera_emma(pcdev))
+ free_irq(pcdev->irq_emma, pcdev);
+
+ soc_camera_host_unregister(&pcdev->soc_host);
+
+ iounmap(pcdev->base_csi);
+
+ if (mx27_camera_emma(pcdev)) {
+ clk_disable(pcdev->clk_emma);
+ clk_put(pcdev->clk_emma);
+ iounmap(pcdev->base_emma);
+ res = pcdev->res_emma;
+ release_mem_region(res->start, resource_size(res));
+ }
+
+ res = pcdev->res_csi;
+ release_mem_region(res->start, resource_size(res));
+
+ kfree(pcdev);
+
+ dev_info(&pdev->dev, "MX2 Camera driver unloaded\n");
+
+ return 0;
+}
+
+static struct platform_driver mx2_camera_driver = {
+ .driver = {
+ .name = MX2_CAM_DRV_NAME,
+ },
+ .remove = __devexit_p(mx2_camera_remove),
+};
+
+
+static int __init mx2_camera_init(void)
+{
+ return platform_driver_probe(&mx2_camera_driver, &mx2_camera_probe);
+}
+
+static void __exit mx2_camera_exit(void)
+{
+ return platform_driver_unregister(&mx2_camera_driver);
+}
+
+module_init(mx2_camera_init);
+module_exit(mx2_camera_exit);
+
+MODULE_DESCRIPTION("i.MX27/i.MX25 SoC Camera Host driver");
+MODULE_AUTHOR("Sascha Hauer <sha@pengutronix.de>");
+MODULE_LICENSE("GPL");
--
1.7.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCHv5] mx2_camera: Add soc_camera support for i.MX25/i.MX27
2010-07-01 11:03 [PATCHv5] mx2_camera: Add soc_camera support for i.MX25/i.MX27 Baruch Siach
@ 2010-07-01 12:28 ` Uwe Kleine-König
2010-07-01 14:01 ` Baruch Siach
2010-07-01 14:23 ` Guennadi Liakhovetski
0 siblings, 2 replies; 5+ messages in thread
From: Uwe Kleine-König @ 2010-07-01 12:28 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jul 01, 2010 at 02:03:19PM +0300, Baruch Siach wrote:
> This is the soc_camera support developed by Sascha Hauer for the i.MX27. Alan
> Carvalho de Assis modified the original driver to get it working on more recent
> kernels. I modified it further to add support for i.MX25. This driver has been
> tested on i.MX25 and i.MX27 based platforms.
>
> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
> Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
> ---
> Changes v4 -> v5
> Comments from Uwe Kleine-K?nig:
>
> Enclose mx27 DMA related stuff in #ifdefs since the dma-mx1-mx2.h is no
> longer accessible to mx25 builds
>
> s/MX2_VIDEO/VIDEO_MX2_HOSTSUPPORT/
>
> Changes v3 -> v4
> Address more comments from Guennadi Liakhovetski, including:
>
> * Fix the double trigger handling of mx27 eMMA
>
> * Add a FIXME comment in the code of eMMA overflow handling
>
> Changes v2 -> v3
> Address more comments from Guennadi Liakhovetski.
>
> Applied part of Sashca's patch that I forgot in v2.
>
> Changes v1 -> v2
> Addressed the comments of Guennadi Liakhovetski except from the following:
>
> 1. The mclk_get_divisor implementation, since I don't know what this code
> is good for
>
> 2. mx2_videobuf_release should not set pcdev->active on i.MX27, because
> mx27_camera_frame_done needs this pointer
>
> 3. In mx27_camera_emma_buf_init I don't know the meaning of those hard
> coded magic numbers
>
> Applied i.MX27 fixes from Sascha.
>
> arch/arm/plat-mxc/include/mach/memory.h | 4 +-
> arch/arm/plat-mxc/include/mach/mx2_cam.h | 46 +
> drivers/media/video/Kconfig | 13 +
> drivers/media/video/Makefile | 1 +
> drivers/media/video/mx2_camera.c | 1513 ++++++++++++++++++++++++++++++
> 5 files changed, 1575 insertions(+), 2 deletions(-)
> create mode 100644 arch/arm/plat-mxc/include/mach/mx2_cam.h
> create mode 100644 drivers/media/video/mx2_camera.c
>
> diff --git a/arch/arm/plat-mxc/include/mach/memory.h b/arch/arm/plat-mxc/include/mach/memory.h
> index c4b40c3..849d891 100644
> --- a/arch/arm/plat-mxc/include/mach/memory.h
> +++ b/arch/arm/plat-mxc/include/mach/memory.h
> @@ -44,12 +44,12 @@
> */
> #define CONSISTENT_DMA_SIZE SZ_8M
>
> -#elif defined(CONFIG_MX1_VIDEO)
> +#elif defined(CONFIG_MX1_VIDEO) || defined(CONFIG_VIDEO_MX2_HOSTSUPPORT)
> /*
> * Increase size of DMA-consistent memory region.
> * This is required for i.MX camera driver to capture at least four VGA frames.
> */
> #define CONSISTENT_DMA_SIZE SZ_4M
> -#endif /* CONFIG_MX1_VIDEO */
> +#endif /* CONFIG_MX1_VIDEO || CONFIG_MX2_VIDEO */
s/CONFIG_MX2_VIDEO/CONFIG_VIDEO_MX2_HOSTSUPPORT/ please
> #endif /* __ASM_ARCH_MXC_MEMORY_H__ */
> diff --git a/arch/arm/plat-mxc/include/mach/mx2_cam.h b/arch/arm/plat-mxc/include/mach/mx2_cam.h
> new file mode 100644
> index 0000000..3c080a3
> --- /dev/null
> +++ b/arch/arm/plat-mxc/include/mach/mx2_cam.h
Do you expect users of this header other than your driver? If not you
can fold it into the latter.
[...snip...]
> diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
> index bdbc9d3..27e2acc 100644
> --- a/drivers/media/video/Kconfig
> +++ b/drivers/media/video/Kconfig
> @@ -969,6 +969,19 @@ config VIDEO_OMAP2
> ---help---
> This is a v4l2 driver for the TI OMAP2 camera capture interface
>
> +config VIDEO_MX2_HOSTSUPPORT
> + bool
> +
> +config VIDEO_MX2
> + tristate "i.MX27/i.MX25 Camera Sensor Interface driver"
> + depends on VIDEO_DEV && SOC_CAMERA && (MACH_MX27 || ARCH_MX25)
> + select VIDEOBUF_DMA_CONTIG
CONTIG?
[...snap...]
> diff --git a/drivers/media/video/mx2_camera.c b/drivers/media/video/mx2_camera.c
> new file mode 100644
> index 0000000..98c93fa
> --- /dev/null
> +++ b/drivers/media/video/mx2_camera.c
> @@ -0,0 +1,1513 @@
[...snip...]
> +static int __devexit mx2_camera_remove(struct platform_device *pdev)
> +{
> + struct soc_camera_host *soc_host = to_soc_camera_host(&pdev->dev);
> + struct mx2_camera_dev *pcdev = container_of(soc_host,
> + struct mx2_camera_dev, soc_host);
> + struct resource *res;
> +
> + clk_put(pcdev->clk_csi);
> +#ifdef CONFIG_MACH_MX27
> + if (cpu_is_mx27())
> + imx_dma_free(pcdev->dma);
> +#endif /* CONFIG_MACH_MX27 */
> + free_irq(pcdev->irq_csi, pcdev);
> + if (mx27_camera_emma(pcdev))
> + free_irq(pcdev->irq_emma, pcdev);
> +
> + soc_camera_host_unregister(&pcdev->soc_host);
> +
> + iounmap(pcdev->base_csi);
> +
> + if (mx27_camera_emma(pcdev)) {
> + clk_disable(pcdev->clk_emma);
> + clk_put(pcdev->clk_emma);
> + iounmap(pcdev->base_emma);
> + res = pcdev->res_emma;
> + release_mem_region(res->start, resource_size(res));
> + }
> +
> + res = pcdev->res_csi;
> + release_mem_region(res->start, resource_size(res));
> +
> + kfree(pcdev);
> +
> + dev_info(&pdev->dev, "MX2 Camera driver unloaded\n");
> +
> + return 0;
> +}
> +
> +static struct platform_driver mx2_camera_driver = {
> + .driver = {
> + .name = MX2_CAM_DRV_NAME,
I'm always unsure if you need
.owner = THIS_MODULE,
here.
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCHv5] mx2_camera: Add soc_camera support for i.MX25/i.MX27
2010-07-01 12:28 ` Uwe Kleine-König
@ 2010-07-01 14:01 ` Baruch Siach
2010-07-01 14:23 ` Guennadi Liakhovetski
1 sibling, 0 replies; 5+ messages in thread
From: Baruch Siach @ 2010-07-01 14:01 UTC (permalink / raw)
To: linux-arm-kernel
Hi Uwe,
On Thu, Jul 01, 2010 at 02:28:03PM +0200, Uwe Kleine-K?nig wrote:
> On Thu, Jul 01, 2010 at 02:03:19PM +0300, Baruch Siach wrote:
> > This is the soc_camera support developed by Sascha Hauer for the i.MX27. Alan
> > Carvalho de Assis modified the original driver to get it working on more recent
> > kernels. I modified it further to add support for i.MX25. This driver has been
> > tested on i.MX25 and i.MX27 based platforms.
> >
> > Signed-off-by: Baruch Siach <baruch@tkos.co.il>
> > Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
> > ---
> > Changes v4 -> v5
> > Comments from Uwe Kleine-K?nig:
> >
> > Enclose mx27 DMA related stuff in #ifdefs since the dma-mx1-mx2.h is no
> > longer accessible to mx25 builds
> >
> > s/MX2_VIDEO/VIDEO_MX2_HOSTSUPPORT/
> >
> > Changes v3 -> v4
> > Address more comments from Guennadi Liakhovetski, including:
> >
> > * Fix the double trigger handling of mx27 eMMA
> >
> > * Add a FIXME comment in the code of eMMA overflow handling
> >
> > Changes v2 -> v3
> > Address more comments from Guennadi Liakhovetski.
> >
> > Applied part of Sashca's patch that I forgot in v2.
> >
> > Changes v1 -> v2
> > Addressed the comments of Guennadi Liakhovetski except from the following:
> >
> > 1. The mclk_get_divisor implementation, since I don't know what this code
> > is good for
> >
> > 2. mx2_videobuf_release should not set pcdev->active on i.MX27, because
> > mx27_camera_frame_done needs this pointer
> >
> > 3. In mx27_camera_emma_buf_init I don't know the meaning of those hard
> > coded magic numbers
> >
> > Applied i.MX27 fixes from Sascha.
> >
> > arch/arm/plat-mxc/include/mach/memory.h | 4 +-
> > arch/arm/plat-mxc/include/mach/mx2_cam.h | 46 +
> > drivers/media/video/Kconfig | 13 +
> > drivers/media/video/Makefile | 1 +
> > drivers/media/video/mx2_camera.c | 1513 ++++++++++++++++++++++++++++++
> > 5 files changed, 1575 insertions(+), 2 deletions(-)
> > create mode 100644 arch/arm/plat-mxc/include/mach/mx2_cam.h
> > create mode 100644 drivers/media/video/mx2_camera.c
> >
> > diff --git a/arch/arm/plat-mxc/include/mach/memory.h b/arch/arm/plat-mxc/include/mach/memory.h
> > index c4b40c3..849d891 100644
> > --- a/arch/arm/plat-mxc/include/mach/memory.h
> > +++ b/arch/arm/plat-mxc/include/mach/memory.h
> > @@ -44,12 +44,12 @@
> > */
> > #define CONSISTENT_DMA_SIZE SZ_8M
> >
> > -#elif defined(CONFIG_MX1_VIDEO)
> > +#elif defined(CONFIG_MX1_VIDEO) || defined(CONFIG_VIDEO_MX2_HOSTSUPPORT)
> > /*
> > * Increase size of DMA-consistent memory region.
> > * This is required for i.MX camera driver to capture at least four VGA frames.
> > */
> > #define CONSISTENT_DMA_SIZE SZ_4M
> > -#endif /* CONFIG_MX1_VIDEO */
> > +#endif /* CONFIG_MX1_VIDEO || CONFIG_MX2_VIDEO */
> s/CONFIG_MX2_VIDEO/CONFIG_VIDEO_MX2_HOSTSUPPORT/ please
Oops. Will fix.
> > #endif /* __ASM_ARCH_MXC_MEMORY_H__ */
> > diff --git a/arch/arm/plat-mxc/include/mach/mx2_cam.h b/arch/arm/plat-mxc/include/mach/mx2_cam.h
> > new file mode 100644
> > index 0000000..3c080a3
> > --- /dev/null
> > +++ b/arch/arm/plat-mxc/include/mach/mx2_cam.h
> Do you expect users of this header other than your driver? If not you
> can fold it into the latter.
This header contains mx2_camera_platform_data. Platform code needs this.
> [...snip...]
>
> > diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
> > index bdbc9d3..27e2acc 100644
> > --- a/drivers/media/video/Kconfig
> > +++ b/drivers/media/video/Kconfig
> > @@ -969,6 +969,19 @@ config VIDEO_OMAP2
> > ---help---
> > This is a v4l2 driver for the TI OMAP2 camera capture interface
> >
> > +config VIDEO_MX2_HOSTSUPPORT
> > + bool
> > +
> > +config VIDEO_MX2
> > + tristate "i.MX27/i.MX25 Camera Sensor Interface driver"
> > + depends on VIDEO_DEV && SOC_CAMERA && (MACH_MX27 || ARCH_MX25)
> > + select VIDEOBUF_DMA_CONTIG
> CONTIG?
This selects the physically contiguous DMA implementation of the videobuf API.
See drivers/media/video/videobuf-dma-contig.c.
> [...snap...]
>
> > diff --git a/drivers/media/video/mx2_camera.c b/drivers/media/video/mx2_camera.c
> > new file mode 100644
> > index 0000000..98c93fa
> > --- /dev/null
> > +++ b/drivers/media/video/mx2_camera.c
> > @@ -0,0 +1,1513 @@
>
> [...snip...]
>
> > +static int __devexit mx2_camera_remove(struct platform_device *pdev)
> > +{
> > + struct soc_camera_host *soc_host = to_soc_camera_host(&pdev->dev);
> > + struct mx2_camera_dev *pcdev = container_of(soc_host,
> > + struct mx2_camera_dev, soc_host);
> > + struct resource *res;
> > +
> > + clk_put(pcdev->clk_csi);
> > +#ifdef CONFIG_MACH_MX27
> > + if (cpu_is_mx27())
> > + imx_dma_free(pcdev->dma);
> > +#endif /* CONFIG_MACH_MX27 */
> > + free_irq(pcdev->irq_csi, pcdev);
> > + if (mx27_camera_emma(pcdev))
> > + free_irq(pcdev->irq_emma, pcdev);
> > +
> > + soc_camera_host_unregister(&pcdev->soc_host);
> > +
> > + iounmap(pcdev->base_csi);
> > +
> > + if (mx27_camera_emma(pcdev)) {
> > + clk_disable(pcdev->clk_emma);
> > + clk_put(pcdev->clk_emma);
> > + iounmap(pcdev->base_emma);
> > + res = pcdev->res_emma;
> > + release_mem_region(res->start, resource_size(res));
> > + }
> > +
> > + res = pcdev->res_csi;
> > + release_mem_region(res->start, resource_size(res));
> > +
> > + kfree(pcdev);
> > +
> > + dev_info(&pdev->dev, "MX2 Camera driver unloaded\n");
> > +
> > + return 0;
> > +}
> > +
> > +static struct platform_driver mx2_camera_driver = {
> > + .driver = {
> > + .name = MX2_CAM_DRV_NAME,
> I'm always unsure if you need
>
> .owner = THIS_MODULE,
>
> here.
It shouldn't heart. Will add.
baruch
--
~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- baruch at tkos.co.il - tel: +972.2.679.5364, http://www.tkos.co.il -
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCHv5] mx2_camera: Add soc_camera support for i.MX25/i.MX27
2010-07-01 12:28 ` Uwe Kleine-König
2010-07-01 14:01 ` Baruch Siach
@ 2010-07-01 14:23 ` Guennadi Liakhovetski
2010-07-01 14:46 ` Uwe Kleine-König
1 sibling, 1 reply; 5+ messages in thread
From: Guennadi Liakhovetski @ 2010-07-01 14:23 UTC (permalink / raw)
To: linux-arm-kernel
Hi Uwe
On Thu, 1 Jul 2010, Uwe Kleine-K?nig wrote:
> > diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
> > index bdbc9d3..27e2acc 100644
> > --- a/drivers/media/video/Kconfig
> > +++ b/drivers/media/video/Kconfig
> > @@ -969,6 +969,19 @@ config VIDEO_OMAP2
> > ---help---
> > This is a v4l2 driver for the TI OMAP2 camera capture interface
> >
> > +config VIDEO_MX2_HOSTSUPPORT
> > + bool
> > +
> > +config VIDEO_MX2
> > + tristate "i.MX27/i.MX25 Camera Sensor Interface driver"
> > + depends on VIDEO_DEV && SOC_CAMERA && (MACH_MX27 || ARCH_MX25)
> > + select VIDEOBUF_DMA_CONTIG
> CONTIG?
What exactly was your question here?
> > diff --git a/drivers/media/video/mx2_camera.c b/drivers/media/video/mx2_camera.c
> > new file mode 100644
> > index 0000000..98c93fa
> > --- /dev/null
> > +++ b/drivers/media/video/mx2_camera.c
> > @@ -0,0 +1,1513 @@
>
> [...snip...]
> > +static struct platform_driver mx2_camera_driver = {
> > + .driver = {
> > + .name = MX2_CAM_DRV_NAME,
> I'm always unsure if you need
>
> .owner = THIS_MODULE,
>
> here.
It is not needed in this case. See the "owner" field in struct
soc_camera_host_ops mx2_soc_camera_host_ops.
But that's not the reason why I'm replying. What I didn't like in these
your reviews, was the fact, that this driver has been submitted a number
of times to the arm-kernel ML, it has "mx2" in its subject, so, you had
enough chances to review it, just like Sascha did. Instead, you review it
now, making the author create new versions of his patch. You have been
asked for advise, because this patch potentially collided with other your
patches, your help in resolving this question is appreciated. But then you
suddenly decide to review the whole patch... Several of my patches have
been treated similarly in the past, so, I know how annoying it is to have
to re-iterate them because at v5 someone suddenly decided to take part in
the patch review process too...
Thanks
Guennadi
---
Guennadi Liakhovetski, Ph.D.
Freelance Open-Source Software Developer
http://www.open-technology.de/
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCHv5] mx2_camera: Add soc_camera support for i.MX25/i.MX27
2010-07-01 14:23 ` Guennadi Liakhovetski
@ 2010-07-01 14:46 ` Uwe Kleine-König
0 siblings, 0 replies; 5+ messages in thread
From: Uwe Kleine-König @ 2010-07-01 14:46 UTC (permalink / raw)
To: linux-arm-kernel
Hi Guennadi,
On Thu, Jul 01, 2010 at 04:23:23PM +0200, Guennadi Liakhovetski wrote:
> > > +config VIDEO_MX2
> > > + tristate "i.MX27/i.MX25 Camera Sensor Interface driver"
> > > + depends on VIDEO_DEV && SOC_CAMERA && (MACH_MX27 || ARCH_MX25)
> > > + select VIDEOBUF_DMA_CONTIG
> > CONTIG?
>
> What exactly was your question here?
I thought it to be a mistyped "CONFIG", I was wrong.
> > > diff --git a/drivers/media/video/mx2_camera.c b/drivers/media/video/mx2_camera.c
> > > new file mode 100644
> > > index 0000000..98c93fa
> > > --- /dev/null
> > > +++ b/drivers/media/video/mx2_camera.c
> > > @@ -0,0 +1,1513 @@
> >
> > [...snip...]
>
> > > +static struct platform_driver mx2_camera_driver = {
> > > + .driver = {
> > > + .name = MX2_CAM_DRV_NAME,
> > I'm always unsure if you need
> >
> > .owner = THIS_MODULE,
> >
> > here.
>
> It is not needed in this case. See the "owner" field in struct
> soc_camera_host_ops mx2_soc_camera_host_ops.
>
> But that's not the reason why I'm replying. What I didn't like in these
> your reviews, was the fact, that this driver has been submitted a number
> of times to the arm-kernel ML, it has "mx2" in its subject, so, you had
> enough chances to review it, just like Sascha did. Instead, you review it
> now, making the author create new versions of his patch. You have been
> asked for advise, because this patch potentially collided with other your
> patches, your help in resolving this question is appreciated. But then you
> suddenly decide to review the whole patch... Several of my patches have
> been treated similarly in the past, so, I know how annoying it is to have
> to re-iterate them because at v5 someone suddenly decided to take part in
> the patch review process too...
OK it might annoying but still I cannot understand why this is a reason to
lament. I don't necessarily feel part of the intended audience for each
patch on LAKML that contains mx2 in it's subject, still less if the
patch changes very little in arch/arm/{plat-mxc,arch-mx*} as Baruch's
patch does. Now he cc:d me and I had a look and even took the time to
point out the things that I noticed. From my POV a late reviewer is
better than getting code in that is less optimal. And let me point out
that reviewing sequentially is more efficient in the sum---at least for
the reviewers.
So should I ignore patches that are say already > v3?
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-K?nig |
Industrial Linux Solutions | http://www.pengutronix.de/ |
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2010-07-01 14:46 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-07-01 11:03 [PATCHv5] mx2_camera: Add soc_camera support for i.MX25/i.MX27 Baruch Siach
2010-07-01 12:28 ` Uwe Kleine-König
2010-07-01 14:01 ` Baruch Siach
2010-07-01 14:23 ` Guennadi Liakhovetski
2010-07-01 14:46 ` Uwe Kleine-König
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).