[PATCH 6/7] arm: plat-omap: system.h: move voiceblue definitions into the board header

[linux@arm.linux.org.uk (Russell King - ARM Linux)]

On Tue, Jan 18, 2011 at 09:52:44AM +0200, Aaro Koskinen wrote:
> Move voiceblue definitions into the board-specific header.
> 
> Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>

Let's instead simplify this, and allow other platforms to hook into the
reset handler if they choose.  This has only been build-tested on my
omap1 (which includes voiceblue) and omap4 configurations.

8<------
Subject: ARM: OMAP: Allow platforms to hook reset cleanly

This adds a clean method to allow platforms to hook into the reset
code if they require to.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-omap1/Makefile             |    2
 arch/arm/mach-omap1/board-voiceblue.c    |  106 +++++++++++++++++--------------
 arch/arm/mach-omap1/reset.c              |   25 +++++++
 arch/arm/mach-omap2/prcm.c               |    5 +
 arch/arm/plat-omap/include/plat/prcm.h   |    1
 arch/arm/plat-omap/include/plat/system.h |   38 -----------
 6 files changed, 91 insertions(+), 86 deletions(-)

diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile
index 6ee1950..148dc6b 100644
--- a/arch/arm/mach-omap1/Makefile
+++ b/arch/arm/mach-omap1/Makefile
@@ -4,7 +4,7 @@
 
 # Common support
 obj-y := io.o id.o sram.o irq.o mux.o flash.o serial.o devices.o dma.o
-obj-y += clock.o clock_data.o opp_data.o
+obj-y += clock.o clock_data.o opp_data.o reset.o
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index 815a69c..6712817 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -26,6 +26,7 @@
 #include <linux/smc91x.h>
 
 #include <mach/hardware.h>
+#include <mach/system.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -163,52 +164,6 @@ static void __init voiceblue_init_irq(void)
 	omap_init_irq();
 }
 
-static void __init voiceblue_init(void)
-{
-	/* mux pins for uarts */
-	omap_cfg_reg(UART1_TX);
-	omap_cfg_reg(UART1_RTS);
-	omap_cfg_reg(UART2_TX);
-	omap_cfg_reg(UART2_RTS);
-	omap_cfg_reg(UART3_TX);
-	omap_cfg_reg(UART3_RX);
-
-	/* Watchdog */
-	gpio_request(0, "Watchdog");
-	/* smc91x reset */
-	gpio_request(7, "SMC91x reset");
-	gpio_direction_output(7, 1);
-	udelay(2);	/* wait at least 100ns */
-	gpio_set_value(7, 0);
-	mdelay(50);	/* 50ms until PHY ready */
-	/* smc91x interrupt pin */
-	gpio_request(8, "SMC91x irq");
-	/* 16C554 reset*/
-	gpio_request(6, "16C554 reset");
-	gpio_direction_output(6, 0);
-	/* 16C554 interrupt pins */
-	gpio_request(12, "16C554 irq");
-	gpio_request(13, "16C554 irq");
-	gpio_request(14, "16C554 irq");
-	gpio_request(15, "16C554 irq");
-	set_irq_type(gpio_to_irq(12), IRQ_TYPE_EDGE_RISING);
-	set_irq_type(gpio_to_irq(13), IRQ_TYPE_EDGE_RISING);
-	set_irq_type(gpio_to_irq(14), IRQ_TYPE_EDGE_RISING);
-	set_irq_type(gpio_to_irq(15), IRQ_TYPE_EDGE_RISING);
-
-	platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
-	omap_board_config = voiceblue_config;
-	omap_board_config_size = ARRAY_SIZE(voiceblue_config);
-	omap_serial_init();
-	omap1_usb_init(&voiceblue_usb_config);
-	omap_register_i2c_bus(1, 100, NULL, 0);
-
-	/* There is a good chance board is going up, so enable power LED
-	 * (it is connected through invertor) */
-	omap_writeb(0x00, OMAP_LPG1_LCR);
-	omap_writeb(0x00, OMAP_LPG1_PMR);	/* Disable clock */
-}
-
 static void __init voiceblue_map_io(void)
 {
 	omap1_map_common_io();
@@ -275,8 +230,17 @@ void voiceblue_wdt_ping(void)
 	gpio_set_value(0, wdt_gpio_state);
 }
 
-void voiceblue_reset(void)
+static void voiceblue_reset(char mode, const char *cmd)
 {
+	/*
+	 * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
+	 * "Global Software Reset Affects Traffic Controller Frequency".
+	 */
+	if (cpu_is_omap5912()) {
+		omap_writew(omap_readw(DPLL_CTL) & ~(1 << 4), DPLL_CTL);
+		omap_writew(0x8, ARM_RSTCT1);
+	}
+
 	set_bit(MACHINE_REBOOT, &machine_state);
 	voiceblue_wdt_enable();
 	while (1) ;
@@ -286,6 +250,54 @@ EXPORT_SYMBOL(voiceblue_wdt_enable);
 EXPORT_SYMBOL(voiceblue_wdt_disable);
 EXPORT_SYMBOL(voiceblue_wdt_ping);
 
+static void __init voiceblue_init(void)
+{
+	/* mux pins for uarts */
+	omap_cfg_reg(UART1_TX);
+	omap_cfg_reg(UART1_RTS);
+	omap_cfg_reg(UART2_TX);
+	omap_cfg_reg(UART2_RTS);
+	omap_cfg_reg(UART3_TX);
+	omap_cfg_reg(UART3_RX);
+
+	/* Watchdog */
+	gpio_request(0, "Watchdog");
+	/* smc91x reset */
+	gpio_request(7, "SMC91x reset");
+	gpio_direction_output(7, 1);
+	udelay(2);	/* wait at least 100ns */
+	gpio_set_value(7, 0);
+	mdelay(50);	/* 50ms until PHY ready */
+	/* smc91x interrupt pin */
+	gpio_request(8, "SMC91x irq");
+	/* 16C554 reset*/
+	gpio_request(6, "16C554 reset");
+	gpio_direction_output(6, 0);
+	/* 16C554 interrupt pins */
+	gpio_request(12, "16C554 irq");
+	gpio_request(13, "16C554 irq");
+	gpio_request(14, "16C554 irq");
+	gpio_request(15, "16C554 irq");
+	set_irq_type(gpio_to_irq(12), IRQ_TYPE_EDGE_RISING);
+	set_irq_type(gpio_to_irq(13), IRQ_TYPE_EDGE_RISING);
+	set_irq_type(gpio_to_irq(14), IRQ_TYPE_EDGE_RISING);
+	set_irq_type(gpio_to_irq(15), IRQ_TYPE_EDGE_RISING);
+
+	platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
+	omap_board_config = voiceblue_config;
+	omap_board_config_size = ARRAY_SIZE(voiceblue_config);
+	omap_serial_init();
+	omap1_usb_init(&voiceblue_usb_config);
+	omap_register_i2c_bus(1, 100, NULL, 0);
+
+	/* There is a good chance board is going up, so enable power LED
+	 * (it is connected through invertor) */
+	omap_writeb(0x00, OMAP_LPG1_LCR);
+	omap_writeb(0x00, OMAP_LPG1_PMR);	/* Disable clock */
+
+	arch_reset = voiceblue_reset;
+}
+
 MACHINE_START(VOICEBLUE, "VoiceBlue OMAP5910")
 	/* Maintainer: Ladislav Michl <michl@2n.cz> */
 	.boot_params	= 0x10000100,
diff --git a/arch/arm/mach-omap1/reset.c b/arch/arm/mach-omap1/reset.c
index e69de29..ad951ee 100644
--- a/arch/arm/mach-omap1/reset.c
+++ b/arch/arm/mach-omap1/reset.c
@@ -0,0 +1,25 @@
+/*
+ * OMAP1 reset support
+ */
+#include <linux/kernel.h>
+#include <linux/io.h>
+
+#include <mach/hardware.h>
+#include <mach/system.h>
+#include <plat/prcm.h>
+
+void omap1_arch_reset(char mode, const char *cmd)
+{
+	/*
+	 * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
+	 * "Global Software Reset Affects Traffic Controller Frequency".
+	 */
+	if (cpu_is_omap5912()) {
+		omap_writew(omap_readw(DPLL_CTL) & ~(1 << 4), DPLL_CTL);
+		omap_writew(0x8, ARM_RSTCT1);
+	}
+
+	omap_writew(1, ARM_RSTCT1);
+}
+
+void (*arch_reset)(char, const char *) = omap1_arch_reset;
diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index 679bcd2..6be1438 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -24,6 +24,7 @@
 #include <linux/io.h>
 #include <linux/delay.h>
 
+#include <mach/system.h>
 #include <plat/common.h>
 #include <plat/prcm.h>
 #include <plat/irqs.h>
@@ -57,7 +58,7 @@ u32 omap_prcm_get_reset_sources(void)
 EXPORT_SYMBOL(omap_prcm_get_reset_sources);
 
 /* Resets clock rates and reboots the system. Only called from system.h */
-void omap_prcm_arch_reset(char mode, const char *cmd)
+static void omap_prcm_arch_reset(char mode, const char *cmd)
 {
 	s16 prcm_offs = 0;
 
@@ -108,6 +109,8 @@ void omap_prcm_arch_reset(char mode, const char *cmd)
 	omap2_prm_read_mod_reg(prcm_offs, OMAP2_RM_RSTCTRL); /* OCP barrier */
 }
 
+void (*arch_reset)(char, const char *) = omap_prcm_arch_reset;
+
 /**
  * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
  * @reg: physical address of module IDLEST register
diff --git a/arch/arm/plat-omap/include/plat/prcm.h b/arch/arm/plat-omap/include/plat/prcm.h
index 2fdf8c8..267f43b 100644
--- a/arch/arm/plat-omap/include/plat/prcm.h
+++ b/arch/arm/plat-omap/include/plat/prcm.h
@@ -28,7 +28,6 @@
 #define __ASM_ARM_ARCH_OMAP_PRCM_H
 
 u32 omap_prcm_get_reset_sources(void);
-void omap_prcm_arch_reset(char mode, const char *cmd);
 int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
 			 const char *name);
 
diff --git a/arch/arm/plat-omap/include/plat/system.h b/arch/arm/plat-omap/include/plat/system.h
index d0a119f..c5fa9e9 100644
--- a/arch/arm/plat-omap/include/plat/system.h
+++ b/arch/arm/plat-omap/include/plat/system.h
@@ -4,48 +4,14 @@
  */
 #ifndef __ASM_ARCH_SYSTEM_H
 #define __ASM_ARCH_SYSTEM_H
-#include <linux/clk.h>
 
-#include <asm/mach-types.h>
-#include <mach/hardware.h>
-
-#include <plat/prcm.h>
-
-#ifndef CONFIG_MACH_VOICEBLUE
-#define voiceblue_reset()		do {} while (0)
-#else
-extern void voiceblue_reset(void);
-#endif
+#include <asm/proc-fns.h>
 
 static inline void arch_idle(void)
 {
 	cpu_do_idle();
 }
 
-static inline void omap1_arch_reset(char mode, const char *cmd)
-{
-	/*
-	 * Workaround for 5912/1611b bug mentioned in sprz209d.pdf p. 28
-	 * "Global Software Reset Affects Traffic Controller Frequency".
-	 */
-	if (cpu_is_omap5912()) {
-		omap_writew(omap_readw(DPLL_CTL) & ~(1 << 4),
-				 DPLL_CTL);
-		omap_writew(0x8, ARM_RSTCT1);
-	}
-
-	if (machine_is_voiceblue())
-		voiceblue_reset();
-	else
-		omap_writew(1, ARM_RSTCT1);
-}
-
-static inline void arch_reset(char mode, const char *cmd)
-{
-	if (!cpu_class_is_omap2())
-		omap1_arch_reset(mode, cmd);
-	else
-		omap_prcm_arch_reset(mode, cmd);
-}
+extern void (*arch_reset)(char, const char *);
 
 #endif