From mboxrd@z Thu Jan 1 00:00:00 1970 From: cavokz@gmail.com (Domenico Andreoli) Date: Wed, 2 Feb 2011 22:06:37 +0000 Subject: [PATCH 2/2] ARM: QQ2440 networking support In-Reply-To: <20110202220530.GB2808@dandreoli.com> References: <20110202220359.GA2808@dandreoli.com> <20110202220530.GB2808@dandreoli.com> Message-ID: <20110202220637.GC2808@dandreoli.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org From: Domenico Andreoli Add networking support for QQ2440. Signed-off-by: Domenico Andreoli --- arch/arm/mach-s3c2440/include/mach/qq2440.h | 22 ++++++++++++ arch/arm/mach-s3c2440/mach-qq2440.c | 16 ++++++++ drivers/net/Kconfig | 4 +- drivers/net/cs89x0.c | 33 ++++++++++++------ 4 files changed, 61 insertions(+), 14 deletions(-) Index: arm-2.6.git/arch/arm/mach-s3c2440/include/mach/qq2440.h =================================================================== --- /dev/null 1970-01-01 00:00:00.000000000 +0000 +++ arm-2.6.git/arch/arm/mach-s3c2440/include/mach/qq2440.h 2011-02-02 18:32:38.000000000 +0000 @@ -0,0 +1,22 @@ +/* + * arch/arm/mach-s3c2440/include/mach/qq2440.h + * + * Copyright (c) 2011 Domenico Andreoli + * + * QQ2440 - platform definitions + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __ASM_MACH_QQ2440_H +#define __ASM_MACH_QQ2440_H + +#define QQ2440_CS8900_IRQ IRQ_EINT9 + +#define QQ2440_CS8900_VIRT_BASE S3C_ADDR(0x00500000) +#define QQ2440_CS8900_PA (S3C2410_CS3 + 0x1000000) +#define QQ2440_CS8900_SZ SZ_1M + +#endif /* __ASM_MACH_QQ2440_H */ Index: arm-2.6.git/drivers/net/cs89x0.c =================================================================== --- arm-2.6.git.orig/drivers/net/cs89x0.c 2011-02-02 18:28:01.000000000 +0000 +++ arm-2.6.git/drivers/net/cs89x0.c 2011-02-02 18:32:38.000000000 +0000 @@ -95,6 +95,9 @@ Dmitry Pervushin : dpervushin at ru.mvista.com : PNX010X platform support + Domenico Andreoli : cavokz at gmail.com + : QQ2440 platform support + */ /* Always include 'config.h' first in case the user wants to turn on @@ -117,7 +120,7 @@ * Set this to zero to remove all the debug statements via * dead code elimination */ -#define DEBUGGING 1 +#define DEBUGGING 0 /* Sources: @@ -173,6 +176,10 @@ #if defined(CONFIG_MACH_IXDP2351) static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0}; static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0}; +#elif defined(CONFIG_MACH_QQ2440) +#include +static unsigned int netcard_portlist[] __used __initdata = {QQ2440_CS8900_VIRT_BASE + 0x300, 0}; +static unsigned int cs8900_irq_map[] = {QQ2440_CS8900_IRQ, 0, 0, 0}; #elif defined(CONFIG_ARCH_IXDP2X01) static unsigned int netcard_portlist[] __used __initdata = {IXDP2X01_CS8900_VIRT_BASE, 0}; static unsigned int cs8900_irq_map[] = {IRQ_IXDP2X01_CS8900, 0, 0, 0}; @@ -521,6 +528,10 @@ #endif lp->force = g_cs89x0_media__force; #endif + +#if defined(CONFIG_MACH_QQ2440) + lp->force |= FORCE_RJ45 | FORCE_FULL; +#endif } /* Grab the region so we can find another board if autoIRQ fails. */ @@ -608,7 +619,7 @@ dev->dev_addr[i*2+1] = Addr >> 8; } - /* Load the Adapter Configuration. + /* Load the Adapter Configuration. Note: Barring any more specific information from some other source (ie EEPROM+Schematics), we would not know how to operate a 10Base2 interface on the AUI port. @@ -655,7 +666,7 @@ if ((readreg(dev, PP_SelfST) & EEPROM_PRESENT) == 0) printk(KERN_WARNING "cs89x0: No EEPROM, relying on command line....\n"); else if (get_eeprom_data(dev, START_EEPROM_DATA,CHKSUM_LEN,eeprom_buff) < 0) { - printk(KERN_WARNING "\ncs89x0: EEPROM read failed, relying on command line.\n"); + printk(KERN_WARNING "cs89x0: EEPROM read failed, relying on command line.\n"); } else if (get_eeprom_cksum(START_EEPROM_DATA,CHKSUM_LEN,eeprom_buff) < 0) { /* Check if the chip was able to read its own configuration starting @0 in the EEPROM*/ @@ -709,7 +720,7 @@ /* FIXME: we don't set the Ethernet address on the command line. Use ifconfig IFACE hw ether AABBCCDDEEFF */ - printk(KERN_INFO "cs89x0 media %s%s%s", + printk(KERN_INFO "cs89x0: media %s%s%s", (lp->adapter_cnf & A_CNF_10B_T)?"RJ-45,":"", (lp->adapter_cnf & A_CNF_AUI)?"AUI,":"", (lp->adapter_cnf & A_CNF_10B_2)?"BNC,":""); @@ -943,7 +954,7 @@ static void __init reset_chip(struct net_device *dev) { #if !defined(CONFIG_MACH_MX31ADS) -#if !defined(CONFIG_MACH_IXDP2351) && !defined(CONFIG_ARCH_IXDP2X01) +#if !defined(CS89x0_NONISA_IRQ) struct net_local *lp = netdev_priv(dev); int ioaddr = dev->base_addr; #endif @@ -954,18 +965,18 @@ /* wait 30 ms */ msleep(30); -#if !defined(CONFIG_MACH_IXDP2351) && !defined(CONFIG_ARCH_IXDP2X01) +#if !defined(CS89x0_NONISA_IRQ) if (lp->chip_type != CS8900) { /* Hardware problem requires PNP registers to be reconfigured after a reset */ writeword(ioaddr, ADD_PORT, PP_CS8920_ISAINT); - outb(dev->irq, ioaddr + DATA_PORT); - outb(0, ioaddr + DATA_PORT + 1); + writeword(ioaddr, DATA_PORT, dev->irq); + writeword(ioaddr, DATA_PORT + 1, 0); writeword(ioaddr, ADD_PORT, PP_CS8920_ISAMemB); - outb((dev->mem_start >> 16) & 0xff, ioaddr + DATA_PORT); - outb((dev->mem_start >> 8) & 0xff, ioaddr + DATA_PORT + 1); + writeword(ioaddr, DATA_PORT, (dev->mem_start >> 16) & 0xff); + writeword(ioaddr, DATA_PORT + 1, (dev->mem_start >> 8) & 0xff); } -#endif /* IXDP2x01 */ +#endif /* Wait until the chip is reset */ reset_start_time = jiffies; Index: arm-2.6.git/drivers/net/Kconfig =================================================================== --- arm-2.6.git.orig/drivers/net/Kconfig 2011-02-02 18:28:01.000000000 +0000 +++ arm-2.6.git/drivers/net/Kconfig 2011-02-02 18:32:38.000000000 +0000 @@ -1498,7 +1498,7 @@ config CS89x0 tristate "CS89x0 support" depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \ - || ARCH_IXDP2X01 || MACH_MX31ADS) + || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440) ---help--- Support for CS89x0 chipset based Ethernet cards. If you have a network (Ethernet) card of this type, say Y and read the @@ -1512,7 +1512,7 @@ config CS89x0_NONISA_IRQ def_bool y depends on CS89x0 != n - depends on MACH_IXDP2351 || ARCH_IXDP2X01 || MACH_MX31ADS + depends on MACH_IXDP2351 || ARCH_IXDP2X01 || MACH_MX31ADS || MACH_QQ2440 config TC35815 tristate "TOSHIBA TC35815 Ethernet support" Index: arm-2.6.git/arch/arm/mach-s3c2440/mach-qq2440.c =================================================================== --- arm-2.6.git.orig/arch/arm/mach-s3c2440/mach-qq2440.c 2011-02-02 18:29:48.000000000 +0000 +++ arm-2.6.git/arch/arm/mach-s3c2440/mach-qq2440.c 2011-02-02 18:32:38.000000000 +0000 @@ -36,6 +36,7 @@ #include #include #include +#include #include #include #include @@ -54,7 +55,12 @@ #include static struct map_desc qq2440_iodesc[] __initdata = { - /* nothing to declare, move along */ + { + .virtual = QQ2440_CS8900_VIRT_BASE, + .pfn = __phys_to_pfn(QQ2440_CS8900_PA), + .length = QQ2440_CS8900_SZ, + .type = MT_DEVICE + } }; #define UCON S3C2410_UCON_DEFAULT @@ -325,10 +331,18 @@ s3c24xx_init_uarts(qq2440_uartcfgs, ARRAY_SIZE(qq2440_uartcfgs)); } +#define QQ2440_CS8900_BANKCON (S3C2410_BANKCON_Tacp6 | S3C2410_BANKCON_Tcah4 | S3C2410_BANKCON_Tcoh1 | \ + S3C2410_BANKCON_Tacc14 | S3C2410_BANKCON_Tcos4) + static void __init qq2440_init(void) { int i; + /* Ethernet */ + __raw_writel(__raw_readl(S3C2410_BWSCON) | S3C2410_BWSCON_WS3 | S3C2410_BWSCON_ST3, S3C2410_BWSCON); + __raw_writel(QQ2440_CS8900_BANKCON, S3C2410_BANKCON3); + set_irq_type(QQ2440_CS8900_IRQ, IRQ_TYPE_EDGE_RISING); + /* Make sure the D+ pullup pin is output */ WARN_ON(gpio_request(S3C2410_GPG(12), "udc pup")); gpio_direction_output(S3C2410_GPG(12), 0);