[PATCH 4/4] spi/pl022: minor kerneldoc updates

[grant.likely@secretlab.ca (Grant Likely)]

On Tue, Feb 08, 2011 at 01:03:55PM +0100, Linus Walleij wrote:
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Applied, thanks.

g.

> ---
>  drivers/spi/amba-pl022.c |   25 ++++++++++++++++---------
>  1 files changed, 16 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/spi/amba-pl022.c b/drivers/spi/amba-pl022.c
> index 2b591f0..4cd05cc 100644
> --- a/drivers/spi/amba-pl022.c
> +++ b/drivers/spi/amba-pl022.c
> @@ -329,15 +329,16 @@ struct vendor_data {
>  /**
>   * struct pl022 - This is the private SSP driver data structure
>   * @adev: AMBA device model hookup
> - * @vendor: Vendor data for the IP block
> - * @phybase: The physical memory where the SSP device resides
> - * @virtbase: The virtual memory where the SSP is mapped
> + * @vendor: vendor data for the IP block
> + * @phybase: the physical memory where the SSP device resides
> + * @virtbase: the virtual memory where the SSP is mapped
> + * @clk: outgoing clock "SPICLK" for the SPI bus
>   * @master: SPI framework hookup
>   * @master_info: controller-specific data from machine setup
> - * @regs: SSP controller register's virtual address
> - * @pump_messages: Work struct for scheduling work to the workqueue
> - * @lock: spinlock to syncronise access to driver data
>   * @workqueue: a workqueue on which any spi_message request is queued
> + * @pump_messages: work struct for scheduling work to the workqueue
> + * @queue_lock: spinlock to syncronise access to message queue
> + * @queue: message queue
>   * @busy: workqueue is busy
>   * @running: workqueue is running
>   * @pump_transfers: Tasklet used in Interrupt Transfer mode
> @@ -348,8 +349,14 @@ struct vendor_data {
>   * @tx_end: end position in TX buffer to be read
>   * @rx: current position in RX buffer to be written
>   * @rx_end: end position in RX buffer to be written
> - * @readingtype: the type of read currently going on
> - * @writingtype: the type or write currently going on
> + * @read: the type of read currently going on
> + * @write: the type of write currently going on
> + * @exp_fifo_level: expected FIFO level
> + * @dma_rx_channel: optional channel for RX DMA
> + * @dma_tx_channel: optional channel for TX DMA
> + * @sgt_rx: scattertable for the RX transfer
> + * @sgt_tx: scattertable for the TX transfer
> + * @dummypage: a dummy page used for driving data on the bus with DMA
>   */
>  struct pl022 {
>  	struct amba_device		*adev;
> @@ -397,8 +404,8 @@ struct pl022 {
>   * @cpsr: Value of Clock prescale register
>   * @n_bytes: how many bytes(power of 2) reqd for a given data width of client
>   * @enable_dma: Whether to enable DMA or not
> - * @write: function ptr to be used to write when doing xfer for this chip
>   * @read: function ptr to be used to read when doing xfer for this chip
> + * @write: function ptr to be used to write when doing xfer for this chip
>   * @cs_control: chip select callback provided by chip
>   * @xfer_type: polling/interrupt/DMA
>   *
> -- 
> 1.7.3.2
>