From: anarsoul@gmail.com (Vasily Khoruzhick)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 5/8] ARM: PXA: Z2: Add poweroff function
Date: Sat, 12 Mar 2011 10:06:12 +0200 [thread overview]
Message-ID: <201103121006.12614.anarsoul@gmail.com> (raw)
In-Reply-To: <201103120105.15474.marek.vasut@gmail.com>
On Saturday 12 March 2011 02:05:15 Marek Vasut wrote:
> > Well, it looks like memory content is not preserved, or something wrong
> > with bootloader. Anyway, it does not resume after deepsleep for some
> > reason, I can't check better, as I have no JTAG. Maybe you can
> > investigate this problem?
>
> But resume after deepsleep is unrelated to this patch.
I just want to say that without this patch you can't keep device in low-
powermode, and it can drain full battery in ~week when it's in sleep mode.
> > No need, I understand how it works, PSPR is null, so after u-boot loads
> > PSPR to pc it performs 'soft reset' (jumps to 0x0, to begin of NOR
> > flash), RCSR bits are already cleared, so it just boots kernel.
>
> The note in Table 18 -- Exit from sleep or deep-sleep doesn't clear or set
> this bit -- means PSPR might not be null if you use your
> deep-sleep-parapowerdown.
Ok, I can clear PSPR before going to deepsleep, would it be enough?
Regards
Vasily
next prev parent reply other threads:[~2011-03-12 8:06 UTC|newest]
Thread overview: 60+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-03-11 10:23 [PATCH 1/8] ARM: PXA: Z2: Use only power button as wake source Vasily Khoruzhick
2011-03-11 10:23 ` [PATCH 2/8] ARM: PXA: Z2: Enable OHCI on Zipit Z2 Vasily Khoruzhick
2011-03-11 14:56 ` [PATCH v2 " Vasily Khoruzhick
2011-03-11 21:42 ` Marek Vasut
2011-03-11 21:49 ` Vasily Khoruzhick
2011-03-11 21:50 ` Marek Vasut
2011-03-11 21:55 ` Vasily Khoruzhick
2011-03-11 22:13 ` Marek Vasut
2011-03-11 22:34 ` Vasily Khoruzhick
2011-03-12 0:07 ` Marek Vasut
2011-03-12 11:32 ` Vasily Khoruzhick
2011-03-12 13:28 ` Marek Vasut
2011-03-13 10:18 ` Pavel Machek
2011-03-13 12:29 ` Marek Vasut
2011-03-13 17:10 ` Pavel Machek
2011-03-13 18:34 ` Marek Vasut
2011-03-13 22:15 ` Vasily Khoruzhick
2011-03-11 21:41 ` [PATCH " Marek Vasut
2011-03-11 10:23 ` [PATCH 3/8] ARM: PXA: Z2: Fix battery pdata Vasily Khoruzhick
2011-03-11 21:39 ` Marek Vasut
2011-03-11 10:23 ` [PATCH 4/8] ARM: PXA: Z2: Add mtd partition with logo Vasily Khoruzhick
2011-03-11 21:39 ` Marek Vasut
2011-03-11 22:31 ` Vasily Khoruzhick
2011-03-12 0:05 ` Marek Vasut
2011-03-15 14:39 ` Pavel Machek
2011-03-16 14:11 ` Marek Vasut
2011-03-16 16:51 ` Pavel Machek
2011-03-11 10:23 ` [PATCH 5/8] ARM: PXA: Z2: Add poweroff function Vasily Khoruzhick
2011-03-11 21:39 ` Marek Vasut
2011-03-11 21:53 ` Vasily Khoruzhick
2011-03-11 22:08 ` Marek Vasut
2011-03-11 22:12 ` Vasily Khoruzhick
2011-03-11 22:16 ` Marek Vasut
2011-03-11 22:30 ` Vasily Khoruzhick
2011-03-12 0:05 ` Marek Vasut
2011-03-12 2:29 ` Eric Miao
2011-03-12 8:06 ` Vasily Khoruzhick [this message]
2011-03-12 11:06 ` Marek Vasut
2011-03-12 11:30 ` Vasily Khoruzhick
2011-03-12 13:16 ` Marek Vasut
2011-03-12 20:33 ` Vasily Khoruzhick
2011-03-12 20:35 ` Marek Vasut
2011-03-12 20:34 ` Vasily Khoruzhick
2011-03-12 22:29 ` Marek Vasut
2011-03-15 15:49 ` Eric Miao
2011-03-15 15:57 ` Vasily Khoruzhick
2011-03-15 16:42 ` Eric Miao
2011-03-15 20:11 ` [PATCH v2] " Vasily Khoruzhick
2011-07-05 6:58 ` Eric Miao
2011-03-15 14:41 ` [PATCH 5/8] " Pavel Machek
2011-03-11 10:23 ` [PATCH 6/8] ARM: PXA: Z2: Fix libertas init/tear down sequences Vasily Khoruzhick
2011-03-11 21:37 ` Marek Vasut
2011-03-11 21:41 ` Vasily Khoruzhick
2011-03-11 21:51 ` Marek Vasut
2011-03-11 10:23 ` [PATCH 7/8] ARM: PXA: Z2: Keep kbd backlight disabled by default Vasily Khoruzhick
2011-03-11 21:36 ` Marek Vasut
2011-03-11 10:23 ` [PATCH 8/8] ARM: PXA: Z2: Add default triggers for LEDs Vasily Khoruzhick
2011-03-11 21:36 ` Marek Vasut
2011-03-11 21:43 ` [PATCH 1/8] ARM: PXA: Z2: Use only power button as wake source Marek Vasut
2011-03-13 10:15 ` Pavel Machek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201103121006.12614.anarsoul@gmail.com \
--to=anarsoul@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).