[PATCH V3 2/2] MX53 Enable the AHCI SATA on MX53 LOCO

[u.kleine-koenig@pengutronix.de (Uwe Kleine-König)]

On Mon, Apr 11, 2011 at 04:05:53PM +0800, Richard Zhu wrote:
> Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
> ---
>  arch/arm/mach-mx5/board-mx53_loco.c |   76 +++++++++++++++++++++++++++++++++++
>  1 files changed, 76 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-mx5/board-mx53_loco.c b/arch/arm/mach-mx5/board-mx53_loco.c
> index 0a18f8d..489830a 100644
> --- a/arch/arm/mach-mx5/board-mx53_loco.c
> +++ b/arch/arm/mach-mx5/board-mx53_loco.c
> @@ -23,11 +23,13 @@
>  #include <linux/fec.h>
>  #include <linux/delay.h>
>  #include <linux/gpio.h>
> +#include <linux/ahci_platform.h>
this shouldn't be needed, as devices-common already #includes it.

>  
>  #include <mach/common.h>
>  #include <mach/hardware.h>
>  #include <mach/imx-uart.h>
>  #include <mach/iomux-mx53.h>
> +#include <mach/ahci_sata.h>
>  
>  #include <asm/mach-types.h>
>  #include <asm/mach/arch.h>
> @@ -38,6 +40,8 @@
>  
>  #define LOCO_FEC_PHY_RST		IMX_GPIO_NR(7, 6)
>  
> +static struct clk *sata_clk, *sata_ref_clk;
> +
>  static iomux_v3_cfg_t mx53_loco_pads[] = {
>  	/* FEC */
>  	MX53_PAD_FEC_MDC__FEC_MDC,
> @@ -203,6 +207,77 @@ static const struct imxi2c_platform_data mx53_loco_i2c_data __initconst = {
>  	.bitrate = 100000,
>  };
>  
> +/* HW Initialization, if return 0, initialization is successful. */
> +static int mx53_loco_sata_init(struct device *dev, void __iomem *addr)
> +{
> +	int ret = 0;
> +	struct clk *clk;
> +
> +	sata_clk = clk_get(dev, NULL);
> +	if (IS_ERR(sata_clk)) {
> +		dev_err(dev, "no sata clock.\n");
> +		return PTR_ERR(sata_clk);
> +	}
> +	ret = clk_enable(sata_clk);
> +	if (ret) {
> +		dev_err(dev, "can't enable sata clock.\n");
> +		clk_put(sata_clk);
> +		return ret;
> +	}
> +
> +	/* FSL IMX AHCI SATA uses the internal usb phy1 clk on loco */
> +	sata_ref_clk = clk_get(NULL, "usb_phy1");
> +	if (IS_ERR(sata_ref_clk)) {
> +		dev_err(dev, "no sata ref clock.\n");
> +		ret = PTR_ERR(sata_ref_clk);
> +		goto release_sata_clk;
> +	}
> +	ret = clk_enable(sata_ref_clk);
> +	if (ret) {
> +		dev_err(dev, "can't enable sata ref clock.\n");
> +		clk_put(sata_ref_clk);
> +		goto release_sata_clk;
> +	}
> +
> +	/* Get the AHB clock rate, and configure the TIMER1MS reg later */
> +	clk = clk_get(NULL, "ahb");
> +	if (IS_ERR(clk)) {
> +		dev_err(dev, "no ahb clock.\n");
> +		ret = PTR_ERR(clk);
> +		goto release_sata_ref_clk;
> +	}
> +
> +	sata_init(addr, clk);
> +
> +	clk = NULL;
This isn't needed. And ah, there is the clk_get. This looks all strange.
If sata_ref_clk is needed to have ahci working it should be enabled
automatically (maybe by making it a secondary clk?) Otherwise it's
always on. Same for sata_ref_clk -> sata_clk.

> +	return ret;
> +
> +release_sata_ref_clk:
> +	clk_disable(sata_ref_clk);
> +	clk_put(sata_ref_clk);
> +
> +release_sata_clk:
> +	clk_disable(sata_clk);
> +	clk_put(sata_clk);
> +
> +	clk = NULL;
not needed

> +	return ret;
> +}
> +
> +static void sata_exit(struct device *dev)
mx53_loco_sata_exit?

> +{
> +	clk_disable(sata_ref_clk);
> +	clk_put(sata_ref_clk);
> +
> +	clk_disable(sata_clk);
> +	clk_put(sata_clk);
> +}
> +
> +static struct ahci_platform_data sata_data = {
> +	.init = mx53_loco_sata_init,
> +	.exit = sata_exit,
> +};
> +
>  static void __init mx53_loco_board_init(void)
>  {
>  	mxc_iomux_v3_setup_multiple_pads(mx53_loco_pads,
> @@ -215,6 +290,7 @@ static void __init mx53_loco_board_init(void)
>  	imx53_add_imx_i2c(1, &mx53_loco_i2c_data);
>  	imx53_add_sdhci_esdhc_imx(0, NULL);
>  	imx53_add_sdhci_esdhc_imx(2, NULL);
> +	imx53_add_ahci_imx(0, &sata_data);
>  }

-- 
Pengutronix e.K.                           | Uwe Kleine-K?nig            |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |