From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: OMAP: Get rid of section mismatch warnings
Date: Thu, 26 May 2011 06:37:32 -0700 [thread overview]
Message-ID: <20110526133732.GD11352@atomide.com> (raw)
In-Reply-To: <4DDE4EEF.8070108@ti.com>
* Santosh Shilimkar <santosh.shilimkar@ti.com> [110526 05:56]:
> On 5/26/2011 6:30 PM, Silesh C V wrote:
> >Get rid of the following and 8 other similar section mismatch
> >warnings
> >
> I send this [1] patch a month back. It's still not considered
> though even after reminder.
>
> [1] https://patchwork.kernel.org/patch/684831/
Applying now into devel-fixes with additional fixes from Silesh.
Updated patch below.
Regards,
Tony
From: Santosh Shilimkar <santosh.shilimkar@ti.com>
Date: Mon, 4 Apr 2011 10:02:05 +0000
Subject: [PATCH] OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.o
The serial*_data should have been marked as __initdata as per
it's usage in the board files. Fix the same to remove the
section mismatch warnings caused by it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Silesh C V <silesh@ti.com>
[tony at atomide.com: updated with additional fixes from Silesh]
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 52dbdf3..c710ad5 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -622,19 +622,19 @@ static struct omap_device_pad serial3_pads[] __initdata = {
OMAP_MUX_MODE0),
};
-static struct omap_board_data serial1_data = {
+static struct omap_board_data serial1_data __initdata = {
.id = 0,
.pads = serial1_pads,
.pads_cnt = ARRAY_SIZE(serial1_pads),
};
-static struct omap_board_data serial2_data = {
+static struct omap_board_data serial2_data __initdata = {
.id = 1,
.pads = serial2_pads,
.pads_cnt = ARRAY_SIZE(serial2_pads),
};
-static struct omap_board_data serial3_data = {
+static struct omap_board_data serial3_data __initdata = {
.id = 2,
.pads = serial3_pads,
.pads_cnt = ARRAY_SIZE(serial3_pads),
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index ae3153c..da6c666 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -258,7 +258,7 @@ static struct gpio sdp4430_eth_gpios[] __initdata = {
{ ETH_KS8851_IRQ, GPIOF_IN, "eth_irq" },
};
-static int omap_ethernet_init(void)
+static int __init omap_ethernet_init(void)
{
int status;
@@ -672,19 +672,19 @@ static struct omap_device_pad serial4_pads[] __initdata = {
OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
};
-static struct omap_board_data serial2_data = {
+static struct omap_board_data serial2_data __initdata = {
.id = 1,
.pads = serial2_pads,
.pads_cnt = ARRAY_SIZE(serial2_pads),
};
-static struct omap_board_data serial3_data = {
+static struct omap_board_data serial3_data __initdata = {
.id = 2,
.pads = serial3_pads,
.pads_cnt = ARRAY_SIZE(serial3_pads),
};
-static struct omap_board_data serial4_data = {
+static struct omap_board_data serial4_data __initdata = {
.id = 3,
.pads = serial4_pads,
.pads_cnt = ARRAY_SIZE(serial4_pads),
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 5d7c0a3..2d52ee7 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -526,19 +526,19 @@ static struct omap_device_pad serial4_pads[] __initdata = {
OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
};
-static struct omap_board_data serial2_data = {
+static struct omap_board_data serial2_data __initdata = {
.id = 1,
.pads = serial2_pads,
.pads_cnt = ARRAY_SIZE(serial2_pads),
};
-static struct omap_board_data serial3_data = {
+static struct omap_board_data serial3_data __initdata = {
.id = 2,
.pads = serial3_pads,
.pads_cnt = ARRAY_SIZE(serial3_pads),
};
-static struct omap_board_data serial4_data = {
+static struct omap_board_data serial4_data __initdata = {
.id = 3,
.pads = serial4_pads,
.pads_cnt = ARRAY_SIZE(serial4_pads),
diff --git a/arch/arm/mach-omap2/board-zoom-display.c b/arch/arm/mach-omap2/board-zoom-display.c
index ce53e82..d826242 100644
--- a/arch/arm/mach-omap2/board-zoom-display.c
+++ b/arch/arm/mach-omap2/board-zoom-display.c
@@ -26,7 +26,7 @@ static struct gpio zoom_lcd_gpios[] __initdata = {
{ LCD_PANEL_QVGA_GPIO, GPIOF_OUT_INIT_HIGH, "lcd qvga" },
};
-static void zoom_lcd_panel_init(void)
+static void __init zoom_lcd_panel_init(void)
{
zoom_lcd_gpios[0].gpio = (omap_rev() > OMAP3430_REV_ES3_0) ?
LCD_PANEL_RESET_GPIO_PROD :
next prev parent reply other threads:[~2011-05-26 13:37 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-05-26 13:00 [PATCH] ARM: OMAP: Get rid of section mismatch warnings Silesh C V
2011-05-26 13:00 ` Santosh Shilimkar
2011-05-26 13:37 ` Tony Lindgren [this message]
2011-05-26 13:55 ` Russell King - ARM Linux
2011-05-27 10:54 ` Tony Lindgren
2011-05-27 20:51 ` Kevin Hilman
2011-05-26 14:09 ` Igor Grinberg
2011-05-27 10:54 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110526133732.GD11352@atomide.com \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).