[PATCH 1/3 v3] ARM Realview PCIX map include file changes

[arnd@arndb.de (Arnd Bergmann)]

On Monday 22 August 2011, Colin Tuckley wrote:
> This patch adds the memory map PCI support to the include
> files for the Realview Northbridge based boards.
> 
> Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
> Acked-by: Catalin Marinas <catalin.marinas@arm.com>

Hi Colin,

I think we've discussed this before. I think it's good to
have PCI support enabled in realview, but please do the
PIO window properly.

> diff --git a/arch/arm/mach-realview/include/mach/hardware.h b/arch/arm/mach-realview/include/mach/hardware.h
> index 8a638d1..dcc64f2 100644
> --- a/arch/arm/mach-realview/include/mach/hardware.h
> +++ b/arch/arm/mach-realview/include/mach/hardware.h
> +/*
> + * PCI space physical addresses and sizes
> + */
> +#define REALVIEW_PB_PCI_BASE		0x90040000	/* PCI-X Unit base */
> +#define REALVIEW_PB_PCI_BASE_SIZE	0x00010000	/* 4 Kb + 60Kb reserved */
> +#define REALVIEW_PB_PCI_IO_BASE		0x90050000	/* IO Region on AHB */
> +#define REALVIEW_PB_PCI_IO_SIZE		0x00010000	/* 64 Kb */
> +#define REALVIEW_PB_PCI_IO_LIMIT       (REALVIEW_PB_PCI_IO_BASE + REALVIEW_PB_PCI_IO_SIZE - 1)
> +#define REALVIEW_PB_PCI_MEM_BASE	0xA0000000	/* MEM Region on AHB */
> +#define REALVIEW_PB_PCI_MEM_SIZE	0x20000000	/* 512 MB */
> +
> +#define REALVIEW_ISSP_REG_BASE		0x100E3000

As you write here, the I/O window size is 64KB, which is totally normal
for PCI buses.

> +#ifdef CONFIG_PCI
> +#if !defined(__ASSEMBLY__)
> +static inline unsigned int pcibios_min_io(void)
> +{
> +	if (machine_is_realview_pb11mp() || machine_is_realview_pba8() ||
> +	    machine_is_realview_pbx())
> +		return REALVIEW_PB_PCI_IO_BASE;
> +	else
> +		return 0;
> +}

pcibios_min_io should be 0x1000 as a constant, in order to get the
ISA addresses out of the way, but there is no need to make it
board dependent.

> +static inline unsigned int pcibios_min_mem(void)
> +{
> +	if (machine_is_realview_pb11mp() || machine_is_realview_pba8() ||
> +	    machine_is_realview_pbx())
> +		return REALVIEW_PB_PCI_MEM_BASE;
> +	else
> +		return 0;
> +}
> +#endif

Just hardcode this to REALVIEW_PB_PCI_MEM_BASE

> diff --git a/arch/arm/mach-realview/include/mach/io.h b/arch/arm/mach-realview/include/mach/io.h
> index f05bcdf..aa97d18 100644
> --- a/arch/arm/mach-realview/include/mach/io.h
> +++ b/arch/arm/mach-realview/include/mach/io.h
> @@ -20,9 +20,25 @@
>  #ifndef __ASM_ARM_ARCH_IO_H
>  #define __ASM_ARM_ARCH_IO_H
>  
> +#include <asm/mach-types.h>
> +#include <mach/hardware.h>
> +
>  #define IO_SPACE_LIMIT 0xffffffff

The IO_SPACE_LIMIT should match the REALVIEW_PB_PCI_IO_BASE above.

> -#define __io(a)		__typesafe_io(a)
> +static inline void __iomem *__io(unsigned long addr)
> +{
> +#ifdef CONFIG_PCI
> +	/* check for PCI I/O space */
> +	if (addr >= REALVIEW_PB_PCI_IO_BASE && addr <= REALVIEW_PB_PCI_IO_LIMIT)
> +		return (void __iomem *)((addr - REALVIEW_PB_PCI_IO_BASE) + REALVIEW_PCI_IO_VBASE);
> +	else
> +		return (void __iomem *)addr;
> +#else
> +	return (void __iomem *)addr;
> +#endif
> +}

And there is no need to do these tricks when you only have a single
PCI bus. Just define the PIO window to be based on zero and 64K
in size, and hardcode that, to end up with

#define __io(a)  (REALVIEW_PCI_IO_VBASE + (a & IO_SPACE_LIMIT))

	Arnd