* [PATCH 01/11] at91/gpio: make gpio register base soc independant
@ 2011-09-19 12:51 Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 02/11] at91/boards: use -1 for invalid gpio Jean-Christophe PLAGNIOL-VILLARD
` (9 more replies)
0 siblings, 10 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 12:51 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
---
arch/arm/mach-at91/at91cap9.c | 8 ++++----
arch/arm/mach-at91/at91rm9200.c | 8 ++++----
arch/arm/mach-at91/at91sam9260.c | 6 +++---
arch/arm/mach-at91/at91sam9261.c | 6 +++---
arch/arm/mach-at91/at91sam9263.c | 10 +++++-----
arch/arm/mach-at91/at91sam9g45.c | 10 +++++-----
arch/arm/mach-at91/at91sam9rl.c | 8 ++++----
arch/arm/mach-at91/generic.h | 2 +-
arch/arm/mach-at91/gpio.c | 8 ++++++--
arch/arm/mach-at91/include/mach/at91cap9.h | 9 +++++----
arch/arm/mach-at91/include/mach/at91rm9200.h | 9 +++++----
arch/arm/mach-at91/include/mach/at91sam9260.h | 7 ++++---
arch/arm/mach-at91/include/mach/at91sam9261.h | 7 ++++---
arch/arm/mach-at91/include/mach/at91sam9263.h | 11 ++++++-----
arch/arm/mach-at91/include/mach/at91sam9g45.h | 11 ++++++-----
arch/arm/mach-at91/include/mach/at91sam9rl.h | 9 +++++----
16 files changed, 70 insertions(+), 59 deletions(-)
diff --git a/arch/arm/mach-at91/at91cap9.c b/arch/arm/mach-at91/at91cap9.c
index ecdd54d..fe00dce 100644
--- a/arch/arm/mach-at91/at91cap9.c
+++ b/arch/arm/mach-at91/at91cap9.c
@@ -296,19 +296,19 @@ void __init at91cap9_set_console_clock(int id)
static struct at91_gpio_bank at91cap9_gpio[] = {
{
.id = AT91CAP9_ID_PIOABCD,
- .offset = AT91_PIOA,
+ .regbase = AT91CAP9_BASE_PIOA,
.clock = &pioABCD_clk,
}, {
.id = AT91CAP9_ID_PIOABCD,
- .offset = AT91_PIOB,
+ .regbase = AT91CAP9_BASE_PIOB,
.clock = &pioABCD_clk,
}, {
.id = AT91CAP9_ID_PIOABCD,
- .offset = AT91_PIOC,
+ .regbase = AT91CAP9_BASE_PIOC,
.clock = &pioABCD_clk,
}, {
.id = AT91CAP9_ID_PIOABCD,
- .offset = AT91_PIOD,
+ .regbase = AT91CAP9_BASE_PIOD,
.clock = &pioABCD_clk,
}
};
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index 713d3bd..8ce8675 100644
--- a/arch/arm/mach-at91/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -271,19 +271,19 @@ void __init at91rm9200_set_console_clock(int id)
static struct at91_gpio_bank at91rm9200_gpio[] = {
{
.id = AT91RM9200_ID_PIOA,
- .offset = AT91_PIOA,
+ .regbase = AT91RM9200_BASE_PIOA,
.clock = &pioA_clk,
}, {
.id = AT91RM9200_ID_PIOB,
- .offset = AT91_PIOB,
+ .regbase = AT91RM9200_BASE_PIOB,
.clock = &pioB_clk,
}, {
.id = AT91RM9200_ID_PIOC,
- .offset = AT91_PIOC,
+ .regbase = AT91RM9200_BASE_PIOC,
.clock = &pioC_clk,
}, {
.id = AT91RM9200_ID_PIOD,
- .offset = AT91_PIOD,
+ .regbase = AT91RM9200_BASE_PIOD,
.clock = &pioD_clk,
}
};
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index a9be758..d7ad3e0 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -265,15 +265,15 @@ void __init at91sam9260_set_console_clock(int id)
static struct at91_gpio_bank at91sam9260_gpio[] = {
{
.id = AT91SAM9260_ID_PIOA,
- .offset = AT91_PIOA,
+ .regbase = AT91SAM9260_BASE_PIOA,
.clock = &pioA_clk,
}, {
.id = AT91SAM9260_ID_PIOB,
- .offset = AT91_PIOB,
+ .regbase = AT91SAM9260_BASE_PIOB,
.clock = &pioB_clk,
}, {
.id = AT91SAM9260_ID_PIOC,
- .offset = AT91_PIOC,
+ .regbase = AT91SAM9260_BASE_PIOC,
.clock = &pioC_clk,
}
};
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index 658a518..574aa6b 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -254,15 +254,15 @@ void __init at91sam9261_set_console_clock(int id)
static struct at91_gpio_bank at91sam9261_gpio[] = {
{
.id = AT91SAM9261_ID_PIOA,
- .offset = AT91_PIOA,
+ .regbase = AT91SAM9261_BASE_PIOA,
.clock = &pioA_clk,
}, {
.id = AT91SAM9261_ID_PIOB,
- .offset = AT91_PIOB,
+ .regbase = AT91SAM9261_BASE_PIOB,
.clock = &pioB_clk,
}, {
.id = AT91SAM9261_ID_PIOC,
- .offset = AT91_PIOC,
+ .regbase = AT91SAM9261_BASE_PIOC,
.clock = &pioC_clk,
}
};
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index f83fbb0..dee0ed7 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -266,23 +266,23 @@ void __init at91sam9263_set_console_clock(int id)
static struct at91_gpio_bank at91sam9263_gpio[] = {
{
.id = AT91SAM9263_ID_PIOA,
- .offset = AT91_PIOA,
+ .regbase = AT91SAM9263_BASE_PIOA,
.clock = &pioA_clk,
}, {
.id = AT91SAM9263_ID_PIOB,
- .offset = AT91_PIOB,
+ .regbase = AT91SAM9263_BASE_PIOB,
.clock = &pioB_clk,
}, {
.id = AT91SAM9263_ID_PIOCDE,
- .offset = AT91_PIOC,
+ .regbase = AT91SAM9263_BASE_PIOC,
.clock = &pioCDE_clk,
}, {
.id = AT91SAM9263_ID_PIOCDE,
- .offset = AT91_PIOD,
+ .regbase = AT91SAM9263_BASE_PIOD,
.clock = &pioCDE_clk,
}, {
.id = AT91SAM9263_ID_PIOCDE,
- .offset = AT91_PIOE,
+ .regbase = AT91SAM9263_BASE_PIOE,
.clock = &pioCDE_clk,
}
};
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index 8f5db7b..753df63 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -282,23 +282,23 @@ void __init at91sam9g45_set_console_clock(int id)
static struct at91_gpio_bank at91sam9g45_gpio[] = {
{
.id = AT91SAM9G45_ID_PIOA,
- .offset = AT91_PIOA,
+ .regbase = AT91SAM9G45_BASE_PIOA,
.clock = &pioA_clk,
}, {
.id = AT91SAM9G45_ID_PIOB,
- .offset = AT91_PIOB,
+ .regbase = AT91SAM9G45_BASE_PIOB,
.clock = &pioB_clk,
}, {
.id = AT91SAM9G45_ID_PIOC,
- .offset = AT91_PIOC,
+ .regbase = AT91SAM9G45_BASE_PIOC,
.clock = &pioC_clk,
}, {
.id = AT91SAM9G45_ID_PIODE,
- .offset = AT91_PIOD,
+ .regbase = AT91SAM9G45_BASE_PIOD,
.clock = &pioDE_clk,
}, {
.id = AT91SAM9G45_ID_PIODE,
- .offset = AT91_PIOE,
+ .regbase = AT91SAM9G45_BASE_PIOE,
.clock = &pioDE_clk,
}
};
diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c
index a238105..c4004e2 100644
--- a/arch/arm/mach-at91/at91sam9rl.c
+++ b/arch/arm/mach-at91/at91sam9rl.c
@@ -246,19 +246,19 @@ void __init at91sam9rl_set_console_clock(int id)
static struct at91_gpio_bank at91sam9rl_gpio[] = {
{
.id = AT91SAM9RL_ID_PIOA,
- .offset = AT91_PIOA,
+ .regbase = AT91SAM9RL_BASE_PIOA,
.clock = &pioA_clk,
}, {
.id = AT91SAM9RL_ID_PIOB,
- .offset = AT91_PIOB,
+ .regbase = AT91SAM9RL_BASE_PIOB,
.clock = &pioB_clk,
}, {
.id = AT91SAM9RL_ID_PIOC,
- .offset = AT91_PIOC,
+ .regbase = AT91SAM9RL_BASE_PIOC,
.clock = &pioC_clk,
}, {
.id = AT91SAM9RL_ID_PIOD,
- .offset = AT91_PIOD,
+ .regbase = AT91SAM9RL_BASE_PIOD,
.clock = &pioD_clk,
}
};
diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h
index 938b34f..11d7297 100644
--- a/arch/arm/mach-at91/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -65,7 +65,7 @@ extern void at91sam9_alt_reset(void);
struct at91_gpio_bank {
unsigned short id; /* peripheral ID */
- unsigned long offset; /* offset from system peripheral base */
+ unsigned long regbase; /* offset from system peripheral base */
struct clk *clock; /* associated clock */
};
extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks);
diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c
index 4615528..04beff1 100644
--- a/arch/arm/mach-at91/gpio.c
+++ b/arch/arm/mach-at91/gpio.c
@@ -616,8 +616,12 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
at91_gpio->bank = &data[i];
at91_gpio->chip.base = PIN_BASE + i * 32;
- at91_gpio->regbase = at91_gpio->bank->offset +
- (void __iomem *)AT91_VA_BASE_SYS;
+
+ at91_gpio->regbase = ioremap(at91_gpio->bank->regbase, 512);
+ if (!at91_gpio->regbase) {
+ pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", i);
+ continue;
+ }
/* enable PIO controller's clock */
clk_enable(at91_gpio->bank->clock);
diff --git a/arch/arm/mach-at91/include/mach/at91cap9.h b/arch/arm/mach-at91/include/mach/at91cap9.h
index c5df1e8..f65d083 100644
--- a/arch/arm/mach-at91/include/mach/at91cap9.h
+++ b/arch/arm/mach-at91/include/mach/at91cap9.h
@@ -88,10 +88,6 @@
#define AT91_DMA (0xffffec00 - AT91_BASE_SYS)
#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS)
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
@@ -102,6 +98,11 @@
(0xfffffd50 - AT91_BASE_SYS) : \
(0xfffffd60 - AT91_BASE_SYS))
+#define AT91CAP9_BASE_PIOA 0xfffff200
+#define AT91CAP9_BASE_PIOB 0xfffff400
+#define AT91CAP9_BASE_PIOC 0xfffff600
+#define AT91CAP9_BASE_PIOD 0xfffff800
+
#define AT91_USART0 AT91CAP9_BASE_US0
#define AT91_USART1 AT91CAP9_BASE_US1
#define AT91_USART2 AT91CAP9_BASE_US2
diff --git a/arch/arm/mach-at91/include/mach/at91rm9200.h b/arch/arm/mach-at91/include/mach/at91rm9200.h
index e4037b5..5740954 100644
--- a/arch/arm/mach-at91/include/mach/at91rm9200.h
+++ b/arch/arm/mach-at91/include/mach/at91rm9200.h
@@ -81,15 +81,16 @@
*/
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) /* Advanced Interrupt Controller */
#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) /* Debug Unit */
-#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) /* PIO Controller A */
-#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) /* PIO Controller B */
-#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) /* PIO Controller C */
-#define AT91_PIOD (0xfffffa00 - AT91_BASE_SYS) /* PIO Controller D */
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) /* Power Management Controller */
#define AT91_ST (0xfffffd00 - AT91_BASE_SYS) /* System Timer */
#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS) /* Real-Time Clock */
#define AT91_MC (0xffffff00 - AT91_BASE_SYS) /* Memory Controllers */
+#define AT91RM9200_BASE_PIOA 0xfffff400 /* PIO Controller A */
+#define AT91RM9200_BASE_PIOB 0xfffff600 /* PIO Controller B */
+#define AT91RM9200_BASE_PIOC 0xfffff800 /* PIO Controller C */
+#define AT91RM9200_BASE_PIOD 0xfffffa00 /* PIO Controller D */
+
#define AT91_USART0 AT91RM9200_BASE_US0
#define AT91_USART1 AT91RM9200_BASE_US1
#define AT91_USART2 AT91RM9200_BASE_US2
diff --git a/arch/arm/mach-at91/include/mach/at91sam9260.h b/arch/arm/mach-at91/include/mach/at91sam9260.h
index 9a79116..1bea3dc 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9260.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9260.h
@@ -87,9 +87,6 @@
#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS)
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
@@ -98,6 +95,10 @@
#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
+#define AT91SAM9260_BASE_PIOA 0xfffff400
+#define AT91SAM9260_BASE_PIOB 0xfffff600
+#define AT91SAM9260_BASE_PIOC 0xfffff800
+
#define AT91_USART0 AT91SAM9260_BASE_US0
#define AT91_USART1 AT91SAM9260_BASE_US1
#define AT91_USART2 AT91SAM9260_BASE_US2
diff --git a/arch/arm/mach-at91/include/mach/at91sam9261.h b/arch/arm/mach-at91/include/mach/at91sam9261.h
index ce59620..17ae9c7 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9261.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9261.h
@@ -70,9 +70,6 @@
#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
@@ -81,6 +78,10 @@
#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS)
+#define AT91SAM9261_BASE_PIOA 0xfffff400
+#define AT91SAM9261_BASE_PIOB 0xfffff600
+#define AT91SAM9261_BASE_PIOC 0xfffff800
+
#define AT91_USART0 AT91SAM9261_BASE_US0
#define AT91_USART1 AT91SAM9261_BASE_US1
#define AT91_USART2 AT91SAM9261_BASE_US2
diff --git a/arch/arm/mach-at91/include/mach/at91sam9263.h b/arch/arm/mach-at91/include/mach/at91sam9263.h
index f1b9296..dd54079 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9263.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9263.h
@@ -84,11 +84,6 @@
#define AT91_CCFG (0xffffed10 - AT91_BASE_SYS)
#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS)
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOE (0xfffffa00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
@@ -98,6 +93,12 @@
#define AT91_RTT1 (0xfffffd50 - AT91_BASE_SYS)
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
+#define AT91SAM9263_BASE_PIOA 0xfffff200
+#define AT91SAM9263_BASE_PIOB 0xfffff400
+#define AT91SAM9263_BASE_PIOC 0xfffff600
+#define AT91SAM9263_BASE_PIOD 0xfffff800
+#define AT91SAM9263_BASE_PIOE 0xfffffa00
+
#define AT91_USART0 AT91SAM9263_BASE_US0
#define AT91_USART1 AT91SAM9263_BASE_US1
#define AT91_USART2 AT91SAM9263_BASE_US2
diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45.h b/arch/arm/mach-at91/include/mach/at91sam9g45.h
index 2c611b9..ec370cc 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9g45.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9g45.h
@@ -94,11 +94,6 @@
#define AT91_DMA (0xffffec00 - AT91_BASE_SYS)
#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS)
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOE (0xfffffa00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
@@ -108,6 +103,12 @@
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
#define AT91_RTC (0xfffffdb0 - AT91_BASE_SYS)
+#define AT91SAM9G45_BASE_PIOA 0xfffff200
+#define AT91SAM9G45_BASE_PIOB 0xfffff400
+#define AT91SAM9G45_BASE_PIOC 0xfffff600
+#define AT91SAM9G45_BASE_PIOD 0xfffff800
+#define AT91SAM9G45_BASE_PIOE 0xfffffa00
+
#define AT91_USART0 AT91SAM9G45_BASE_US0
#define AT91_USART1 AT91SAM9G45_BASE_US1
#define AT91_USART2 AT91SAM9G45_BASE_US2
diff --git a/arch/arm/mach-at91/include/mach/at91sam9rl.h b/arch/arm/mach-at91/include/mach/at91sam9rl.h
index 1aabacd..d3ef11a 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9rl.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9rl.h
@@ -77,10 +77,6 @@
#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS)
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOD (0xfffffa00 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS)
@@ -91,6 +87,11 @@
#define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS)
#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS)
+#define AT91SAM9RL_BASE_PIOA 0xfffff400
+#define AT91SAM9RL_BASE_PIOB 0xfffff600
+#define AT91SAM9RL_BASE_PIOC 0xfffff800
+#define AT91SAM9RL_BASE_PIOD 0xfffffa00
+
#define AT91_USART0 AT91SAM9RL_BASE_US0
#define AT91_USART1 AT91SAM9RL_BASE_US1
#define AT91_USART2 AT91SAM9RL_BASE_US2
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 02/11] at91/boards: use -1 for invalid gpio
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 12:51 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-21 9:28 ` Nicolas Ferre
2011-09-19 12:51 ` [PATCH 03/11] at91/soc: use gpio_is_valid to check the gpio Jean-Christophe PLAGNIOL-VILLARD
` (8 subsequent siblings)
9 siblings, 1 reply; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 12:51 UTC (permalink / raw)
To: linux-arm-kernel
this will allow to use gpio_is_valid
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/mach-at91/board-1arm.c | 1 +
arch/arm/mach-at91/board-afeb-9260v1.c | 7 ++++++-
arch/arm/mach-at91/board-cam60.c | 3 ++-
arch/arm/mach-at91/board-cap9adk.c | 14 ++++++++------
arch/arm/mach-at91/board-carmeva.c | 6 ++++--
arch/arm/mach-at91/board-cpu9krea.c | 7 ++++++-
arch/arm/mach-at91/board-cpuat91.c | 4 ++++
arch/arm/mach-at91/board-csb337.c | 4 +++-
arch/arm/mach-at91/board-csb637.c | 1 +
arch/arm/mach-at91/board-eb9200.c | 8 ++++++--
arch/arm/mach-at91/board-ecbat91.c | 4 ++++
arch/arm/mach-at91/board-eco920.c | 4 ++++
arch/arm/mach-at91/board-flexibity.c | 4 +++-
arch/arm/mach-at91/board-foxg20.c | 6 +++++-
arch/arm/mach-at91/board-gsia18s.c | 4 +++-
arch/arm/mach-at91/board-kafa.c | 1 +
arch/arm/mach-at91/board-kb9202.c | 5 ++++-
arch/arm/mach-at91/board-neocore926.c | 4 +++-
arch/arm/mach-at91/board-pcontrol-g20.c | 1 +
arch/arm/mach-at91/board-picotux200.c | 2 ++
arch/arm/mach-at91/board-qil-a9260.c | 11 ++++++-----
arch/arm/mach-at91/board-rm9200dk.c | 10 +++++++---
arch/arm/mach-at91/board-rm9200ek.c | 2 ++
arch/arm/mach-at91/board-sam9-l9260.c | 7 ++++---
arch/arm/mach-at91/board-sam9260ek.c | 11 ++++++-----
arch/arm/mach-at91/board-sam9261ek.c | 8 ++++++--
arch/arm/mach-at91/board-sam9263ek.c | 7 ++++---
arch/arm/mach-at91/board-sam9g20ek.c | 8 +++++++-
arch/arm/mach-at91/board-sam9m10g45ek.c | 3 +++
arch/arm/mach-at91/board-sam9rlek.c | 7 ++++---
arch/arm/mach-at91/board-snapper9260.c | 5 +++++
arch/arm/mach-at91/board-stamp9g20.c | 11 +++++++++--
arch/arm/mach-at91/board-usb-a926x.c | 5 +++--
arch/arm/mach-at91/board-yl-9200.c | 6 ++++--
34 files changed, 141 insertions(+), 50 deletions(-)
diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
index 5aa5885..17d9163 100644
--- a/arch/arm/mach-at91/board-1arm.c
+++ b/arch/arm/mach-at91/board-1arm.c
@@ -70,6 +70,7 @@ static struct at91_eth_data __initdata onearm_eth_data = {
static struct at91_usbh_data __initdata onearm_usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata onearm_udc_data = {
diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c
index b0c796d..c489c27 100644
--- a/arch/arm/mach-at91/board-afeb-9260v1.c
+++ b/arch/arm/mach-at91/board-afeb-9260v1.c
@@ -75,6 +75,7 @@ static void __init afeb9260_init_early(void)
*/
static struct at91_usbh_data __initdata afeb9260_usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
/*
@@ -82,7 +83,7 @@ static struct at91_usbh_data __initdata afeb9260_usbh_data = {
*/
static struct at91_udc_data __initdata afeb9260_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
@@ -143,6 +144,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = {
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
.bus_width_16 = 0,
+ .det_pin = -1,
};
@@ -154,6 +156,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = {
.wp_pin = AT91_PIN_PC4,
.slot_b = 1,
.wire4 = 1,
+ .vcc_pin = -1,
};
@@ -174,6 +177,8 @@ static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
static struct at91_cf_data afeb9260_cf_data = {
.chipselect = 4,
.irq_pin = AT91_PIN_PA6,
+ .det_pin = -1,
+ .vcc_pin = -1,
.rst_pin = AT91_PIN_PA7,
.flags = AT91_CF_TRUE_IDE,
};
diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c
index d1abd58..ed3d87d 100644
--- a/arch/arm/mach-at91/board-cam60.c
+++ b/arch/arm/mach-at91/board-cam60.c
@@ -62,6 +62,7 @@ static void __init cam60_init_early(void)
*/
static struct at91_usbh_data __initdata cam60_usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
@@ -141,7 +142,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata cam60_nand_data = {
.ale = 21,
.cle = 22,
- // .det_pin = ... not there
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PA9,
.enable_pin = AT91_PIN_PA7,
.partition_info = nand_partitions,
diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c
index 679b0b7..da392f3 100644
--- a/arch/arm/mach-at91/board-cap9adk.c
+++ b/arch/arm/mach-at91/board-cap9adk.c
@@ -70,6 +70,7 @@ static void __init cap9adk_init_early(void)
*/
static struct at91_usbh_data __initdata cap9adk_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -144,9 +145,9 @@ static struct spi_board_info cap9adk_spi_devices[] = {
*/
static struct at91_mmc_data __initdata cap9adk_mmc_data = {
.wire4 = 1,
-// .det_pin = ... not connected
-// .wp_pin = ... not connected
-// .vcc_pin = ... not connected
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
@@ -154,6 +155,7 @@ static struct at91_mmc_data __initdata cap9adk_mmc_data = {
* MACB Ethernet device
*/
static struct at91_eth_data __initdata cap9adk_macb_data = {
+ .phy_irq_pin = -1,
.is_rmii = 1,
};
@@ -178,8 +180,8 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata cap9adk_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
-// .rdy_pin = ... not connected
+ .det_pin = -1,
+ .rdy_pin = -1,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
};
@@ -356,7 +358,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
* AC97
*/
static struct ac97c_platform_data cap9adk_ac97_data = {
-// .reset_pin = ... not connected
+ .reset_pin = -1,
};
diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c
index c578c5d..40be90a 100644
--- a/arch/arm/mach-at91/board-carmeva.c
+++ b/arch/arm/mach-at91/board-carmeva.c
@@ -64,6 +64,7 @@ static struct at91_eth_data __initdata carmeva_eth_data = {
static struct at91_usbh_data __initdata carmeva_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata carmeva_udc_data = {
@@ -75,8 +76,8 @@ static struct at91_udc_data __initdata carmeva_udc_data = {
// static struct at91_cf_data __initdata carmeva_cf_data = {
// .det_pin = AT91_PIN_PB0,
// .rst_pin = AT91_PIN_PC5,
- // .irq_pin = ... not connected
- // .vcc_pin = ... always powered
+ // .irq_pin = -1,
+ // .vcc_pin = -1,
// };
static struct at91_mmc_data __initdata carmeva_mmc_data = {
@@ -84,6 +85,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PB10,
.wp_pin = AT91_PIN_PC14,
+ .vcc_pin = -1,
};
static struct spi_board_info carmeva_spi_devices[] = {
diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c
index f4da8a1..a8cdccc 100644
--- a/arch/arm/mach-at91/board-cpu9krea.c
+++ b/arch/arm/mach-at91/board-cpu9krea.c
@@ -86,6 +86,7 @@ static void __init cpu9krea_init_early(void)
*/
static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -93,13 +94,14 @@ static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
*/
static struct at91_udc_data __initdata cpu9krea_udc_data = {
.vbus_pin = AT91_PIN_PC8,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
/*
* MACB Ethernet device
*/
static struct at91_eth_data __initdata cpu9krea_macb_data = {
+ .phy_irq_pin = -1,
.is_rmii = 1,
};
@@ -112,6 +114,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = {
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.bus_width_16 = 0,
+ .det_pin = -1,
};
#ifdef CONFIG_MACH_CPU9260
@@ -337,6 +340,8 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.det_pin = AT91_PIN_PA29,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
static void __init cpu9krea_board_init(void)
diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c
index 2d919f5..02af1cf 100644
--- a/arch/arm/mach-at91/board-cpuat91.c
+++ b/arch/arm/mach-at91/board-cpuat91.c
@@ -83,11 +83,13 @@ static void __init cpuat91_init_early(void)
}
static struct at91_eth_data __initdata cpuat91_eth_data = {
+ .phy_irq_pin = -1,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata cpuat91_usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata cpuat91_udc_data = {
@@ -98,6 +100,8 @@ static struct at91_udc_data __initdata cpuat91_udc_data = {
static struct at91_mmc_data __initdata cpuat91_mmc_data = {
.det_pin = AT91_PIN_PC2,
.wire4 = 1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
static struct physmap_flash_data cpuat91_flash_data = {
diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c
index 17654d5..c16f0f7 100644
--- a/arch/arm/mach-at91/board-csb337.c
+++ b/arch/arm/mach-at91/board-csb337.c
@@ -65,11 +65,12 @@ static struct at91_eth_data __initdata csb337_eth_data = {
static struct at91_usbh_data __initdata csb337_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata csb337_udc_data = {
- // this has no VBUS sensing pin
.pullup_pin = AT91_PIN_PA24,
+ .vbus_pin = -1,
};
static struct i2c_board_info __initdata csb337_i2c_devices[] = {
@@ -98,6 +99,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PD6,
+ .vcc_pin = -1,
};
static struct spi_board_info csb337_spi_devices[] = {
diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c
index 72b5567..0e2d219 100644
--- a/arch/arm/mach-at91/board-csb637.c
+++ b/arch/arm/mach-at91/board-csb637.c
@@ -59,6 +59,7 @@ static struct at91_eth_data __initdata csb637_eth_data = {
static struct at91_usbh_data __initdata csb637_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata csb637_udc_data = {
diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c
index 01170a2..b920f46 100644
--- a/arch/arm/mach-at91/board-eb9200.c
+++ b/arch/arm/mach-at91/board-eb9200.c
@@ -67,6 +67,7 @@ static struct at91_eth_data __initdata eb9200_eth_data = {
static struct at91_usbh_data __initdata eb9200_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata eb9200_udc_data = {
@@ -75,15 +76,18 @@ static struct at91_udc_data __initdata eb9200_udc_data = {
};
static struct at91_cf_data __initdata eb9200_cf_data = {
+ .irq_pin = -1,
.det_pin = AT91_PIN_PB0,
+ .vcc_pin = -1,
.rst_pin = AT91_PIN_PC5,
- // .irq_pin = ... not connected
- // .vcc_pin = ... always powered
};
static struct at91_mmc_data __initdata eb9200_mmc_data = {
.slot_b = 0,
.wire4 = 1,
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
static struct i2c_board_info __initdata eb9200_i2c_devices[] = {
diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c
index 7c0313c..b2ae86c 100644
--- a/arch/arm/mach-at91/board-ecbat91.c
+++ b/arch/arm/mach-at91/board-ecbat91.c
@@ -71,11 +71,15 @@ static struct at91_eth_data __initdata ecb_at91eth_data = {
static struct at91_usbh_data __initdata ecb_at91usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
static struct at91_mmc_data __initdata ecb_at91mmc_data = {
.slot_b = 0,
.wire4 = 1,
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c
index 8252c72..ca1a7d0 100644
--- a/arch/arm/mach-at91/board-eco920.c
+++ b/arch/arm/mach-at91/board-eco920.c
@@ -54,6 +54,7 @@ static struct at91_eth_data __initdata eco920_eth_data = {
static struct at91_usbh_data __initdata eco920_usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata eco920_udc_data = {
@@ -64,6 +65,9 @@ static struct at91_udc_data __initdata eco920_udc_data = {
static struct at91_mmc_data __initdata eco920_mmc_data = {
.slot_b = 0,
.wire4 = 0,
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
static struct physmap_flash_data eco920_flash_data = {
diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c
index 4c3f65d..8605d49 100644
--- a/arch/arm/mach-at91/board-flexibity.c
+++ b/arch/arm/mach-at91/board-flexibity.c
@@ -52,12 +52,13 @@ static void __init flexibity_init_early(void)
/* USB Host port */
static struct at91_usbh_data __initdata flexibity_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/* USB Device port */
static struct at91_udc_data __initdata flexibity_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
/* SPI devices */
@@ -76,6 +77,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PC9,
.wp_pin = AT91_PIN_PC4,
+ .vcc_pin = -1,
};
/* LEDs */
diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
index f27d1a7..7a2e505 100644
--- a/arch/arm/mach-at91/board-foxg20.c
+++ b/arch/arm/mach-at91/board-foxg20.c
@@ -106,6 +106,7 @@ static void __init foxg20_init_early(void)
*/
static struct at91_usbh_data __initdata foxg20_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -113,7 +114,7 @@ static struct at91_usbh_data __initdata foxg20_usbh_data = {
*/
static struct at91_udc_data __initdata foxg20_udc_data = {
.vbus_pin = AT91_PIN_PC6,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
@@ -147,6 +148,9 @@ static struct at91_eth_data __initdata foxg20_macb_data = {
static struct at91_mmc_data __initdata foxg20_mmc_data = {
.slot_b = 1,
.wire4 = 1,
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
diff --git a/arch/arm/mach-at91/board-gsia18s.c b/arch/arm/mach-at91/board-gsia18s.c
index 2e95949..1c36ea2 100644
--- a/arch/arm/mach-at91/board-gsia18s.c
+++ b/arch/arm/mach-at91/board-gsia18s.c
@@ -80,6 +80,7 @@ static void __init gsia18s_init_early(void)
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -87,7 +88,7 @@ static struct at91_usbh_data __initdata usbh_data = {
*/
static struct at91_udc_data __initdata udc_data = {
.vbus_pin = AT91_PIN_PA22,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
/*
@@ -530,6 +531,7 @@ static struct i2c_board_info __initdata gsia18s_i2c_devices[] = {
static struct at91_cf_data __initdata gsia18s_cf1_data = {
.irq_pin = AT91_PIN_PA27,
.det_pin = AT91_PIN_PB30,
+ .vcc_pin = -1,
.rst_pin = AT91_PIN_PB31,
.chipselect = 5,
.flags = AT91_CF_TRUE_IDE,
diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c
index 4a17089..8d64e90 100644
--- a/arch/arm/mach-at91/board-kafa.c
+++ b/arch/arm/mach-at91/board-kafa.c
@@ -68,6 +68,7 @@ static struct at91_eth_data __initdata kafa_eth_data = {
static struct at91_usbh_data __initdata kafa_usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata kafa_udc_data = {
diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c
index 9dc8d49..be5ed23 100644
--- a/arch/arm/mach-at91/board-kb9202.c
+++ b/arch/arm/mach-at91/board-kb9202.c
@@ -76,6 +76,7 @@ static struct at91_eth_data __initdata kb9202_eth_data = {
static struct at91_usbh_data __initdata kb9202_usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata kb9202_udc_data = {
@@ -87,6 +88,8 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = {
.det_pin = AT91_PIN_PB2,
.slot_b = 0,
.wire4 = 1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
static struct mtd_partition __initdata kb9202_nand_partition[] = {
@@ -106,7 +109,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata kb9202_nand_data = {
.ale = 22,
.cle = 21,
- // .det_pin = ... not there
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PC29,
.enable_pin = AT91_PIN_PC28,
.partition_info = nand_partitions,
diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c
index 9bc6ab3..2f6cc36 100644
--- a/arch/arm/mach-at91/board-neocore926.c
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -79,7 +79,7 @@ static struct at91_usbh_data __initdata neocore926_usbh_data = {
*/
static struct at91_udc_data __initdata neocore926_udc_data = {
.vbus_pin = AT91_PIN_PA25,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
@@ -149,6 +149,7 @@ static struct at91_mmc_data __initdata neocore926_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PE18,
.wp_pin = AT91_PIN_PE19,
+ .vcc_pin = -1,
};
@@ -195,6 +196,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = {
.rdy_pin_active_low = 1,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
+ .det_pin = -1,
};
static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c
index 49e3f69..f817cb8 100644
--- a/arch/arm/mach-at91/board-pcontrol-g20.c
+++ b/arch/arm/mach-at91/board-pcontrol-g20.c
@@ -107,6 +107,7 @@ static void __init add_device_pcontrol(void)
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c
index b7b8390..88b2a84 100644
--- a/arch/arm/mach-at91/board-picotux200.c
+++ b/arch/arm/mach-at91/board-picotux200.c
@@ -67,6 +67,7 @@ static struct at91_eth_data __initdata picotux200_eth_data = {
static struct at91_usbh_data __initdata picotux200_usbh_data = {
.ports = 1,
+ .vbus_pin = {-1, -1},
};
static struct at91_mmc_data __initdata picotux200_mmc_data = {
@@ -74,6 +75,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
+ .vcc_pin = -1,
};
#define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0
diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c
index 81f9110..1cdde5c 100644
--- a/arch/arm/mach-at91/board-qil-a9260.c
+++ b/arch/arm/mach-at91/board-qil-a9260.c
@@ -77,6 +77,7 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -84,7 +85,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
/*
@@ -139,7 +140,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
@@ -177,9 +178,9 @@ static void __init ek_add_device_nand(void)
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 0,
.wire4 = 1,
-// .det_pin = ... not connected
-// .wp_pin = ... not connected
-// .vcc_pin = ... not connected
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
/*
diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c
index 6f08faa..5198d87 100644
--- a/arch/arm/mach-at91/board-rm9200dk.c
+++ b/arch/arm/mach-at91/board-rm9200dk.c
@@ -72,6 +72,7 @@ static struct at91_eth_data __initdata dk_eth_data = {
static struct at91_usbh_data __initdata dk_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata dk_udc_data = {
@@ -80,16 +81,19 @@ static struct at91_udc_data __initdata dk_udc_data = {
};
static struct at91_cf_data __initdata dk_cf_data = {
+ .irq_pin = -1,
.det_pin = AT91_PIN_PB0,
+ .vcc_pin = -1,
.rst_pin = AT91_PIN_PC5,
- // .irq_pin = ... not connected
- // .vcc_pin = ... always powered
};
#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
static struct at91_mmc_data __initdata dk_mmc_data = {
.slot_b = 0,
.wire4 = 1,
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
#endif
@@ -149,7 +153,7 @@ static struct atmel_nand_data __initdata dk_nand_data = {
.cle = 21,
.det_pin = AT91_PIN_PB1,
.rdy_pin = AT91_PIN_PC2,
- // .enable_pin = ... not there
+ .enable_pin = -1,
.partition_info = nand_partitions,
};
diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c
index 85bcccd..4fb14c0 100644
--- a/arch/arm/mach-at91/board-rm9200ek.c
+++ b/arch/arm/mach-at91/board-rm9200ek.c
@@ -72,6 +72,7 @@ static struct at91_eth_data __initdata ek_eth_data = {
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata ek_udc_data = {
@@ -85,6 +86,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.wp_pin = AT91_PIN_PA17,
+ .vcc_pin = -1,
};
#endif
diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c
index 4d3a02f..6069d0f 100644
--- a/arch/arm/mach-at91/board-sam9-l9260.c
+++ b/arch/arm/mach-at91/board-sam9-l9260.c
@@ -72,6 +72,7 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -79,7 +80,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
@@ -140,7 +141,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
@@ -181,7 +182,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PC8,
.wp_pin = AT91_PIN_PC4,
-// .vcc_pin = ... not connected
+ .vcc_pin = -1,
};
static void __init ek_board_init(void)
diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c
index 8a50c3e..9681120 100644
--- a/arch/arm/mach-at91/board-sam9260ek.c
+++ b/arch/arm/mach-at91/board-sam9260ek.c
@@ -75,6 +75,7 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -82,7 +83,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
@@ -182,7 +183,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
@@ -228,9 +229,9 @@ static void __init ek_add_device_nand(void)
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 1,
.wire4 = 1,
-// .det_pin = ... not connected
-// .wp_pin = ... not connected
-// .vcc_pin = ... not connected
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 5096a0e..8ce4753 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -151,6 +151,7 @@ static void __init ek_add_device_dm9000(void) {}
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
@@ -159,7 +160,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PB29,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
@@ -188,7 +189,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 22,
.cle = 21,
-// .det_pin = ... not connected
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PC15,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
@@ -350,6 +351,9 @@ static struct spi_board_info ek_spi_devices[] = {
*/
static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
#endif /* CONFIG_SPI_ATMEL_* */
diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c
index ea8f185..4855a9a 100644
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -81,7 +81,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PA25,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
@@ -151,7 +151,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PE18,
.wp_pin = AT91_PIN_PE19,
-// .vcc_pin = ... not connected
+ .vcc_pin = -1,
};
@@ -189,7 +189,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
@@ -358,6 +358,7 @@ static void __init ek_add_device_buttons(void) {}
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
+ .reset_pin = -1,
};
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index 817f59d..90fb231 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -86,6 +86,7 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -93,7 +94,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
@@ -170,6 +171,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
+ .det_pin = -1,
};
static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -215,6 +217,7 @@ static struct mci_platform_data __initdata ek_mmc_data = {
.slot[1] = {
.bus_width = 4,
.detect_pin = AT91_PIN_PC9,
+ .wp_pin = -1;
},
};
@@ -223,6 +226,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 1, /* Only one slot so use slot B */
.wire4 = 1,
.det_pin = AT91_PIN_PC9,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
#endif
@@ -232,6 +237,7 @@ static void __init ek_add_device_mmc(void)
if (ek_have_2mmc()) {
ek_mmc_data.slot[0].bus_width = 4;
ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
+ ek_mmc_data.slot[0].wp_pin = -1;
}
at91_add_device_mci(0, &ek_mmc_data);
#else
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index ad234cc..a5dad78 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -100,6 +100,7 @@ static struct mci_platform_data __initdata mci0_data = {
.slot[0] = {
.bus_width = 4,
.detect_pin = AT91_PIN_PD10,
+ .wp_pin = -1;
},
};
@@ -150,6 +151,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
.rdy_pin = AT91_PIN_PC8,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
+ .det_pin = -1,
};
static struct sam9_smc_config __initdata ek_nand_smc_config = {
@@ -335,6 +337,7 @@ static void __init ek_add_device_buttons(void) {}
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
+ .reset_pin = -1,
};
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
index 4f14b54..903505a 100644
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ b/arch/arm/mach-at91/board-sam9rlek.c
@@ -67,8 +67,8 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PA15,
-// .wp_pin = ... not connected
-// .vcc_pin = ... not connected
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
@@ -97,7 +97,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PD17,
.enable_pin = AT91_PIN_PB6,
.partition_info = nand_partitions,
@@ -209,6 +209,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
* reset_pin is not connected: NRST
*/
static struct ac97c_platform_data ek_ac97_data = {
+ .reset_pin = -1,
};
diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c
index c73d25e..837591b 100644
--- a/arch/arm/mach-at91/board-snapper9260.c
+++ b/arch/arm/mach-at91/board-snapper9260.c
@@ -57,15 +57,18 @@ static void __init snapper9260_init_early(void)
static struct at91_usbh_data __initdata snapper9260_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
static struct at91_udc_data __initdata snapper9260_udc_data = {
.vbus_pin = SNAPPER9260_IO_EXP_GPIO(5),
.vbus_active_low = 1,
.vbus_polled = 1,
+ .pullup_pin = -1,
};
static struct at91_eth_data snapper9260_macb_data = {
+ .phy_irq_pin = -1,
.is_rmii = 1,
};
@@ -110,6 +113,8 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = {
.rdy_pin = AT91_PIN_PC13,
.partition_info = snapper9260_nand_partition_info,
.bus_width_16 = 0,
+ .enable_pin = -1,
+ .det_pin = -1,
};
static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c
index 936e5fd..6162976 100644
--- a/arch/arm/mach-at91/board-stamp9g20.c
+++ b/arch/arm/mach-at91/board-stamp9g20.c
@@ -85,6 +85,7 @@ static struct atmel_nand_data __initdata nand_data = {
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.bus_width_16 = 0,
+ .det_pin = -1,
};
static struct sam9_smc_config __initdata nand_smc_config = {
@@ -122,12 +123,17 @@ static void __init add_device_nand(void)
static struct mci_platform_data __initdata mmc_data = {
.slot[0] = {
.bus_width = 4,
+ .detect_pin = -1;
+ .wp_pin = -1;
},
};
#else
static struct at91_mmc_data __initdata mmc_data = {
.slot_b = 0,
.wire4 = 1,
+ .det_pin = -1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
#endif
@@ -137,6 +143,7 @@ static struct at91_mmc_data __initdata mmc_data = {
*/
static struct at91_usbh_data __initdata usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
@@ -145,12 +152,12 @@ static struct at91_usbh_data __initdata usbh_data = {
*/
static struct at91_udc_data __initdata portuxg20_udc_data = {
.vbus_pin = AT91_PIN_PC7,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
.vbus_pin = AT91_PIN_PA22,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c
index 260260b..ffa5aab 100644
--- a/arch/arm/mach-at91/board-usb-a926x.c
+++ b/arch/arm/mach-at91/board-usb-a926x.c
@@ -66,6 +66,7 @@ static void __init ek_init_early(void)
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
+ .vbus_pin = {-1, -1},
};
/*
@@ -73,7 +74,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PB11,
- .pullup_pin = 0, /* pull-up driven by UDC */
+ .pullup_pin = -1, /* pull-up driven by UDC */
};
static void __init ek_add_device_udc(void)
@@ -199,7 +200,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
-// .det_pin = ... not connected
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c
index 95edcbd..5108bd7 100644
--- a/arch/arm/mach-at91/board-yl-9200.c
+++ b/arch/arm/mach-at91/board-yl-9200.c
@@ -120,6 +120,7 @@ static struct at91_eth_data __initdata yl9200_eth_data = {
*/
static struct at91_usbh_data __initdata yl9200_usbh_data = {
.ports = 1, /* PQFP version of AT91RM9200 */
+ .vbus_pin = {-1, -1},
};
/*
@@ -137,8 +138,9 @@ static struct at91_udc_data __initdata yl9200_udc_data = {
*/
static struct at91_mmc_data __initdata yl9200_mmc_data = {
.det_pin = AT91_PIN_PB9,
- // .wp_pin = ... not connected
.wire4 = 1,
+ .wp_pin = -1,
+ .vcc_pin = -1,
};
/*
@@ -181,7 +183,7 @@ static struct mtd_partition * __init nand_partitions(int size, int *num_partitio
static struct atmel_nand_data __initdata yl9200_nand_data = {
.ale = 6,
.cle = 7,
- // .det_pin = ... not connected
+ .det_pin = -1,
.rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */
.enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */
.partition_info = nand_partitions,
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 03/11] at91/soc: use gpio_is_valid to check the gpio
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 02/11] at91/boards: use -1 for invalid gpio Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 12:51 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 04/11] at91/pata: " Jean-Christophe PLAGNIOL-VILLARD
` (7 subsequent siblings)
9 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 12:51 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/mach-at91/at91cap9_devices.c | 20 ++++++++++----------
arch/arm/mach-at91/at91rm9200_devices.c | 22 +++++++++++-----------
arch/arm/mach-at91/at91sam9260_devices.c | 26 +++++++++++++-------------
arch/arm/mach-at91/at91sam9261_devices.c | 14 +++++++-------
arch/arm/mach-at91/at91sam9263_devices.c | 26 +++++++++++++-------------
arch/arm/mach-at91/at91sam9g45_devices.c | 20 ++++++++++----------
arch/arm/mach-at91/at91sam9rl_devices.c | 16 ++++++++--------
7 files changed, 72 insertions(+), 72 deletions(-)
diff --git a/arch/arm/mach-at91/at91cap9_devices.c b/arch/arm/mach-at91/at91cap9_devices.c
index dba0d8d..2838f8b 100644
--- a/arch/arm/mach-at91/at91cap9_devices.c
+++ b/arch/arm/mach-at91/at91cap9_devices.c
@@ -76,7 +76,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
@@ -173,7 +173,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
- if (data && data->vbus_pin > 0) {
+ if (data && gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -226,7 +226,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
@@ -326,13 +326,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
if (mmc_id == 0) { /* MCI0 */
@@ -419,15 +419,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
@@ -801,7 +801,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
at91_set_A_periph(AT91_PIN_PA9, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;
diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c
index 7227755..ff90b63 100644
--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -106,11 +106,11 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
if (!data)
return;
- if (data->vbus_pin) {
+ if (gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
- if (data->pullup_pin)
+ if (gpio_is_valid(data->pullup_pin))
at91_set_gpio_output(data->pullup_pin, 0);
udc_data = *data;
@@ -159,7 +159,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
@@ -252,7 +252,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
);
/* input/irq */
- if (data->irq_pin) {
+ if (gpio_is_valid(data->irq_pin)) {
at91_set_gpio_input(data->irq_pin, 1);
at91_set_deglitch(data->irq_pin, 1);
}
@@ -260,7 +260,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
at91_set_deglitch(data->det_pin, 1);
/* outputs, initially off */
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
at91_set_gpio_output(data->rst_pin, 0);
@@ -320,13 +320,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
@@ -411,15 +411,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 39f81f4..b981a5c 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -107,7 +107,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
if (!data)
return;
- if (data->vbus_pin) {
+ if (gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
@@ -160,7 +160,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
@@ -235,13 +235,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
@@ -322,11 +322,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
for (i = 0; i < ATMEL_MCI_MAX_NR_SLOTS; i++) {
if (data->slot[i].bus_width) {
/* input/irq */
- if (data->slot[i].detect_pin) {
+ if (gpio_is_valid(data->slot[i].detect_pin)) {
at91_set_gpio_input(data->slot[i].detect_pin, 1);
at91_set_deglitch(data->slot[i].detect_pin, 1);
}
- if (data->slot[i].wp_pin)
+ if (gpio_is_valid(data->slot[i].wp_pin))
at91_set_gpio_input(data->slot[i].wp_pin, 1);
switch (i) {
@@ -418,15 +418,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
@@ -1274,17 +1274,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
at91_sys_write(AT91_MATRIX_EBICSA, csa);
- if (data->rst_pin) {
+ if (gpio_is_valid(data->rst_pin)) {
at91_set_multi_drive(data->rst_pin, 0);
at91_set_gpio_output(data->rst_pin, 1);
}
- if (data->irq_pin) {
+ if (gpio_is_valid(data->irq_pin)) {
at91_set_gpio_input(data->irq_pin, 0);
at91_set_deglitch(data->irq_pin, 1);
}
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 0);
at91_set_deglitch(data->det_pin, 1);
}
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 0f91792..0dd3960 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -110,7 +110,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
if (!data)
return;
- if (data->vbus_pin) {
+ if (gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
@@ -163,13 +163,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
@@ -232,15 +232,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index a050f41..077d853 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -70,7 +70,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
@@ -117,7 +117,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
if (!data)
return;
- if (data->vbus_pin) {
+ if (gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
@@ -170,7 +170,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
@@ -270,13 +270,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
if (mmc_id == 0) { /* MCI0 */
@@ -424,17 +424,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
}
at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->irq_pin) {
+ if (gpio_is_valid(data->irq_pin)) {
at91_set_gpio_input(data->irq_pin, 1);
at91_set_deglitch(data->irq_pin, 1);
}
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
/* initially off */
at91_set_gpio_output(data->vcc_pin, 0);
@@ -494,15 +494,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
@@ -743,7 +743,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
at91_set_A_periph(AT91_PIN_PB3, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 600bffb..3a0daa3 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -120,7 +120,7 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
@@ -175,7 +175,7 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
- if (data->vbus_pin[i])
+ if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i], 0);
}
@@ -257,7 +257,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
- if (data && data->vbus_pin > 0) {
+ if (data && gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -310,7 +310,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
if (!data)
return;
- if (data->phy_irq_pin) {
+ if (gpio_is_valid(data->phy_irq_pin)) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
@@ -443,11 +443,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
/* input/irq */
- if (data->slot[0].detect_pin) {
+ if (gpio_is_valid(data->slot[0].detect_pin)) {
at91_set_gpio_input(data->slot[0].detect_pin, 1);
at91_set_deglitch(data->slot[0].detect_pin, 1);
}
- if (data->slot[0].wp_pin)
+ if (gpio_is_valid(data->slot[0].wp_pin))
at91_set_gpio_input(data->slot[0].wp_pin, 1);
if (mmc_id == 0) { /* MCI0 */
@@ -550,15 +550,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
nand_data = *data;
@@ -853,7 +853,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
at91_set_A_periph(AT91_PIN_PD6, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index aacb19d..56cb73d 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -147,7 +147,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
- if (data && data->vbus_pin > 0) {
+ if (data && gpio_is_valid(data->vbus_pin)) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -201,13 +201,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
return;
/* input/irq */
- if (data->det_pin) {
+ if (gpio_is_valid(data->det_pin)) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
- if (data->wp_pin)
+ if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
- if (data->vcc_pin)
+ if (gpio_is_valid(data->vcc_pin))
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
@@ -275,15 +275,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
- if (data->enable_pin)
+ if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
- if (data->rdy_pin)
+ if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
- if (data->det_pin)
+ if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PB4, 0); /* NANDOE */
@@ -483,7 +483,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
at91_set_A_periph(AT91_PIN_PD4, 0); /* AC97RX */
/* reset */
- if (data->reset_pin)
+ if (gpio_is_valid(data->reset_pin))
at91_set_gpio_output(data->reset_pin, 0);
ac97_data = *data;
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 04/11] at91/pata: use gpio_is_valid to check the gpio
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 02/11] at91/boards: use -1 for invalid gpio Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 03/11] at91/soc: use gpio_is_valid to check the gpio Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 12:51 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 05/11] at91/ide: " Jean-Christophe PLAGNIOL-VILLARD
` (6 subsequent siblings)
9 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 12:51 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: linux-ide at vger.kernel.org
---
drivers/ata/pata_at91.c | 6 +++---
1 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c
index 960c725..3915353 100644
--- a/drivers/ata/pata_at91.c
+++ b/drivers/ata/pata_at91.c
@@ -360,7 +360,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
ap->flags |= ATA_FLAG_SLAVE_POSS;
ap->pio_mask = ATA_PIO4;
- if (!irq) {
+ if (!gpio_is_valid(irq)) {
ap->flags |= ATA_FLAG_PIO_POLLING;
ata_port_desc(ap, "no IRQ, using PIO polling");
}
@@ -414,8 +414,8 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
host->private_data = info;
- return ata_host_activate(host, irq ? gpio_to_irq(irq) : 0,
- irq ? ata_sff_interrupt : NULL,
+ return ata_host_activate(host, gpio_is_valid(irq) ? gpio_to_irq(irq) : 0,
+ gpio_is_valid(irq) ? ata_sff_interrupt : NULL,
irq_flags, &pata_at91_sht);
err_put:
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 05/11] at91/ide: use gpio_is_valid to check the gpio
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
` (2 preceding siblings ...)
2011-09-19 12:51 ` [PATCH 04/11] at91/pata: " Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 12:51 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 06/11] at91/mmc: " Jean-Christophe PLAGNIOL-VILLARD
` (5 subsequent siblings)
9 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 12:51 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: linux-ide at vger.kernel.org
---
Hi,
I'd like to apply this patch via AT91 with the whole gpio patch series
Best Regards,
J.
drivers/ide/at91_ide.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/drivers/ide/at91_ide.c b/drivers/ide/at91_ide.c
index 000a78e..ba2eda3 100644
--- a/drivers/ide/at91_ide.c
+++ b/drivers/ide/at91_ide.c
@@ -314,7 +314,7 @@ static int __init at91_ide_probe(struct platform_device *pdev)
apply_timings(board->chipselect, 0, ide_timing_find_mode(XFER_PIO_0), 0);
/* with GPIO interrupt we have to do quirks in handler */
- if (board->irq_pin >= PIN_BASE)
+ if (gpio_is_valid(board->irq_pin))
host->irq_handler = at91_irq_handler;
host->ports[0]->select_data = board->chipselect;
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 06/11] at91/mmc: use gpio_is_valid to check the gpio
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
` (3 preceding siblings ...)
2011-09-19 12:51 ` [PATCH 05/11] at91/ide: " Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 14:03 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 07/11] at92/nand: " Jean-Christophe PLAGNIOL-VILLARD
` (4 subsequent siblings)
9 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 14:03 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: linux-mmc at vger.kernel.org
---
Hi,
I'd like to apply this patch via AT91 with the whole gpio patch series
Best Regards,
J.
drivers/mmc/host/at91_mci.c | 30 +++++++++++++++---------------
1 files changed, 15 insertions(+), 15 deletions(-)
diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c
index a4aa3af..7504b22 100644
--- a/drivers/mmc/host/at91_mci.c
+++ b/drivers/mmc/host/at91_mci.c
@@ -741,7 +741,7 @@ static void at91_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
at91_mci_write(host, AT91_MCI_MR, (at91_mci_read(host, AT91_MCI_MR) & ~AT91_MCI_CLKDIV) | clkdiv);
/* maybe switch power to the card */
- if (host->board->vcc_pin) {
+ if (gpio_is_valid(host->board->vcc_pin)) {
switch (ios->power_mode) {
case MMC_POWER_OFF:
gpio_set_value(host->board->vcc_pin, 0);
@@ -893,7 +893,7 @@ static int at91_mci_get_ro(struct mmc_host *mmc)
{
struct at91mci_host *host = mmc_priv(mmc);
- if (host->board->wp_pin)
+ if (gpio_is_valid(host->board->wp_pin))
return !!gpio_get_value(host->board->wp_pin);
/*
* Board doesn't support read only detection; let the mmc core
@@ -987,21 +987,21 @@ static int __init at91_mci_probe(struct platform_device *pdev)
* Reserve GPIOs ... board init code makes sure these pins are set
* up as GPIOs with the right direction (input, except for vcc)
*/
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
ret = gpio_request(host->board->det_pin, "mmc_detect");
if (ret < 0) {
dev_dbg(&pdev->dev, "couldn't claim card detect pin\n");
goto fail4b;
}
}
- if (host->board->wp_pin) {
+ if (gpio_is_valid(host->board->wp_pin)) {
ret = gpio_request(host->board->wp_pin, "mmc_wp");
if (ret < 0) {
dev_dbg(&pdev->dev, "couldn't claim wp sense pin\n");
goto fail4;
}
}
- if (host->board->vcc_pin) {
+ if (gpio_is_valid(host->board->vcc_pin)) {
ret = gpio_request(host->board->vcc_pin, "mmc_vcc");
if (ret < 0) {
dev_dbg(&pdev->dev, "couldn't claim vcc switch pin\n");
@@ -1053,7 +1053,7 @@ static int __init at91_mci_probe(struct platform_device *pdev)
/*
* Add host to MMC layer
*/
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
host->present = !gpio_get_value(host->board->det_pin);
}
else
@@ -1064,7 +1064,7 @@ static int __init at91_mci_probe(struct platform_device *pdev)
/*
* monitor card insertion/removal if we can
*/
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
ret = request_irq(gpio_to_irq(host->board->det_pin),
at91_mmc_det_irq, 0, mmc_hostname(mmc), host);
if (ret)
@@ -1083,13 +1083,13 @@ fail0:
fail1:
clk_put(host->mci_clk);
fail2:
- if (host->board->vcc_pin)
+ if (gpio_is_valid(host->board->vcc_pin))
gpio_free(host->board->vcc_pin);
fail3:
- if (host->board->wp_pin)
+ if (gpio_is_valid(host->board->wp_pin))
gpio_free(host->board->wp_pin);
fail4:
- if (host->board->det_pin)
+ if (gpio_is_valid(host->board->det_pin))
gpio_free(host->board->det_pin);
fail4b:
if (host->buffer)
@@ -1121,7 +1121,7 @@ static int __exit at91_mci_remove(struct platform_device *pdev)
dma_free_coherent(&pdev->dev, MCI_BUFSIZE,
host->buffer, host->physical_address);
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
if (device_can_wakeup(&pdev->dev))
free_irq(gpio_to_irq(host->board->det_pin), host);
device_init_wakeup(&pdev->dev, 0);
@@ -1136,9 +1136,9 @@ static int __exit at91_mci_remove(struct platform_device *pdev)
clk_disable(host->mci_clk); /* Disable the peripheral clock */
clk_put(host->mci_clk);
- if (host->board->vcc_pin)
+ if (gpio_is_valid(host->board->vcc_pin))
gpio_free(host->board->vcc_pin);
- if (host->board->wp_pin)
+ if (gpio_is_valid(host->board->wp_pin))
gpio_free(host->board->wp_pin);
iounmap(host->baseaddr);
@@ -1159,7 +1159,7 @@ static int at91_mci_suspend(struct platform_device *pdev, pm_message_t state)
struct at91mci_host *host = mmc_priv(mmc);
int ret = 0;
- if (host->board->det_pin && device_may_wakeup(&pdev->dev))
+ if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev))
enable_irq_wake(host->board->det_pin);
if (mmc)
@@ -1174,7 +1174,7 @@ static int at91_mci_resume(struct platform_device *pdev)
struct at91mci_host *host = mmc_priv(mmc);
int ret = 0;
- if (host->board->det_pin && device_may_wakeup(&pdev->dev))
+ if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev))
disable_irq_wake(host->board->det_pin);
if (mmc)
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 07/11] at92/nand: use gpio_is_valid to check the gpio
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
` (4 preceding siblings ...)
2011-09-19 14:03 ` [PATCH 06/11] at91/mmc: " Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 14:03 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 08/11] at92/udc: " Jean-Christophe PLAGNIOL-VILLARD
` (3 subsequent siblings)
9 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 14:03 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: linux-mtd at lists.infradead.org
---
Hi,
I'd like to apply this patch via AT91 with the whole gpio patch series
Best Regards,
J.
drivers/mtd/nand/atmel_nand.c | 8 ++++----
1 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
index 55da20c..e20ac1f 100644
--- a/drivers/mtd/nand/atmel_nand.c
+++ b/drivers/mtd/nand/atmel_nand.c
@@ -113,7 +113,7 @@ static int cpu_has_dma(void)
*/
static void atmel_nand_enable(struct atmel_nand_host *host)
{
- if (host->board->enable_pin)
+ if (gpio_is_valid(host->board->enable_pin))
gpio_set_value(host->board->enable_pin, 0);
}
@@ -122,7 +122,7 @@ static void atmel_nand_enable(struct atmel_nand_host *host)
*/
static void atmel_nand_disable(struct atmel_nand_host *host)
{
- if (host->board->enable_pin)
+ if (gpio_is_valid(host->board->enable_pin))
gpio_set_value(host->board->enable_pin, 1);
}
@@ -535,7 +535,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
nand_chip->IO_ADDR_W = host->io_base;
nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl;
- if (host->board->rdy_pin)
+ if (gpio_is_valid(host->board->rdy_pin))
nand_chip->dev_ready = atmel_nand_device_ready;
regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);
@@ -573,7 +573,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, host);
atmel_nand_enable(host);
- if (host->board->det_pin) {
+ if (gpio_is_valid(host->board->det_pin)) {
if (gpio_get_value(host->board->det_pin)) {
printk(KERN_INFO "No SmartMedia card inserted.\n");
res = -ENXIO;
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 08/11] at92/udc: use gpio_is_valid to check the gpio
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
` (5 preceding siblings ...)
2011-09-19 14:03 ` [PATCH 07/11] at92/nand: " Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 14:03 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-20 9:52 ` Sebastian Andrzej Siewior
2011-09-19 14:03 ` [PATCH 09/11] at92/ohci: " Jean-Christophe PLAGNIOL-VILLARD
` (2 subsequent siblings)
9 siblings, 1 reply; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 14:03 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: linux-usb at vger.kernel.org
---
Hi,
I'd like to apply this patch via AT91 with the whole gpio patch series
Best Regards,
J.
drivers/usb/gadget/at91_udc.c | 14 +++++++-------
1 files changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c
index ddb118a..205498d 100644
--- a/drivers/usb/gadget/at91_udc.c
+++ b/drivers/usb/gadget/at91_udc.c
@@ -1758,7 +1758,7 @@ static int __init at91udc_probe(struct platform_device *pdev)
/* rm9200 needs manual D+ pullup; off by default */
if (cpu_is_at91rm9200()) {
- if (udc->board.pullup_pin <= 0) {
+ if (gpio_is_valid(udc->board.pullup_pin)) {
DBG("no D+ pullup?\n");
retval = -ENODEV;
goto fail0;
@@ -1825,7 +1825,7 @@ static int __init at91udc_probe(struct platform_device *pdev)
DBG("request irq %d failed\n", udc->udp_irq);
goto fail1;
}
- if (udc->board.vbus_pin > 0) {
+ if (gpio_is_valid(udc->board.vbus_pin)) {
retval = gpio_request(udc->board.vbus_pin, "udc_vbus");
if (retval < 0) {
DBG("request vbus pin failed\n");
@@ -1869,10 +1869,10 @@ static int __init at91udc_probe(struct platform_device *pdev)
INFO("%s version %s\n", driver_name, DRIVER_VERSION);
return 0;
fail4:
- if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled)
+ if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled)
free_irq(udc->board.vbus_pin, udc);
fail3:
- if (udc->board.vbus_pin > 0)
+ if (gpio_is_valid(udc->board.vbus_pin))
gpio_free(udc->board.vbus_pin);
fail2:
free_irq(udc->udp_irq, udc);
@@ -1907,7 +1907,7 @@ static int __exit at91udc_remove(struct platform_device *pdev)
device_init_wakeup(&pdev->dev, 0);
remove_debug_file(udc);
- if (udc->board.vbus_pin > 0) {
+ if (gpio_is_valid(udc->board.vbus_pin)) {
free_irq(udc->board.vbus_pin, udc);
gpio_free(udc->board.vbus_pin);
}
@@ -1951,7 +1951,7 @@ static int at91udc_suspend(struct platform_device *pdev, pm_message_t mesg)
enable_irq_wake(udc->udp_irq);
udc->active_suspend = wake;
- if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled && wake)
+ if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled && wake)
enable_irq_wake(udc->board.vbus_pin);
return 0;
}
@@ -1961,7 +1961,7 @@ static int at91udc_resume(struct platform_device *pdev)
struct at91_udc *udc = platform_get_drvdata(pdev);
unsigned long flags;
- if (udc->board.vbus_pin > 0 && !udc->board.vbus_polled &&
+ if (gpio_is_valid(udc->board.vbus_pin) && !udc->board.vbus_polled &&
udc->active_suspend)
disable_irq_wake(udc->board.vbus_pin);
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 09/11] at92/ohci: use gpio_is_valid to check the gpio
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
` (6 preceding siblings ...)
2011-09-19 14:03 ` [PATCH 08/11] at92/udc: " Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 14:03 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 10/11] at91/gpio: drop PIN_BASE Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 11/11] at91/gpio: fix display of number of irq setuped Jean-Christophe PLAGNIOL-VILLARD
9 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 14:03 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: linux-usb at vger.kernel.org
---
Hi,
I'd like to apply this patch via AT91 with the whole gpio patch series
Best Regards,
J.
drivers/usb/host/ohci-at91.c | 4 ++--
1 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c
index e08cb10..70701f4 100644
--- a/drivers/usb/host/ohci-at91.c
+++ b/drivers/usb/host/ohci-at91.c
@@ -276,7 +276,7 @@ static int ohci_hcd_at91_drv_probe(struct platform_device *pdev)
* active-low power switches.
*/
for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
- if (pdata->vbus_pin[i] <= 0)
+ if (!gpio_is_valid(pdata->vbus_pin[i]))
continue;
gpio_request(pdata->vbus_pin[i], "ohci_vbus");
gpio_direction_output(pdata->vbus_pin[i], 0);
@@ -294,7 +294,7 @@ static int ohci_hcd_at91_drv_remove(struct platform_device *pdev)
if (pdata) {
for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
- if (pdata->vbus_pin[i] <= 0)
+ if (!gpio_is_valid(pdata->vbus_pin[i]))
continue;
gpio_direction_output(pdata->vbus_pin[i], 1);
gpio_free(pdata->vbus_pin[i]);
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 10/11] at91/gpio: drop PIN_BASE
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
` (7 preceding siblings ...)
2011-09-19 14:03 ` [PATCH 09/11] at92/ohci: " Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 14:03 ` Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 11/11] at91/gpio: fix display of number of irq setuped Jean-Christophe PLAGNIOL-VILLARD
9 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 14:03 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
---
arch/arm/mach-at91/gpio.c | 54 ++--
arch/arm/mach-at91/include/mach/gpio.h | 454 ++++++++++++++++----------------
2 files changed, 254 insertions(+), 254 deletions(-)
rewrite arch/arm/mach-at91/include/mach/gpio.h (78%)
diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c
index 04beff1..e709406 100644
--- a/arch/arm/mach-at91/gpio.c
+++ b/arch/arm/mach-at91/gpio.c
@@ -60,18 +60,17 @@ static int at91_gpiolib_direction_input(struct gpio_chip *chip,
}
static struct at91_gpio_chip gpio_chip[] = {
- AT91_GPIO_CHIP("A", 0x00 + PIN_BASE, 32),
- AT91_GPIO_CHIP("B", 0x20 + PIN_BASE, 32),
- AT91_GPIO_CHIP("C", 0x40 + PIN_BASE, 32),
- AT91_GPIO_CHIP("D", 0x60 + PIN_BASE, 32),
- AT91_GPIO_CHIP("E", 0x80 + PIN_BASE, 32),
+ AT91_GPIO_CHIP("A", 0x00, 32),
+ AT91_GPIO_CHIP("B", 0x20, 32),
+ AT91_GPIO_CHIP("C", 0x40, 32),
+ AT91_GPIO_CHIP("D", 0x60, 32),
+ AT91_GPIO_CHIP("E", 0x80, 32),
};
static int gpio_banks;
static inline void __iomem *pin_to_controller(unsigned pin)
{
- pin -= PIN_BASE;
pin /= 32;
if (likely(pin < gpio_banks))
return gpio_chip[pin].regbase;
@@ -81,7 +80,6 @@ static inline void __iomem *pin_to_controller(unsigned pin)
static inline unsigned pin_to_mask(unsigned pin)
{
- pin -= PIN_BASE;
return 1 << (pin % 32);
}
@@ -276,8 +274,9 @@ static u32 backups[MAX_GPIO_BANKS];
static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
{
- unsigned mask = pin_to_mask(d->irq);
- unsigned bank = (d->irq - PIN_BASE) / 32;
+ unsigned pin = irq_to_gpio(d->irq);
+ unsigned mask = pin_to_mask(pin);
+ unsigned bank = pin / 32;
if (unlikely(bank >= MAX_GPIO_BANKS))
return -EINVAL;
@@ -346,8 +345,9 @@ void at91_gpio_resume(void)
static void gpio_irq_mask(struct irq_data *d)
{
- void __iomem *pio = pin_to_controller(d->irq);
- unsigned mask = pin_to_mask(d->irq);
+ unsigned pin = irq_to_gpio(d->irq);
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
if (pio)
__raw_writel(mask, pio + PIO_IDR);
@@ -355,8 +355,9 @@ static void gpio_irq_mask(struct irq_data *d)
static void gpio_irq_unmask(struct irq_data *d)
{
- void __iomem *pio = pin_to_controller(d->irq);
- unsigned mask = pin_to_mask(d->irq);
+ unsigned pin = irq_to_gpio(d->irq);
+ void __iomem *pio = pin_to_controller(pin);
+ unsigned mask = pin_to_mask(pin);
if (pio)
__raw_writel(mask, pio + PIO_IER);
@@ -384,7 +385,7 @@ static struct irq_chip gpio_irqchip = {
static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
{
- unsigned pin;
+ unsigned irq_pin;
struct irq_data *idata = irq_desc_get_irq_data(desc);
struct irq_chip *chip = irq_data_get_irq_chip(idata);
struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata);
@@ -407,12 +408,12 @@ static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
continue;
}
- pin = at91_gpio->chip.base;
+ irq_pin = gpio_to_irq(at91_gpio->chip.base);
while (isr) {
if (isr & 1)
- generic_handle_irq(pin);
- pin++;
+ generic_handle_irq(irq_pin);
+ irq_pin++;
isr >>= 1;
}
}
@@ -440,7 +441,7 @@ static int at91_gpio_show(struct seq_file *s, void *unused)
seq_printf(s, "%i:\t", j);
for (bank = 0; bank < gpio_banks; bank++) {
- unsigned pin = PIN_BASE + (32 * bank) + j;
+ unsigned pin = (32 * bank) + j;
void __iomem *pio = pin_to_controller(pin);
unsigned mask = pin_to_mask(pin);
@@ -493,10 +494,10 @@ static struct lock_class_key gpio_lock_class;
*/
void __init at91_gpio_irq_setup(void)
{
- unsigned pioc, pin;
+ unsigned pioc, irq = gpio_to_irq(0);
struct at91_gpio_chip *this, *prev;
- for (pioc = 0, pin = PIN_BASE, this = gpio_chip, prev = NULL;
+ for (pioc = 0, this = gpio_chip, prev = NULL;
pioc++ < gpio_banks;
prev = this, this++) {
unsigned id = this->bank->id;
@@ -504,16 +505,17 @@ void __init at91_gpio_irq_setup(void)
__raw_writel(~0, this->regbase + PIO_IDR);
- for (i = 0, pin = this->chip.base; i < 32; i++, pin++) {
- irq_set_lockdep_class(pin, &gpio_lock_class);
+ for (i = 0, irq = gpio_to_irq(this->chip.base); i < 32;
+ i++, irq++) {
+ irq_set_lockdep_class(irq, &gpio_lock_class);
/*
* Can use the "simple" and not "edge" handler since it's
* shorter, and the AIC handles interrupts sanely.
*/
- irq_set_chip_and_handler(pin, &gpio_irqchip,
+ irq_set_chip_and_handler(irq, &gpio_irqchip,
handle_simple_irq);
- set_irq_flags(pin, IRQF_VALID);
+ set_irq_flags(irq, IRQF_VALID);
}
/* The toplevel handler handles one bank of GPIOs, except
@@ -526,7 +528,7 @@ void __init at91_gpio_irq_setup(void)
irq_set_chip_data(id, this);
irq_set_chained_handler(id, gpio_irq_handler);
}
- pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks);
+ pr_info("AT91: %d gpio irqs in %d banks\n", irq, gpio_banks);
}
/* gpiolib support */
@@ -615,7 +617,7 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
at91_gpio = &gpio_chip[i];
at91_gpio->bank = &data[i];
- at91_gpio->chip.base = PIN_BASE + i * 32;
+ at91_gpio->chip.base = i * 32;
at91_gpio->regbase = ioremap(at91_gpio->bank->regbase, 512);
if (!at91_gpio->regbase) {
diff --git a/arch/arm/mach-at91/include/mach/gpio.h b/arch/arm/mach-at91/include/mach/gpio.h
dissimilarity index 78%
index 056dc66..5213879 100644
--- a/arch/arm/mach-at91/include/mach/gpio.h
+++ b/arch/arm/mach-at91/include/mach/gpio.h
@@ -1,228 +1,226 @@
-/*
- * arch/arm/mach-at91/include/mach/gpio.h
- *
- * Copyright (C) 2005 HP Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#ifndef __ASM_ARCH_AT91RM9200_GPIO_H
-#define __ASM_ARCH_AT91RM9200_GPIO_H
-
-#include <linux/kernel.h>
-#include <asm/irq.h>
-
-#define PIN_BASE NR_AIC_IRQS
-
-#define MAX_GPIO_BANKS 5
-#define NR_BUILTIN_GPIO (PIN_BASE + (MAX_GPIO_BANKS * 32))
-
-/* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */
-
-#define AT91_PIN_PA0 (PIN_BASE + 0x00 + 0)
-#define AT91_PIN_PA1 (PIN_BASE + 0x00 + 1)
-#define AT91_PIN_PA2 (PIN_BASE + 0x00 + 2)
-#define AT91_PIN_PA3 (PIN_BASE + 0x00 + 3)
-#define AT91_PIN_PA4 (PIN_BASE + 0x00 + 4)
-#define AT91_PIN_PA5 (PIN_BASE + 0x00 + 5)
-#define AT91_PIN_PA6 (PIN_BASE + 0x00 + 6)
-#define AT91_PIN_PA7 (PIN_BASE + 0x00 + 7)
-#define AT91_PIN_PA8 (PIN_BASE + 0x00 + 8)
-#define AT91_PIN_PA9 (PIN_BASE + 0x00 + 9)
-#define AT91_PIN_PA10 (PIN_BASE + 0x00 + 10)
-#define AT91_PIN_PA11 (PIN_BASE + 0x00 + 11)
-#define AT91_PIN_PA12 (PIN_BASE + 0x00 + 12)
-#define AT91_PIN_PA13 (PIN_BASE + 0x00 + 13)
-#define AT91_PIN_PA14 (PIN_BASE + 0x00 + 14)
-#define AT91_PIN_PA15 (PIN_BASE + 0x00 + 15)
-#define AT91_PIN_PA16 (PIN_BASE + 0x00 + 16)
-#define AT91_PIN_PA17 (PIN_BASE + 0x00 + 17)
-#define AT91_PIN_PA18 (PIN_BASE + 0x00 + 18)
-#define AT91_PIN_PA19 (PIN_BASE + 0x00 + 19)
-#define AT91_PIN_PA20 (PIN_BASE + 0x00 + 20)
-#define AT91_PIN_PA21 (PIN_BASE + 0x00 + 21)
-#define AT91_PIN_PA22 (PIN_BASE + 0x00 + 22)
-#define AT91_PIN_PA23 (PIN_BASE + 0x00 + 23)
-#define AT91_PIN_PA24 (PIN_BASE + 0x00 + 24)
-#define AT91_PIN_PA25 (PIN_BASE + 0x00 + 25)
-#define AT91_PIN_PA26 (PIN_BASE + 0x00 + 26)
-#define AT91_PIN_PA27 (PIN_BASE + 0x00 + 27)
-#define AT91_PIN_PA28 (PIN_BASE + 0x00 + 28)
-#define AT91_PIN_PA29 (PIN_BASE + 0x00 + 29)
-#define AT91_PIN_PA30 (PIN_BASE + 0x00 + 30)
-#define AT91_PIN_PA31 (PIN_BASE + 0x00 + 31)
-
-#define AT91_PIN_PB0 (PIN_BASE + 0x20 + 0)
-#define AT91_PIN_PB1 (PIN_BASE + 0x20 + 1)
-#define AT91_PIN_PB2 (PIN_BASE + 0x20 + 2)
-#define AT91_PIN_PB3 (PIN_BASE + 0x20 + 3)
-#define AT91_PIN_PB4 (PIN_BASE + 0x20 + 4)
-#define AT91_PIN_PB5 (PIN_BASE + 0x20 + 5)
-#define AT91_PIN_PB6 (PIN_BASE + 0x20 + 6)
-#define AT91_PIN_PB7 (PIN_BASE + 0x20 + 7)
-#define AT91_PIN_PB8 (PIN_BASE + 0x20 + 8)
-#define AT91_PIN_PB9 (PIN_BASE + 0x20 + 9)
-#define AT91_PIN_PB10 (PIN_BASE + 0x20 + 10)
-#define AT91_PIN_PB11 (PIN_BASE + 0x20 + 11)
-#define AT91_PIN_PB12 (PIN_BASE + 0x20 + 12)
-#define AT91_PIN_PB13 (PIN_BASE + 0x20 + 13)
-#define AT91_PIN_PB14 (PIN_BASE + 0x20 + 14)
-#define AT91_PIN_PB15 (PIN_BASE + 0x20 + 15)
-#define AT91_PIN_PB16 (PIN_BASE + 0x20 + 16)
-#define AT91_PIN_PB17 (PIN_BASE + 0x20 + 17)
-#define AT91_PIN_PB18 (PIN_BASE + 0x20 + 18)
-#define AT91_PIN_PB19 (PIN_BASE + 0x20 + 19)
-#define AT91_PIN_PB20 (PIN_BASE + 0x20 + 20)
-#define AT91_PIN_PB21 (PIN_BASE + 0x20 + 21)
-#define AT91_PIN_PB22 (PIN_BASE + 0x20 + 22)
-#define AT91_PIN_PB23 (PIN_BASE + 0x20 + 23)
-#define AT91_PIN_PB24 (PIN_BASE + 0x20 + 24)
-#define AT91_PIN_PB25 (PIN_BASE + 0x20 + 25)
-#define AT91_PIN_PB26 (PIN_BASE + 0x20 + 26)
-#define AT91_PIN_PB27 (PIN_BASE + 0x20 + 27)
-#define AT91_PIN_PB28 (PIN_BASE + 0x20 + 28)
-#define AT91_PIN_PB29 (PIN_BASE + 0x20 + 29)
-#define AT91_PIN_PB30 (PIN_BASE + 0x20 + 30)
-#define AT91_PIN_PB31 (PIN_BASE + 0x20 + 31)
-
-#define AT91_PIN_PC0 (PIN_BASE + 0x40 + 0)
-#define AT91_PIN_PC1 (PIN_BASE + 0x40 + 1)
-#define AT91_PIN_PC2 (PIN_BASE + 0x40 + 2)
-#define AT91_PIN_PC3 (PIN_BASE + 0x40 + 3)
-#define AT91_PIN_PC4 (PIN_BASE + 0x40 + 4)
-#define AT91_PIN_PC5 (PIN_BASE + 0x40 + 5)
-#define AT91_PIN_PC6 (PIN_BASE + 0x40 + 6)
-#define AT91_PIN_PC7 (PIN_BASE + 0x40 + 7)
-#define AT91_PIN_PC8 (PIN_BASE + 0x40 + 8)
-#define AT91_PIN_PC9 (PIN_BASE + 0x40 + 9)
-#define AT91_PIN_PC10 (PIN_BASE + 0x40 + 10)
-#define AT91_PIN_PC11 (PIN_BASE + 0x40 + 11)
-#define AT91_PIN_PC12 (PIN_BASE + 0x40 + 12)
-#define AT91_PIN_PC13 (PIN_BASE + 0x40 + 13)
-#define AT91_PIN_PC14 (PIN_BASE + 0x40 + 14)
-#define AT91_PIN_PC15 (PIN_BASE + 0x40 + 15)
-#define AT91_PIN_PC16 (PIN_BASE + 0x40 + 16)
-#define AT91_PIN_PC17 (PIN_BASE + 0x40 + 17)
-#define AT91_PIN_PC18 (PIN_BASE + 0x40 + 18)
-#define AT91_PIN_PC19 (PIN_BASE + 0x40 + 19)
-#define AT91_PIN_PC20 (PIN_BASE + 0x40 + 20)
-#define AT91_PIN_PC21 (PIN_BASE + 0x40 + 21)
-#define AT91_PIN_PC22 (PIN_BASE + 0x40 + 22)
-#define AT91_PIN_PC23 (PIN_BASE + 0x40 + 23)
-#define AT91_PIN_PC24 (PIN_BASE + 0x40 + 24)
-#define AT91_PIN_PC25 (PIN_BASE + 0x40 + 25)
-#define AT91_PIN_PC26 (PIN_BASE + 0x40 + 26)
-#define AT91_PIN_PC27 (PIN_BASE + 0x40 + 27)
-#define AT91_PIN_PC28 (PIN_BASE + 0x40 + 28)
-#define AT91_PIN_PC29 (PIN_BASE + 0x40 + 29)
-#define AT91_PIN_PC30 (PIN_BASE + 0x40 + 30)
-#define AT91_PIN_PC31 (PIN_BASE + 0x40 + 31)
-
-#define AT91_PIN_PD0 (PIN_BASE + 0x60 + 0)
-#define AT91_PIN_PD1 (PIN_BASE + 0x60 + 1)
-#define AT91_PIN_PD2 (PIN_BASE + 0x60 + 2)
-#define AT91_PIN_PD3 (PIN_BASE + 0x60 + 3)
-#define AT91_PIN_PD4 (PIN_BASE + 0x60 + 4)
-#define AT91_PIN_PD5 (PIN_BASE + 0x60 + 5)
-#define AT91_PIN_PD6 (PIN_BASE + 0x60 + 6)
-#define AT91_PIN_PD7 (PIN_BASE + 0x60 + 7)
-#define AT91_PIN_PD8 (PIN_BASE + 0x60 + 8)
-#define AT91_PIN_PD9 (PIN_BASE + 0x60 + 9)
-#define AT91_PIN_PD10 (PIN_BASE + 0x60 + 10)
-#define AT91_PIN_PD11 (PIN_BASE + 0x60 + 11)
-#define AT91_PIN_PD12 (PIN_BASE + 0x60 + 12)
-#define AT91_PIN_PD13 (PIN_BASE + 0x60 + 13)
-#define AT91_PIN_PD14 (PIN_BASE + 0x60 + 14)
-#define AT91_PIN_PD15 (PIN_BASE + 0x60 + 15)
-#define AT91_PIN_PD16 (PIN_BASE + 0x60 + 16)
-#define AT91_PIN_PD17 (PIN_BASE + 0x60 + 17)
-#define AT91_PIN_PD18 (PIN_BASE + 0x60 + 18)
-#define AT91_PIN_PD19 (PIN_BASE + 0x60 + 19)
-#define AT91_PIN_PD20 (PIN_BASE + 0x60 + 20)
-#define AT91_PIN_PD21 (PIN_BASE + 0x60 + 21)
-#define AT91_PIN_PD22 (PIN_BASE + 0x60 + 22)
-#define AT91_PIN_PD23 (PIN_BASE + 0x60 + 23)
-#define AT91_PIN_PD24 (PIN_BASE + 0x60 + 24)
-#define AT91_PIN_PD25 (PIN_BASE + 0x60 + 25)
-#define AT91_PIN_PD26 (PIN_BASE + 0x60 + 26)
-#define AT91_PIN_PD27 (PIN_BASE + 0x60 + 27)
-#define AT91_PIN_PD28 (PIN_BASE + 0x60 + 28)
-#define AT91_PIN_PD29 (PIN_BASE + 0x60 + 29)
-#define AT91_PIN_PD30 (PIN_BASE + 0x60 + 30)
-#define AT91_PIN_PD31 (PIN_BASE + 0x60 + 31)
-
-#define AT91_PIN_PE0 (PIN_BASE + 0x80 + 0)
-#define AT91_PIN_PE1 (PIN_BASE + 0x80 + 1)
-#define AT91_PIN_PE2 (PIN_BASE + 0x80 + 2)
-#define AT91_PIN_PE3 (PIN_BASE + 0x80 + 3)
-#define AT91_PIN_PE4 (PIN_BASE + 0x80 + 4)
-#define AT91_PIN_PE5 (PIN_BASE + 0x80 + 5)
-#define AT91_PIN_PE6 (PIN_BASE + 0x80 + 6)
-#define AT91_PIN_PE7 (PIN_BASE + 0x80 + 7)
-#define AT91_PIN_PE8 (PIN_BASE + 0x80 + 8)
-#define AT91_PIN_PE9 (PIN_BASE + 0x80 + 9)
-#define AT91_PIN_PE10 (PIN_BASE + 0x80 + 10)
-#define AT91_PIN_PE11 (PIN_BASE + 0x80 + 11)
-#define AT91_PIN_PE12 (PIN_BASE + 0x80 + 12)
-#define AT91_PIN_PE13 (PIN_BASE + 0x80 + 13)
-#define AT91_PIN_PE14 (PIN_BASE + 0x80 + 14)
-#define AT91_PIN_PE15 (PIN_BASE + 0x80 + 15)
-#define AT91_PIN_PE16 (PIN_BASE + 0x80 + 16)
-#define AT91_PIN_PE17 (PIN_BASE + 0x80 + 17)
-#define AT91_PIN_PE18 (PIN_BASE + 0x80 + 18)
-#define AT91_PIN_PE19 (PIN_BASE + 0x80 + 19)
-#define AT91_PIN_PE20 (PIN_BASE + 0x80 + 20)
-#define AT91_PIN_PE21 (PIN_BASE + 0x80 + 21)
-#define AT91_PIN_PE22 (PIN_BASE + 0x80 + 22)
-#define AT91_PIN_PE23 (PIN_BASE + 0x80 + 23)
-#define AT91_PIN_PE24 (PIN_BASE + 0x80 + 24)
-#define AT91_PIN_PE25 (PIN_BASE + 0x80 + 25)
-#define AT91_PIN_PE26 (PIN_BASE + 0x80 + 26)
-#define AT91_PIN_PE27 (PIN_BASE + 0x80 + 27)
-#define AT91_PIN_PE28 (PIN_BASE + 0x80 + 28)
-#define AT91_PIN_PE29 (PIN_BASE + 0x80 + 29)
-#define AT91_PIN_PE30 (PIN_BASE + 0x80 + 30)
-#define AT91_PIN_PE31 (PIN_BASE + 0x80 + 31)
-
-#ifndef __ASSEMBLY__
-/* setup setup routines, called from board init or driver probe() */
-extern int __init_or_module at91_set_GPIO_periph(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup);
-extern int __init_or_module at91_set_gpio_output(unsigned pin, int value);
-extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on);
-extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on);
-
-/* callable at any time */
-extern int at91_set_gpio_value(unsigned pin, int value);
-extern int at91_get_gpio_value(unsigned pin);
-
-/* callable only from core power-management code */
-extern void at91_gpio_suspend(void);
-extern void at91_gpio_resume(void);
-
-/*-------------------------------------------------------------------------*/
-
-/* wrappers for "new style" GPIO calls. the old AT91-specific ones should
- * eventually be removed (along with this errno.h inclusion), and the
- * gpio request/free calls should probably be implemented.
- */
-
-#include <asm/errno.h>
-#include <asm-generic/gpio.h> /* cansleep wrappers */
-
-#define gpio_get_value __gpio_get_value
-#define gpio_set_value __gpio_set_value
-#define gpio_cansleep __gpio_cansleep
-
-#define gpio_to_irq(gpio) (gpio)
-#define irq_to_gpio(irq) (irq)
-
-#endif /* __ASSEMBLY__ */
-
-#endif
+/*
+ * arch/arm/mach-at91/include/mach/gpio.h
+ *
+ * Copyright (C) 2005 HP Labs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#ifndef __ASM_ARCH_AT91RM9200_GPIO_H
+#define __ASM_ARCH_AT91RM9200_GPIO_H
+
+#include <linux/kernel.h>
+#include <asm/irq.h>
+
+#define MAX_GPIO_BANKS 5
+#define NR_BUILTIN_GPIO (MAX_GPIO_BANKS * 32)
+
+/* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */
+
+#define AT91_PIN_PA0 (0x00 + 0)
+#define AT91_PIN_PA1 (0x00 + 1)
+#define AT91_PIN_PA2 (0x00 + 2)
+#define AT91_PIN_PA3 (0x00 + 3)
+#define AT91_PIN_PA4 (0x00 + 4)
+#define AT91_PIN_PA5 (0x00 + 5)
+#define AT91_PIN_PA6 (0x00 + 6)
+#define AT91_PIN_PA7 (0x00 + 7)
+#define AT91_PIN_PA8 (0x00 + 8)
+#define AT91_PIN_PA9 (0x00 + 9)
+#define AT91_PIN_PA10 (0x00 + 10)
+#define AT91_PIN_PA11 (0x00 + 11)
+#define AT91_PIN_PA12 (0x00 + 12)
+#define AT91_PIN_PA13 (0x00 + 13)
+#define AT91_PIN_PA14 (0x00 + 14)
+#define AT91_PIN_PA15 (0x00 + 15)
+#define AT91_PIN_PA16 (0x00 + 16)
+#define AT91_PIN_PA17 (0x00 + 17)
+#define AT91_PIN_PA18 (0x00 + 18)
+#define AT91_PIN_PA19 (0x00 + 19)
+#define AT91_PIN_PA20 (0x00 + 20)
+#define AT91_PIN_PA21 (0x00 + 21)
+#define AT91_PIN_PA22 (0x00 + 22)
+#define AT91_PIN_PA23 (0x00 + 23)
+#define AT91_PIN_PA24 (0x00 + 24)
+#define AT91_PIN_PA25 (0x00 + 25)
+#define AT91_PIN_PA26 (0x00 + 26)
+#define AT91_PIN_PA27 (0x00 + 27)
+#define AT91_PIN_PA28 (0x00 + 28)
+#define AT91_PIN_PA29 (0x00 + 29)
+#define AT91_PIN_PA30 (0x00 + 30)
+#define AT91_PIN_PA31 (0x00 + 31)
+
+#define AT91_PIN_PB0 (0x20 + 0)
+#define AT91_PIN_PB1 (0x20 + 1)
+#define AT91_PIN_PB2 (0x20 + 2)
+#define AT91_PIN_PB3 (0x20 + 3)
+#define AT91_PIN_PB4 (0x20 + 4)
+#define AT91_PIN_PB5 (0x20 + 5)
+#define AT91_PIN_PB6 (0x20 + 6)
+#define AT91_PIN_PB7 (0x20 + 7)
+#define AT91_PIN_PB8 (0x20 + 8)
+#define AT91_PIN_PB9 (0x20 + 9)
+#define AT91_PIN_PB10 (0x20 + 10)
+#define AT91_PIN_PB11 (0x20 + 11)
+#define AT91_PIN_PB12 (0x20 + 12)
+#define AT91_PIN_PB13 (0x20 + 13)
+#define AT91_PIN_PB14 (0x20 + 14)
+#define AT91_PIN_PB15 (0x20 + 15)
+#define AT91_PIN_PB16 (0x20 + 16)
+#define AT91_PIN_PB17 (0x20 + 17)
+#define AT91_PIN_PB18 (0x20 + 18)
+#define AT91_PIN_PB19 (0x20 + 19)
+#define AT91_PIN_PB20 (0x20 + 20)
+#define AT91_PIN_PB21 (0x20 + 21)
+#define AT91_PIN_PB22 (0x20 + 22)
+#define AT91_PIN_PB23 (0x20 + 23)
+#define AT91_PIN_PB24 (0x20 + 24)
+#define AT91_PIN_PB25 (0x20 + 25)
+#define AT91_PIN_PB26 (0x20 + 26)
+#define AT91_PIN_PB27 (0x20 + 27)
+#define AT91_PIN_PB28 (0x20 + 28)
+#define AT91_PIN_PB29 (0x20 + 29)
+#define AT91_PIN_PB30 (0x20 + 30)
+#define AT91_PIN_PB31 (0x20 + 31)
+
+#define AT91_PIN_PC0 (0x40 + 0)
+#define AT91_PIN_PC1 (0x40 + 1)
+#define AT91_PIN_PC2 (0x40 + 2)
+#define AT91_PIN_PC3 (0x40 + 3)
+#define AT91_PIN_PC4 (0x40 + 4)
+#define AT91_PIN_PC5 (0x40 + 5)
+#define AT91_PIN_PC6 (0x40 + 6)
+#define AT91_PIN_PC7 (0x40 + 7)
+#define AT91_PIN_PC8 (0x40 + 8)
+#define AT91_PIN_PC9 (0x40 + 9)
+#define AT91_PIN_PC10 (0x40 + 10)
+#define AT91_PIN_PC11 (0x40 + 11)
+#define AT91_PIN_PC12 (0x40 + 12)
+#define AT91_PIN_PC13 (0x40 + 13)
+#define AT91_PIN_PC14 (0x40 + 14)
+#define AT91_PIN_PC15 (0x40 + 15)
+#define AT91_PIN_PC16 (0x40 + 16)
+#define AT91_PIN_PC17 (0x40 + 17)
+#define AT91_PIN_PC18 (0x40 + 18)
+#define AT91_PIN_PC19 (0x40 + 19)
+#define AT91_PIN_PC20 (0x40 + 20)
+#define AT91_PIN_PC21 (0x40 + 21)
+#define AT91_PIN_PC22 (0x40 + 22)
+#define AT91_PIN_PC23 (0x40 + 23)
+#define AT91_PIN_PC24 (0x40 + 24)
+#define AT91_PIN_PC25 (0x40 + 25)
+#define AT91_PIN_PC26 (0x40 + 26)
+#define AT91_PIN_PC27 (0x40 + 27)
+#define AT91_PIN_PC28 (0x40 + 28)
+#define AT91_PIN_PC29 (0x40 + 29)
+#define AT91_PIN_PC30 (0x40 + 30)
+#define AT91_PIN_PC31 (0x40 + 31)
+
+#define AT91_PIN_PD0 (0x60 + 0)
+#define AT91_PIN_PD1 (0x60 + 1)
+#define AT91_PIN_PD2 (0x60 + 2)
+#define AT91_PIN_PD3 (0x60 + 3)
+#define AT91_PIN_PD4 (0x60 + 4)
+#define AT91_PIN_PD5 (0x60 + 5)
+#define AT91_PIN_PD6 (0x60 + 6)
+#define AT91_PIN_PD7 (0x60 + 7)
+#define AT91_PIN_PD8 (0x60 + 8)
+#define AT91_PIN_PD9 (0x60 + 9)
+#define AT91_PIN_PD10 (0x60 + 10)
+#define AT91_PIN_PD11 (0x60 + 11)
+#define AT91_PIN_PD12 (0x60 + 12)
+#define AT91_PIN_PD13 (0x60 + 13)
+#define AT91_PIN_PD14 (0x60 + 14)
+#define AT91_PIN_PD15 (0x60 + 15)
+#define AT91_PIN_PD16 (0x60 + 16)
+#define AT91_PIN_PD17 (0x60 + 17)
+#define AT91_PIN_PD18 (0x60 + 18)
+#define AT91_PIN_PD19 (0x60 + 19)
+#define AT91_PIN_PD20 (0x60 + 20)
+#define AT91_PIN_PD21 (0x60 + 21)
+#define AT91_PIN_PD22 (0x60 + 22)
+#define AT91_PIN_PD23 (0x60 + 23)
+#define AT91_PIN_PD24 (0x60 + 24)
+#define AT91_PIN_PD25 (0x60 + 25)
+#define AT91_PIN_PD26 (0x60 + 26)
+#define AT91_PIN_PD27 (0x60 + 27)
+#define AT91_PIN_PD28 (0x60 + 28)
+#define AT91_PIN_PD29 (0x60 + 29)
+#define AT91_PIN_PD30 (0x60 + 30)
+#define AT91_PIN_PD31 (0x60 + 31)
+
+#define AT91_PIN_PE0 (0x80 + 0)
+#define AT91_PIN_PE1 (0x80 + 1)
+#define AT91_PIN_PE2 (0x80 + 2)
+#define AT91_PIN_PE3 (0x80 + 3)
+#define AT91_PIN_PE4 (0x80 + 4)
+#define AT91_PIN_PE5 (0x80 + 5)
+#define AT91_PIN_PE6 (0x80 + 6)
+#define AT91_PIN_PE7 (0x80 + 7)
+#define AT91_PIN_PE8 (0x80 + 8)
+#define AT91_PIN_PE9 (0x80 + 9)
+#define AT91_PIN_PE10 (0x80 + 10)
+#define AT91_PIN_PE11 (0x80 + 11)
+#define AT91_PIN_PE12 (0x80 + 12)
+#define AT91_PIN_PE13 (0x80 + 13)
+#define AT91_PIN_PE14 (0x80 + 14)
+#define AT91_PIN_PE15 (0x80 + 15)
+#define AT91_PIN_PE16 (0x80 + 16)
+#define AT91_PIN_PE17 (0x80 + 17)
+#define AT91_PIN_PE18 (0x80 + 18)
+#define AT91_PIN_PE19 (0x80 + 19)
+#define AT91_PIN_PE20 (0x80 + 20)
+#define AT91_PIN_PE21 (0x80 + 21)
+#define AT91_PIN_PE22 (0x80 + 22)
+#define AT91_PIN_PE23 (0x80 + 23)
+#define AT91_PIN_PE24 (0x80 + 24)
+#define AT91_PIN_PE25 (0x80 + 25)
+#define AT91_PIN_PE26 (0x80 + 26)
+#define AT91_PIN_PE27 (0x80 + 27)
+#define AT91_PIN_PE28 (0x80 + 28)
+#define AT91_PIN_PE29 (0x80 + 29)
+#define AT91_PIN_PE30 (0x80 + 30)
+#define AT91_PIN_PE31 (0x80 + 31)
+
+#ifndef __ASSEMBLY__
+/* setup setup routines, called from board init or driver probe() */
+extern int __init_or_module at91_set_GPIO_periph(unsigned pin, int use_pullup);
+extern int __init_or_module at91_set_A_periph(unsigned pin, int use_pullup);
+extern int __init_or_module at91_set_B_periph(unsigned pin, int use_pullup);
+extern int __init_or_module at91_set_gpio_input(unsigned pin, int use_pullup);
+extern int __init_or_module at91_set_gpio_output(unsigned pin, int value);
+extern int __init_or_module at91_set_deglitch(unsigned pin, int is_on);
+extern int __init_or_module at91_set_multi_drive(unsigned pin, int is_on);
+
+/* callable at any time */
+extern int at91_set_gpio_value(unsigned pin, int value);
+extern int at91_get_gpio_value(unsigned pin);
+
+/* callable only from core power-management code */
+extern void at91_gpio_suspend(void);
+extern void at91_gpio_resume(void);
+
+/*-------------------------------------------------------------------------*/
+
+/* wrappers for "new style" GPIO calls. the old AT91-specific ones should
+ * eventually be removed (along with this errno.h inclusion), and the
+ * gpio request/free calls should probably be implemented.
+ */
+
+#include <asm/errno.h>
+#include <asm-generic/gpio.h> /* cansleep wrappers */
+
+#define gpio_get_value __gpio_get_value
+#define gpio_set_value __gpio_set_value
+#define gpio_cansleep __gpio_cansleep
+
+#define gpio_to_irq(gpio) (gpio + NR_AIC_IRQS)
+#define irq_to_gpio(irq) (irq - NR_AIC_IRQS)
+
+#endif /* __ASSEMBLY__ */
+
+#endif
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 11/11] at91/gpio: fix display of number of irq setuped
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
` (8 preceding siblings ...)
2011-09-19 14:03 ` [PATCH 10/11] at91/gpio: drop PIN_BASE Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-19 14:03 ` Jean-Christophe PLAGNIOL-VILLARD
9 siblings, 0 replies; 13+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2011-09-19 14:03 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
---
arch/arm/mach-at91/gpio.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c
index e709406..743f668 100644
--- a/arch/arm/mach-at91/gpio.c
+++ b/arch/arm/mach-at91/gpio.c
@@ -528,7 +528,7 @@ void __init at91_gpio_irq_setup(void)
irq_set_chip_data(id, this);
irq_set_chained_handler(id, gpio_irq_handler);
}
- pr_info("AT91: %d gpio irqs in %d banks\n", irq, gpio_banks);
+ pr_info("AT91: %d gpio irqs in %d banks\n", irq - gpio_to_irq(0), gpio_banks);
}
/* gpiolib support */
--
1.7.5.4
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH 08/11] at92/udc: use gpio_is_valid to check the gpio
2011-09-19 14:03 ` [PATCH 08/11] at92/udc: " Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-20 9:52 ` Sebastian Andrzej Siewior
0 siblings, 0 replies; 13+ messages in thread
From: Sebastian Andrzej Siewior @ 2011-09-20 9:52 UTC (permalink / raw)
To: linux-arm-kernel
* Jean-Christophe PLAGNIOL-VILLARD | 2011-09-19 16:03:19 [+0200]:
>Hi,
Hi,
> I'd like to apply this patch via AT91 with the whole gpio patch series
Felipe is on vacation until next week. The cleanup looks nice so I guess
he wouldn't mind if you push this with the whole gpio series.
>Best Regards,
>J.
Sebastian
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH 02/11] at91/boards: use -1 for invalid gpio
2011-09-19 12:51 ` [PATCH 02/11] at91/boards: use -1 for invalid gpio Jean-Christophe PLAGNIOL-VILLARD
@ 2011-09-21 9:28 ` Nicolas Ferre
0 siblings, 0 replies; 13+ messages in thread
From: Nicolas Ferre @ 2011-09-21 9:28 UTC (permalink / raw)
To: linux-arm-kernel
Le 19/09/2011 14:51, Jean-Christophe PLAGNIOL-VILLARD :
> this will allow to use gpio_is_valid
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
[..]
> ---
> 34 files changed, 141 insertions(+), 50 deletions(-)
>
> diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c
> index 5aa5885..17d9163 100644
> --- a/arch/arm/mach-at91/board-1arm.c
> +++ b/arch/arm/mach-at91/board-1arm.c
> @@ -70,6 +70,7 @@ static struct at91_eth_data __initdata onearm_eth_data = {
>
> static struct at91_usbh_data __initdata onearm_usbh_data = {
> .ports = 1,
> + .vbus_pin = {-1, -1},
I would prefer to use "-EINVAL" as stated in the documentation.
Best regards,
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2011-09-21 9:28 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-09-19 12:51 [PATCH 01/11] at91/gpio: make gpio register base soc independant Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 02/11] at91/boards: use -1 for invalid gpio Jean-Christophe PLAGNIOL-VILLARD
2011-09-21 9:28 ` Nicolas Ferre
2011-09-19 12:51 ` [PATCH 03/11] at91/soc: use gpio_is_valid to check the gpio Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 04/11] at91/pata: " Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 12:51 ` [PATCH 05/11] at91/ide: " Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 06/11] at91/mmc: " Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 07/11] at92/nand: " Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 08/11] at92/udc: " Jean-Christophe PLAGNIOL-VILLARD
2011-09-20 9:52 ` Sebastian Andrzej Siewior
2011-09-19 14:03 ` [PATCH 09/11] at92/ohci: " Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 10/11] at91/gpio: drop PIN_BASE Jean-Christophe PLAGNIOL-VILLARD
2011-09-19 14:03 ` [PATCH 11/11] at91/gpio: fix display of number of irq setuped Jean-Christophe PLAGNIOL-VILLARD
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).