From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 3/5] regulator: helper routine to extract regulator_init_data
Date: Thu, 20 Oct 2011 15:09:14 -0700 [thread overview]
Message-ID: <20111020220914.GP3842@atomide.com> (raw)
In-Reply-To: <20111020214225.GB22709@opensource.wolfsonmicro.com>
* Mark Brown <broonie@opensource.wolfsonmicro.com> [111020 14:08]:
> On Thu, Oct 20, 2011 at 01:10:55PM -0700, Tony Lindgren wrote:
>
> > We still need to figure out how to get the above board specific
> > data to the device driver probe in a way where we can avoid having
> > platform glue code. Any thoughts on that?
>
> I think we should just not bother with most of the above and see if
> anyone notices, with the exception of always on and status changes it's
> vanishingly rare for anyone to actually do anything constructive with
> them.
OK
> Neither of the two I mentioned are Linux specific either, they mean
> somehing useful for any OS it's just that the decision is policy which
> is going to depend on the OS version. Status changes we can probably
> allow people to enable, it'll just mean that older device trees won't
> get good power use out of newer kernels and if you move to an older
> kernel things will start exploding as drivers loose regulator support.
> Always on we can probably live without, it's a combination of
> overspecification and interaction with _has_full_constraints() which
> isn't represented in this binding anyway.
Yeah, lot of these are "how the regulator using driver is using
the regulator" or "how the operating system is using the regulator"
type policies.
Regards,
Tony
next prev parent reply other threads:[~2011-10-20 22:09 UTC|newest]
Thread overview: 89+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-10-10 16:19 [PATCH v2 0/5] Device tree support for regulators Rajendra Nayak
2011-10-10 16:19 ` [PATCH v2 1/5] regulator: twl: Remove hardcoded board constraints from driver Rajendra Nayak
2011-10-10 16:25 ` Mark Brown
2011-10-10 16:34 ` Rajendra Nayak
2011-10-10 16:19 ` [PATCH v2 2/5] dt: add empty dt helpers for non-dt build Rajendra Nayak
2011-10-13 18:32 ` Grant Likely
2011-10-10 16:19 ` [PATCH v2 3/5] regulator: helper routine to extract regulator_init_data Rajendra Nayak
2011-10-10 17:22 ` Mark Brown
2011-10-11 5:59 ` Rajendra Nayak
2011-10-13 18:38 ` Grant Likely
2011-10-13 22:12 ` Mark Brown
2011-10-13 18:40 ` Grant Likely
2011-10-16 14:55 ` Shawn Guo
2011-10-17 4:17 ` Rajendra Nayak
2011-10-18 11:58 ` Shawn Guo
2011-10-18 16:00 ` Mark Brown
2011-10-19 5:33 ` Shawn Guo
2011-10-19 14:47 ` Mark Brown
2011-10-19 15:04 ` Shawn Guo
2011-10-19 15:10 ` Mark Brown
2011-10-20 3:42 ` Rajendra Nayak
2011-10-20 9:41 ` Mark Brown
2011-10-20 12:10 ` Rajendra Nayak
2011-10-20 16:27 ` Tony Lindgren
2011-10-20 16:40 ` Mark Brown
2011-10-20 17:05 ` Tony Lindgren
2011-10-20 17:22 ` Tony Lindgren
2011-10-20 19:57 ` Mark Brown
2011-10-20 20:10 ` Tony Lindgren
2011-10-20 21:42 ` Mark Brown
2011-10-20 22:09 ` Tony Lindgren [this message]
2011-10-24 9:07 ` Grant Likely
2011-10-20 19:56 ` Mark Brown
2011-10-18 13:20 ` Shawn Guo
2011-10-19 11:35 ` Rajendra Nayak
2011-10-19 14:42 ` Shawn Guo
2011-10-19 14:50 ` Mark Brown
2011-10-20 5:18 ` Rajendra Nayak
2011-10-20 6:14 ` Shawn Guo
2011-10-20 12:09 ` Rajendra Nayak
2011-10-21 8:23 ` Shawn Guo
2011-10-21 8:41 ` Rajendra Nayak
2011-10-21 11:58 ` Shawn Guo
2011-10-24 6:02 ` Rajendra Nayak
2011-10-24 7:34 ` Mark Brown
2011-10-24 8:17 ` Grant Likely
2011-10-24 8:53 ` Rajendra Nayak
2011-10-24 9:19 ` Mark Brown
2011-10-24 10:05 ` Rajendra Nayak
2011-10-24 9:23 ` Shawn Guo
2011-10-24 9:02 ` Shawn Guo
2011-10-24 8:56 ` Rajendra Nayak
2011-10-24 9:11 ` Shawn Guo
2011-10-24 9:13 ` Rajendra Nayak
2011-10-24 13:47 ` Shawn Guo
2011-10-25 6:00 ` Rajendra Nayak
2011-10-25 6:26 ` Rajendra Nayak
2011-10-25 6:52 ` Shawn Guo
2011-10-25 6:56 ` Rajendra Nayak
2011-10-25 7:20 ` Shawn Guo
2011-10-25 7:13 ` Rajendra Nayak
2011-10-25 7:42 ` Shawn Guo
2011-10-24 11:35 ` Grant Likely
2011-10-24 9:24 ` Grant Likely
2011-10-24 9:39 ` Mark Brown
2011-10-24 13:04 ` Shawn Guo
2011-10-24 13:06 ` Mark Brown
2011-10-24 13:40 ` Shawn Guo
2011-10-24 13:49 ` Mark Brown
2011-10-24 14:47 ` Shawn Guo
2011-10-25 7:11 ` Mark Brown
2011-10-24 13:59 ` Grant Likely
2011-10-24 14:51 ` Shawn Guo
2011-10-24 14:56 ` Grant Likely
2011-10-24 15:51 ` Shawn Guo
2011-10-24 22:21 ` Grant Likely
2011-10-25 6:10 ` Rajendra Nayak
2011-10-25 7:08 ` Shawn Guo
2011-10-25 7:01 ` Rajendra Nayak
2011-10-25 7:28 ` Shawn Guo
2011-10-10 16:19 ` [PATCH v2 4/5] regulator: adapt fixed regulator driver to dt Rajendra Nayak
2011-10-13 18:43 ` Grant Likely
2011-10-10 16:19 ` [PATCH v2 5/5] regulator: map consumer regulator based on device tree Rajendra Nayak
2011-10-10 17:35 ` Mark Brown
2011-10-11 5:49 ` Rajendra Nayak
2011-10-11 7:08 ` Nayak, Rajendra
2011-10-13 16:52 ` Mark Brown
2011-10-13 18:46 ` Grant Likely
2011-10-18 13:33 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20111020220914.GP3842@atomide.com \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).