[PATCH 2a/5 v2] ARM: OMAP1: select clock rate by CPU type

[tony@atomide.com (Tony Lindgren)]

* Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> [111130 12:23]:
> DPLL1 reprogramming to a different rate is actually blocked inside
> omap1_select_table_rate(), resulting in the defalut rate of 60 MHz
> always used instead of the one selected in .config. OTOH, in
> omap1_defconfig we currently rely on Kconfig options for the supported
> MHz rates in case of boards which boot with dpll1 not set correctly by
> their boot loaders.
> 
> This means that before we allow for reprogramming of dpll1 rate, we
> should prevent from incompatible clock rates being selected, otherwise
> omap1_defconfig will stop booting on boards with imperfect boot loaders,
> as it would always try to change to 216MHz.
> 
> Expand omap1_rate_table with flags for different CPU types and match
> them while selecting clock rates. The idea is stolen from current
> omap24xx clock rate selection algorithm.
> 
> Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
> ---
> Hi,
> Since there is no response to patch 2a/5 "Remove unsafe clock values 
> from omap1_defconfig" yet, while rc4 is probably almost out:

Well I'm still wondering what would be the absolute minimal fixe(s)
for the -rc cycle?

Is the problem just that currently with omap1_defconfig boards boot at
the bootloader rate, or at the safe 60MHz unless the .config is changed?
If so, I think that's OK for now as fixing it properly requires what
this patch is doing.
 
> If there are reasons for keeping high clock rates selected in
> omap1_defconfig, and those reasons are more important than fixing bugs
> which prevent some boards from working correctly under 3.2, here is an
> alternative, low intrusive solution which should allow booting from
> omap1_defconfig at correct speeds, selected by CPU type. If the idea is
> acceptable, please review the CPU per clock rate selections I made,
> since I'm not sure about their correctness, perhaps except CK_1510,
> which is based on my own experience with Amstrad Delta. I'll fix that if
> necessary.

Great, this looks like pretty much what I had in mind for the next
merge window! Just one comment below.

 
> @@ -21,38 +22,52 @@ struct mpu_rate omap1_rate_table[] = {
>  	 * armdiv, dspdiv, dspmmu, tcdiv, perdiv, lcddiv
>  	 */
>  #if defined(CONFIG_OMAP_ARM_216MHZ)
> -	{ 216000000, 12000000, 216000000, 0x050d, 0x2910 }, /* 1/1/2/2/2/8 */
> +	{ 216000000, 12000000, 216000000, 0x050d, 0x2910, /* 1/1/2/2/2/8 */
> +			CK_16XX },
>  #endif
>  #if defined(CONFIG_OMAP_ARM_195MHZ)
> -	{ 195000000, 13000000, 195000000, 0x050e, 0x2790 }, /* 1/1/2/2/4/8 */
> +	{ 195000000, 13000000, 195000000, 0x050e, 0x2790, /* 1/1/2/2/4/8 */
> +			CK_7XX|CK_16XX },
>  #endif
>  #if defined(CONFIG_OMAP_ARM_192MHZ)
...

We should also now be able to remove all the CONFIG_OMAP_ARM_XXXMHZ options
too, right?

Regards,

Tony