[PATCH 0/7] Cragganmore updates for 3.3

linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed

* [PATCH 0/7] Cragganmore updates for 3.3
@ 2011-11-29 13:30 Mark Brown
  2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
  2011-12-01 10:29 ` [PATCH 0/7] Cragganmore updates for 3.3 Kukjin Kim
  0 siblings, 2 replies; 10+ messages in thread
From: Mark Brown @ 2011-11-29 13:30 UTC (permalink / raw)
  To: linux-arm-kernel

This patch series is all the pending updates for Cragganmore for 3.3.
With the exception of the final patch for Littlemill they've all been
posted before, some a while ago now, but I've not seen any feedback yet.
They're all available on a git branch in case it's helpful to pull them:

The following changes since commit caca6a03d365883564885f2c1da3e88dcf65d139:

  Linux 3.2-rc3 (2011-11-23 20:20:28 -0800)

are available in the git repository at:
  git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc.git updates/cragganmore

Mark Brown (7):
      ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore
      ARM: S3C64XX: Use software initiated powerdown for Cragganmore
      ARM: S3C64XX: Configure WM1250 EV1 GPIOs on Cragganmore
      ARM: S3C64XX: Improve logging of unknown Cragganmore module types
      ARM: S3C64XX: Run Tobermory interrupts in the default mode
      ARM: S3C64XX: Hook up platform data for Kilchomin module on Cragganmore
      ARM: S3C64XX: Hook up Littlemill audio card on Cragganmore

 arch/arm/mach-s3c64xx/include/mach/crag6410.h |    6 ++-
 arch/arm/mach-s3c64xx/include/mach/irqs.h     |    2 +-
 arch/arm/mach-s3c64xx/mach-crag6410-module.c  |   56 +++++++++++++++++++++++-
 arch/arm/mach-s3c64xx/mach-crag6410.c         |   30 ++++++++++++-
 4 files changed, 86 insertions(+), 8 deletions(-)

^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore
  2011-11-29 13:30 [PATCH 0/7] Cragganmore updates for 3.3 Mark Brown
@ 2011-11-29 13:30 ` Mark Brown
  2011-11-29 13:30   ` [PATCH 2/7] ARM: S3C64XX: Use software initiated powerdown for Cragganmore Mark Brown
                     ` (5 more replies)
  2011-12-01 10:29 ` [PATCH 0/7] Cragganmore updates for 3.3 Kukjin Kim
  1 sibling, 6 replies; 10+ messages in thread
From: Mark Brown @ 2011-11-29 13:30 UTC (permalink / raw)
  To: linux-arm-kernel

The S3C I2C driver defaults to a rather low 66kHz, ask for 400kHz for
a bit of a speed boost.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
 arch/arm/mach-s3c64xx/mach-crag6410.c |    7 ++++++-
 1 files changed, 6 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c
index d04b654..b9a052a 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410.c
@@ -634,6 +634,11 @@ static struct i2c_board_info i2c_devs1[] __initdata = {
 	{ I2C_BOARD_INFO("wm1250-ev1", 0x27) },
 };
 
+static struct s3c2410_platform_i2c i2c1_pdata = {
+	.frequency = 400000,
+	.bus_num = 1,
+};
+
 static void __init crag6410_map_io(void)
 {
 	s3c64xx_init_io(NULL, 0);
@@ -692,7 +697,7 @@ static void __init crag6410_machine_init(void)
 	s3c_sdhci2_set_platdata(&crag6410_hsmmc2_pdata);
 
 	s3c_i2c0_set_platdata(&i2c0_pdata);
-	s3c_i2c1_set_platdata(NULL);
+	s3c_i2c1_set_platdata(&i2c1_pdata);
 	s3c_fb_set_platdata(&crag6410_lcd_pdata);
 
 	i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
-- 
1.7.7.3

^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH 2/7] ARM: S3C64XX: Use software initiated powerdown for Cragganmore
  2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
@ 2011-11-29 13:30   ` Mark Brown
  2011-11-29 13:30   ` [PATCH 3/7] ARM: S3C64XX: Configure WM1250 EV1 GPIOs on Cragganmore Mark Brown
                     ` (4 subsequent siblings)
  5 siblings, 0 replies; 10+ messages in thread
From: Mark Brown @ 2011-11-29 13:30 UTC (permalink / raw)
  To: linux-arm-kernel

Since the two PMICs are independent we initiate a shutdown on each.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
 arch/arm/mach-s3c64xx/mach-crag6410.c |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c
index b9a052a..3882c2f 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410.c
@@ -501,6 +501,7 @@ static struct wm831x_pdata crag_pmic_pdata __initdata = {
 	.wm831x_num = 1,
 	.irq_base = BANFF_PMIC_IRQ_BASE,
 	.gpio_base = GPIO_BOARD_START + 8,
+	.soft_shutdown = true,
 
 	.backup = &banff_backup_pdata,
 
@@ -605,6 +606,7 @@ static struct wm831x_pdata glenfarclas_pmic_pdata __initdata = {
 	.wm831x_num = 2,
 	.irq_base = GLENFARCLAS_PMIC_IRQ_BASE,
 	.gpio_base = GLENFARCLAS_PMIC_GPIO_BASE,
+	.soft_shutdown = true,
 
 	.gpio_defaults = {
 		/* GPIO1-3: IRQ inputs, rising edge triggered, CMOS */
-- 
1.7.7.3

^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH 3/7] ARM: S3C64XX: Configure WM1250 EV1 GPIOs on Cragganmore
  2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
  2011-11-29 13:30   ` [PATCH 2/7] ARM: S3C64XX: Use software initiated powerdown for Cragganmore Mark Brown
@ 2011-11-29 13:30   ` Mark Brown
  2011-11-29 13:30   ` [PATCH 4/7] ARM: S3C64XX: Improve logging of unknown Cragganmore module types Mark Brown
                     ` (3 subsequent siblings)
  5 siblings, 0 replies; 10+ messages in thread
From: Mark Brown @ 2011-11-29 13:30 UTC (permalink / raw)
  To: linux-arm-kernel

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
 arch/arm/mach-s3c64xx/mach-crag6410.c |   15 ++++++++++++++-
 1 files changed, 14 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c
index 3882c2f..05f598f 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410.c
@@ -37,6 +37,8 @@
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
 
+#include <sound/wm1250-ev1.h>
+
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
@@ -624,6 +626,16 @@ static struct wm831x_pdata glenfarclas_pmic_pdata __initdata = {
 	.disable_touch = true,
 };
 
+static struct wm1250_ev1_pdata wm1250_ev1_pdata = {
+	.gpios = {
+		[WM1250_EV1_GPIO_CLK_ENA] = S3C64XX_GPN(12),
+		[WM1250_EV1_GPIO_CLK_SEL0] = S3C64XX_GPL(12),
+		[WM1250_EV1_GPIO_CLK_SEL1] = S3C64XX_GPL(13),
+		[WM1250_EV1_GPIO_OSR] = S3C64XX_GPL(14),
+		[WM1250_EV1_GPIO_MASTER] = S3C64XX_GPL(8),
+	},
+};
+
 static struct i2c_board_info i2c_devs1[] __initdata = {
 	{ I2C_BOARD_INFO("wm8311", 0x34),
 	  .irq = S3C_EINT(0),
@@ -633,7 +645,8 @@ static struct i2c_board_info i2c_devs1[] __initdata = {
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x25) },
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x26) },
 
-	{ I2C_BOARD_INFO("wm1250-ev1", 0x27) },
+	{ I2C_BOARD_INFO("wm1250-ev1", 0x27),
+	  .platform_data = &wm1250_ev1_pdata },
 };
 
 static struct s3c2410_platform_i2c i2c1_pdata = {
-- 
1.7.7.3

^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH 4/7] ARM: S3C64XX: Improve logging of unknown Cragganmore module types
  2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
  2011-11-29 13:30   ` [PATCH 2/7] ARM: S3C64XX: Use software initiated powerdown for Cragganmore Mark Brown
  2011-11-29 13:30   ` [PATCH 3/7] ARM: S3C64XX: Configure WM1250 EV1 GPIOs on Cragganmore Mark Brown
@ 2011-11-29 13:30   ` Mark Brown
  2011-11-29 13:30   ` [PATCH 5/7] ARM: S3C64XX: Run Tobermory interrupts in the default mode Mark Brown
                     ` (2 subsequent siblings)
  5 siblings, 0 replies; 10+ messages in thread
From: Mark Brown @ 2011-11-29 13:30 UTC (permalink / raw)
  To: linux-arm-kernel

As our ID table is populated with hexidecimal values it makes sense to log
unknown module IDs in hexidecimal. It's also helpful to display board
revisions as 1 based rather than 0 based as that's the numbering system
used for the hardware (and what we do when announcing known modules).

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
 arch/arm/mach-s3c64xx/mach-crag6410-module.c |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
index 6666856..003c171 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
@@ -154,8 +154,8 @@ static __devinit int wlf_gf_module_probe(struct i2c_client *i2c,
 					"Failed to register dev: %d\n", ret);
 		}
 	} else {
-		dev_warn(&i2c->dev, "Unknown module ID %d revision %d\n",
-			 id, rev);
+		dev_warn(&i2c->dev, "Unknown module ID 0x%x revision %d\n",
+			 id, rev + 1);
 	}
 
 	return 0;
-- 
1.7.7.3

^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH 5/7] ARM: S3C64XX: Run Tobermory interrupts in the default mode
  2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
                     ` (2 preceding siblings ...)
  2011-11-29 13:30   ` [PATCH 4/7] ARM: S3C64XX: Improve logging of unknown Cragganmore module types Mark Brown
@ 2011-11-29 13:30   ` Mark Brown
  2011-11-29 13:30   ` [PATCH 6/7] ARM: S3C64XX: Hook up platform data for Kilchomin module on Cragganmore Mark Brown
  2011-11-29 13:30   ` [PATCH 7/7] ARM: S3C64XX: Hook up Littlemill audio card " Mark Brown
  5 siblings, 0 replies; 10+ messages in thread
From: Mark Brown @ 2011-11-29 13:30 UTC (permalink / raw)
  To: linux-arm-kernel

No need not to now that generic emulation is provided for the PMIC IRQ
controller.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
 arch/arm/mach-s3c64xx/mach-crag6410-module.c |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
index 003c171..6387ced 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
@@ -72,7 +72,6 @@ static struct wm8962_pdata wm8962_pdata __initdata = {
 		0x8000 | WM8962_GPIO_FN_DMICDAT,
 		WM8962_GPIO_FN_IRQ,    /* Open drain mode */
 	},
-	.irq_active_low = true,
 };
 
 static struct wm9081_pdata wm9081_pdata __initdata = {
-- 
1.7.7.3

^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH 6/7] ARM: S3C64XX: Hook up platform data for Kilchomin module on Cragganmore
  2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
                     ` (3 preceding siblings ...)
  2011-11-29 13:30   ` [PATCH 5/7] ARM: S3C64XX: Run Tobermory interrupts in the default mode Mark Brown
@ 2011-11-29 13:30   ` Mark Brown
  2011-11-29 13:30   ` [PATCH 7/7] ARM: S3C64XX: Hook up Littlemill audio card " Mark Brown
  5 siblings, 0 replies; 10+ messages in thread
From: Mark Brown @ 2011-11-29 13:30 UTC (permalink / raw)
  To: linux-arm-kernel

Now that the WM5100 driver is merged add some initial platform data for
the WM5100 on Kilchomin.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
 arch/arm/mach-s3c64xx/mach-crag6410-module.c |   30 ++++++++++++++++++++++++++
 1 files changed, 30 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
index 6387ced..c492f75 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
@@ -15,12 +15,41 @@
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
 
+#include <sound/wm5100.h>
 #include <sound/wm8996.h>
 #include <sound/wm8962.h>
 #include <sound/wm9081.h>
 
 #include <mach/crag6410.h>
 
+static struct wm5100_pdata wm5100_pdata = {
+	.ldo_ena = S3C64XX_GPN(7),
+	.irq_flags = IRQF_TRIGGER_HIGH,
+	.gpio_base = CODEC_GPIO_BASE,
+
+	.in_mode = {
+		WM5100_IN_DIFF,
+		WM5100_IN_DIFF,
+		WM5100_IN_DIFF,
+		WM5100_IN_SE,
+	},
+
+	.hp_pol = CODEC_GPIO_BASE + 3,
+	.jack_modes = {
+		{ WM5100_MICDET_MICBIAS3, 0, 0 },
+		{ WM5100_MICDET_MICBIAS2, 1, 1 },
+	},
+
+	.gpio_defaults = {
+		0,
+		0,
+		0,
+		0,
+		0x2, /* IRQ: CMOS output */
+		0x3, /* CLKOUT: CMOS output */
+	},
+};
+
 static struct wm8996_retune_mobile_config wm8996_retune[] = {
 	{
 		.name = "Sub LPF",
@@ -90,6 +119,7 @@ static const struct i2c_board_info wm1254_devs[] = {
 
 static const struct i2c_board_info wm1255_devs[] = {
 	{ I2C_BOARD_INFO("wm5100", 0x1a),
+	  .platform_data = &wm5100_pdata,
 	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
 	},
 	{ I2C_BOARD_INFO("wm9081", 0x6c),
-- 
1.7.7.3

^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH 7/7] ARM: S3C64XX: Hook up Littlemill audio card on Cragganmore
  2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
                     ` (4 preceding siblings ...)
  2011-11-29 13:30   ` [PATCH 6/7] ARM: S3C64XX: Hook up platform data for Kilchomin module on Cragganmore Mark Brown
@ 2011-11-29 13:30   ` Mark Brown
  5 siblings, 0 replies; 10+ messages in thread
From: Mark Brown @ 2011-11-29 13:30 UTC (permalink / raw)
  To: linux-arm-kernel

The Littlemill audio card is an adaptor card which can take any 6220-EV1
CODEC daughtercard. Provide standard support for the use of WM8994 class
devices on the Littlemill card, configuring the MFD for WM8958 usage as
this part is a superset of all others and the driver will use runtime
detection to identify the actually fitted part given the configuration for
the superset.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
---
 arch/arm/mach-s3c64xx/include/mach/crag6410.h |    6 ++++--
 arch/arm/mach-s3c64xx/include/mach/irqs.h     |    2 +-
 arch/arm/mach-s3c64xx/mach-crag6410-module.c  |   21 +++++++++++++++++++++
 arch/arm/mach-s3c64xx/mach-crag6410.c         |    6 ++++++
 4 files changed, 32 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-s3c64xx/include/mach/crag6410.h b/arch/arm/mach-s3c64xx/include/mach/crag6410.h
index be9074e..5d55ab0 100644
--- a/arch/arm/mach-s3c64xx/include/mach/crag6410.h
+++ b/arch/arm/mach-s3c64xx/include/mach/crag6410.h
@@ -15,9 +15,11 @@
 
 #define BANFF_PMIC_IRQ_BASE		IRQ_BOARD_START
 #define GLENFARCLAS_PMIC_IRQ_BASE	(IRQ_BOARD_START + 64)
+#define CODEC_IRQ_BASE			(IRQ_BOARD_START + 128)
 
 #define PCA935X_GPIO_BASE		GPIO_BOARD_START
-#define CODEC_GPIO_BASE		(GPIO_BOARD_START + 8)
-#define GLENFARCLAS_PMIC_GPIO_BASE	(GPIO_BOARD_START + 16)
+#define CODEC_GPIO_BASE			(GPIO_BOARD_START + 8)
+#define GLENFARCLAS_PMIC_GPIO_BASE	(GPIO_BOARD_START + 32)
+#define BANFF_PMIC_GPIO_BASE		(GPIO_BOARD_START + 64)
 
 #endif
diff --git a/arch/arm/mach-s3c64xx/include/mach/irqs.h b/arch/arm/mach-s3c64xx/include/mach/irqs.h
index 443f85b..96d60e0 100644
--- a/arch/arm/mach-s3c64xx/include/mach/irqs.h
+++ b/arch/arm/mach-s3c64xx/include/mach/irqs.h
@@ -169,7 +169,7 @@
 #define IRQ_BOARD_START (IRQ_EINT_GROUP9_BASE + IRQ_EINT_GROUP9_NR + 1)
 
 #ifdef CONFIG_MACH_WLF_CRAGG_6410
-#define IRQ_BOARD_NR 128
+#define IRQ_BOARD_NR 160
 #elif defined(CONFIG_SMDK6410_WM1190_EV1)
 #define IRQ_BOARD_NR 64
 #elif defined(CONFIG_SMDK6410_WM1192_EV1)
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
index c492f75..3fa7ebc 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c
@@ -14,6 +14,7 @@
 
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
+#include <linux/mfd/wm8994/pdata.h>
 
 #include <sound/wm5100.h>
 #include <sound/wm8996.h>
@@ -133,6 +134,24 @@ static const struct i2c_board_info wm1259_devs[] = {
 	},
 };
 
+static struct wm8994_pdata wm8994_pdata = {
+	.gpio_base = CODEC_GPIO_BASE,
+	.gpio_defaults = {
+		0x3,          /* IRQ out, active high, CMOS */
+	},
+	.irq_base = CODEC_IRQ_BASE,
+	.ldo = {
+		{ .supply = "WALLVDD" },
+		{ .supply = "WALLVDD" },
+	},
+};
+
+static const struct i2c_board_info wm1277_devs[] = {
+	{ I2C_BOARD_INFO("wm8958", 0x1a),  /* WM8958 is the superset */
+	  .platform_data = &wm8994_pdata,
+	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
+	},
+};
 
 static __devinitdata const struct {
 	u8 id;
@@ -154,6 +173,8 @@ static __devinitdata const struct {
 	{ .id = 0x3b, .name = "1255-EV1 Kilchoman",
 	  .i2c_devs = wm1255_devs, .num_i2c_devs = ARRAY_SIZE(wm1255_devs) },
 	{ .id = 0x3c, .name = "1273-EV1 Longmorn" },
+	{ .id = 0x3d, .name = "1277-EV1 Littlemill",
+	  .i2c_devs = wm1277_devs, .num_i2c_devs = ARRAY_SIZE(wm1277_devs) },
 };
 
 static __devinit int wlf_gf_module_probe(struct i2c_client *i2c,
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c
index 05f598f..ac9514a 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410.c
@@ -289,6 +289,11 @@ static struct platform_device speyside_wm8962_device = {
 	.id		= -1,
 };
 
+static struct platform_device littlemill_device = {
+	.name		= "littlemill",
+	.id		= -1,
+};
+
 static struct regulator_consumer_supply wallvdd_consumers[] = {
 	REGULATOR_SUPPLY("SPKVDD1", "1-001a"),
 	REGULATOR_SUPPLY("SPKVDD2", "1-001a"),
@@ -341,6 +346,7 @@ static struct platform_device *crag6410_devices[] __initdata = {
 	&crag6410_backlight_device,
 	&speyside_device,
 	&speyside_wm8962_device,
+	&littlemill_device,
 	&lowland_device,
 	&wallvdd_device,
 };
-- 
1.7.7.3

^ permalink raw reply related	[flat|nested] 10+ messages in thread

* [PATCH 0/7] Cragganmore updates for 3.3
  2011-11-29 13:30 [PATCH 0/7] Cragganmore updates for 3.3 Mark Brown
  2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
@ 2011-12-01 10:29 ` Kukjin Kim
  2011-12-01 11:37   ` Mark Brown
  1 sibling, 1 reply; 10+ messages in thread
From: Kukjin Kim @ 2011-12-01 10:29 UTC (permalink / raw)
  To: linux-arm-kernel

Mark Brown wrote:
> 
> This patch series is all the pending updates for Cragganmore for 3.3.
> With the exception of the final patch for Littlemill they've all been
> posted before, some a while ago now, but I've not seen any feedback yet.
> They're all available on a git branch in case it's helpful to pull them:
> 
> The following changes since commit
> caca6a03d365883564885f2c1da3e88dcf65d139:
> 
>   Linux 3.2-rc3 (2011-11-23 20:20:28 -0800)
> 
> are available in the git repository at:
>   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc.git
> updates/cragganmore
> 
> Mark Brown (7):
>       ARM: S3C64XX: Raise the frequency of the second I2C bus on
> Cragganmore
>       ARM: S3C64XX: Use software initiated powerdown for Cragganmore
>       ARM: S3C64XX: Configure WM1250 EV1 GPIOs on Cragganmore
>       ARM: S3C64XX: Improve logging of unknown Cragganmore module types
>       ARM: S3C64XX: Run Tobermory interrupts in the default mode
>       ARM: S3C64XX: Hook up platform data for Kilchomin module on
> Cragganmore
>       ARM: S3C64XX: Hook up Littlemill audio card on Cragganmore
> 
>  arch/arm/mach-s3c64xx/include/mach/crag6410.h |    6 ++-
>  arch/arm/mach-s3c64xx/include/mach/irqs.h     |    2 +-
>  arch/arm/mach-s3c64xx/mach-crag6410-module.c  |   56
> +++++++++++++++++++++++-
>  arch/arm/mach-s3c64xx/mach-crag6410.c         |   30 ++++++++++++-
>  4 files changed, 86 insertions(+), 8 deletions(-)

Looks ok, will apply this series.

And as a note, I'm thinking about the handling of different
IRQ_BOARD_NR...but I'm not sure it is really needed or not :)

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH 0/7] Cragganmore updates for 3.3
  2011-12-01 10:29 ` [PATCH 0/7] Cragganmore updates for 3.3 Kukjin Kim
@ 2011-12-01 11:37   ` Mark Brown
  0 siblings, 0 replies; 10+ messages in thread
From: Mark Brown @ 2011-12-01 11:37 UTC (permalink / raw)
  To: linux-arm-kernel

On Thu, Dec 01, 2011 at 07:29:49PM +0900, Kukjin Kim wrote:

> And as a note, I'm thinking about the handling of different
> IRQ_BOARD_NR...but I'm not sure it is really needed or not :)

Yeah, it's annoying.  I believe that converting to sparse IRQs would
avoid the issue.

^ permalink raw reply	[flat|nested] 10+ messages in thread

end of thread, other threads:[~2011-12-01 11:37 UTC | newest]

Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-11-29 13:30 [PATCH 0/7] Cragganmore updates for 3.3 Mark Brown
2011-11-29 13:30 ` [PATCH 1/7] ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore Mark Brown
2011-11-29 13:30   ` [PATCH 2/7] ARM: S3C64XX: Use software initiated powerdown for Cragganmore Mark Brown
2011-11-29 13:30   ` [PATCH 3/7] ARM: S3C64XX: Configure WM1250 EV1 GPIOs on Cragganmore Mark Brown
2011-11-29 13:30   ` [PATCH 4/7] ARM: S3C64XX: Improve logging of unknown Cragganmore module types Mark Brown
2011-11-29 13:30   ` [PATCH 5/7] ARM: S3C64XX: Run Tobermory interrupts in the default mode Mark Brown
2011-11-29 13:30   ` [PATCH 6/7] ARM: S3C64XX: Hook up platform data for Kilchomin module on Cragganmore Mark Brown
2011-11-29 13:30   ` [PATCH 7/7] ARM: S3C64XX: Hook up Littlemill audio card " Mark Brown
2011-12-01 10:29 ` [PATCH 0/7] Cragganmore updates for 3.3 Kukjin Kim
2011-12-01 11:37   ` Mark Brown

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).