[PATCH] omap3_beagle: init uart2 for beagle rev AX/BX only

[tony@atomide.com (Tony Lindgren)]

Hi,

Looking at this again..

* Govindraj.R <govindraj.raja@ti.com> [120306 00:34]:
> From: "Govindraj.R" <govindraj.raja@ti.com>
> 
> All beagle boards rev > AX/BX have external usb hubs connected to ehci
> interface, external hub/peripheral uses a nreset sequence for which
> uart2_rx.gpio_147 pin in mux mode4(USB2HS_nRST) is used on all beagle
> boards expect rev Ax/BX.
> (Reference to all beagle boards rev schematics:
> http://beagleboard.org/hardware/design)
> 
> Initialising uart2 will lead to serial init taking over uart2_rx pin
> so init uart2_rx pin mux only for Beagle AX/BX rev boards.
> Dont init uart2 for all other boards allowing usb_ehci functionality.

OK so the above got fixed for the muxing part with commit
bce492c04ba8fc66a4ea0a52b181ba255daaaf54.
 
> To initialise individual uart port by id utilise and modify the existing
> available func. omap_serial_board_init.

This makes sense as board specific fixes.
 
> --- a/arch/arm/mach-omap2/board-omap3beagle.c
> +++ b/arch/arm/mach-omap2/board-omap3beagle.c
> @@ -126,6 +126,7 @@ static void __init omap3_beagle_init_rev(void)
>  		beagle_config.mmc1_gpio_wp = 29;
>  		beagle_config.reset_gpio = 170;
>  		beagle_config.usr_button_gpio = 7;
> +		omap_serial_board_init(NULL, 1);
>  		break;
>  	case 6:
>  		printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
> @@ -528,7 +529,10 @@ static void __init omap3_beagle_init(void)
>  	platform_add_devices(omap3_beagle_devices,
>  			ARRAY_SIZE(omap3_beagle_devices));
>  	omap_display_init(&beagle_dss_data);
> -	omap_serial_init();
> +	omap_serial_board_init(NULL, 0);
> +	omap_serial_board_init(NULL, 2);
> +	omap_serial_board_init(NULL, 3);
> +
>  	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
>  				  mt46h32m32lf6_sdrc_params);
>  

So this still looks valid, except now you also add the muxing for the
uart pins instead of NULL? Note that you could define OMAP3_UART1_DEFAULT_PINS
etc in some header.

> --- a/arch/arm/mach-omap2/serial.c
> +++ b/arch/arm/mach-omap2/serial.c
> @@ -393,30 +393,32 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
>  /**
>   * omap_serial_board_init() - initialize all supported serial ports
>   * @info: platform specific data pointer
> + * @port_id: uart port number to be initialised
>   *
> - * Initializes all available UARTs as serial ports. Platforms
> + * Initializes individual UARTs as serial ports. Platforms
>   * can call this function when they want to have default behaviour
> - * for serial ports (e.g initialize them all as serial ports).
> + * for serial ports (e.g initialize individual serial ports based on port id).
>   */
> -void __init omap_serial_board_init(struct omap_uart_port_info *info)
> +void __init omap_serial_board_init(struct omap_uart_port_info *info, u8 port_id)
>  {
>  	struct omap_uart_state *uart;
>  	struct omap_board_data bdata;
>  
> -	list_for_each_entry(uart, &uart_list, node) {
> -		bdata.id = uart->num;
> -		bdata.flags = 0;
> -		bdata.pads = NULL;
> -		bdata.pads_cnt = 0;
> -
> -		if (cpu_is_omap44xx() || cpu_is_omap34xx())
> -			omap_serial_fill_default_pads(&bdata);
> -
> -		if (!info)
> -			omap_serial_init_port(&bdata, NULL);
> -		else
> -			omap_serial_init_port(&bdata, &info[uart->num]);
> -	}
> +	list_for_each_entry(uart, &uart_list, node)
> +		if (uart->num == port_id) {
> +			bdata.id = uart->num;
> +			bdata.flags = 0;
> +			bdata.pads = NULL;
> +			bdata.pads_cnt = 0;
> +
> +			if (!cpu_is_omap24xx())
> +				omap_serial_fill_default_pads(&bdata);
> +
> +			if (!info)
> +				omap_serial_init_port(&bdata, NULL);
> +			else
> +				omap_serial_init_port(&bdata, info);
> +		}
>  }
> @@ -428,5 +430,8 @@ void __init omap_serial_board_init(struct omap_uart_port_info *info)
>   */
>  void __init omap_serial_init(void)
>  {
> -	omap_serial_board_init(NULL);
> +	struct omap_uart_state *uart;
> +
> +	list_for_each_entry(uart, &uart_list, node)
> +		omap_serial_board_init(NULL, uart->num);
>  }

Is this fix still needed? If so, it should probably be a separate fix
with it's own description.  

Regards,

Tony