[PATCH v5 0/4] atmel-mci device tree support

[PATCH v5 0/4] atmel-mci device tree support

[ludovic.desroches at atmel.com]

Hi,

This patch-set adds device tree support for atmel-mci.

Regards

Ludovic

v5:
- cleanup
- split dts commit: one for SOCs, one for boards

v4:
- cleanup
- add extra chips and boards for atmel-mci dt support

v3:
- use cd-inverted instead of cd-invert to follow mmc common binding.
- don't assign a pointer to pdev->dev.platform.
- add mci controller nodes to other chips and boards.
- put all dts file changes together.

v2:
- squash patch v1 2/4 and 3/4.
- change atmci_get_of_slots to atmci_of_init and manage pdata allocation into
it.
- correct potential issue (e.g. having only one slot which is not slot0 into
the dt) about slots by adding a reg property corresponding to the slot id.

[PATCH 1/4 v5] mmc: atmel-mci: add device tree support

[ludovic.desroches at atmel.com]

From: Ludovic Desroches <ludovic.desroches@atmel.com>

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
---
 .../devicetree/bindings/mmc/atmel-hsmci.txt        |   67 +++++++++++++++
 drivers/mmc/host/atmel-mci.c                       |   85 +++++++++++++++++++-
 2 files changed, 150 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mmc/atmel-hsmci.txt

diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
new file mode 100644
index 0000000..81c20cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
@@ -0,0 +1,67 @@
+* Atmel High Speed MultiMedia Card Interface
+
+This controller on atmel products provides an interface for MMC, SD and SDIO
+types of memory cards.
+
+1) MCI node
+
+Required properties:
+- compatible: no blank "atmel,hsmci"
+- reg: should contain HSMCI registers location and length
+- interrupts: should contain HSMCI interrupt number
+- #address-cells: should be one. The cell is the slot id.
+- #size-cells: should be zero.
+- at least one slot node
+
+The node contains child nodes for each slot that the platform uses
+
+Example MCI node:
+
+mmc0: mmc at f0008000 {
+	compatible = "atmel,hsmci";
+	reg = <0xf0008000 0x600>;
+	interrupts = <12 4>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	[ child node definitions...]
+};
+
+2) slot nodes
+
+Required properties:
+- reg: should contain the slot id.
+- bus-width: number of data lines connected to the controller
+
+Optional properties:
+- cd-gpios: specify GPIOs for card detection
+- cd-inverted: invert the value of external card detect gpio line
+- wp-gpios: specify GPIOs for write protection
+
+Example slot node:
+
+slot at 0 {
+	reg = <0>;
+	bus-width = <4>;
+	cd-gpios = <&pioD 15 0>
+	cd-inverted;
+};
+
+Example full MCI node:
+mmc0: mmc at f0008000 {
+	compatible = "atmel,hsmci";
+	reg = <0xf0008000 0x600>;
+	interrupts = <12 4>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	slot at 0 {
+		reg = <0>;
+		bus-width = <4>;
+		cd-gpios = <&pioD 15 0>
+		cd-inverted;
+	};
+	slot at 1 {
+		reg = <1>;
+		bus-width = <4>;
+	};
+};
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index f2c115e..47421fc 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -19,6 +19,9 @@
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
 #include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/platform_device.h>
 #include <linux/scatterlist.h>
 #include <linux/seq_file.h>
@@ -493,6 +496,70 @@ err:
 	dev_err(&mmc->class_dev, "failed to initialize debugfs for slot\n");
 }
 
+#if defined(CONFIG_OF)
+static const struct of_device_id atmci_dt_ids[] = {
+	{ .compatible = "atmel,hsmci" },
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmci_dt_ids);
+
+static struct mci_platform_data __devinit*
+atmci_of_init(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *cnp;
+	struct mci_platform_data *pdata;
+	u32 slot_id;
+
+	if (!np) {
+		dev_err(&pdev->dev, "device node not found\n");
+		return ERR_PTR(-EINVAL);
+	}
+
+	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata) {
+		dev_err(&pdev->dev, "could not allocate memory for pdata\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	for_each_child_of_node(np, cnp) {
+		if (of_property_read_u32(cnp, "reg", &slot_id)) {
+			dev_warn(&pdev->dev, "reg property is missing for %s\n",
+				 cnp->full_name);
+			continue;
+		}
+
+		if (slot_id >= ATMCI_MAX_NR_SLOTS) {
+			dev_warn(&pdev->dev, "can't have more than %d slots\n",
+			         ATMCI_MAX_NR_SLOTS);
+			break;
+		}
+
+		if (of_property_read_u32(cnp, "bus-width",
+		                         &pdata->slot[slot_id].bus_width))
+			pdata->slot[slot_id].bus_width = 1;
+
+		pdata->slot[slot_id].detect_pin =
+			of_get_named_gpio(cnp, "cd-gpios", 0);
+
+		pdata->slot[slot_id].detect_is_active_high =
+			of_property_read_bool(cnp, "cd-inverted");
+
+		pdata->slot[slot_id].wp_pin =
+			of_get_named_gpio(cnp, "wp-gpios", 0);
+	}
+
+	return pdata;
+}
+#else /* CONFIG_OF */
+static inline struct mci_platform_data*
+atmci_of_init(struct platform_device *dev)
+{
+	return ERR_PTR(-EINVAL);
+}
+#endif
+
 static inline unsigned int atmci_get_version(struct atmel_mci *host)
 {
 	return atmci_readl(host, ATMCI_VERSION) & 0x00000fff;
@@ -2038,6 +2105,13 @@ static int __init atmci_init_slot(struct atmel_mci *host,
 	slot->sdc_reg = sdc_reg;
 	slot->sdio_irq = sdio_irq;
 
+	dev_dbg(&mmc->class_dev,
+	        "slot[%u]: bus_width=%u, detect_pin=%d, "
+		"detect_is_active_high=%s, wp_pin=%d\n",
+		id, slot_data->bus_width, slot_data->detect_pin,
+		slot_data->detect_is_active_high ? "true" : "false",
+		slot_data->wp_pin);
+
 	mmc->ops = &atmci_ops;
 	mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512);
 	mmc->f_max = host->bus_hz / 2;
@@ -2258,8 +2332,14 @@ static int __init atmci_probe(struct platform_device *pdev)
 	if (!regs)
 		return -ENXIO;
 	pdata = pdev->dev.platform_data;
-	if (!pdata)
-		return -ENXIO;
+	if (!pdata) {
+		pdata = atmci_of_init(pdev);
+		if (IS_ERR(pdata)) {
+			dev_err(&pdev->dev, "platform data not available\n");
+			return PTR_ERR(pdata);
+		}
+	}
+
 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0)
 		return irq;
@@ -2477,6 +2557,7 @@ static struct platform_driver atmci_driver = {
 	.driver		= {
 		.name		= "atmel_mci",
 		.pm		= ATMCI_PM_OPS,
+		.of_match_table	= of_match_ptr(atmci_dt_ids),
 	},
 };
 
-- 
1.7.5.4

[PATCH 2/4 v5] ARM: at91: add clocks for DT entries

[ludovic.desroches at atmel.com]

From: Ludovic Desroches <ludovic.desroches@atmel.com>

Add clocks to clock lookup table for DT entries.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
 arch/arm/mach-at91/at91sam9260.c |    1 +
 arch/arm/mach-at91/at91sam9263.c |    2 ++
 arch/arm/mach-at91/at91sam9g45.c |    2 ++
 arch/arm/mach-at91/at91sam9n12.c |    1 +
 arch/arm/mach-at91/at91sam9x5.c  |    2 ++
 5 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index 2b1e438..ddba004 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -226,6 +226,7 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("t1_clk", "fffdc000.timer", &tc4_clk),
 	CLKDEV_CON_DEV_ID("t2_clk", "fffdc000.timer", &tc5_clk),
 	CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &ohci_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "fffa8000.mmc", &mmc_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
 	CLKDEV_CON_ID("pioA", &pioA_clk),
diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c
index 0eb20f9..f165b25 100644
--- a/arch/arm/mach-at91/at91sam9263.c
+++ b/arch/arm/mach-at91/at91sam9263.c
@@ -211,6 +211,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("hclk", "a00000.ohci", &ohci_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "fff80000.mmc", &mmc0_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "fff84000.mmc", &mmc1_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c
index 4792682..aa24e82 100644
--- a/arch/arm/mach-at91/at91sam9g45.c
+++ b/arch/arm/mach-at91/at91sam9g45.c
@@ -242,6 +242,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("t0_clk", "fffd4000.timer", &tcb0_clk),
 	CLKDEV_CON_DEV_ID("hclk", "700000.ohci", &uhphs_clk),
 	CLKDEV_CON_DEV_ID("ehci_clk", "800000.ehci", &uhphs_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "fff80000.mmc", &mmc0_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "fffd0000.mmc", &mmc1_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk),
 	CLKDEV_CON_ID("pioA", &pioA_clk),
diff --git a/arch/arm/mach-at91/at91sam9n12.c b/arch/arm/mach-at91/at91sam9n12.c
index 0849466..cce4e0f 100644
--- a/arch/arm/mach-at91/at91sam9n12.c
+++ b/arch/arm/mach-at91/at91sam9n12.c
@@ -168,6 +168,7 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("usart", "f8028000.serial", &usart3_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "f0008000.mmc", &mmc_clk),
 	CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma_clk),
 	CLKDEV_CON_ID("pioA", &pioAB_clk),
 	CLKDEV_CON_ID("pioB", &pioAB_clk),
diff --git a/arch/arm/mach-at91/at91sam9x5.c b/arch/arm/mach-at91/at91sam9x5.c
index 1b144b4..de86e37 100644
--- a/arch/arm/mach-at91/at91sam9x5.c
+++ b/arch/arm/mach-at91/at91sam9x5.c
@@ -231,6 +231,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb0_clk),
 	CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma0_clk),
 	CLKDEV_CON_DEV_ID("dma_clk", "ffffee00.dma-controller", &dma1_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "f0008000.mmc", &mmc0_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "f000c000.mmc", &mmc1_clk),
 	CLKDEV_CON_ID("pioA", &pioAB_clk),
 	CLKDEV_CON_ID("pioB", &pioAB_clk),
 	CLKDEV_CON_ID("pioC", &pioCD_clk),
-- 
1.7.5.4

[PATCH 3/4 v5] ARM: dts: add nodes for atmel hsmci controllers for atmel SOCs

[ludovic.desroches at atmel.com]

From: Ludovic Desroches <ludovic.desroches@atmel.com>

Add mci controller nodes to atmel SOCs.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
---
 arch/arm/boot/dts/at91sam9260.dtsi |    9 +++++++++
 arch/arm/boot/dts/at91sam9263.dtsi |   18 ++++++++++++++++++
 arch/arm/boot/dts/at91sam9g45.dtsi |   18 ++++++++++++++++++
 arch/arm/boot/dts/at91sam9n12.dtsi |    9 +++++++++
 arch/arm/boot/dts/at91sam9x5.dtsi  |   18 ++++++++++++++++++
 5 files changed, 72 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index f449efc..ae54bf3 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -198,6 +198,15 @@
 				status = "disabled";
 			};
 
+			mmc0: mmc at fffa8000 {
+				compatible = "atmel,hsmci";
+				reg = <0xfffa800 0x600>;
+				interrupts = <9 4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
 			adc0: adc at fffe0000 {
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xfffe0000 0x100>;
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index 0209913..a327ebe 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -179,6 +179,24 @@
 				interrupts = <24 4>;
 				status = "disabled";
 			};
+
+			mmc0: mmc at fff80000 {
+				compatible = "atmel,hsmci";
+				reg = <0xfff80000 0x600>;
+				interrupts = <10 4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			mmc1: mmc at fff84000 {
+				compatible = "atmel,hsmci";
+				reg = <0xfff84000 0x600>;
+				interrupts = <11 4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 		};
 
 		nand0: nand at 40000000 {
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 7dbccaf..0360bf8 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -236,6 +236,24 @@
 					trigger-value = <0x6>;
 				};
 			};
+
+			mmc0: mmc at fff80000 {
+				compatible = "atmel,hsmci";
+				reg = <0xfff80000 0x600>;
+				interrupts = <11 4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			mmc1: mmc at fffd0000 {
+				compatible = "atmel,hsmci";
+				reg = <0xfffd0000 0x600>;
+				interrupts = <29 4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 		};
 
 		nand0: nand at 40000000 {
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index cb84de7..f3e03fb 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -82,6 +82,15 @@
 				reg = <0xfffffe10 0x10>;
 			};
 
+			mmc0: mmc at f0008000 {
+				compatible = "atmel,hsmci";
+				reg = <0xf0008000 0x600>;
+				interrupts = <12 4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
 			tcb0: timer at f8008000 {
 				compatible = "atmel,at91sam9x5-tcb";
 				reg = <0xf8008000 0x100>;
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index 6b3ef43..4e8125b 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -228,6 +228,24 @@
 					trigger-value = <0x6>;
 				};
 			};
+
+			mmc0: mmc at f0008000 {
+				compatible = "atmel,hsmci";
+				reg = <0xf0008000 0x600>;
+				interrupts = <12 4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			mmc1: mmc at f000c000 {
+				compatible = "atmel,hsmci";
+				reg = <0xf000c000 0x600>;
+				interrupts = <26 4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 		};
 
 		nand0: nand at 40000000 {
-- 
1.7.5.4

[PATCH 4/4 v5] ARM: dts: add nodes for atmel hsmci controllers for atmel boards

[ludovic.desroches at atmel.com]

From: Ludovic Desroches <ludovic.desroches@atmel.com>

Add mci controller nodes to atmel boards.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
---
 arch/arm/boot/dts/at91sam9263ek.dts         |   10 ++++++++++
 arch/arm/boot/dts/at91sam9g20ek_2mmc.dts    |   12 ++++++++++++
 arch/arm/boot/dts/at91sam9g20ek_common.dtsi |    9 +++++++++
 arch/arm/boot/dts/at91sam9g25ek.dts         |   18 ++++++++++++++++++
 arch/arm/boot/dts/at91sam9m10g45ek.dts      |   19 +++++++++++++++++++
 arch/arm/boot/dts/at91sam9n12ek.dts         |    9 +++++++++
 6 files changed, 77 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
index f86ac4b..05028ed 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/at91sam9263ek.dts
@@ -50,6 +50,16 @@
 				atmel,vbus-gpio = <&pioA 25 0>;
 				status = "okay";
 			};
+
+			mmc0: mmc at fff80000 {
+				status = "okay";
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioE 18 0>;
+					wp-gpios = <&pioE 19 0>;
+				};
+			};
 		};
 
 		nand0: nand at 40000000 {
diff --git a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts b/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts
index f1b2e14..684b229 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts
+++ b/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts
@@ -12,6 +12,18 @@
 	model = "Atmel at91sam9g20ek 2 mmc";
 	compatible = "atmel,at91sam9g20ek_2mmc", "atmel,at91sam9g20", "atmel,at91sam9";
 
+	ahb {
+		apb{
+			mmc0: mmc at fffa8000 {
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioC 2 0>;
+				};
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
index b06c0db..7da326a 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
@@ -51,6 +51,15 @@
 				atmel,vbus-gpio = <&pioC 5 0>;
 				status = "okay";
 			};
+
+			mmc0: mmc at fffa8000 {
+				status = "okay";
+				slot at 1 {
+					reg = <1>;
+					bus-width = <4>;
+					cd-gpios = <&pioC 9 0>;
+				};
+			};
 		};
 
 		nand0: nand at 40000000 {
diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/at91sam9g25ek.dts
index 7829a4d..422a9fb 100644
--- a/arch/arm/boot/dts/at91sam9g25ek.dts
+++ b/arch/arm/boot/dts/at91sam9g25ek.dts
@@ -32,6 +32,24 @@
 				phy-mode = "rmii";
 				status = "okay";
 			};
+
+			mmc0: mmc at f0008000 {
+				status = "okay";
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 15 0>;
+				};
+			};
+
+			mmc1: mmc at f000c000 {
+				status = "okay";
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 14 0>;
+				};
+			};
 		};
 
 		usb0: ohci at 00600000 {
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index a3633bd..7a7b571 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -46,6 +46,25 @@
 				phy-mode = "rmii";
 				status = "okay";
 			};
+
+			mmc0: mmc at fff80000 {
+				status = "okay";
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 10 0>;
+				};
+			};
+
+			mmc1: mmc at fffd0000 {
+				status = "okay";
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 11 0>;
+					wp-gpios = <&pioD 29 0>;
+				};
+			};
 		};
 
 		nand0: nand at 40000000 {
diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index f4e43e3..44b42d9 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -37,6 +37,15 @@
 			dbgu: serial at fffff200 {
 				status = "okay";
 			};
+
+			mmc0: mmc at f0008000 {
+				status = "okay";
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioA 7 0>;
+				};
+			};
 		};
 
 		nand0: nand at 40000000 {
-- 
1.7.5.4

[PATCH 3/4 v5] ARM: dts: add nodes for atmel hsmci controllers for atmel SOCs

[Jean-Christophe PLAGNIOL-VILLARD]

On 17:15 Thu 24 May     , ludovic.desroches at atmel.com wrote:
> From: Ludovic Desroches <ludovic.desroches@atmel.com>
> 
> Add mci controller nodes to atmel SOCs.
> 
> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Best Regards,
J.

[PATCH 4/4 v5] ARM: dts: add nodes for atmel hsmci controllers for atmel boards

[Jean-Christophe PLAGNIOL-VILLARD]

On 17:15 Thu 24 May     , ludovic.desroches at atmel.com wrote:
> From: Ludovic Desroches <ludovic.desroches@atmel.com>
> 
> Add mci controller nodes to atmel boards.
> 
> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Best Regards,
J.

[PATCH 1/4 v5] mmc: atmel-mci: add device tree support

[Jean-Christophe PLAGNIOL-VILLARD]

On 17:15 Thu 24 May     , ludovic.desroches at atmel.com wrote:
> From: Ludovic Desroches <ludovic.desroches@atmel.com>
> 
> Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
> ---
>  .../devicetree/bindings/mmc/atmel-hsmci.txt        |   67 +++++++++++++++
>  drivers/mmc/host/atmel-mci.c                       |   85 +++++++++++++++++++-
>  2 files changed, 150 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
> 
> diff --git a/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
> new file mode 100644
> index 0000000..81c20cc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/atmel-hsmci.txt
> @@ -0,0 +1,67 @@
> +* Atmel High Speed MultiMedia Card Interface
> +
> +This controller on atmel products provides an interface for MMC, SD and SDIO
> +types of memory cards.
> +
> +1) MCI node
> +
> +Required properties:
> +- compatible: no blank "atmel,hsmci"
> +- reg: should contain HSMCI registers location and length
> +- interrupts: should contain HSMCI interrupt number
> +- #address-cells: should be one. The cell is the slot id.
> +- #size-cells: should be zero.
> +- at least one slot node
> +
> +The node contains child nodes for each slot that the platform uses
> +
> +Example MCI node:
> +
> +mmc0: mmc at f0008000 {
> +	compatible = "atmel,hsmci";
> +	reg = <0xf0008000 0x600>;
> +	interrupts = <12 4>;
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	[ child node definitions...]
> +};
> +
> +2) slot nodes
> +
> +Required properties:
> +- reg: should contain the slot id.
> +- bus-width: number of data lines connected to the controller
> +
> +Optional properties:
> +- cd-gpios: specify GPIOs for card detection
> +- cd-inverted: invert the value of external card detect gpio line
> +- wp-gpios: specify GPIOs for write protection
> +
> +Example slot node:
> +
> +slot at 0 {
> +	reg = <0>;
> +	bus-width = <4>;
> +	cd-gpios = <&pioD 15 0>
> +	cd-inverted;
> +};
> +
> +Example full MCI node:
> +mmc0: mmc at f0008000 {
> +	compatible = "atmel,hsmci";
> +	reg = <0xf0008000 0x600>;
> +	interrupts = <12 4>;
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	slot at 0 {
> +		reg = <0>;
> +		bus-width = <4>;
> +		cd-gpios = <&pioD 15 0>
> +		cd-inverted;
> +	};
> +	slot at 1 {
> +		reg = <1>;
> +		bus-width = <4>;
> +	};
> +};
> diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
> index f2c115e..47421fc 100644
> --- a/drivers/mmc/host/atmel-mci.c
> +++ b/drivers/mmc/host/atmel-mci.c
> @@ -19,6 +19,9 @@
>  #include <linux/interrupt.h>
>  #include <linux/ioport.h>
>  #include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
>  #include <linux/platform_device.h>
>  #include <linux/scatterlist.h>
>  #include <linux/seq_file.h>
> @@ -493,6 +496,70 @@ err:
>  	dev_err(&mmc->class_dev, "failed to initialize debugfs for slot\n");
>  }
>  
> +#if defined(CONFIG_OF)
> +static const struct of_device_id atmci_dt_ids[] = {
> +	{ .compatible = "atmel,hsmci" },
> +	{ /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmci_dt_ids);
> +
> +static struct mci_platform_data __devinit*
> +atmci_of_init(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct device_node *cnp;
> +	struct mci_platform_data *pdata;
> +	u32 slot_id;
> +
> +	if (!np) {
> +		dev_err(&pdev->dev, "device node not found\n");
> +		return ERR_PTR(-EINVAL);
> +	}
> +
> +	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
> +	if (!pdata) {
> +		dev_err(&pdev->dev, "could not allocate memory for pdata\n");
> +		return ERR_PTR(-ENOMEM);
> +	}
> +
> +	for_each_child_of_node(np, cnp) {
> +		if (of_property_read_u32(cnp, "reg", &slot_id)) {
> +			dev_warn(&pdev->dev, "reg property is missing for %s\n",
> +				 cnp->full_name);
> +			continue;
> +		}
> +
> +		if (slot_id >= ATMCI_MAX_NR_SLOTS) {
> +			dev_warn(&pdev->dev, "can't have more than %d slots\n",
> +			         ATMCI_MAX_NR_SLOTS);
> +			break;
> +		}
> +
> +		if (of_property_read_u32(cnp, "bus-width",
> +		                         &pdata->slot[slot_id].bus_width))
> +			pdata->slot[slot_id].bus_width = 1;
> +
> +		pdata->slot[slot_id].detect_pin =
> +			of_get_named_gpio(cnp, "cd-gpios", 0);
> +
> +		pdata->slot[slot_id].detect_is_active_high =
> +			of_property_read_bool(cnp, "cd-inverted");
as this is going to be removed at once

please implement the gpio active low too

otherwise
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Best Regards,
J.