[PATCH v2] Visstrim M10: fix gpio handling.

[s.hauer@pengutronix.de (Sascha Hauer)]

On Fri, Jun 01, 2012 at 09:45:33AM +0200, Javier Martin wrote:
> Some GPIOs in Visstrim M10 are used without being registered.
> This leads to USB and video malfunctions. This patch registers
> those GPIOs to solve the issue.
> 
> Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>

Applied, thanks.

I added a 'ARM i.MX27:' prefix to the subject while applying. Please do
so next time, upstream gets picky about this.

Sascha

> ---
> Request all gpios using a single gpio_request_array() call.
> 
> ---
>  arch/arm/mach-imx/mach-imx27_visstrim_m10.c |   36 ++++++++++++++++++--------
>  1 files changed, 25 insertions(+), 11 deletions(-)
> 
> diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> index e8741f9..f00c0cc 100644
> --- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> +++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c
> @@ -116,6 +116,8 @@ static const int visstrim_m10_pins[] __initconst = {
>  	PB23_PF_USB_PWR,
>  	PB24_PF_USB_OC,
>  	/* CSI */
> +	TVP5150_RSTN | GPIO_GPIO | GPIO_OUT,
> +	TVP5150_PWDN | GPIO_GPIO | GPIO_OUT,
>  	PB10_PF_CSI_D0,
>  	PB11_PF_CSI_D1,
>  	PB12_PF_CSI_D2,
> @@ -138,6 +140,24 @@ static const int visstrim_m10_pins[] __initconst = {
>  	EXPBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
>  };
>  
> +static const struct gpio visstrim_m10_gpios[] __initconst = {
> +	{
> +		.gpio = TVP5150_RSTN,
> +		.flags = GPIOF_DIR_OUT | GPIOF_INIT_HIGH,
> +		.label = "tvp5150_rstn",
> +	},
> +	{
> +		.gpio = TVP5150_PWDN,
> +		.flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW,
> +		.label = "tvp5150_pwdn",
> +	},
> +	{
> +		.gpio = OTG_PHY_CS_GPIO,
> +		.flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW,
> +		.label = "usbotg_cs",
> +	},
> +};
> +
>  /* Camera */
>  static int visstrim_camera_power(struct device *dev, int on)
>  {
> @@ -181,13 +201,6 @@ static void __init visstrim_camera_init(void)
>  	struct platform_device *pdev;
>  	int dma;
>  
> -	/* Initialize tvp5150 gpios */
> -	mxc_gpio_mode(TVP5150_RSTN | GPIO_GPIO | GPIO_OUT);
> -	mxc_gpio_mode(TVP5150_PWDN | GPIO_GPIO | GPIO_OUT);
> -	gpio_set_value(TVP5150_RSTN, 1);
> -	gpio_set_value(TVP5150_PWDN, 0);
> -	ndelay(1);
> -
>  	gpio_set_value(TVP5150_PWDN, 1);
>  	ndelay(1);
>  	gpio_set_value(TVP5150_RSTN, 0);
> @@ -414,10 +427,6 @@ static struct i2c_board_info visstrim_m10_i2c_devices[] = {
>  /* USB OTG */
>  static int otg_phy_init(struct platform_device *pdev)
>  {
> -	gpio_set_value(OTG_PHY_CS_GPIO, 0);
> -
> -	mdelay(10);
> -
>  	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED);
>  }
>  
> @@ -474,6 +483,11 @@ static void __init visstrim_m10_board_init(void)
>  	if (ret)
>  		pr_err("Failed to setup pins (%d)\n", ret);
>  
> +	ret = gpio_request_array(visstrim_m10_gpios,
> +				ARRAY_SIZE(visstrim_m10_gpios));
> +	if (ret)
> +		pr_err("Failed to request gpios (%d)\n", ret);
> +
>  	imx27_add_imx_ssi(0, &visstrim_m10_ssi_pdata);
>  	imx27_add_imx_uart0(&uart_pdata);
>  
> -- 
> 1.7.0.4
> 
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |